Unable to luanch meeting room(Meeting place 2.x)

I having some issue with meeting place Web meeting .
Whenever i join the  web meeting room , i am getting the below error
System ERROR:
The meeting Room Couldn't connect to the cisco unified meeting place server,  please re-launch the meeting room or refresh your browser to restore the  connection
Note:
I- installed the proper Flash player, presenter adds on software
2- Browser TEST worked fine
3- I dont see any firewall rule blocking the connection
I will really appreciate your help on this issue.
Regards ,
Shaijal

Hello ,
I got solution for this issue.
There are two IP address for Meeting place express .
one for audio and meeting place access.
second ip is used for Web trafic .In my scenario i havn't done any DNS configuration for
my second IP.After the proper DNS change it statred working .
Thanks ,
Shaijal

Similar Messages

  • Cisco Meeting place 6.x unable to open admin page

    i am having meeting place 6.x .configure IP address to both NICs . Gateway SIM showing me s connected, But Web page of meeting place unable to display

    Please have a look at the ssl settings on the ASA: "show run | i ssl".
    You may not have strong ciphers enabled and the PC with the newer browser does not accept the default weak ciphers. I make it a habit to setup ASAs with:
    ssl encryption 3des-sha1 aes128-sha1 aes256-sha1 rc4-md5
    Those are all strong ciphers.

  • Meeting Place Express 2.1.1.2 Web Access Issue

    Hello all,
         I'am having an issue with a Meeting Place Express 2.1.1.2 server.  There was a power failure and now we can still access the server via dial-in but the web acess is not working.  From the CLI i run the mpx_sys status command and it says webservices is active.  The server has been restarted.  When I check the errorlog I see "unable to connect to webservices, trying again"  Anyone know what the issue might be? Thanks
    Jason

    Hello Hasnain,
    Have you tried the recovery procedures below:
    http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Express%2C_Release_2.x_--_Troubleshooting_System_Issues#Recovering_the_Password_for_the_root_Account
    If that doesnt work, you will need to open a TAC case and TAC will send you a password recovery .iso file to burn on a CD/DVD.
    Regards,
    Victor Dang.

  • Cisco Meeting Place Express 2.1.1.2 and not working anymore

    Hello, we currently have cisco meeting place express 2.1.1.2; however are now having issues with it.  We are unable to dial to the internal extension that was previously working to login to the meetings and only get a busy signal everytime. Furthermore, whenever someone tries to schedule a new meeting via the web form, it says "request to server timed out. please try again".
    I tried reaching out to Cisco TAC support; however it's no longer a supported item and am looking for assistance here.  The TAC engineer was able to help assist with updating the system clock; however I believe the problems started happening after we updated the clock and rebooted the server.  Now we are unable to schedule and attend any meetings (busy signal everytime) at all.  I tried restarting the server itself as well as via the command line.  I also now see an error during CLI restart, which I have listed directly below:
    Stopping MeetingPlace SNMP/R:                              [  OK  ]
    Stopping mpe-tomcat-main: bash: /root/.bashrc: Permission denied
                                                               [  OK  ]
    Stopping mpe-tomcat-securewebservices: bash: /root/.bashrc: Permission denied
                                                               [  OK  ]
    Shutting down breeze:                                      [  OK  ]
    Shutting down fmsmaster:                                   [  OK  ]
    Shutting down fmsadmin:                                    [  OK  ]
    Stopping MeetingPlace application: /etc/init.d/mpx_app: line 264:  4955 Segmentation fault      (core dumped) ${shutdown_bin} ${shutdown_arg_1} ${shutdown_arg_2} ${shutdown_arg_3} >>${non_verbose_shutdown_output} 2>&1
                                                               [FAILED]
        ERROR: returncode = 139
    Stopping MeetingPlace License Manager:                     [  OK  ]
    Stopping MeetingPlace database:                            [  OK  ]
    Stopping MeetingPlace Java RMI: Shutting down RMI Registry:
                                                               [  OK  ]
    Stopping Cisco MeetingPlace Express:                       [  OK  ]
    Starting MeetingPlace Java RMI: Starting RMI Registry:
    starting daemon
    mpxadmin
                                                               [  OK  ]
    Starting MeetingPlace database:                            [  OK  ]
    Starting MeetingPlace License Manager:                     [  OK  ]
    Starting MeetingPlace application:                         [  OK  ]
        already running
    Starting breeze:                                           [  OK  ]
    Starting fmsmaster:                                        [  OK  ]
    Starting fmsadmin:                                         [  OK  ]
    Starting mpe-tomcat-main: bash: /root/.bashrc: Permission denied
                                                               [  OK  ]
    Both the admin and user web interfaces work on the home pages, but can't seem to schedule any new meetings or login to any existing ones, with busy signal as well. Anyone have any ideas? We need assistance with this ASAP since it's our voice collaboration solution.  Thanks in advance for any help.                  

    Amlesh,
    Here is the pertinent output:
    /common/log/taos-log-a/core/core.1947.11.ConfSchd.1183266069
    /common/log/taos-log-a/core/core.1837.6.gyromain.bin.1183266161
    /common/log/taos-log-a/core/core.1859.6.cpgs.1183266206
    /common/log/taos-log-a/core/core.1951.11.ConfSchd.1184475669
    /common/log/taos-log-a/core/core.1946.11.ConfSchd.1185685269
    /common/log/taos-log-a/core/core.1836.6.gyromain.bin.1185685332
    /common/log/taos-log-a/core/core.1880.6.cca.1185685452
    /common/log/taos-log-a/core/core.1858.6.cpgs.1185685452
    /common/log/taos-log-a/core/core.1950.11.ConfSchd.1185771671
    /common/log/taos-log-a/core/core.1863.6.cpgs.1185771865
    /common/log/taos-log-a/core/core.1884.6.cca.1185771865
    /common/log/taos-log-a/core/core.1991.6.nmpagent.1185771865
    /common/log/taos-log-a/core/core.1950.11.ConfSchd.1185858067
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1188018079
    /common/log/taos-log-a/core/core.1969.11.ConfSchd.1188190869
    /common/log/taos-log-a/core/core.2008.6.vui.1188190988
    /common/log/taos-log-a/core/core.2029.6.nmpagent.1188190988
    /common/log/taos-log-a/core/core.1998.6.poclient.1188190988
    /common/log/taos-log-a/core/core.1970.11.ConfSchd.1189227671
    /common/log/taos-log-a/core/core.1862.6.gyromain.bin.1189227762
    /common/log/taos-log-a/core/core.1883.6.cpgs.1189227807
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1189918866
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1190005281
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1190178068
    /common/log/taos-log-a/core/core.1886.6.cca.1190178237
    /common/log/taos-log-a/core/core.2012.6.nmpagent.1190178237
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1191906070
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1191906162
    /common/log/taos-log-a/core/core.1886.6.cca.1191906248
    /common/log/taos-log-a/core/core.1865.6.cpgs.1191906248
    /common/log/taos-log-a/core/core.1950.11.ConfSchd.1192424479
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1192424571
    /common/log/taos-log-a/core/core.1863.6.cpgs.1192424613
    /common/log/taos-log-a/core/core.1951.11.ConfSchd.1192597270
    /common/log/taos-log-a/core/core.1969.11.ConfSchd.1192683669
    /common/log/taos-log-a/core/core.1903.6.cca.1192683817
    /common/log/taos-log-a/core/core.1951.11.ConfSchd.1193029270
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1193029360
    /common/log/taos-log-a/core/core.1864.6.cpgs.1193029400
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1193720467
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1193720565
    /common/log/taos-log-a/core/core.1864.6.cpgs.1193720610
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1195452071
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1195452170
    /common/log/taos-log-a/core/core.1864.6.cpgs.1195452213
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1196834481
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1197007273
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1197007371
    /common/log/taos-log-a/core/core.1864.6.cpgs.1197007413
    /common/log/taos-log-a/core/core.1952.11.ConfSchd.1198044080
    /common/log/taos-log-a/core/core.1843.6.gyromain.bin.1198044184
    /common/log/taos-log-a/core/core.1842.6.gyromain.bin.1199858530
    My understanding is these core files are crash dumps and are safe to delete?
    Jared

  • Meeting Place 7.1 Scheduling recurring voice conference issue

    Hello I am having an issue with Meeting Place 7.1, whenever we try to schedule a recurring voice conference we do not get the whole schedules that we need.
    For example If I try to schedule a conference daily for a month I don´t get schedule all the 30 days I get an error in some days.
    I have found this in the User Guide for Cisco Unified MeetingPlace thecnical documentation:
    • If the system is unable to schedule all meetings in your complete recurring meeting chain, it prompts
    you about the meetings it could not schedule. If this happens, set up individual instances of the
    meetings that could not be scheduled.
    But I am wondering if there is something that could fix this issue, becuase it happens every time we try to use the recurring option.
    Thanks in advance for your help.

    what does the Username for the dedicated email account for Cisco Unified MeetingPlace on the Microsoft Exchange Server indicate?
    Example: [email protected]  
    Does that means that email notifications sent by meeting place will be sent by the email address [email protected]?

  • Meeting place external calls

    Hi,
    We have configured meeting place with webex-node.
    When internal users join the meeting we can hear eachother.
    When an external user calls the ISDN number he hears all the messages from meeting place, he gives the meeting ID and after that he should hear the waiting room music, or be joined in an existing meeting, but he hears nothing.
    When a meeting of some internal users is place, we can hear that meeting place anounces that user XYZ joins the meeting. XYZ being the name that external user has given. But external user can not hear anything, and internal users can not hear external user. When external user hangs up, meeting place says that user XYZ has left the meeting.
    It seems that the stream of exteranl user is not mixed with the internal users.
    any idea?
    thanks,
    JH

    Something goes wrong between Meeting place/Callmanager/Voice gateway
    Voice gateway uses H323 to Callmanager
    Meetingplace uses SIP to Callmanager
    Solved problem by creating a SIP dial-peer on voice gateway pointing to MP
    JH

  • Meeting place server

    Hi All
    One of my customer is not beeing able to dial in to meeting more than 6 people, port allocated for the meeting was 20. Rest of the caller were getting disconnect tone.
    I looked at the logs and found this message but not sure why ?, does any one know what this means (See logs below)
    15315: Dec 17 2012 16:00:10.402 NZD: 192.168.125.4: %CS-6-EX_RAP_INSESSION: 0x200f7: 0/5,  "csapmain.cc", 1394 (0x2d, 0x2e9, 0x122, 0x69880000) All access ports blocked for 45 mins starting now
    15316: Dec 17 2012 16:00:10.402 NZD: 192.168.125.4: %VUI-4-OK: 0x0: 0/8,  "vuiconf.cc", 1890 (0x1, 0x25, 0x122, 0x89)
    15317: Dec 17 2012 16:00:11.992 NZD: 192.168.125.4: %CS-6-EX_SCHEDPARAMSCHANGEDBY: 0x200fc: 0/5,  "csschedparams.cc", 1146 (0, 0, 0, 0) Scheduling Parameter had just been changed by user 0
    15318: Dec 17 2012 16:00:12.292 NZD: 192.168.125.4: %CS-4-OK: 0x0: 0/5,  "csconfrec.cc", 13250 (0xfff, 0x1, 0x2, 0)
    15319: Dec 17 2012 16:00:22.257 NZD: 192.168.125.4: %VUI-4-EX_VUINOTQUITEREADY: 0x300d6: 0/8,  "vuisession.cc", 7621 (0, 0x6, 0, 0) VUI is not quite ready for new calls
    15320: Dec 17 2012 16:00:22.258 NZD: 192.168.125.4: %VUI-4-EX_MSGHANDLER: 0x1007d: 0/8,  "cmsnetwk.cc", 1718 (0x3, 0x25, 0x26, 0x3c8e) Error from message handler;, max=37, code=38, seq=0x3c8e
    15321: Dec 17 2012 16:00:22.258 NZD: 192.168.125.4: %VUI-4-OK: 0x0: 0/8,  "vuirouter.cc", 267 (0x2f9a0014, 0x2, 0x26, 0x3c8e)
    15322: Dec 17 2012 16:00:22.258 NZD: 192.168.125.4: %VUI-6-OK: 0x0: 0/8,  "vuirouter.cc", 268 (0x60b00013, 0x2, 0x3, 0)
    15323: Dec 17 2012 16:00:32.357 NZD: 192.168.125.4: %VUI-4-EX_VUINOTQUITEREADY: 0x300d6: 0/8,  "vuisession.cc", 7621 (0, 0x7, 0, 0) VUI is not quite ready for new calls
    15324: Dec 17 2012 16:00:32.358 NZD: 192.168.125.4: %VUI-4-EX_MSGHANDLER: 0x1007d: 0/8,  "cmsnetwk.cc", 1718 (0x3, 0x25, 0x26, 0x3c8e) Error from message handler;, max=37, code=38, seq=0x3c8e
    15325: Dec 17 2012 16:00:32.358 NZD: 192.168.125.4: %VUI-4-OK: 0x0: 0/8,  "vuirouter.cc", 267 (0x2f9a0014, 0x2, 0x26, 0x3c8e)
    15326: Dec 17 2012 16:00:32.358 NZD: 192.168.125.4: %VUI-6-OK: 0x0: 0/8,  "vuirouter.cc", 268 (0x60d00013, 0x2, 0x3, 0)
    15327: Dec 17 2012 16:00:32.631 NZD: 192.168.125.4: %VUI-4-EX_VUINOTQUITEREADY: 0x300d6: 0/8,  "vuisession.cc", 7621 (0, 0x8, 0, 0) VUI is not quite ready for new calls
    15328: Dec 17 2012 16:00:32.632 NZD: 192.168.125.4: %VUI-4-EX_MSGHANDLER: 0x1007d: 0/8,  "cmsnetwk.cc", 1718 (0x3, 0x25, 0x26, 0x3c8e) Error from message handler;, max=37, code=38, seq=0x3c8e
    15329: Dec 17 2012 16:00:32.632 NZD: 192.168.125.4: %VUI-4-OK: 0x0: 0/8,  "vuirouter.cc", 267 (0x2f9a0014, 0x2, 0x26, 0x3c8e)
    15330: Dec 17 2012 16:00:32.632 NZD: 192.168.125.4: %VUI-6-OK: 0x0: 0/8,  "vuirouter.cc", 268 (0x60f00013, 0x2, 0x3, 0)

    The following case was opened for this above question/problem:
    http://wwwin-tools.cisco.com/casekwery/getServiceRequest.do?id=624495099
    In summary,
    It appears that a maintenance window of 45 minutes was configured for the meeting place server
    at Dec 17 2012 16:00 NZD, and it blocked all further calls into the system.
    In Meeting place 8.0 scheduling a maintenance  windows will result in  system reserving
    all available access ports , resulting in  total unavailability  for new callers. However
    existing calls will be preserved.
    Please refer
    http://docwiki.cisco.com/wiki/Cisco_Unified_MeetingPlace_Release_8.0_--_Monitoring_and_Mai
    ntaining_the_Cisco_Unified_MeetingPlace_Web_Server#Scheduling_a_Maintenance_Window
    Once all the ports are reserved system will disallow all new callers from joining the
    meeting by giving error message 480, Temporarily in available
    Pramoth stated:
    Thanks for the finding. We didn't out the system under maintenance on that day.
    Where can I check to confirm if the system was put under Maintenance mode during that
    time.
    The Engineer went on further to say
    In meeting place 8.0 , while scheduling a meeting users can select an option called
    'reserve all ports'. Selecting this option will create a meeting, in your case 6988 that
    will block all access ports.
    You can right click on meeting 6988 --> Select Meeting details --> Check 'Meeting
    Type' and it will be 'reserve all ports'
    Access ports are virtual software ports by which audio callers access application server.
    When a person schedules a meeting and uses the option 'reserve all ports' ,system will
    reserve all system access ports for that meeting making meeting place  inaccessible for
    anyone else for calling in. Since users are unable to call in or schedule meeting this
    meeting will act as a maintenance window.
    0x122 is the Unique Meeting id corresponding to meeting id  6988. You can confirm it if
    you run 'mtginfo -m 6988' from you application server, it will display 0x122 as unique
    meeting id.
    just trying to provide some info to this question in case anyone runs across the same issue. they can see the notes/details that has been provided

  • Meeting Place and Webex Call Back Failing

    Hi
    Meeting place 8.5 with WebEx scheduling, SIP trunk to CUCM 8.5.
    Calling in using the specified number configured in call manager completes over the SIP trunk however call back from webex fails.
    Error:
    WebEx call back failed; no answer.
    Problem is I never recieve a call. I have enabled Webex call backs in webex.
    Seems like there is an issue on either MP or CUCM.
    Just looking for some ideas as I am stumped.

    This turned out to be a few things:
    1) I needed to configure a SIP proxy to CUCM from meeting place. This was the CUCM IP address and TCP port number.
    2) The SIP trunk security profile needed to be reconfigured for this trunk.
    3) E164 was being used so I created a translation pattern to strip the + for the CSS associated with the RP.
    A few things learned along the way.
    1) The "activity" command ran from a SSH prompt with allow you to simulate a call from meeting place. Option 4, enter the number to dial and "f" for port.
    2) In meeting place - Services -Logs - System Information Capture - Loading the index file and under the  CCA SIP LOG is the error being returned by CUCM. In my case it was Warning: 399 CSLCCM1 "Unable to find a device handler for the request received on port
    3) Command "cptrace" again from the SSH prompt will allow you to view the digits being sent from webex to meeting place.
    I hope this information helps someone...

  • Problem with Cisco Unified Meeting Place Express

            the user is unable to get connected to the Meeting Bridge set up in the Cisco Unified Meeting Place Express on the scheduled time.

    Hit up [email protected] and ask. They'll either say 'no' or give you hand; either way that's your answer.

  • Mapping Meeting place calls via DID Number

    I have a Meetinng Place (5.3) and it set up with a central DN. I'd like tot enable DIDs for each user so that they can just enter a PIN and be put into the appropriate meeting room. That way, I can just bill the 800 charges directly off the phone bill and not have to worry about Meeting Place billing.
    My vendor says that it can't be done - map a did to a particular "room" or profile. I can't imagine that that is the case.
    So - where do I start? I don't see any good install / admin info that pertains to this type of functionality.

    Something goes wrong between Meeting place/Callmanager/Voice gateway
    Voice gateway uses H323 to Callmanager
    Meetingplace uses SIP to Callmanager
    Solved problem by creating a SIP dial-peer on voice gateway pointing to MP
    JH

  • How to change host name and domain name in installed Cisco Meeting Place Express 2.0?

    Hi
    I have  Cisco Meeting Place Express 2.0 installed on server. Meting Place uses Linux (Red Hat) as base operation system. Please tell me how I can change host name and domain name for Meeting Place Express application to integrate it into corporate domain infrastructure.
    Thanks in advance!!!
    Sincerely yours
    Sergey Bondarenko

    Hi
    Thanks for your attention for my humble problem.
    I have performed Meeting Place Express configuration through the “net” command.
    But now unfortunately I can't connect to meeting place through web browser. I just get blank page.
    Though I can reach the server with help of ssh. I think my DNS works properly because I can resolve the ip address of  cumpxvoice .uclab.com and cumpxweb. uclab.com with help of dig command.
    Have you any idea?
    A lot of thanks in advance!!
    Sincerely yours Sergey Bondarenko
    Here I have printed the net configuration output of Cisco meeting Place Express:
    [root@cumpxvoice root]# net
    This is the MeetingPlace Express network configuration utility.
    Up to the point where you save changes, it is safe to hit ^C to get
    out at any time, in which case nothing will have changed.
    1) List current configuration
    2) Configure Ethernet port 1
    3) Configure Ethernet port 2
    4) Configure service bindings
    5) Set host names
    6) Set domain name
    7) Configure DNS service
    8) Configure NTP service
    9) Configure routing
    10) Done
    Select: 1
    Primary/audio host name: cumpxvoice
    HTTP host name:          cumpxvoice
    RTMP host name:          cumpxweb
    Domain name:             uclab.com
    Service bindings:
    Audio:                   port 1 (eth0)
    Web browsing (HTTP):     port 1 (eth0)
    Web conferencing (RTMP): port 2 (eth1)
    Port 1 (device eth0):
    IP Address:      10.62.60.116
    Network mask:    255.255.255.0
    Default gateway: 10.62.60.1
    Link setting:    autoneg on
    Port 2 (device eth1):
    IP Address:      10.62.60.117
    Network mask:    255.255.255.0
    Default gateway: 10.62.60.1
    Link setting:    autoneg on
    Static routes:
    Destination      Gateway          Network mask     Port
    0.0.0.0          10.62.60.1       0.0.0.0          1
    DNS Servers:
    10.62.60.115
    10.0.1.4

  • Time issue while scheduling meeting in meeting place 8.0

    Dear Team,
    I am very new to Meeting Place  system. Here we have version 8.0 and i am facing below issue.
    While scheduling meeting when i have mentioned start time as 13.30 and end after 30 min.
    but the issue is user can join the meeting before 13.30 and thats is security issue
    i would like to know how to restict this. my requiremnt is user can only join before 10 min.
    Regards
    Hari

    Hi Hari,
    Is you MeetingPlace 8.0 integrated with WebEx, or it is an Audio Only solution?
    If you are scheduling meetings in Audio Only solution, you can specify "Early meeting start (minutes)" variable in System Configuration > Meeting Configuration.
    If you have WebEx integration and WebEx scheduling, you would need to specify a default "Join before host", but every host would have to configure that for their own profile.
    -Dejan

  • Time issue iwhile scheduling meeting in meeting place 8.0

    Dear Team,
    I am very new to Meeting Place  system. Here we have version 8.0 and i am facing below issue.
    While scheduling meeting when i have mentioned start time as 13.30 and end after 30 min.
    but the issue is user can join the meeting before 13.30 and thats is security issue
    i would like to know how to restict this. my requiremnt is user can only join before 10 min.
    Please help

    Hi Hari,
    Is you MeetingPlace 8.0 integrated with WebEx, or it is an Audio Only solution?
    If you are scheduling meetings in Audio Only solution, you can specify "Early meeting start (minutes)" variable in System Configuration > Meeting Configuration.
    If you have WebEx integration and WebEx scheduling, you would need to specify a default "Join before host", but every host would have to configure that for their own profile.
    -Dejan

  • Meeting Place 8.0 Audio Recording play back

    Hi,
    We are currently using Meeting place 8.5, it is currently installed as Express Media server (Single server solution) as audio only conferencing solution.
    I am able to record a meeting using meetingplace conference manager, but there is no option to find/play the recording, when i select the meeting and check the meeting details, I can find that the meeting is recorded but Attachment is displayed as No.
    I found links which says to find the meeting using Meeting place web scheduler and find meetings but is if no avail as there is not web server installed in my setup.
    Would like to if there is any way to find/play the recording.
    Thanks,
    Vinay

    Hi Vinay,
    Accessing or playback of recordings requires a Web Scheduling server to manage and convert the recording from the Application server. This is not possible with just an applicaiton server alone.
    Thanks,
    Derek Johnson
    Conferencing TAC

  • Need Urgent Help on Meeting Place Integration with CUCM 7.1 and AS5400 PSTN Gateway

    Hi,
    This is first time I am on this forum.
    I have already tried going through a lot of docs on docwiki.cisco.com but couldn't find complete configuration help.
    I have to integrate Meeting Place 8.X with an existing CUCM and an E1 gateway (PSTN Gateway) AS5400.
    The CUCM is already part of a Telepresence Environment. I need to create a SIP trunk between AS5400 and CUCM 7.1 and then create a Trunk between AS5400 and Cisco Unified MP 8.X and then between CUMP and CUCM.
    I need help on AS5400 SIP Configs as well as parameters I need to cover on CUCM (Though I have done some basic dial-peer configs but they haven't been of much help).
    Then I also need help on AS5400 SIP configs with CUMP 8.0
    Any docs on Integration between CUMP and TP3000 will be of great help too.
    Rgds,
    Asim

    I can get the Ricoh to register as sip endpoint, it answeres then imediatly disconnects. Doing a monitor with Wireshark looks like it attempts to negotiate t38 but fails. Any idea why this fails?
    |160.260684000|         INVITE SDP (g711U)            |                   |SIP From:
    |         |(5060)   ------------------>  (5060)   |                   |
    |160.338806000|         INVITE SDP (t38)              |                   |SIP Request
    |         |(5060)   <------------------  (63435)  |                   |
    |160.339545000|         491 Request Pending           |                   |SIP Status
    |         |(5060)   ------------------>  (5060)   |                   |
    |160.547894000|         406 Not Acceptable            |                   |SIP Status
    |         |(5060)   <------------------  (63435)  |                   |

Maybe you are looking for

  • Zen Mozaic 8GB, the same Album Art shows up on every f

    My Zen Mozaic froze last Sunday but I brought it back to life using that wonderful reset button (or whatever it's called). It works as it should except for one thing - every single music file appears to belong to the same album. This might not have b

  • Computer not fully starting up

    I have a PowerMac G5, and just recently my computer will start up to the gray screen, yet it will remain there, and usually around 30 seconds later, my fans start blowing like crazy. I have shut off my computer and rebooted it with several different

  • Solaris 8 (Intel) install - graphics adaptor

    This product seems to operate with a limited range of graphics cards. I have a TX Pro motherboard with an SIS 6326 AGP graphics chip, and 8 Mbytes of on-board VGA memory. I can't install Solaris unless I can configure the display adaptor correctly, a

  • Twitter widget dead?

    My iWeb Twitter widget has gone dead and when I paste the code for Twitter's official widget, nothing shows up in iWeb beside "Tweets by myusername".  I have searched the forum but nothing has worked to solve this issue.  Does anyone have code for a

  • TS5168 some of my pictures say that the necessary data reference could not be resolved. help

    some of my pictures say that the necessary data reference could not be resolved. help