Unable to make recovery disk-Error code:02012​3

I just recently bought Satellite P755-S5265  and I am having trouble creating recovery discs. 
When using the Recovery Media Creator program, I can create Discs 1 to 3, but am having trouble on disc 4.
About halfway during the downloading sequence this error pops up:
Failure to open file 
D:\DATA.INI
(Error Code:020123-F1-0000000) 
I have gone through several DVD-R discs each having the same error.
I've also tried using the Hard Disk Recovery utility to restore the computer to manufactory settings, but the same error pops up again. 
Could someone please help me out?
I appreciate an help I can get.
Thank you in advance  

If you're getting the error both when creating recovery media and when recovering the computer using the recovery partition, it sounds like there's a problem with the data on the recovery partition itself.
I'd contact support at (800) 457-7777.
- Peter

Similar Messages

  • Unable to make recovery disk-Error code:020123-f10000000

    Hi guys 
    please help if can?, i purchased the recovery disc for my tosibia qosmio dx730 -10p loaded new windows on all perfect and tried to make a copy of the back up media so i have extra copy incase other  gets damaged its saying same thing when purchased this pc from new ,on first  blank dvd r disc it gets half way and saids ,
    Failed  to open file
    E;\boot\BCD
    ERROR CODE 020123-F10000000
    E drive is my dvd rw drive 
    i have intalled the new discs they sent me and still cant make a media back up .
    Deborah 
    Solved!
    Go to Solution.

    Hi ! Iuse memorex DVD-R. What I would do is buy a usb and create your recovery on it. That is if your machine will boot to a USB. I have a 16GB USB with my recovery on it. It would be a lot easier to use it than all those discs You can check boot sequence to see if your machine will boot from USB
    I Love my Satellite L775D-S7222 Laptop. Some days you're the windshield, Some days you're the bug. The Computer world is crazy. If you have answers to computer problems, pass them forward.

  • Unable to make recovery disk on in pavellion g62016 .dat file is missing in recovery drive

    unable to make recovery disk on in pavellion g62016 .dat file is missing in recovery drive
    can i use the .dat file of another same notebook
    what is significance of ,dat file

    Hello shail11. I understand that you're having some problems creating a recovery disc. Is this correct?
    You can not use another .dat file.  The recovery media is specific to a certain notebook, so using another computer's files will not work.   If you're running into issues making a recovery media you could attempt to perform the recovery from the BIOS. Here is a document which outlines the process.  ALL data not backed up before performing the recovery will be lost.
    Let me know if this helps; have a great weekend!
    Please click the white star under my name to give me Kudos as a way to say "Thanks!"
    Click the "Accept as Solution" button if I resolve your issue.

  • HP G62-357CA Recovery Disk Error code OxeOef000e

    I am trying to recover my HP notebook G62-357 and when I am on the second disk it is giving me the following error. Can anybody please help.
    "Recovery Manager could not restore your computer using the factory image. Please contact HP Support.
    Error code : OxeOef000"
    I am using Windwos 7 operting system, and these recovery disk are the original ones came with the system, were never opened or used, so I do not think any issue with the CDs itself.
    Just so you know I am out of the warranty, so can't call HP. Any help is appreciated.
    Thanks
    This question was solved.
    View Solution.

    Anytime!

  • Pavilion dv7-5003tx replace hdd recovery disks error code OxeOefoooe please help.

    have tried both recoveries hangs at 45% and goes no where

    Hi,
    One factor that can cause this error is replacing the original HDD with a drive of smaller capacity - if this is the case, recovery discs almost always fail to work correctly, however there isAssuming this is an alternative option you could try.
    Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
    An example of a COA Label can be seen Here.
    You can create a Windows 7 installation disc yourself using another PC - just download the correct Disc Image ( this must be the same version that originally came with your notebook ) from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here.  These Images are clean and from a well-respected source, however there are only limited versions available.
    Windows-7 sp1-iso-official-32-bit-and-64-bit
    Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
    http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
    Any additional drivers and software you may need can be found Here.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • OraRRP Error with "Unable to copy data file;Error code 2, check disk space"

    Hi,
    Some users get this message -"Unable to copy data file;Error code 2, check disk space" when run report with orarrp, but most users do not get it.
    I check free space at both server and client side, they are very sufficient.
    I also checked directory exists for REPORTXX_TMP variable.
    My user call reports via URL (rwservlet) and it occur for all reports.
    How I can solve this problem?
    Thanks in advance.
    Tawatchai R.

    Hi,
    have the same problem now. One user has temporarily problems to download .rrpa files via URL (rwservlet) request. Error code: -"Unable to copy data file;Error code 2, check disk space". Did you get a solution??
    Thanks in advance. Axel

  • Unable to create recovery disk using media creation on hp pavilion g6 2236tx

    i am attempting to make recovery disk of my notebook through hp media creation i am using DVD disks for the same but the problem is that when the processing bar reaches almost 99percent it shows error message that unable to create recovery disk try again later!
    please help!

    Hi saksham_jain,
    Welcome to the HP Forums!
    I would like to take a moment and thank you for using the forum, it is a great place to find answers. For you to have the best experience in the HP forum, I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
    I understand that you tried to create your recovery DVDs using HP Media Creation and it failed. Here is  a document to assist you with creating the recovery DVDS. Creating Recovery Discs or Saving a Recovery Image to a USB Flash Drive (Windows 7). 
    If this should fail for any reason, please provide the error and any other details.
    Sparkles1
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

  • Phone stuck in recovery mode error code 40 and would not restore

    My Iphone 3GS stuck in recovery mode error code 40 and would not restore.I was with AT & T.Please help!

    Hi there...
    Actually I was stuck with this situation yesterday. Here is what I did to overcome this issue: I hope it helps.
    To start with, here are few things to you should make sure of:
    1- You have the latest version of iTunes. You may try to uninstall and reinstall iTunes.
    2-Restart your Windows.
    If still no luck, try editing the Hosts file, here is how;
    1- click on RUN then copy and paste the following:
    notepad c:\windows\system32\drivers\etc\hosts 
    2- look for gs.apple.com
    3- if there are numbers infront of it just delete them or just type # before the numbers.
    4- Save the file and try restoring again.
    Note: you should have administror access to edit the Hostes file.
             put your iphone in DFU mode before restoring.
    I hope this helps. It did for me

  • Unable to install creative cloud error code 1

    unable to install creative cloud error code 1
    windows 8

    Refer below link
    Error "Failed to Install" Creative Cloud Desktop application

  • HP Pavilion dv6 Notebook PC unable to boot recovery disk

    HP Pavilion dv6 Notebook PC unable to boot recovery disk.  First when I power on my notebook it goes straight to the launch recovery or launch Windows normally screen.  When I choose start windows normally, it goes to the window screen and freeze.  When I try to launch the start-up with windows 7 start-up disk, the computer will not load the files.  When I tried to complete a hard drive test, it failed with a failure ID 9UXNXA-55E65V-XD003G-60XR03.  
    I'm looking for a solution, can someone help?

    Hi:
    It sounds like you need to purchase a new hard drive for your notebook, and reinstall the operating system with your recovery disks.
    When a HDD fails a diagnostic test, it normally means it is done for.
    Paul

  • Hp pavillion a000 recovery disk error.. where to go from here?

    HI.. .fIRST Thank you so much for being here today...
    I have an HP pavillion a000 which was bought used.
    About a week ago I got pre-windows msgs. on the 3rd time it has frozen at this point
    Msg as follows...
    bla bla.. but windows did not start successfully..
    a recent hardwared or software change may have caused this..
    It has counted down and started in normal mode..
    then it has frozen.. and I have tried to start it it all modes..
    This last attempt actually started windows and went back to this screen
    I put in the compaq recovery disk...  I get red screen saying recovery disk error..
    PLEASE Contact support
    I have un plugged..re plugged and we go in circles...
    I'm not sure where to go from here but any suggestions would be VERY appreciated as I do have some artwork I was doing stuck in computer now..
    Do you think it's a software,, hardware or  even a virus thing??
    Additional info... Hp pavillion a000   system no.174A-ABA.   hw bom 8121110   sw bom NA 40
    serial no.  mxk34916m
    operating system.. Windows xp... yes I tried recovery disks I have..  puter says...non compatible..
     I use firefox as browser via century link dsl..
    I can pull the hard drive and I have a harness for accessing the hard drive directly via usb download if you think that's an option but not letting me into windows even has me doubtful that would work;;;
    So as I mentioned.. ANY sugestions you can offer as what to try next would be MOST welcome!
    I can replace the computer easy enough but I would love to be ables to rescue my art in progress at least!

    Hello ValeryWildflowr,
    If the computer was working fine before you might just want to try a system restore. This should correct the problem without affecting any of your files.
    Here is a link for a system restore.
    Let me know if this helps.

  • Novell eDirectory Target Recon: Unable to search LDAP LDAP: error code 53

    Hi All,
    I am getting following error while running the Novell eDirectory Target Reconciliation in batch mode:
    *ERROR,27 Oct 2009 22:59:54,263,[XL_INTG.EDIRECTORY],Paged Search failed.javax.naming.OperationNotSupportedException: [LDAP: error code 53 - Unwilling To Perform]; remaining name 'ou=centrica,ou=Regular,o=Infosys'*
    *DEBUG,27 Oct 2009 22:59:54,263,[XL_INTG.EDIRECTORY],tcUtilLDAPOperations -> ~~~~~~~~~~Entering disconnectFromLDAP()~~~~~~~~~~*
    *DEBUG,27 Oct 2009 22:59:54,263,[XL_INTG.EDIRECTORY],tcUtilLDAPOperations -> Closing initial directory context*
    *DEBUG,27 Oct 2009 22:59:54,263,[XL_INTG.EDIRECTORY],tcUtilLDAPOperations -> ~~~~~~~~~~Leaving disconnectFromLDAP()~~~~~~~~~~*
    *ERROR,27 Oct 2009 22:59:54,263,[XL_INTG.EDIRECTORY],tcTskLDAPUserReconciliation] --> execute(): failed. Exception in execute() method.*
    *javax.naming.NamingException: tcUtilLDAPOperations  -> : NamingException : Unable to search LDAP [[LDAP: error code 53 - Unwilling To Perform]]*
    *     at com.thortech.xl.integration.ldap.util.tcUtilLDAPOperations.search(Unknown Source)*
    *     at com.thortech.xl.util.schedule.tasks.tcTskLDAPUserReconciliation.processChange(tcTskLDAPUserReconciliation.java:2752)*
    *     at com.thortech.xl.util.schedule.tasks.tcTskLDAPUserReconciliation.execute(tcTskLDAPUserReconciliation.java:344)*
    *     at com.thortech.xl.scheduler.tasks.SchedulerBaseTask.run(Unknown Source)*
    *     at com.thortech.xl.scheduler.core.quartz.QuartzWrapper$TaskExecutionAction.run(Unknown Source)*
    *     at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)*
    *     at weblogic.security.service.SecurityManager.runAs(Unknown Source)*
    *     at weblogic.security.Security.runAs(Security.java:41)*
    *     at Thor.API.Security.LoginHandler.weblogicLoginSession.runAs(Unknown Source)*
    *     at com.thortech.xl.scheduler.core.quartz.QuartzWrapper.execute(Unknown Source)*
    *     at org.quartz.core.JobRunShell.run(JobRunShell.java:178)*
    *     at org.quartz.simpl.SimpleThreadPool$WorkerThread.run(SimpleThreadPool.java:477)*
    *DEBUG,27 Oct 2009 22:59:54,264,[XL_INTG.EDIRECTORY],tcTskLDAPUserReconciliation] --> execute(): exit*
    This error is coming only for OU's which have more than 200 entries in them. The
    if anyone has any clue on this problem, then kindly help.
    Cheers,
    Sunny

    See if your e-directory supports paged searches.
    If not then you have to configure your e-directory to support paged searches. I think the connector by default only uses paged searches.
    You need to look for OID 1.2.840.113556.1.4.319 (page control) in supported control list of the rootDSE.
    Hope this helps,
    Sagar

  • Cause of "unable to write to disk error"

    Using a epson perfection v100 scanner and keep getting an unable to write to disk error after it  scan and will not copy.   Any ideas about what to try to fix this? thank you..
    p.s. using snow leopard and I have already tried to re-dowload software off the epson site.

    Have you tried...
    Trashing preferences?
    Run Disk Utility?
    Instead of control-clicking on the drive, try control-clicking on the Capture Scratch folder and the project Subfolder and changing permissions.

  • What does this mean? Server Message: Unable to load server - system error code: 0x80080005, CO_E_SERVER_EXEC_FAILURE: Server execution failed.

    This is the error that we get when we run the Tag File.
    ERROR 04/16/2004 02:26:15 PM Server ERROR from Server: National Instruments.OPCLookoutDrivers. Status: -196608, Server Message: Unable to load server - system error code: 0x80080005, CO_E_SERVER_EXEC_FAILURE: Server execution failed.
    What does it all mean?

    ACRE,
    this looks like the Industrial Automation OPC Server (Lookout OPC) is not correctly installed or configured and therefore the DSC Tag Engine - as OPC client - cannot launch the OPC server correctly.
    Two checks I have in mind.
    - Installation check: Check if the Industrial Automation Server is installed and configured correctly and that you will have a .lpd file as default. Could it be that the .lpd file is corrupted? BTW - what kind of protocol are you using and did you configure aliases for the LPD object? A good resource on checking the configuration might be the online help of Industrial Automation Server (Lookout Protocol Drivers) or the link penDocument>How Do I Configure My Devices with Lookout Protocol Drivers?
    - Access rights, COM/DCOM problems: Can you launch the OPC Server with another OPC client? Is your OPC server running locally? If you don't know how to check on this I found a good KB Tools for Troubleshooting OPC Interface Problems E.g. can you access it with Server Explorer?
    Last question... did you encounter this problem recently while it was working before? What changes have been done on your system?
    Let us know if you have some questions and I hope some of the links help you further troubleshooting this issue.
    Roland

  • Recovery disc error code: 0xe0ef000e

    Back in December I started getting warning messages about my SMART Drive failing and was told to create recovery disks for my Pavilion dv-7 Notebook, which I did. A few weeks ago the hard drive crashed and I replaced it. When I went to recovery page my disks did not work and I received the following error code: 0xe0ef000e. I looked on HP support website and saw where I could order new recovery disks which I attempted to do and they are not available. So I have a 2 year old $1000 laptop for which I just bought a new $100 hard drive and it's unuseable. Any suggestions on what to do next?

    Hi,
    There are a couple of options.
    1.  You could try the reliable 3rd party reseller Here.
    2.  Here's an alternative ( and cost free ) option you could try.
    Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
    An example of a COA Label can be seen Here.
    You can create a Windows 7 installation disc yourself using another PC - just download the correct Disc Image ( this must be the same version that originally came with your notebook ) from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here.  These Images are clean and from a well-respected source, however there are only limited versions available.
    Windows 7 Images.
    Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
    http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
    Any additional drivers and software you may need can be found by entering either your Model No. or Product No. Here.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

Maybe you are looking for