Unable to play External Midi Instruments in Logic Express

Hi,
I have a Yamaha Keyboard which is connected to my Mac via a usb midi cable (Edirol). I have installed the driver for the midi cable and have set it up properly in the "Audio Midi Setup".
However when I am using Logic Express, I just do not know where I can select the midi cable(Edirol) for my Midi In / Out put and as such, I am unable to play any sounds from my keyboard in Logic Express.
Is someone can advise me on this, would be most grateful.
Thanks in advance and cheers.

Hi
Thanks so much for your reply. I have done so for the setup, however when I am in Logic Express I am still unable to play sounds from my keyboard. The mac seems to be using sounds from the computer instead and I do not know where in Logic Express can i go to set it such that my keyboard sounds are used in stead, as i wish to assign channels to my various midi instruments so that they play the right sound from my keyboard.
Please help!! Thanks

Similar Messages

Volume Problem when using external midi instruments

Hi everyone, I'm having a problem recording the audio from my external midi instruments into Logic 8.
I have all my external midi instruments set up in my environment and they are all going through a motu micro lite interface, with the audio going through a focusrite saffire pro 40.
The way I record Midi into Logic is to load up a new software instrument-select external instrument-find the relevant synth & input-record the midi that I want & adjust as needed-bounce down to an audio channel.
The problem Im having at the moment and have had for a little while is that when I record this way, the audio that accompanies the midi, although I can hear it loudly through my monitors, the input levels in Logic are really small and when I come to bouncing down and listen back to it, it is a lot quieter than I'd originally heard.
With the Pro 40 comes the Mix Control surface, upon checking this the volume on the master output channels is much more representative of the volume I'm hearing through my monitors, and it isn't the same within Logic. I've checked that I haven't got an output coming through channels on this at the same time as its coming through Logic which would result in the sound being doubled and obviously louder, this definitely doesn't appear to be the case.
Its really puzzling and quite annoying me, If anyone could shed any light on why this may be happening that would be fantastic, I've used this forum a few times and I've always found people to be very kind & helpful.

I've checked that I haven't got an output coming through channels on this at the same time as its coming through Logic which would result in the sound being doubled and obviously louder, this definitely doesn't appear to be the case.
It was the first thing I was thinking about. Stop the "Software Monitoring" in the Logic Prefs and try again if you do not have any duplicated hardware routings.
!http://img59.imageshack.us/img59/4967/aglogo45.gif! [www.audiogrocery.com|http://www.audiogrocery.com]

Can I use Mainstage software instruments in Logic Express 9?

I would like to add more software (MIDI) instruments to Logic Express 9. I understand Mainstage comes with what used to be called Jam Packs. Can I use those Mainstage software instruments in Logic Express 9? If not, where do i find additional software instruments?

All JamPacks: yes, no problem.
Actual instruments, effects, like Space Designer: no, they are part of the application code (MainStage or Logic Pro)

Problem playing .mid file with QT Player on an external MIDI instrument

Hello,
I am trying to play a .mid file with QT Player (so I can play it from various softwares as Keynote) and send it out on an attached MIDI device (thru M-audio or Tascam interface). Unfortunatelly, I can only choose "QuickTime Instruments" from the pop-up menu in QT Advanced Preferences. I tried with several configs (G4, G5), several MIDI interfaces, and last flavor of both Panther and Tiger with QT 7.0.4. I configured MIDI setups normally and I can play on exernal instruments from Logic or other sequencers.
Any idea why I cannot see my devices from QT directly ? Thanks,
M

Hello,
I have tried with a Tascam US-428 with 10.3.9 and QT 6 (latest) and 7.0.4 hooked to a Akai S3000. I also tried on a G5 with a MOTU interface (all last software versions). At home, I have tried with my Ti550 running 10.3.9, QT 6 (latest) 7.0.1 and 7.0.4 and also with my Sawtooth (10.4.5, QT 7.0.4), both with a M-audio Uno interface hooked to a E-mu Proteus expander.
All configurations behave the same. They are working fine with various sequencers (Logic, PT, some freewares) but interfaces never show up in the advanced preferences of QT.

Plugins on external MIDI instruments?

is it possible to use plugins on external midi instruments? and if so, how? cant find anything in the manual (although i do not doubt it is in there).
i guessed i could create an audio track, route the inputs from the inputs to which my instrument is connected to on my interface, and insert plugins on the audio track. but im not getting any signal on the audio track, even though the instrument plays fine and i can see it appearing on the relevant inputs on my interface (anyway this was just a guess, that could be the completely wrong thing to do).
i hope that makes sense. thanks in advance.

Set up your midi instruments using a logic "external" instrument. Select it from the instrument list, set in/out assignments and midi channel. Then the sounds will appear on channel strips like an internal instrument allowing full use of all the mixer elements.

MIDI editing with Logic Express (Thinking about buying Express)

I currently use GarageBand to write songs using MIDI. When I want to finalize a song, I use Pro Tools to give it some gentle limiting. I'd use Pro Tools exclusively, but I find GB so easy to use that I can't see myself bothering with PT for MIDI.
How are the MIDI editing capabilities on Logic Express? How would they compare in terms of ease of use versus GarageBand (and Pro Tools, for that matter)? Is there another program out there that's great for MIDI editing/programing? Can GarageBand export MIDI (I doubt, though...).
[ I wish I could use the software instruments found (free) in Pro Tools with GarageBand, seeing as how I'd have a little more to choose from and a bit higher quality. How would you rate the software intruments found in Logic Express? ]
MacBook (2 GHz Intel Core 2 Duo, 2 GB 677 MHz) Mac OS X (10.4.8) GarageBand & Pro Tools

Hi Jose,
My version of Protools is 6.4, so the midi editing in Logic Express,
is far better, if you like GarageBand you'll probably Love Express,
apart from the learning curve everything's better.
Better than Express only Logic pro.
Every sound you have in GB you have in Logic ( I believe they share the same audio engine) but with the benefit the plug-ins (32 bits internal process it sounds better) also you can twick the sounds, plus you have Soft synths and sampler with loads of new sounds.
Cheers,
Jorge

$5 Starbucks card to first successful answer: how to import midi timecode into Logic Express 9 from Roland VS-880 or Ensoniq ASR-10

I will literally mail a $5 Starbucks card or gift $5 via paypal to the first person whose response gets me success. Then after all responses are provided and I'm successful with my issue, I'll also raffle off $5 to one of ALL respondents by random pick.
Problem/question:
I can't figure out how to import midi timecode data from either an Ensoniq ASR-10 or Roland VS-880 Vxpanded into Logic Express 9, so I can then use Logic Express 9 as the master. No manuals seem to explain that; I just can't find it.
Background/basics:
1. My ultimate goal will be to move all midi data from the Ensoniq ASR-10 floppies and all digital audio files from the VS-880 into Logic Express 9. Once the midi timing is imported into a Logic Express 9 file, I'll import the data from the Ensoniq & Roland via steps 2a & 2b below.
1a. Ten years ago I somehow (am in the process of re-learning what I did 10 years ago) imported the midi timing into the Roland VS-880 Vxpanded from the ASR-10, and then used the VS-880 as the Master to control the ASR-10. So my current status is that I use the Roland VS-880 as the master, and the Ensoniq ASR-10 as the slave.
2. FYI for anyone who might be in the same boat, wanting to transfer stuff from an Ensoniq ASR-10 and Roland VS-880 to the computer:
2a. I will import all midi sequence data from my ASR-10 floppy disks via a utility purchased here, which will all a PC to read Ensoniq-formatted disks, and then just hopefully cut/paste midi files into Logic Express 9 (FYI only): www.chickensys.com
2b. Then will import all the individual WAV files from my Roland VS-880 to Logic Express 9 using a method learned here (FYI only): http://www.vsplanet.com/ubbthreads/ubbthreads.php?ubb=showflat&Number=985974&PHP SESSID=b1d2f57be4a1d37d49787400213b22df
2c. I'll then combine them all into Logic Express 9.
So - how the heck do I capture/import the midi timecode into Logic from either the roland or ensoniq using midi?
I'm don't think that cutting/pasting the midi data into a Logic Express 9 sequence file (step 2a above) will do that, because there are all kinds of tempo & time signature changes in the midi files unfortunately.
THANK YOU and Merry Christmas!!
Andy

OK doesn't look possible. Closing discussion.

Import midi-file to logic express 7

hi there
i'm trying to import a midi-file to logic express 7.
always when i import it, there comes a window with "new smpte-frame rate". when i click ok, it doesn't import anything... what can i do?
ps: sorry for my english!

thanks, it works with some midi files. but when i'm saving a file in finale 2007 as a midi file, it doesn't work... i checked the sync prefences and they don't look wrong... it's really strange!

Use exterior vst instruments in Logic Express 9

From my former PC I installed Cubase Essential5 onto my new iMac and I purchased Logic Express 9 as well. I am trying to find out wether I can use the HALionOne and Synth Prologue vst instruments in Logic Express and how I go about it. I did install a demo version of Musiclab's Realguitar and after checking the Audio Units Manager, installment I was able to open this under Exterior instruments. Does anybody have suggestions?
evert

Hi
Logic only supports Audio Unit plugins, not VST (or any other type). Install the correct type and you should be good to go.
CCT

MIDI plays in GarageBand, but not Logic Express

hi, all...when i drag or import a MIDI file that i know works in GarageBand into Logic Express, i can see all the different tracks and notation, but when i press play, no sound comes out, tho the measure line is moving and the volume indicators are lighting up.
any clue what's going on?

This has already been discussed here numerous times. You should do a search on the forum and read the Logic for Garage Band Users pdf. When you open a midi file in Logic, the tracks are not assigned to virtual instruments like in GB, they're only midi tracks. If you want to hear sounds, you have assign them to an external sound module, to the QuickTime synth available in Logic or you have to create audio instruments tracks and move you midi data to those.

Using a second computer as a external midi instrument or DAW slave?

So this is my current setup:
iMac 24(FW 800 & 400) with logic 8 & reason 4,
Focusrite Saffire Pro 40 firewire (x2) sound card/pre-amp,
Blackbook with MainStage & Reason 4.
& this is what I would like to do:
Use my imac as my main DAW master, (currently tracking to an external FW800 drive & pulling loops from a USB drive), & use my blackbook to run reason as a external midi device or slave.
My Saffire Pro 40 has 2xFW400 ports so I can connect both machines to it.
The idea behind this setup is to pull as many software sounds from the Blackbook & mainly use the imac to run Logic.
Does this make sense? & if so, what's the best way to execute this?
thanks in advance

Hello -
I'm not entirely sure that one audio device such as the Saffire Pro 40 with 2 Firewire ports can be shared between two computers. It was always my impression that the second Firewire port was available to "daisy chain" another audio device or hard drive. Before you proceed, you might want to check with the company that manufactures the Saffire Pro 40 and make sure that two computers can interphase with it.
With regards to using a second computer as a "slave machine", it seems that many, many people do have such configurations to help spread the CPU and memory work-load. My happy Mac Pro is set up to work with a potential of two other "slave machines". When I use this set up, it works wonderfully. But, for most of the time, my happy Mac Pro can manage most sequencing projects (mostly orchestral with LOTS of instruments) on its own. Each computer, however, has its own audio device. All are connected to the Mac Pro using the ADAT light inputs/outputs from each audio device (I use MOTU's audio devices) and are managed midi-wise using Music Lab's MOLCP 3.
Good luck. . .

How do I record multiple midi instruments in Logic Pro simultaneously on separate tracks?sim

Hi. I am trying to record multiple midi instruments simultaneously into Logic Pro 9 through a MOTU USB Fas Lane so that it is similar to recording a live band.
Essentially:
Track 1: Midi Keyboard - Motu Fast Lane Input A - Logic Pro - Software Instrument (Absynth)
Track 2: Midi Drum Kit - Motu Fast Lane Input B - Logic Pro - Software Instrument (Battery)
Neither Midi device can be set to a separate channel.
I would have thought this was a really common application (recoding from multiple live midi sources like a band would normally do) yet it seems unnecessarily complicated.
I gather what I would have to do involves:
1) Going into the Environment.
2) Creating a Physical Input
3) Creating a Sequencer Input
4) Placing a transofrmer between the Physical Input and the Sequencer Input
Where to go ffrom there I have not got a clue!
Any help would be appreciated.
Incidentally I would also like to record two audio tracks at the same time as the midi track, but hoepfully that does not complicate things further.
Thanks,
Luke

I have it set to Performance mode which according to the owners manual: "This mode makes the XP-30 function as a multitimbral sound
source, and Performance settings can be modified. If you’re
using an external MIDI device to control the XP-30 in this
mode, it will function as a multitimbral sound source."

How do you record an external Midi Instrument + Software instrument track down to a combined Audio track ?

I have two piano sounds I'm trying to blend into one. One is an external MIDI module set up as an external instrument within Logic and the other is a software plugin instrument (Ivory II). I'm trying to record the blended pianos into a single audio track so I can ditch the midi track and more so the CPU intense software Instrument track (it's killing my setup....). For the life of me I can't figure out how to assign both these entities as inputs and get them to record simultaneosuly onto an audio track.
My setup is a Presonus Studiolive 16.4.2 with the following assignments:
The external MIDI module's audio output is routed stereo directly into channel strips 9 and 10. By default the firewire output of this channel strip is returned to firewire outputs 9-10 on the studiolive, but this really doesn't matter since recorded audio is being monitored thru the main output buss assigned to channels 17 and 18.
My software plugin (Ivory II) is routed to output channels 17 and 18 which is the default setting for routing the output to the master buss for the Presonus.
On my audio track that's setup in Logic I can assign the inputs to 9 and 10 and I get the external midi module's output to record, but I cannot find any way to get the software instruments output into this mix because there is no input assignment for this.
Is there any way to combine these two entities and assign them to record onto a single audio track or am I missing something here? If there's no simple way to do this, can somebody offer any tip or ideas on how to accomplish the same thing here. I really need to ditch the software plugin. My setup only seems to be able to handle one plug in at a time on the software instrument side. Not sure why that is because my setup is not that old and the memory on my MBP is maxed out at 4GB....but that's another topic of discussion
Any suggenstions would be much appreciated...

Thanks for the reply....
I actually tried freezing the software instrument track and that had little if no effect on CPU. I then read in the book or somewhere that the freeze function really only works on effect plugins. Don't know if that's true in all cases, but that seems to be what's happening. Still would like to combine these tracks and I'm guessing I'm going to have to get creative with bussing or subgroups to make this happen. Unfortunately I think the fact that my Presonus board has hardmapped output routings for all the inputs makes that difficult, but haven't actually tried yet. I'm thinking if I can reroute the midi modules audio output input into the Presonus to a subgroup and then route the software instrument plug in to the same subgroup that I can then mix/capture this and hopefully route the audio's input to the subgroup to pick up the mix.
Does this make sense to anybody reading this?
We'll see and I'll post the results if it works....
thanks...b

How do I keep my Patch names for my external Midi instruments when starting

Whenever I start a new project all the names in the different banks are just numbers.
I use a JV-2080 with expansion cards which represent close to 2000 patch names in 11 banks.
(I have some other Midi instruments too with their banks)
I have a "basic setup" project where all the patches for all the instruments are loaded, and until I know a better way, I always start with that "basic setup" and then modify it and "save as" a new project.
Is that the only way? or is there a way to automatically load all the patch names in the Multi Instrument window?
I find it very annoying that I cannot start a project from scratch, without having to copy and paste hundreds of patch names.
I read somewhere in the manual that "initializing" the banks in the Multi Instrument Window, occupies extra memory. I find this comment very strange because the text file containing all my patch names is only 24kB just a drop in the bucket.
Or am i missing something?

The whole point of autoload temapltes is you setup a Logic song to contain all the stuff you need, environment configuration, patch names, track assignments and so on, so whenever you load Logic or start a new song, all your stuff is instantly there.
Think of it like a real studio - when you start a new song, you don't unpack all your gear from boxes, put them on shelves, and wire them up etc before you start - that stuff is all done once beforehand. You just turn them on, and go.
Same with Logic - it loads your startup template with all your stuff in it, so you can immediately just start doing music, with no futzing necessary.

HT4623 unable to play external music on my ipod touch.....nor during apps sound without hear phones pls help.

please hepl unable to hear external sonund...tried restore but no use hoping something useful from u..

- Try cleaning out/blowing out the headphone jack. Try inserting/removing the plug a dozen times or so.
Try the following to rule out a software problem
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iPod.
- Make an appointment at the Genius Bar of an Apple store. Seems you have a bad headphone jack.
Apple Retail Store - Genius Bar

Unable to play External Midi Instruments in Logic Express

Similar Messages

Maybe you are looking for