Unable to ping to the internet

if you do an nslookup then a server 8.8.8.8 what do you see?

Hey guys,
I have a weird issue. I am unable to ping out from the LAN. Pinging 8.8.8.8 goes nowhere and other sites as well.
SonicWall shows all internal to external services are allowed.
Internally everything is pingable.
I am also unable to ping from within the SonicWall Diagnostics tool. It just says IP address not responding.
NSA3500.
This topic first appeared in the Spiceworks Community

Similar Messages

WVC80N - Internet Gateway UPnP discovery failure message \ unable to view over the internet

I have the WVC80N. I recently got the new Comcast modem \ wifi but the Wifi is junk and had a lot of problems (loss connection, range etc) so I had Comcast "bridge" it so I just use my old wifi (LinkSys E1200). I have TZO to handle remote viewing. Everything was working great for about two weeks and we had a power outage. Since then, I have been getting UPnP discovery message (in the status tab of the WVC80N camera site) and I am unable to view over the internet. I get a 502 error usually but today I got extra info: "The socket connection to www.dfgehring.mylinksyscam.com failed.
ErrorCode: 10060. A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond."
I had Comcast do a "repair / reset" transmission to the modem and still get the problem.
I found these step on the forum:
1. Home Wirless Rounter administration page, find the UnPn settings and Turn off UnPn and save it. Wait for atleast 30 sec and go the same page and Turn it back on.
2. On your wireless camera Adminstraion page, go to "Options" and find the UnPn if it is already disabled go ahead and "enable" it also "enable" the "Alternate web connection" and save it. If it was already enable please disable it save the settings and enable back on.
The above 2 steps resolved my issue and I could able to view my camera from outside of my home network.
Still no luck. Tried it several times.
Could the power outage reset something on the modem or router to change this?
Thanks
Darren

That's what I thought. The power outage may have set the modem, router or camera settings back to factory defaults causing it to loose connection. First thing first, call comcast and check if the modem is still on bridge mode. The modem may have been set back to a modem/router mode due to power outage.
You may test if the remote access is properly set up in the network by going to http://ping.eu. In that site, you will see your internet ip address, take note of that. Click on port check, enter your internet ip address and the port number you used in the alternate web access port then click Go. If it says closed, there something wrong in the settings of either the router or camera. In that case, I suggest you reset the router and camera and then reconfigure them.
I found these articles online which could help you reconfigure your router and camera settings:
How to set up your router
How to set up router wireless setting
Connecting camera to wireless network
How to set up remote access on linksys camera
How to set up TZO on the linksys camera
Hope these helps.

Curve 9380 unable to connect to the internet via wifi

I'm using curve 9380 and unable to connect to the internet via my home wifi, there is no blackberry logo beside the wifi signal symbol. I don't have this probelm if I'm using my laptop or curve 8520 to connect to the internet via the same wifi router. Please help. Thank you.

Check firewall, if you're on wifi then try ethernet to rule out interference. It is likely a network issue.

Unable to connect to the internet please try again later

I have a blackberry torch 9800, I don't have a data plan. I use a wifi signal with other phones, but my blackberry doesn't allow me to browse or view apps online. The error "unable to connect to the internet please try again later" appears. The phone has a clear signal of the wifi, i've tried various other hotspots, my other phones work perfectly. The blackberry says it's connected to the wifi, but no internet browsing is possible. What else can I do other than rip the battery out to re-boot?

well that sux, are there any alternatives?

"Unable to connect to the internet, please try again" wifi issue

I recently recieved my blackberry storm in the mail excited to use the wifi. I set it up including entering the correct security code a number of time for the "wep" security options and it recognizes the network. I believe it's connecting also, but when I open my browser the message of "Unable to connect to the internet,please try again." pops up. I have a verizon account with a data plan, but due to not wanting to use up my data plan I switched it off as only to rely on my wifi. What can I do? I've updated everything and tried so many things. Our wifi has never done this to any other device. PLEASE HELP!

in the browser, go to the options and setthe default browser as "Hotspot browser" instead of "Internet Browser".
The search box on top-right of this page is your true friend, and the public Knowledge Base too:

HT6001 After updated to iTunes 11.1.4 for windows vista , I was unable to open iTunes and it keep error message. My iphone unable to USB hotspot the internet to computer. Pls Help

After updated to iTunes 11.1.4 for windows vista , I was unable to open iTunes and it keep error message. My iphone unable to USB hotspot the internet to computer. Pls Help

Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2

I am unable to connerct to the internet in my house and was previously able to do so

I am unable to connect to the internet in my home and was previously able to do so. can you help?

If this is the problem following the instruction. Frequently it is a hardware problem.
iOS: Wi-Fi or Bluetooth settings grayed out or dim
Otherwise try (assuming that other devices see your network)
- A reset. Nothing wil be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Power of and then back on your router.
- Reset network settings: Settings>Genral>Reset>Reset Network Settings
iOS: Troubleshooting Wi-Fi networks and connections

Server Loses Ability to Ping to the Internet

Hello,
I have a new physical HP server running Server 2008 R2 with Whats Up Gold. Recently, the server started developing an issue roughly every 48 hours where it cannot ping or use ICMP to the internet. The ability to ping to the internet returns roughly two hours
later after the start of the symptoms or if I perform a reboot. We know this because we have some stuff we monitor over the internet. It has been in production since November and started this behavior in early January for some reason. Nothing has changed to
my knowledge that would cause this issue. It doesn't lose the ability to use ICMP internally just going out to the internet. The local firewall is off and IPv6 is not disabled. I have seen this happen live and have been able to troubleshoot with our
network engineers. They are supposedly not seeing any denials of traffic on their firewalls or load balancers.
So far I have:
1. Changed cabling and switch ports with no luck
2. Worked with HP to replaced the NIC card itself and make sure drivers, BIOS, and firmware are updated
3. Rebuilt the TCP/IP stack on the local server
4. Taken the server out of production, changed the network segment and local IP (to confirm the problem actually isn't a network firewall issue), and the server still isn't able to ping to the internet.
The discovery of #4 leads to me believe it is the server itself. Like I said in the above paragraph, the server's ability returns usually within two hours or immediately after a reboot.
I am on the verge of either rebuilding or demanding HP replace the server. The server is fully up to date on patches and drivers. I just really haven't seen behavior like this that didn't involve changing out the NIC. I am not sure if changing the system
board would do anything per say. I just want to know what else I could be missing?

Hi,
In order to diagnose the issue, I think we confirm some more information.
Did you ping by IP address or domain name?
Run pathping, check the result and post here.
Could you share ipconfig /all with us?
Thank you.

Disregard a ping from the internet???

A common feature of non-Apple routers is the ability to disregard pings from the internet which greatly improves security. I cannot figure out how to tell the APBS to ignore pings on the WAN port. I know this can be done with the Mac OS 10.5 software firewall, but this is not nearly as secure as doing it at the entry point into my entire network (the APBS router).

Hi Cezar,
Thanks for your reply and apologies for my delay getting back to you.
We were effectively thinking to encapsulate a Java or Python call within an ODI procedure, but we were hoping in having an out-of-the-box starting point within ODI.
Will try and see: if you could give me some additional details about it, that would be great!
Thanks again,
scagliaf

HT204400 I am trying to set up my apple tv and i am unable to connect to the internet because i need to get to an internet page to put in my password. HELPPPPPPPPP

I am unable to connect to the internet because to log in i need to put in a password and to do that i need to get to a internet page. helppp

There is no web browser on the ATV, as a result, it cannot be used with such Internet connections.
Contact whomever provides support for the Wi-Fi service, they may be able to add the ATV to a whitelist to allow it to connect.

Unable to Connect to the internet using airport extrteme

I am unable to connect to the internet using airport extreme It was working fine with my G3 & G4 iBooks but now I am unable to connect. I am able to connect directly to my Desktop connecting directly using ethernet. I am also receiving a strong signal from the airport base station. Please help. Thank you.

Try the following, in order, until resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AirPort Extreme Base Station (AEBS), & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AEBS; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AEBS, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AEBS; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."

HT5622 Why am I unable to connect to the internet? I am next to my main computer which has no problems.

Why am I unable to connect to the internet? I am next to my main computer which has no problems.

Try the iPad forum, then:
https://discussions.apple.com/community/ipad/using_ipad
You'll need to include full details, including the model of iPad, the version of iOS, the exact nature and symptoms of the problem, and what if anything you've tried for correcting the problem.
Regards.

I recently downloaded Mac OS X, my wifi is connected but I am unable to get onto the internet. Help?

I recently downloaded Mac OS X, my wifi is connected but I am unable to get onto the internet. Help?

Try restarting the computer or go into network settings and choose assist me at the bottom when your connection is highlighted in the sidebar and follow the prompts

RV042 behind P660 unable to connect to the internet

Hi,
I am a bit new to setting up dual wan router. I am currently having a Zyxel P660 Adsl router but rv042 is unable to connect to the internet as zyxel doesn't give it a I.P address. Thank you guys in advance.

Hello Rashmin,
I am not that familair with the P660 but from looking over Zyxel's website it looks like a modem/router combo.
Is it possible to place the Zyxel into bridged mode, so that it only acts as a ADSL router and passes the public IP on to the RV042? You may need to call your ISP to have them do this for you.
When you are in bridged mode you will also probably have to configure the RV042's WAN port as a PPPoE connection and enter your ISP's credentials, so make sure they give you this when you speak to them about bridged mode.
With some routers it is possible to plug in another router behind them and everything sort of works. This is called a double NAT situation, and does prevent VPN from working. However not even that is working here so I would definitely see about getting that modem into bridged mode. Some ISPs also call it IP passthrough or one-to-one NAT, just tell them you want a public IP on your RV042's WAN port.
Thank you for choosing Cisco,
Christopher Ebert - Network Support Engineer
Cisco Small Business Support Center
*please rate helpful posts*

I am unable to connect to the internet, there is a pop-up that says "We're sorry, but the Safari browse version you are currently using dos no support the community toolbar". My computer does say that it is connected to the internet until I open Safari.

I am unable to connect to the interent. At the top of the screen my computer says that I am connected. When I open up Safari there is a pop up that say "Community Toolbar We're sorry, but the Safari browser version you are currently using does not support the community toolbar" and when the Safari page opens up it says "You are not connected to the Internet. Safari can't open the page .... because your computer isn't connected to the Internet." I have tried Network Diagnostics and tried to reset Sfari, empty Cache as well as deleted all of my interent history. I am unable to use Time Machine because I never set it up. If someone knows how to help I would very much appreciate it!!

Some instructions for removing Community Toolbar are available in this thread: https://discussions.apple.com/message/15868085#15868085

Unable to ping to the internet

Similar Messages

Maybe you are looking for