Unable to regenerate /dev/rmt/0 drivers with cfgadm -c configure on Solaris 10 update 11 (1/13). How does one do this for SAS HBA StorageTek Autoloader?
How does one regenerate the /dev/rmt/0 when cfgadm -c configure <device> will not rebuild it? Have attempted reboot -- -r, with modifing /kernel/drv/st.conf as well as /kernel/drv/sgen.conf. Running on a SPARC T4-1 Solaris 10 updat3 11, (1/13).
This has been resolved. Getting the /etc/driver_aliases set correctly: # update_drv -d -i st; update_drv -d -i sgen; add_drv -m '* 0600 root sys' -i '"scsiclass,01" "scsiclass,08" wa' worked. Making sure the st and sgen entries are in /etc/name_to_major were needed. For the Simpana/CommVault WA drivers, in opt/simpana/WA/wa.conf with the name="wa" parent="fp" target=16 lun=0 fc-port-wwn="device's World Wide Number> added for each lun 0 to 7. Then the touch /reconfigure; reboot worked. First the c1::rmt/0 tape and c1::scsi/changer/<wwn> med-changer were mapped. After modifying the minor_perm ('* 0600 root sys') and name_to_major entries, the WA CommValt entries , WA drivers showed up in cfgadm -al as c1::wa0 tape and c1::wa1 med-changer, only recognizable from CommVault. Also had to update the SAS-2 HBA StoregTek Autoloader driver with patch 145648-05. Solaris 10 update 11 (1/13) comes with 145648-03. In our particular case, we found cfgadm -al mapped SAS-2 HBA to c1 using the single mini-sas 6gb connector cable, where it mapped to c7 with the four tail connector.
Similar Messages
-
With my new macbook I attempted to open an older spreadsheet and get the following error message: "This spreadsheet cannot be opened because ti is too old. To open it, save it with numbers '09 first" So how does one do this when I only have ver3.1?
Numbers 3.x can only open Numbers '09 and later. You will need Numbers '09 to open Numbers '08 files.
If it is a single file (or only a few) you can email me and I will open and convert then email back. My email address is in the "Biography" of my profile.
You may have Numbers '09 installed. Look in the folder "/Applications/iWork '09" if Numbers is in that folder launch it, open the file you tried to open, and save. Then you should be able to open in Numbers 3.x -
How Does one fix this-"This Mac can't connect to iCloud because of a problem with "My Email Address"
Hello Apple Community: I receive this message multiple times a day.
"This Mac can't connect to iCloud because of a problem with "My Email Address" Open iCloud preferences to fix this problem.
After sighing into iCloud I can not find a problem.
Is this a Yosemite issue, because thats when the issue started?
Thanks for your help..Yes, this is a constant problem for me as well. I have 2 Macs (iMac and old MacBook Pro) running Yosemite. I seem to only get this message on the iMac. I've tried logging out of ICloud on both and logging back in; the problem re-appears randomly. I also have no issue on IOS devices.
It's mainly annoying. I open the iCloud panel in System Preferences and it tends to go away. -
Unable to write the email to the mailbox - how does one fix this?
Cannot download messages to inbox because of above. Says also to check write messages
One possible cause for the problem is that your anti-virus s/w has quarantined your Inbox, and thus preventing Thunderbird from writing to it.
Check your anti-virus s/w for quarantined items.
Try to temporarily disable your anti-virus s/w.
Also check your free disk space. -
Regarding iMessage, when i want to send text to a person in my contacts app, i've been getting a message saying the number has not been registered with iMessage. How can one fix this problem? It works on the iPhone.
It takes two to tango, maybe it's your recipient that has weak Internet/Cellular connections.
-
How does one continue to use Mail on the early MacBook Pro, Model 1,1, that is not upgradable to Lion? I have been running iCloud on my iPhone (OS5) and iMac (Lion) along with the MacBook Pro (OS Version 10.6.8) since November until now. Mail will no longer download on the MacBook Pro and keeps asking for my password.
Mail should still be usable with your machine - but you'll need to update the settings to conform to the requirements of your system. Check with your ISP (like ATT, etc.) for the settings that will work with your Mail. Once you've updated this, you should be able to email like before.
For example, my ISP required that I go to Mail Preferences/Accounts and make sure the details conform to your email settings.
I have no idea of what your ISP is or what the settings might be, but this is likely the source of the problem. -
How does one sync music from iTunes on a Mac with an HTC Windows 8 phone
How does one sync music files from iTunes running on a MacBook Pro with an HTC Windows 8 phone?
One doesn't.
Itunes syncs with Apple devices.
You can put the music on your phone. You would have to read the directions for your iphone to learn how to put your music on it. -
Itunes 11.1.5 (MacBook Pro,OS 10.6.8) will not sync new apps with iPhone 5 iOS 7.0.6 and gives grayed out "install" no message? How does one work around this?
Just reboot your laptop... While its rebooting try to reboot your phone also by holding the home and power buttonn for 10-15 seconds...When your phone is turned off try to connect it to iTunes and it will recognize your phone in recovery mode.
If you have the .ipsw file for iOS 7.0.6 saved in your desktop then in itunes press shift and click on Restore.
Select the ipsw file and let it restore.
If you dont have it downloaded then simply click on restore.
I hope it works
Cheers ! -
How does one install non-English character sets for use with the "find" function in Acrabat Pro 11?
I have pdf files in European languages and want to be able to enter non-English characters in the "find" function. How does one install other character sets for use with Acrobat Pro XI?
Have you tried applying the update by going to Help>Updates within Photoshop Lightroom? The update should be using the same licensing? Did you perhaps customize the installation location? Finally which operating system are you using?
-
ipad is asking for a passcode which I never installed. iPad is now disabled. Tried syncing to itunes with my mac book pro, won't sync. How do I fix this?
Recovery Mode
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
3.While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: Data will be lost. You may have to repeat the above many times. -
I got a 8gig ipod touch from a freind and all I get on the screen is a usb plug with an arrow pointing towards the itunes logo. How do I resolve this? I don't know what operating system it runs, or what year it was manufactured, it is a chrome one.
http://support.apple.com/kb/TS1369
There have been some problems accessing pages on the Apple web site. If the hyperlink gives you a "We're sorry" message, try again. -
I'm having problems with iPhoto and the facebook set-up. Every time I attempt to do so it says an error has occured and try again later. I have not seen a solution posted. Therefore, how does one contact Apple to solve the problem? I'm new to the world of iMac but I find it a bit frustrating trying to solve basic issues/problems:(
For what it's worth, you posted this in 2011, and here in 2014 I am still having this same issue. Over the last two days, I have had to unlock my apple account 8 times. I didn't get any new devices. I haven't initiated a password reset. I didn't forget my password. I set up two factor authentication and have been able to do the unlocking with the key and using a code sent to one of my devices.
That all works.
It's this having to unlock my account every time I go to use any of my devices. And I have many: iMac, iPad, iPad2, iPad mini, iPhone 5s, iPod touch (daughter), and my old iPhone 4 being used as an ipod touch now. They are all synced, and all was working just fine.
I have initiated an incident with Apple (again) but I know they are just going to suggest I change my Apple ID. It's a simple one, and one that I am sure others think is theirs. I don't want to change it. I shouldn't have to. Apple should be able to tell me who is trying to use it, or at least from where.
Thanks for listening,
Melissa -
I have a problem with my ipad when choosing software update it is continously loading the message checking for updates without showing any results
Hello SuzMiller
Check out the article for the troubleshooting steps for issues with email on your iPhone and iPad.
iOS: Troubleshooting Mail
http://support.apple.com/kb/ts3899
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
My Mom has tremors and when she uses her iPhone and taps to select, the way she hits the keyboard causes the copy selection to appear. It is not an issue with her phone because it does not do this for me. I would like to shut off the double tap feature. I have already tried Settings/General/Accessibility/Home speed typing = slowest.
The editing menu doesn't come up when you double tap. It comes up when you press and hold. It can't be turned off.
-
How does one transfer CS5 actions for use with CS6?
CS6 installation, which was uneventful, has transferred none of my actions from my copy of CS5. The CS5 actions are located in the actions folder of the APPLICATION/PHOTOSHOP CS5/PRESETS/ACTIONS. The "actions" folder in application support/adobe in my library is empty, and has always been so.
Only the CS6 default actions are located in the same folder for CS6.
I use imac i7, lion.
Note that i also have CS3 and CS4 on my machine. This due to recent upgrade to CS5 and recent upgrade to LION, and my general paranoia.
Must i load each action into CS6, one at a time?
thanks to any and all.
vinceRe: how does one transfer CS5 actions for use with CS6?
On a Mac - There are multiple ways to do this. I have done them both ways. In order to do this you need to know where you have your actions stored, and you can move them all at once if you have them stored in the same location.
1. You can load an action ONE AT TIME into your actions palette by:
A. Open up the action palette and click on the little arrow with 4 little horizontal lines next to it on the upper right corner of the actions palette.
B. Select "Load Actions" and a Finder window will open up and you can search your computer through this window for your actions.
C. Click on the action from the Finder window then click 'Open' at the bottom right of the finder window.
D. To save these so that they appear every time you open up your actions palette, go back to the little arrow at the top right of the actions palette and when the drop down window opens- click on 'Save Actions'. It will select the location where the actions are currently stored as the place to save them. If you want to change that path, you can do it at this time in the little path window. I just leave it, since I keep all my actions stored in the same file.
2. TO MOVE MULTIPLE ACTION SETS AT ONCE
A. Open up CS6 (or CS5) and move the Photoshop workspace it to the right side of your computer screen so you can see your desktop on the left side.
B. Open up your Finder search window from your dock (the square blue head icon thingy for those who are new to photoshop). Move this to the left side of your screen so you can see the Photoshop work space on the right and the Finder window on the left. In the Finder window, navigate to the file where all your actions are stored, select all the actions in the file (command+A will select everything in the file if you are actively inside the open file) or you can select multiple files individually by continuously holding down the command key and clicking on the different actions you want to move.
C. With the Photoshop workspace visible on the right, and the actions palette open so you can see that the actions actually transferred - In the Finder window, click the selected actions you want to load and drag them over to the Photoshop workspace. I did this without an image open, I just dragged them onto the empty workspace. The actions should all appear immediately in the actions palette that is open.
D. To save these so that they appear every time you open up your actions palette, go back to the little arrow at the top right of the actions palette and when the drop down window opens click on 'Save Actions'. It will select the location where the actions are stored as the place to save them. If you want to change that path, you can do it at this time in the little path window. I just leave it, since I keep all my actions stored in the same file.
I hope this helps.
and I hope there are no typos.
Maybe you are looking for
-
My ipod doesn't get recognized by my pc
hi, for a longer time now, i've got several problems with my ipod nano, the first is, the ipod doesnt really start, it shows the apple logo and after that it turns off and restarts... and thats what it does all the time, until the battery is empty...
-
Junk characters displayed when viewing BEx query through WAD
Hello, I am trying to display the results of a web report containing a BEx query through the "Execute in the Browser" option in WAD. But, junk Chinese characters keep showing up in the display. Also, if I try the same with one of the older web report
-
Help: Installing 8i Enterprise Edition
I am new to installing Oracle myself and I am in the process of doing that now, and I am facing problems. I really need someone to act as my mentor, so I can direct my questions to them. If anyone is willing to help please let me know via e-mail. I p
-
We are looking for a tool for displaying help from a fortè application. Considering our target clients, a multiplatform tool is needed ( w95/NT & unix plat). We have taken into account an html document browser, launched ( via runcommand for instance
-
whenever i download something it wont open, it looks like a blank sheet of paper, especially .exe files. every thing i download will not open right