Unable to output from FCP to Canon XL1.

I have an eMac with Final Cut Pro 4.5 HD. I also have a Canon XL1 3 CCD camcorder.
I have no problem capturing footage from my camcorder to my eMac on FCP. I can also connect my Canon to my VCR and record off my camcorder to my TV, as well as play the tape on my camcorder to watch it on TV.
However, I cannot output from FCP to my camcorder. The 4 to 6 FireWire is attached to both the camera and the eMac and I checked the Log and Capture feature and FCP does recognize a camera or deck is attached. I've been trying to output it using manual record in which I press record on my camcorder and play the playhead on FCP. As I record, there is no picture on my viewfinder, nor any audio being recorded and when I play it back, I just get this blank blue screen, but the timecode is recorded.
Am I missing something here?

ensure the following are set
View>Video Playback>Firewire Apple 720x480 (NTSC or PAL - whatever is appropriate)
View>Audio Playback>Audio follows video
View>External Video>All Frames
If this isn't what you are set to do, you won't be sending video out to your recorder.
x

Similar Messages

This new 1080p tv sets and my 1080i Sony camera-output from FCP

I use a Sony FX1. My best capture is at 1080i or 720p.
I've recently been recording at a higher shutter speed and am getting improved footage.
I note that FCP has an output option of 1080p - 30. Is this only half as good as the new monitors can show? If I eventually want to create highest quality for playback on 1080p-60 will I need an updated camera and will FCP have to offer 1080p-60?
Since I've never viewed 1080p-60 is the - 30 vs - 60 a big issue?
Using the 1080p-30 makes for a much improved view than H264 720x480 or HDV 1080i any other settings up to this one. H264 is a GREAT file size saver but does not use near the bit rate of 1080p-30.
One other thing. When the new OS comes out with 64-bit processing, is FCP and DVDPro already ready. I have not found any specs on FCP 5.1.4 indicating it is 64-bit ready.

ensure the following are set
View>Video Playback>Firewire Apple 720x480 (NTSC or PAL - whatever is appropriate)
View>Audio Playback>Audio follows video
View>External Video>All Frames
If this isn't what you are set to do, you won't be sending video out to your recorder.
x

Help Recording from FCP to Canon XHA1 Mini DV

Hi there. I am totally new to this forum, but I am desperate.
I shot on a XHA1 camera, captured and edited on FCP and for some reason, cannot, absolutely cannot figure out how to record it (for backup) on to the camera I shot it with. (miniHD tape) It was shot hi def, widescreen format. 1080i 60.
I have tried so many different settings, both with the camera, and FCP that I am totally confused.
I never had this problem with my GL1 that I used for years....
Please please please, any help?
Alanna

Which version of Final Cut Pro were/are you using to capture the footage from the XH A1 to your computer?

Output from fcp to dvd studio 4 sd get bad quality dvd pixelized

2 hour video 740 x output. tape out looks great looks great but dvd does not. pixalized could not see faces clearly. please suggest
bit rate one pass or two. on reg. 4.7 dvd-r.
will use ac3.

Hi:
You can use Bitrate Calculator to check the max bitrate. If you use AC3 192 kbps, for 2 hs you can use 486 kbits/s for your video.
If you want to use a higher bitrate, you must split it in two 4.7 discs or a DL DVD.
Hope that helps !
Alberto

Problems outputing audio from FCP into a mini dv

hi there
i'm trying to output a video with 2 diferrent audio channels into a minin dv through a camera. everything is fine during output but when i check the tape the audio skips and sometimes sounds a little bit squeaking. i exported everything as .mov and imported back into FCP. so im outputting everything already rendered.
does any one have an idea why this is happening?
thank you.

Could definitely be a problem with the camera, but... the most obvious thing is that your output from fcp doesn't match the format on the camera. Make sure that both are set to 48k 16 bit and that your camera is recording SP.

Best Output for DVD from FCP???

I'm a newbie and need help. I was outputting from FCP 6.0.4 using Export > QuickTime Movie, then importing that file into DVD Studio Pro. But, a college student who saw it recommended Exporting using Compressor 3.0.3 which I did using the DVD: Best Quality 90 Minutes. I noticed an improvement in my DVD quality, however, in every program I've tried and retried so far I get a little short segment (about a 10 second portion) in my half hour long program that all of the sudden goes crazy with distortion and pixelization and image irratic jumping movements. What can I do to create a totally smooth video when going from FCP to Compressor or is there a better way to finally get it into DVD Studio Pro? I want the highest quality solution as the video footage is originally HD. Thanks for your help, Desperate Russ

coyotegyrl333 wrote:
For some reason, I've always found this to work:
render your project and make sure you have only one
video track in the timeline. Drag existing sequences into
a new one so that you accomplish this. Render.
Restart the computer.
Export using compressor.
Maybe this is mumbo-jumbo, but it works every time for me.
good luck to you.
The advice is more or less sound but you have several unnecessary steps. Your idea is to consolidate all of the FCP timelines and their associated media into a single timeline; you are nesting the project.
Forcing everything to render is good.
Export the entire project as a self contained movie.
Import the self contained movie into DVDSP.
You would perform these steps with each of the individual movie clips you want to have as menu items in your DVD project. Maybe. You might be able to use one single large movie and set go-tos for each chapter. Whatever.
But there is no reason to restart your computer.
And there may be no good reason to use Compressor to create the MPEG2 files.
bogiesan

Aspect Ratio HDV clip from FCP to After Effects

Can someone help me with exporting from FCP an HDV clip to After Effects? What I am doing is trying to export an HDV clip from FCP to AE but when I import it into AE the aspect ratio is all off. I have an HDV 1080i50 easy setup timeline and I am exporting from that as a quicktime movie (not conversion) with the current settings. When I bring that into AE I have a HDV comp set up and I drop the FCP movie into that comp. My FCP movie is 1920 X 1080 and is bigger thant the AE HDV Comp. Why? Shouldn't the sizes be the same since they are HDV? Please help
Tim

HDV is 1440 x 1080 native so if you have output from FCP that is 1920 x 1080 it is being misinterpreted by AFX.
Try creating a new comp in AFX using the HDV easy setup but set the frame size to 1920 x 1080 manually and see what that does.

Exporting Stereo from FCP

Hi all,
I'm currently struggling with the output of a music video for broadcast. I am ultimately looking to create an MPEG IMX PAL quicktime.
I am running FCP 7.0.2.
The problem I am having is that every time I output from FCP my stereo sound (which I can see has very slightly different waveforms on each channel) is being turned into two mono channels.
My export settings are always stereo in the quicktime dialogue box and I have also tried the sequence being set to "channel grouped" and "stereo downmix" before export with no joy. I have also made sure that "downmix" is not selected in the audio mixer.
This is slightly frustrating as I've never had this problem before and I'm hoing it's something simple I'm overlooking.
Any help would be greatly appreciated.
Thanks in advance
Alex

Thanks David, that seems to be what the problem was. I thought it might be something simple I was over looking.
Just to check for the future, does this always have to be the case for a track to be exported as stereo from FCP and there is no way of overriding it in the export?
I'm guessing that it is, but for my sanity I thought I'd best check.
Thanks for your help
Alex

FCP 7.0.3 and Canon XL1s

I have just purchased a Canon XL1s and am having huge problems capturing footage of a decent quality using FCP 7.0.3
Having done some searching about the Canon camera and FCP i used, from the 'Easy Setup' menu
Format: PAL
Use: DV-Pal FireWire Basic
When i have captured the footage from the camera it is grainy and looks like it has been recorded from a very substandard device. I have tried a huge combination of settings all to no avail.
On the camera it was set to:
Movie Mode normal
16:9 was enabled
audio 12 bit ST-1 (but the audio sounds good no matter what settings i use to capture)
I have also tried capturing using iMovie and get the same results.
I am using Sony DV premium 60minute MiniDV tapes (both tapes have been brand new)
Any advice would be helpful

The camera definitely recorded in SP, that icon was visible on the viewfinder...
What settings should i be using in FCP to capture the video? From attempted research i found most comments suggesting to use a basic Firewire settings. i have used this in PAL format but the results are poor.
One thing I am confused about is the 32khz or 48khz settings. Which should i be using? I have an older version of FCE 4 where there are many settings for both 32khz and 48khz for DV FireWire but in FCP7 there are only options for 48khz.
Any advice would be welcomed at the moment.
I am also willing to upload clips of what I have to demonstrate visually the poor quality video I am capturing from the Canon

I need to output a PAL HDV project from FCP as a PAL DV file with 4 audio t

I need to output a PAL HDV project from FCP as a PAL DV file with 4 audio tracks - specifically one stereo pair to be t1&t3, the other stereo pair to be t2&t4. This is the standard way requested by an international distributor of tv programmes. I understand how to set the sequence in FCP to output 4 audio tracks - either 2 stereo pairs (1&2, + 3&4), or 4 discrete tracks. But how do I then output this as a QT file?
The manual tells me that to export multiple audio tracks, File>Export>QT Movie has it's Config pop-up menu in the Audio Settings area of the General tab of the Sequence Settings. Well, that's set for 4 discrete channels, but the QT export settings only allow for 2 mono or 1 stereo output, and that's what I get when I try it. What it says in the manual just doesn't happen.
Exporting via Compressor, on the other hand, has an abundance of choices of 4-track outputs, none of which are labelled as anything resembling 'discrete'. Would any of those 4.0 settings suffice? Or am I likely to get myself into difficulties further down the line? As I am monitoring for this task on a 2-track audio system, I cannot confirm exactly what I am getting when I use any of those settings.
Any advice would be greatly appreciated!
John

Call me naive, but I've not heard of splitting the stereo pairs like this before.
What broadcaster? (perhaps one of our EU regulars will drop in...)
You can do all sorts of pairing but it is coincident tracks pairing- eg 1/2 + 3/4
Sorry I can't offer anything.
x

Wanto output video from FCP to tv-monitor..

I've been searching for an answere in this forum aswell as PD150 forums..
Please help, I think of myself as a logical person but just can't figure this one out.
I try to output the video signal from FCP to a tv-monitor usin a Sony PD150 in the middle.
That is; Firewire from my G4 into my camera, s-video to scart into my monitor.
I've been fiddeling with the camera settigs but found nothing that indicates signal in/out or likewise.
I know that this isn't a PD150 forum but i thought I could find someone experienced here.
Thanks for answeres in advanced, Erik

#8 External Monitor Viewing.
Shane's Stock Answer #8:
A simple path is mac > firewire > camera or deck > rca cables > tv
Then start up your camera and tv, then open fcp.
Then go View > External video > all frames
Video playback should be Apple firewire NTSC (If you are using an NTSC set)
Audio playback should be Audio follows Video
Techinially, this should send synched video to your TV
If for some reason you can't view your timeline on your external monitor, there are a few things to try:
1) Make sure that the camera/deck is connected and powered on BEFORE you open FCP.
2) In the Final Cut Pro menu select AUDIO/VIDEO Preferences and make sure your signal is being sent out thru Firewire DV.
3) Go to the menu and select VIEW>EXTERNAL>ALL FRAMES.
4) Click in the % box above the image and select FIT TO WINDOW.
5) Go to VIEW->refresh A/V devices
6) Make sure the Log & Capture window is closed
If you want it to play in both the canvas and the external monitor you need to go to the FINAL CUT PRO menu and select AUDIO/VIDIO settings and make sure MIRROR ON DESKTOP is selected under the PLAYBACK OUTPUT section
Shane

FCE: Capturing footage from my Canon XL1

Got FCE and when capturing footage from my Canon XL1 I get the video however there is no audio!
Tried capturing footage via iMovies and works no problem!
Not sure if this has anything to do with it but I'm using a external mic. on my XL1 into one ch. on the audio inputs. Also scratch disks is on a external 1TB WD drive. Finally tried virtually all the set-ups on the 'easy set-up' but still no joy.
Can anyone throw me a life line on this one?!

sorry I should have made myself abit clearer.....when the tape is played back in my XL1 I can hear audio when my headphones are pluged into the camera also the camera has audio monitors which I can see movement verifying there is audio. However in FCE I don't see any audio level movement.
In terms of equip. I just have a external WD 1TB drive (USB), firewire cable for video camera and the USB cable for the keyboard & mouse.
Additional application: Flip video s/w (however had fce issue prior to installing this).

FCP 2 doesn't recognize Canon XL1s

Hello. I have Final Cut Express 2.0.3 installed on an iMac G5 10.4.5. FCP will not recognize my Canon XL1s. Not a faulty cable - I've tried two, one brand new. I've tried various Easy Set ups modes. Tried rebooting with all devices unlugged, etc. Nuthin'. If anyone knows of a solution I would appreciate the help. Thanks.
iMac G5 Mac OS X (10.4.5) 20"

1. Does the camera work when you use iMovie?
If so, you may have a funky Quicktime installation. Do the full Quicktime reinstall. (see below for directions)
2. Does the camera work if you have no external hard drive in the firewire chain?
If so, you have the classic 'Canon collision' on the firewire bus. The usual solution is to add a second firewire bus using an add-in PCI card (for desktops) or a PCMCIA card for Powerbooks. Unfortunetly, your computer does not allow either of these options - so your options are:
a) capture to the system hard drive, unplug the camera, reattach the external drive and move the material over.
b) try capturing using a different camera that plays better with external hard drives.
Good luck.
x
To do a full quicktime reinstall.
Go to /library/receipts and delete any files that say Quicktime followed by a number e.g. Quicktime703.pkg
Go to the Apple quicktime site and download the appropriate version of Quicktime to your hard drive.
Run the Quicktime installer.
Repair Disk Permissions for your System Disk (Disk Utility > Select the system disk > Repair Disk Permissions)
Reboot

TS3850 how to import a video from a tape recorder the brand is Canon XL1 mini DV into Final Cut or iMovie?

how to imort a video from a tape recorder the brand is canon XL1. i use firewire 6ping befort but the new Mac have not 6ping, they have 9ping

This is what you need:
http://rocketfish-prod-live.teletech.com/products/computer-accessories/RF-AP309. html

Unable to view output from concurrent manager

Hello all,
I am unable to view output from concurrent manager, I am using IE 8 32bit on Windows 7 & adobe 10.0.1
It gives a blank page
We are trying to view an xml report
EBS 11.5.10.2
db : 10.2.0.
linux 4 update 5
I have already reffered below documents but for no luck
Note: 888932.1 - R12.1 Unable To View Output For Xml Outputs - View Output Button - The window opens up And Disappear Automatically
Note: 305850.1 - Unable To View Output Of PDF Report When Clicking ''View Output''
Thanks.

Is the issue with XML/PDF concurrent requests or with all requests?
Can you find any errors in Apache/Database log files?
Is the application listener up and running? Can you find any errors in the listener log file?
Have you tried to run AutoConfig and bounce the services and see if this helps?
Thanks,
Hussein

Unable to output from FCP to Canon XL1.

Similar Messages

Maybe you are looking for