Unable to restore iPhone - Error 1603

Hi,
Used iTunes to update my iPhone 3Gs to the latest version and am currently stuck.
iPhone is in "ready to restore mode" (showing the connect to iTunes picture)
Am unable to restore the iPhone, when I press restore in iTunes, it prepares the device for restore, then after a while displays Error 1603.
I have tried restarting the computer, "hard restore" of my iPhone, reinstalling iTunes and also turning off my antivirus.
I have the latest version of iTunes installed and my operating system is up to date.
Appreciate any help as I am unable to receive any calls at the moment.
Cheers,
Brock

Thanks amy_lou.
I tried below steps as mentioned in link:
1) stop and start apple mobile service .
2)change administrator .
not sure which one worked but got my phone restored succesful .

Similar Messages

  • TS3694 unable to restore iphone error code 3194 keeps coming up what do i do?

    unable to restore iphone 4 - error code 3194 keeps coming up what do i do ?

    Error 1004, 1013, 1638, 3014, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
    Install the latest version of iTunes.
    Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
    Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. FollowiTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
    Try to restore from another known-good computer and network.
    If the errors persist on another computer, the device may need service.

  • Unable to restore iPhone. error code 21

    I am unable to restore my iPhone through iTunes. I keep getting an error code 21 after trying recovery mode. please help, I've followed work around instructions on apple, but no luck. Also because the phone will not turn on I am unable to locate serial number for the device.

    If you have tried the troubleshooting steps outlined in this article for Error 21 unsuccessfully, then you will need to contact Apple Support to get help:
    Resolve specific iTunes update and restore errors
    https://www.apple.com/support/contact/
    Best of luck,
    GB

  • Unable to restore iPhone 5S with iOS 8.2 (Error -1)

    Unable to restore iPhone 5S with iOS 8.2 (Error -1)
    I tried to install previous versions 8.0 and 7.0.3, it returns another error.
    I tried with iTunes 12.1.1.4 and 11.2
    Even in DFU mode its giving the same error.

    Hey BBRemoshan,
    Thanks for the question. If I understand correctly, you are trying to restore the iPhone and are getting errors. I would recommend that you read these articles, they may be helpful in troubleshooting your issue.
    Resolve iOS update and restore errors in iTunes - Apple Support
    Get help with iOS update and restore errors - Apple Support
    Thanks for using Apple Support Communities.
    Have a good one,
    Mario

  • Unable to restore iphone 3gs to factory settings, unknown error occurred (-1) can anyone help

    i am getting an error ...unable to restore iphone "iphone" unknown error ocurred (-1) and the iphone is stuck on itunes connection sign. any idea how i can restore factory setting  it is ne iphone 3gs with ios 5

    This is indicates a hardwre issue:
    Check for hardware issues
    Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
    Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support.
    Error 1015 might happen after making unauthorized modifications to iOS, also called "jailbreaking."
    Use recovery mode to restore your device
    Related errors: 1015, “The required resource can't be found.”
    You might see these error messages if your device has a beta version of iOS or if you're installing an older version of iOS (downgrading). Use recovery mode to restore your device to the latest version of iOS.
    Quit virtualization software
    Quit any virtualization software (such as Parallels or VMware) that’s running on your Mac. Then use the latest version of iTunes to restore your device.
    Resolve specific iTunes update and restore errors

  • HT4061 unable to restore iphone

    Hi, I connected my iphone 4 to my computer to update and now receive an error on my computer "unable to restore iphone" and nothing on my phone works now.  appreciate any help

    For a Windows PC: iOS: Device not recognized in iTunes for Windows - Support - Apple
    For a Mac: iOS: Device not recognized in iTunes for Mac OS X - Support - Apple

  • HT201263 Hi. I forgot my passcode and now I am unable to unlock my ipod. I tried restoring it using itunes in recovery mode as well as dfu mode but it says unable to restore,unknown error occured (3004).  Please help me out. My ipod is locked for one hour

    Hi. I forgot my passcode and now I am unable to unlock my ipod. I tried restoring it using itunes in recovery mode as well as dfu mode but it says unable to restore,unknown error occured (3004).  Please help me out. My ipod is locked for one hour now.

    Locked Out, Forgot Lock or Restrictions Passcode, or Need to Restore Your Device: Several Alternative Solutions
    1. iOS- Forgotten passcode or device disabled after entering wrong passcode
    2. iPhone, iPad, iPod touch: Wrong passcode results in red disabled screen
    3. Restoring iPod touch after forgotten passcode
    4. What to Do If You've Forgotten Your iPhone's Passcode
    5. iOS- Understanding passcodes
    6. iTunes 10 for Mac- Update and restore software on iPod, iPhone, or iPad
    Forgotten Restrictions Passcode Help
    You will need to restore your device as New to remove a Restrictions passcode. Go through the normal process to restore your device, but when you see the options to restore as New or from a backup, be sure to choose New.
    Also, see iTunes- Restoring iOS software.

  • Email address hacked via iphone. iphone locked home screen displaying my email password! and has been reset. now unable to restore iphone, saying i do not have permission

    Email address hacked via iphone. iphone locked home screen displaying my email password! and has been reset. now unable to restore iphone, saying i do not have permission

    If you don't know your password, don't know your security questions and don't have a rescue address or don't receive a reset email, you should contact AppleCare who will initially try to assist you with a reset email or if unsuccessful will pass you to the security team to reset your security questions for you.
    If you are in a region that doesn't have international telephone support try contacting Apple through iTunes Store Support.

  • Unable to restore iPhone 6

    i'm unable to restore iPhone after it was blocked mistakenly typing wrong pass code while the display was broken. please suggest how to restore.

    Hello Zaiduzamaan,
    Thanks for using Apple Support Communities.
    If you have a message on your iPhone that it is disabled, then you will need to erase it by following any of the methods outlined in the article below.
    Forgot passcode for your iPhone, iPad, or iPod touch, or your device is disabled - Apple Support
    Take care,
    Alex H.

  • HT201210 UNABLE TO RESTORE IPHONE 3

    i m unable to restore iphone A1241 gettina an error

    Try to follow below two ways to restore iPhone:
    1) Connect your iPhone with computer using bluetooth or USB Cable.
    >>Open iTunes
    >>Go to "Storage"
    >>Click on "Backup and Restore"
    >>Wait for a moment.
    Your contacts will be restored.
    OR
    2) Open iCloud.
    >>Enter Apple id and password.
    >>Go to Storage and Backup
    >>From there Restore your contacts.
    >>Close iCloud.
    >>Restart iPhone.
    You are done.
    <Link Edited By Host>

  • Unable to restore iphone 4s.Error message 2001.

    hi
    i updated my iphone 4s to ios8. Phone went off due to no battery, when i switch on, its rebooting over and over.Now i tried restoring the phone but the error message 2001 saying i am unable to restore.
    Need some advice
    Thank you

    iphone1 wrote:
    I had the same problem.  To fix it, I first tried a different computer and different USB cable.  When the error still appeared on the different computer and different USB cable, I unplugged the USB cable from the iPhone, opened up the iPhone and disconnect the battery from the iPhone main logic board (three screws).  I left it unplugged for a few hours.  Plugged back in the battery connector and then restored in iTunes.  Hope this works for you.
    Um, no.  Opening up the iPhone voids all support from Apple.  Do not make recommendations on this forum that will violate Apple's policies or procedures.

  • Unable to restore iphone 4 to original factory settings? error 10??

    unable to restore to factory settings?? error 10??? itunes unable to recognise iphone??

    error code 1602 http://support.apple.com/kb/TS3694#error1602

  • Unable to restore Iphone 3GS 1604 Error

    Hello,
    I have been trying for hours to restore Iphone 3GS in XP. All i did was click "yes" to update iphone and now I am in a mess. Tried reinstalling, different ports, different cables, still unable to restore.

    I'm not sure, or else more people would be posting about it. Best way to tell is try at a different time.
    Also, you could try putting the phone in Forced Recovery mode as outlined in http://support.apple.com/kb/HT1808.
    Also, are you using iPhone cables or iPod cables? If you're using the appropriate cable and the same thing happens, then hopefully your phone is still within warranty and you can go to an Apple Store for the Genius Bar.

  • Preparing ipod for restore then error 1603

    I've been trying to update my ipod touch 4G for 3 weeks. I download ios 5.0.1 and then tried to restore it manually. First i got the error 3194 and 2005. I tried changing host files, putting in DFU mode, using fixrecovery and so on n then those errors disppeared. But now everything's running smoothly until 'Preparing ipod for restore'. As soon as it starts, ipod went into recovery mode and that preparation stage would last around 4 mins and error 1603 or 1604 appeared. It's been going on for a long time and i find no solution. Plus i want to know if ipod normally goes into recovery mode when restoring cuz i've put it into DFU mode already.
    My current ios is 4.1 and i m running window 7. Somebody pls help me?

    Did you try:
    Error 1603: If you receive this error and the iOS device is not automatically placed into recovery mode, it may be necessary to do so manually. Refer to iPhone and iPod touch: Unable to restore for steps on placing iPhone into forced recovery mode. Also, remove the IPSW and attempt to restore again. If you do not want to remove the IPSW in the original user, try restoring in a new administrator user.
    Error 1604: This error is often related to USB timing. Try changing USB ports, uninstalling and reinstalling USB ports, and other available USB troubleshooting steps (troubleshooting USB connections, device not recognized properly, computer won't recognize a FireWire or USB device). If you are using a dock, bypass it and connect directly to the white Apple USB dock connector cable. If the issue persists on a known-good computer, the device may need service.
    If the issue is not resolved by USB isolation troubleshooting, and another computer is not available, try these steps to resolve the issue:
    Connect the device to iTunes, confirm that the device is in Recovery Mode. If it's not in Recovery Mode, put it into Recovery Mode.
    Restore and wait for error 1604.
    When prompted, click OK.
    Close and reopen iTunes while iPhone remains connected.
    iPhone should now be recognized in Recovery Mode again.
    Try to restore again.
    If the steps above do not resolve the issue, try restoring using a known-good USB cable, computer, and network connection.
    Above from:
    http://support.apple.com/kb/TS3694#error1603

  • Unable to restore iPhone 5s

    My iPhone 5s was displaying searching for network for a couple of days unexpectedly. I backed up the phone on iCloud and then tried to update to 7.1 but couldn't die to some error. Then I tried to update the phone from iTunes it failed showing error 3. Then I tried restoring it, same result unable to restore error 3. Please help!

    Hi Karan239,
    Welcome to the Support Communities!
    The article below may be able to help you with this.  Click on the link to see more details and screenshots. 
    Resolve specific iTunes update and restore errors
    http://support.apple.com/kb/ts3694
    Check for hardware issues
    Related errors: 1, 3, 10-47, 1002, 1011, 1012, 1014, 1000-1020, 1669.
    Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good. Also, confirm your security software and settings are allowing communication between your device and update servers. If you still see the error message when you update or restore, contact Apple support.
    Error 1015 might happen after making unauthorized modifications to iOS, also called "jailbreaking."
    Use recovery mode to restore your device
    Related errors: 1015, “The required resource can't be found.”
    You might see these error messages if your device has a beta version of iOS or if you're installing an older version of iOS (downgrading). Use recovery mode to restore your device to the latest version of iOS.
    Quit virtualization software
    Quit any virtualization software (such as Parallels or VMware) that’s running on your Mac. Then use the latest version of iTunes to restore your device.
    I hope this information helps ....
    - Judy

Maybe you are looking for

  • Command line arguments

    Hey there, I have a program that uses a command line argument at runtime to get a txt file which is then loaded into my program. c:\>java FileName infile.txt I want to catch what args[0] is so I can print the file name the user entered to the screen

  • Max SGA size?

    I've got a box with 2 gigs of RAM, but no matter what I set the kernel and init.ora parameters to, I can't start an instance with more than an 800 meg SGA. That's any combo of db_block_buffers and shared_pool_size. I get a Linux error 22 or something

  • VERIZON INTERNET SECURITY SUITE ANTI VIRUS NOT COMPATIBLE WITH WINDOWS 7

    It seems to me that Verizon/Radialpoint should have figured out the solution for this long before Windows 7 hit the streets but here we are a month later and still no anti virus from the product we're paying for. I've wasted countless hours with all

  • Problems Removing Secondary Domain and agents

    I had a secondary Domain and a gwia and webaccess agent running on an vm box. The box had issues and crashed and I was unable to recover it. I am now left with a secondary domain and two gateways that I can cannot get rid of because the edir objects

  • Navigation when reviewing a quiz

    Hello, I have created a quiz in Captivate 3, and enabled the review functionality in Captivate. Upon completing the quiz, on the score page is the the option to review the quiz. Upon pressing this, it goes to the first question properly and displays