Unable to save config in ASA 5505
Hi all,
I have ASA 5505 and
Hi all, I have this issue, I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.
Please help
Thanks
MAhesh
i can save the config now and did reload.config is saved now.
The config was also saved before. But due to the config-register the startup-config was not applied after loading the image.
it shows no file name is this normal?
If you don't see any variables in "sh bootvar" it defaults to the first image in flash and the saved startup-config. So everything fine here.
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni
Similar Messages
-
Save configuration in ASA 5505
Hi all, I have this issue, I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.... then what i do is a copy start run to get the configuration active....
why is this so? even though i saved the config to flash ... regards!You have incorrect boot register:
Please follow up the following document:
http://www.cisco.com/en/US/docs/security/asa/asa71/configuration/guide/trouble.html#wp1062992
You need to set up default value 0x1
HTH. Please rate this post if it was helpful. If this solves your problem, please mark this post as "Correct Answer" -
Problem with saving config on asa 5505
I have asa 5505 with 512mb , i am trying to save ios on it but i failed many times , I have sandisk 2GB and i formatted with windows on fat but every time i see disk0 failed , any ideas what is the problem ?
ThanksI have asa 5505 with 512mb , i am trying to save ios on it but i failed many times , I have sandisk 2GB and i formatted with windows on fat but every time i see disk0 failed , any ideas what is the problem ?
Thanks -
ASA 5505 Unable to assign ip to DMZ vlan interface
hi all,
I have ASA 5505 with base license.
I created 3rd vlan on it.it was created.
but i am unable to assign IP to it.
i assign ip address it takes it.
But when i do sh int ip brief it does not show any ip.
ciscoasa# sh int ip brief
Interface IP-Address OK? Method Status Prot
ocol
Ethernet0/0 unassigned YES unset up up
Ethernet0/1 unassigned YES unset up up
Ethernet0/2 unassigned YES unset up up
Ethernet0/3 unassigned YES unset administratively down down
Ethernet0/4 unassigned YES unset administratively down down
Ethernet0/5 unassigned YES unset administratively down down
Ethernet0/6 unassigned YES unset administratively down down
Ethernet0/7 unassigned YES unset administratively down down
Internal-Data0/0 unassigned YES unset up up
Internal-Data0/1 unassigned YES unset up up
Vlan1 192.168.1.1 YES CONFIG up up
Vlan2 192.168.11.2 YES CONFIG up up
Vlan3 unassigned YES manual up up*************************************************************
Virtual0 127.0.0.1 YES unset up up
ciscoasa# config t
ciscoasa(config)# int vlan 3
ciscoasa(config-if)# ip ad
ciscoasa(config-if)# ip address 192.168.12.2 255.255.255.0
ciscoasa(config-if)# end
ciscoasa# wr mem
Building configuration...
Cryptochecksum: 808baaba ced2a226 07cfb41f 9f6ec4f8
4608 bytes copied in 1.630 secs (4608 bytes/sec)
[OK]
ciscoasa# sh int ip brief
Interface IP-Address OK? Method Status Prot
ocol
Ethernet0/0 unassigned YES unset up up
Ethernet0/1 unassigned YES unset up up
Ethernet0/2 unassigned YES unset up up
Ethernet0/3 unassigned YES unset administratively down down
Ethernet0/4 unassigned YES unset administratively down down
Ethernet0/5 unassigned YES unset administratively down down
Ethernet0/6 unassigned YES unset administratively down down
Ethernet0/7 unassigned YES unset administratively down down
Internal-Data0/0 unassigned YES unset up up
Internal-Data0/1 unassigned YES unset up up
Vlan1 192.168.1.1 YES CONFIG up up
Vlan2 192.168.11.2 YES CONFIG up up
Vlan3 unassigned YES manual up up
Virtual0 127.0.0.1 YES unset up up
ciscoasa# sh ver
Cisco Adaptive Security Appliance Software Version 8.2(5)
Device Manager Version 6.4(9)
Compiled on Fri 20-May-11 16:00 by builders
System image file is "disk0:/asa825-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 3 days 17 hours
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.05
0: Int: Internal-Data0/0 : address is 001d.a24d.ed0e, irq 11
1: Ext: Ethernet0/0 : address is 001d.a24d.ed06, irq 255
2: Ext: Ethernet0/1 : address is 001d.a24d.ed07, irq 255
3: Ext: Ethernet0/2 : address is 001d.a24d.ed08, irq 255
4: Ext: Ethernet0/3 : address is 001d.a24d.ed09, irq 255
5: Ext: Ethernet0/4 : address is 001d.a24d.ed0a, irq 255
6: Ext: Ethernet0/5 : address is 001d.a24d.ed0b, irq 255
7: Ext: Ethernet0/6 : address is 001d.a24d.ed0c, irq 255
8: Ext: Ethernet0/7 : address is 001d.a24d.ed0d, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 10
Dual ISPs : Disabled
VLAN Trunk Ports : 0
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
<--- More --->
Need to know does this License support IP to 3rd vlan ?
Thanks
MaheshHi Julio,
I tried to config namef if but here is result
ciscoasa# sh run int vlan 3
interface Vlan3
description DMZ to 3550 New Switch
no nameif
security-level 50
ip address 192.168.12.2 255.255.255.0
ciscoasa# config t
ciscoasa(config)# int vlan 3
ciscoasa(config-if)# name
ciscoasa(config-if)# namei
ciscoasa(config-if)# nameif DMZ
ERROR: This license does not allow configuring more than 2 interfaces with
nameif and without a "no forward" command on this interface or on 1 interface(s)
with nameif already configured. -
Unable to access/lan2lan ping from VPN Fortigate to Cisco ASA 5505
Problem : Unable to access user A to user B
User A --- router A (122, fortigate 80c) --- (Site to Site VPN between fortigate & cisco asa) --- router B (93, cisco Asa 5505{in front asa got cisco800[81] before to internet} ) --- User B
After using wizard to configure the cisco ASA site to site VPN, the site-to-site tunnel is up.
Ping is unsuccessful from user A to user B
Ping is successful from user B to user A, data is accessable
After done the packet tracer from user A to user B,
Result :
Flow-lookup
Action : allow
Info: Found no matching flow, creating a new flow
Route-lookup
Action : allow
Info : 192.168.5.203 255.255.255.255 identity
Access-list
Action : drop
Config Implicit Rule
Result - The packet is dropped
Input Interface : inside
Output Interface : NP Identify Ifc
Info: (acl-drop)flow is denied by configured rule
Below is Cisco ASA 5505's show running-config
ASA Version 8.2(1)
hostname Asite
domain-name ssms1.com
enable password ZZZZ encrypted
passwd WWWW encrypted
names
name 82 B-firewall description Singapore office firewall
name 192.168.1.0 B-inside-subnet description Singapore office internal LAN IP
name 192.168.200.0 A-inside-VLAN12 description A-inside-VLAN12 (fortinet)
name 192.168.2.0 fw-inside-subnet description A office internal LAN IP
name 122 A-forti
interface Vlan1
nameif inside
security-level 100
ip address 192.168.5.203 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 93 255.255.255.240
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name ssms1.com
object-group network obj_any
network-object 0.0.0.0 0.0.0.0
access-list inside_nat0_outbound extended permit ip any 80 255.255.255.240
access-list inside_nat0_outbound extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
access-list outside_cryptomap extended permit ip fw-inside-subnet 255.255.255.0 B-inside-subnet 255.255.255.0
access-list Outside_nat-inbound extended permit ip A-inside-VLAN12 255.255.255.0 192.168.5.0 255.255.255.0
access-list Outside_nat-inbound extended permit ip host A-forti 192.168.5.0 255.255.255.0
access-list outside_1_cryptomap extended permit ip 192.168.5.0 255.255.255.0 A-inside-VLAN12 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-631.bin
no asdm history enable
arp timeout 14400
global (outside) 101 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 101 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 81 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http B-inside-subnet 255.255.255.0 inside
http fw-inside-subnet 255.255.255.0 inside
http 0.0.0.0 255.255.255.255 outside
http 0.0.0.0 0.0.0.0 outside
http 192.168.5.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer A-forti
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 2 match address outside_cryptomap
crypto map outside_map 2 set peer B-firewall
crypto map outside_map 2 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication pre-share
encryption aes-192
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash md5
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.5.10-192.168.5.20 inside
dhcpd dns 165 165 interface inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
username admin password XXX encrypted privilege 15
tunnel-group 122 type ipsec-l2l
tunnel-group 122 ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
class-map outside-class
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
message-length maximum client auto
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect icmp
policy-map outside-policy
description ok
class outside-class
inspect dns
inspect esmtp
inspect ftp
inspect h323 h225
inspect h323 ras
inspect icmp
inspect icmp error
inspect netbios
inspect rsh
inspect rtsp
inspect sip
inspect skinny
inspect sqlnet
inspect sunrpc
inspect tftp
inspect xdmcp
service-policy global_policy global
service-policy outside-policy interface outside
prompt hostname context
Cryptochecksum: XXX
: end
Kindly need your expertise&help to solve the problemany1 can help me ?
-
Cisco ASA 5505 config cleanup / revision
Hello all,
I have been assigned the task of "cleaning" up and revising one of our customer's ASA 5505. I am going through the config and I have some questions that I am hoping can be clarified for me. The config is rather simple with the inclusion of a remote-access VPN.
I am seeing the follwoing ACLs and Static PAT statements and I am wondering why the previous admin chose this design. IP address 192.168.0.6 is on of their MVbase (database) servers.
access-list acl_out extended permit tcp any interface outside eq 2043
access-list acl_out extended permit tcp any interface outside eq 2044
access-list acl_out extended permit udp any interface outside eq 2040
access-list acl_out extended permit udp any interface outside eq 2041
static (inside,outside) udp interface 2041 192.168.0.6 2041 netmask 255.255.255.255
static (inside,outside) udp interface 2043 192.168.0.6 2043 netmask 255.255.255.255
static (inside,outside) tcp interface 2043 192.168.0.6 2043 netmask 255.255.255.255
static (inside,outside) udp interface 2044 192.168.0.6 2044 netmask 255.255.255.255
static (inside,outside) tcp interface 2044 192.168.0.6 2044 netmask 255.255.255.255
Can I replace the following portion of the config with the one below it?
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA
ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto dynamic-map remote_map10 set transform-set ESP-AES-256-MD5
crypto map outside_map10 ipsec-isakmp dynamic remote_map
crypto map outside_map interface outside
crypto isakmp enable outside
I have attached the full ASA config in order for my questions to make more sense.
Thanks in advance,
AdrianDouglas,
In that case seems like there are many issues.
One thing I notized on the router is :
interface FastEthernet0/1.1
description vlan 1$FW_OUTSIDE$
interface FastEthernet0/1.10
description vlan 10$FW_INSIDE$
You can't have the same physical port for inside and outside.
Meaning this port can't be connected to the ASA and the PC or switch at the same time.
Try to find how far can the PC go; if it can ping the router and if the router can ping the ASA
Then on the ASA you have:
nat (inside) 1 0.0.0.0 0.0.0.0
But there is no global command, you need to add:
global (outside) 1 interface
You should be able to ping 192.168.1.1 from the ASA,
make sure Ethernet0/0 is up
Regards,
Felipe. -
Problems with basic config ASA 5505
new ASA 5505, tying to configure it, inside LAN is 192.168.2.x/23 (255.255.254.0). I connect to ASA5505 using ASDM ok when it is on the default 192.168.1.1. I change the ip on 'inside' vlan, and of course lose connection to it. It apparently doesn't totally save the info, though, because I can't connect to it using the new info. So, I made a vlan3, using port 0/2, using ip of 192.168.2.x/23 while connected to 192.168.1.1. Then I changed ip of my computer from 192.168.1.x to 192.168.2.x/23 but cannot even ping that port/ip on the ASA while connected to port 0/2. I switched computer back, and connected again to 192.168.1.1 and it does appear that my new settings for 0/2 are still there, so I'm not sure how to proceed? Thanks.
Sorry, had family emergency and was off for 2 weeks, then when came back had other work to catch up on.
Thanks for the reply. It would appear that the command you provided sets it back to default settings. I was able to set it back to default settings, but am now unsure as how to proceed to get the "inside" set to 192.168.2.0/23 and still be able to access it.
If I go back in, I can change "inside" to 192.168.2.1/23, but lose connection, so it "sort of" gets saved, in the respect that sometimes I can ping it, sometimes not. But can never connect to it.
Thanks, and sorry again about the delay. -
ASA 5505 unable to connect inside or outside
Hello,
I'm extremely new to router configurations, and am attempting to configure a backup ASA 5505 to use as a temporary access point in the event that our main ASA becomes unavailable. What I have done is loaded the running config from our main ASA onto the backup, and have made changes to necessary routes, IPs, etc. I can connect to it from a remote computer without problem, but I cannot access any of our servers, nor can I access the internet. I have also tried modifying the access list and NAT rules every which way from Sunday, but I still cannot get this thing to allow any information through. I keep getting "failed to locate egress interface for UDP from outside" errors.
We are using Cisco AnyConnect to connect , and mind you, since the config for this backup ASA was taken from our main, it still has the original certificate info and profiles. I was told that this wouldn't matter, but I thought I should mention in case I need to remove any of it from the config.
Here is part of the config file. I took out some information, but tried to keep it understandable. If anyone could point me in the right direction, it would be greatly appreciated!
ciscoasa# show running-config
: Saved
: Serial Number: xxxxxxxxxxx
: Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
ASA Version 9.2(2)
hostname ciscoasa
domain-name domain
enable password encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd encrypted
names
ip local pool pool1 x.x.9.22-x.x.9.254 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address x.x.8.10 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address x.x.x.237 255.255.255.248
boot system disk0:/asa922-k8.bin
boot config disk0:/startup-config
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns domain-lookup inside
dns domain-lookup outside
dns server-group Default
name-server x.x.8.100
domain-name domain
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network pool1
subnet x.x.9.0 255.255.255.0
object network outside-network
host x.x.x.237
object network Remote-Network
subnet x.x.8.0 255.255.255.0
object network local
object network obj-x.x.9.24
host x.x.9.24
object-group network Outside-Network-Group
description Outside Network Group
network-object x.x.x.232 255.255.255.248
object-group network Inside-Network-Group
description Inside Network Group
network-object x.x.8.0 255.255.255.0
access-list inside_access_in extended permit icmp any any
access-list inside_access_in extended permit ip any any
access-list NONAT extended permit ip x.x.8.0 255.255.255.0 x.x.9.0 255.255.255.0
pager lines 24
logging enable
logging buffer-size 30000
logging buffered debugging
logging asdm informational
no logging message 106015
no logging message 313001
no logging message 313008
no logging message 106023
no logging message 710003
no logging message 106100
no logging message 302015
no logging message 302014
no logging message 302013
no logging message 302018
no logging message 302017
no logging message 302016
no logging message 302021
no logging message 302020
flow-export destination inside x.x.8.132 2055
flow-export template timeout-rate 1
flow-export delay flow-create 50
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
asdm image disk0:/asdm-722.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside) source static any any destination static pool1 pool1 no-proxy-arp route-lookup
nat (inside,outside) source static any any destination static Remote-Network Remote-Network no-proxy-arp route-lookup
nat (outside,outside) source dynamic pool1 interface
object network obj_any
nat (inside,outside) dynamic interface
access-group inside_access_in in interface inside
route outside 0.0.0.0 0.0.0.0 x.x.x.232 1
route inside x.x.11.0 255.255.255.0 x.x.11.1 1
If you have any questions, or need any other information, please let me know.
Thanks!Am I posting this in the wrong section? Anyone?
-
Problem with ASA 5505 VPN config
Hi to all,
I have a problem with ASA 5505 remote access vpn. I have site-to-site VPN and I need that my VPN clients can access IP subnets that I have behind site-to-site VPN. All that I have tried I get and error to my log “Flow is a loopback”.
So what I need : for example I need that vpn client with ip 10.0.0.1 can go to 192.168.1.2
My config:
access-list Test_splitTunnelAcl standard permit host 10.0.2.3
access-list Test_splitTunnelAcl standard permit host 10.0.2.4
access-list Test_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list nonat_outside extended permit ip 10.0.0.0 255.255.255.0 192.168.1.0 255.255.255.0
ip local pool VPN_Client_Pool2 10.0.0.1-10.0.0.200 mask 255.255.255.0
nat (outside) 0 access-list nonat_outside
nat (outside) 1 10.0.0.0 255.255.255.0
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value Test_splitTunnelAcl
Site-to-Site:
crypto map outside_map 3 set peer 195.233.x.x
access-list outside_3_cryptomap extended permit ip object-group DM_INLINE_NETWORK_2 object-group DM_INLINE_NETWORK_4
object-group network DM_INLINE_NETWORK_2
network-object 10.0.2.0 255.255.255.0
network-object 10.0.3.0 255.255.255.0
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.2.70
network-object host 192.168.3.55
network-object 192.168.1.0 255.255.255.0
I hope that someone can post an answer and solve my problemA few things are required:
1) You don't need the following 2 lines, so it can be removed:
nat (outside) 0 access-list nonat_outside
nat (outside) 1 10.0.0.0 255.255.255.0
2) On the ASA, you need to configure:
same-security-traffic permit intra-interface
3) Object group: DM_INLINE_NETWORK_2 needs to include 10.0.0.0/24
4) On the remote lan-to-lan end, the crypto ACL also needs to include 10.0.0.0/24 as the destination subnet.
5) The NAT exemption (NONAT) on the remote lan-to-lan end also needs to include 10.0.0.0/24 as the destination subnet.
Hope that will resolve your problem. -
Unable to ping device behind Cisco 3750 on the same inside VLAN via Cisco ASA 5505 Anyconnect VPN
Hi Guys,
I've been stuck with this for the last 2 days, and I thought to try and use Cisco's forum, I setup my home DC, and started having problems once I moved a Cisco 5505 behind a Cisco 1841 router (I wanted to eventually test DMVPN live on the internet,) I was no longer able to ping some devices, then as soon as I introduce a collapsed core/distribution switch, I'm also no longer able to ping the devices behind the Cisco 3750, I've attached a network diagram and the ASA running-config.
Everything seem fine internally with the exception of an intermittent network connectivity with a Citrix NetScaler VPX running on a VMware ESXi.
For some odd reason, I am able to ping the following, with no issues.
Cisco 3750 SVI (192.168.1.3)
CentOS web server (connected directly to the Cisco ASA 5505)
I have checked and enable the following:
Nat Exemption
Sysopt connection permit-vpn
ACL's
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
Added ICMP in the inspection policy
Packet-capture - Only getting echo requests.
Thanks in advance!Hi,
I believe you have the problem with your no-nat configurations..... you to exempt NAT for the traffic from 172.16.10.0 (Anyconnect VPN pool) to 192.168.1.0/24 (Inside LAN) to make this work
object network acvpnpool
subnet <anyconnect VPN Subnet>
object network insidelan
subnet <inside lan subnet>
nat (inside,outside) source static acvpnpool acvpnpool destination static insidelan insidelan
Make sure that you are able to reach the GW/Inside ip adress of the firewall from LAN machine.... all routing in place properly..... Thanks!!!
Regards
Karthik -
Unable to establish site to site vpn between asa 5505 an 5510
Hi ALL expert
We are now plan to form a site to site IPSec VPN tunnel between ASA 5505 (ASA Version 8.4) and ASA 5510 (ASA Version 8.0) but failure, would you please teach me how to establish it? Any reference guide?
HugoHere are the links to the cisco config-guides:
http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/site2sit.html
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/vpn_site2site.html
In addition to VPN you need to look into NAT exemption:
http://www.cisco.com/en/US/docs/security/asa/asa80/configuration/guide/cfgnat.html#wp1043541
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/nat_overview.html#wpxref25608
http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/nat_rules.html#wp1232160
And lots of examples:
http://www.cisco.com/en/US/products/ps6120/prod_configuration_examples_list.html
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni -
Fairly new to cisco ASA 5505 - Can someone look through my config?
Hi.
Can some one tell me if I did the NAT part right? Both dynamic and static.
To be able to reach one vlan from another I created a Nat between them, is this the right way to do it?
I can still limit the access between the vlans based on the access list.
I also getting slow throughput over the VPN tunnel. Is there something wrong with my config. I used the wizard to set it up. There is also a cisco asa5505 on the other end.
If there is some thing else that seems wrong, please let me know.
Any help would be greatfully appreciated!
Config:
: Saved
ASA Version 7.2(2)
hostname ciscoasa
domain-name default.domain.invalid
enable password x encrypted
names
name 192.168.1.250 DomeneServer
name 192.168.1.10 NotesServer
name 192.168.1.90 OvServer
name 192.168.1.97 TerminalServer
name 192.168.1.98 w8-eyeshare
name 192.168.50.10 w8-print
name 192.168.1.94 w8-app
name 192.168.1.89 FonnaFlyMedia
interface Vlan1
nameif Vlan1
security-level 100
ip address 192.168.200.100 255.255.255.0
ospf cost 10
interface Vlan2
nameif outside
security-level 0
ip address 79.x.x.226 255.255.255.224
ospf cost 10
interface Vlan400
nameif vlan400
security-level 100
ip address 192.168.1.1 255.255.255.0
ospf cost 10
interface Vlan450
nameif Vlan450
security-level 100
ip address 192.168.210.1 255.255.255.0
ospf cost 10
interface Vlan460
nameif Vlan460-SuldalHotell
security-level 100
ip address 192.168.2.1 255.255.255.0
ospf cost 10
interface Vlan461
nameif Vlan461-SuldalHotellGjest
security-level 100
ip address 192.168.3.1 255.255.255.0
ospf cost 10
interface Vlan462
nameif Vlan462-Suldalsposten
security-level 100
ip address 192.168.4.1 255.255.255.0
ospf cost 10
interface Vlan470
nameif vlan470-Kyrkjekontoret
security-level 100
ip address 192.168.202.1 255.255.255.0
ospf cost 10
interface Vlan480
nameif vlan480-Telefoni
security-level 100
ip address 192.168.20.1 255.255.255.0
ospf cost 10
interface Vlan490
nameif Vlan490-QNapBackup
security-level 100
ip address 192.168.10.1 255.255.255.0
ospf cost 10
interface Vlan500
nameif Vlan500-HellandBadlands
security-level 100
ip address 192.168.30.1 255.255.255.0
ospf cost 10
interface Vlan510
nameif Vlan510-IsTak
security-level 100
ip address 192.168.40.1 255.255.255.0
ospf cost 10
interface Vlan600
nameif Vlan600-SafeQ
security-level 100
ip address 192.168.50.1 255.255.255.0
ospf cost 10
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
switchport access vlan 500
switchport trunk allowed vlan 400,450,460-462,470,480,500,510,600,610
switchport mode trunk
interface Ethernet0/3
switchport access vlan 490
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd x encrypted
ftp mode passive
clock timezone WAT 1
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group service Lotus_Notes_Utgaaande tcp
description Frim Notes og ut til alle
port-object eq domain
port-object eq ftp
port-object eq www
port-object eq https
port-object eq lotusnotes
port-object eq pop3
port-object eq pptp
port-object eq smtp
object-group service Lotus_Notes_inn tcp
description From alle og inn til Notes
port-object eq www
port-object eq lotusnotes
port-object eq pop3
port-object eq smtp
object-group service Reisebyraa tcp-udp
port-object range 3702 3702
port-object range 5500 5500
port-object range 9876 9876
object-group service Remote_Desktop tcp-udp
description Tilgang til Remote Desktop
port-object range 3389 3389
object-group service Sand_Servicenter_50000 tcp-udp
description Program tilgang til Sand Servicenter AS
port-object range 50000 50000
object-group service VNC_Remote_Admin tcp
description Frå oss til alle
port-object range 5900 5900
object-group service Printer_Accept tcp-udp
port-object range 9100 9100
port-object eq echo
object-group icmp-type Echo_Ping
icmp-object echo
icmp-object echo-reply
object-group service Print tcp
port-object range 9100 9100
object-group service FTP_NADA tcp
description Suldalsposten NADA tilgang
port-object eq ftp
port-object eq ftp-data
object-group service Telefonsentral tcp
description Hoftun
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
port-object eq telnet
object-group service Printer_inn_800 tcp
description Fra 800 nettet og inn til 400 port 7777
port-object range 7777 7777
object-group service Suldalsposten tcp
description Sending av mail vha Mac Mail programmet - åpner smtp
port-object eq pop3
port-object eq smtp
object-group service http2 tcp
port-object range 81 81
object-group service DMZ_FTP_PASSIVE tcp-udp
port-object range 55536 56559
object-group service DMZ_FTP tcp-udp
port-object range 20 21
object-group service DMZ_HTTPS tcp-udp
port-object range 443 443
object-group service DMZ_HTTP tcp-udp
port-object range 8080 8080
object-group service DNS_Query tcp
port-object range domain domain
object-group service DUETT_SQL_PORT tcp-udp
description For kobling mellom andre nett og duett server
port-object range 54659 54659
access-list outside_access_in extended permit ip any any
access-list outside_access_out extended permit ip any any
access-list vlan400_access_in extended deny ip any host 149.20.56.34
access-list vlan400_access_in extended deny ip any host 149.20.56.32
access-list vlan400_access_in extended permit ip any any
access-list Vlan450_access_in extended deny ip any host 149.20.56.34
access-list Vlan450_access_in extended deny ip any host 149.20.56.32
access-list Vlan450_access_in extended permit ip any any
access-list Vlan460_access_in extended deny ip any host 149.20.56.34
access-list Vlan460_access_in extended deny ip any host 149.20.56.32
access-list Vlan460_access_in extended permit ip any any
access-list vlan400_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_Utgaaande
access-list vlan400_access_out extended permit tcp any host DomeneServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host TerminalServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host OvServer object-group http2
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Lotus_Notes_inn
access-list vlan400_access_out extended permit tcp any host NotesServer object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-eyeshare object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host w8-app object-group Remote_Desktop
access-list vlan400_access_out extended permit tcp any host FonnaFlyMedia range 8400 8600
access-list vlan400_access_out extended permit udp any host FonnaFlyMedia range 9000 9001
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host DomeneServer
access-list vlan400_access_out extended permit tcp 192.168.4.0 255.255.255.0 host w8-app object-group DUETT_SQL_PORT
access-list Vlan500_access_in extended deny ip any host 149.20.56.34
access-list Vlan500_access_in extended deny ip any host 149.20.56.32
access-list Vlan500_access_in extended permit ip any any
access-list vlan470_access_in extended deny ip any host 149.20.56.34
access-list vlan470_access_in extended deny ip any host 149.20.56.32
access-list vlan470_access_in extended permit ip any any
access-list Vlan490_access_in extended deny ip any host 149.20.56.34
access-list Vlan490_access_in extended deny ip any host 149.20.56.32
access-list Vlan490_access_in extended permit ip any any
access-list Vlan450_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan1_access_out extended permit ip any any
access-list Vlan1_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan1_access_out extended deny ip any any
access-list Vlan1_access_out extended permit icmp any any echo-reply
access-list Vlan460_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit icmp any any object-group Echo_Ping
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_FTP_PASSIVE
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTPS
access-list Vlan490_access_out extended permit tcp any host 192.168.10.10 object-group DMZ_HTTP
access-list Vlan500_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan470_access_out extended permit tcp any host 192.168.202.10 object-group Remote_Desktop
access-list Vlan510_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan480_access_out extended permit ip any any
access-list Vlan510_access_in extended permit ip any any
access-list Vlan600_access_in extended permit ip any any
access-list Vlan600_access_out extended permit icmp any any
access-list Vlan600_access_out extended permit tcp any host w8-print object-group Remote_Desktop
access-list Vlan600_access_out extended permit tcp 192.168.1.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.202.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_out extended permit tcp 192.168.210.0 255.255.255.0 host w8-print eq www
access-list Vlan600_access_in_1 extended permit ip any any
access-list Vlan461_access_in extended permit ip any any
access-list Vlan461_access_out extended permit icmp any any object-group Echo_Ping
access-list vlan400_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap_1 extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list outside_20_cryptomap extended permit ip 192.168.1.0 255.255.255.0 192.168.77.0 255.255.255.0
access-list Vlan462-Suldalsposten_access_in extended permit ip any any
access-list Vlan462-Suldalsposten_access_out extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_out_1 extended permit icmp any any echo-reply
access-list Vlan462-Suldalsposten_access_in_1 extended permit ip any any
pager lines 24
logging enable
logging asdm informational
mtu Vlan1 1500
mtu outside 1500
mtu vlan400 1500
mtu Vlan450 1500
mtu Vlan460-SuldalHotell 1500
mtu Vlan461-SuldalHotellGjest 1500
mtu vlan470-Kyrkjekontoret 1500
mtu vlan480-Telefoni 1500
mtu Vlan490-QNapBackup 1500
mtu Vlan500-HellandBadlands 1500
mtu Vlan510-IsTak 1500
mtu Vlan600-SafeQ 1500
mtu Vlan462-Suldalsposten 1500
no failover
monitor-interface Vlan1
monitor-interface outside
monitor-interface vlan400
monitor-interface Vlan450
monitor-interface Vlan460-SuldalHotell
monitor-interface Vlan461-SuldalHotellGjest
monitor-interface vlan470-Kyrkjekontoret
monitor-interface vlan480-Telefoni
monitor-interface Vlan490-QNapBackup
monitor-interface Vlan500-HellandBadlands
monitor-interface Vlan510-IsTak
monitor-interface Vlan600-SafeQ
monitor-interface Vlan462-Suldalsposten
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (vlan400) 0 access-list vlan400_nat0_outbound
nat (vlan400) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan450) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan460-SuldalHotell) 1 0.0.0.0 0.0.0.0
nat (Vlan461-SuldalHotellGjest) 1 0.0.0.0 0.0.0.0
nat (vlan470-Kyrkjekontoret) 1 0.0.0.0 0.0.0.0
nat (Vlan490-QNapBackup) 1 0.0.0.0 0.0.0.0 dns
nat (Vlan500-HellandBadlands) 1 0.0.0.0 0.0.0.0
nat (Vlan510-IsTak) 1 0.0.0.0 0.0.0.0
nat (Vlan600-SafeQ) 1 0.0.0.0 0.0.0.0
nat (Vlan462-Suldalsposten) 1 0.0.0.0 0.0.0.0
static (vlan400,outside) 79.x.x.x DomeneServer netmask 255.255.255.255
static (vlan470-Kyrkjekontoret,outside) 79.x.x.x 192.168.202.10 netmask 255.255.255.255
static (vlan400,outside) 79.x.x.x NotesServer netmask 255.255.255.255 dns
static (vlan400,outside) 79.x.x.231 TerminalServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.234 OvServer netmask 255.255.255.255
static (vlan400,outside) 79.x.x.232 w8-eyeshare netmask 255.255.255.255
static (Vlan490-QNapBackup,outside) 79.x.x.233 192.168.10.10 netmask 255.255.255.255 dns
static (Vlan600-SafeQ,outside) 79.x.x.235 w8-print netmask 255.255.255.255
static (vlan400,outside) 79.x.x.236 w8-app netmask 255.255.255.255
static (Vlan450,vlan400) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (Vlan500-HellandBadlands,vlan400) 192.168.30.0 192.168.30.0 netmask 255.255.255.0
static (vlan400,Vlan500-HellandBadlands) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan450) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,outside) 79.x.x.252 FonnaFlyMedia netmask 255.255.255.255
static (Vlan462-Suldalsposten,vlan400) 192.168.4.0 192.168.4.0 netmask 255.255.255.0
static (vlan400,Vlan462-Suldalsposten) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (vlan400,Vlan600-SafeQ) 192.168.1.0 192.168.1.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan400) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,Vlan450) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan600-SafeQ,vlan470-Kyrkjekontoret) 192.168.50.0 192.168.50.0 netmask 255.255.255.0
static (Vlan450,Vlan600-SafeQ) 192.168.210.0 192.168.210.0 netmask 255.255.255.0
static (vlan470-Kyrkjekontoret,Vlan600-SafeQ) 192.168.202.0 192.168.202.0 netmask 255.255.255.0
access-group Vlan1_access_out out interface Vlan1
access-group outside_access_in in interface outside
access-group outside_access_out out interface outside
access-group vlan400_access_in in interface vlan400
access-group vlan400_access_out out interface vlan400
access-group Vlan450_access_in in interface Vlan450
access-group Vlan450_access_out out interface Vlan450
access-group Vlan460_access_in in interface Vlan460-SuldalHotell
access-group Vlan460_access_out out interface Vlan460-SuldalHotell
access-group Vlan461_access_in in interface Vlan461-SuldalHotellGjest
access-group Vlan461_access_out out interface Vlan461-SuldalHotellGjest
access-group vlan470_access_in in interface vlan470-Kyrkjekontoret
access-group vlan470_access_out out interface vlan470-Kyrkjekontoret
access-group vlan480_access_out out interface vlan480-Telefoni
access-group Vlan490_access_in in interface Vlan490-QNapBackup
access-group Vlan490_access_out out interface Vlan490-QNapBackup
access-group Vlan500_access_in in interface Vlan500-HellandBadlands
access-group Vlan500_access_out out interface Vlan500-HellandBadlands
access-group Vlan510_access_in in interface Vlan510-IsTak
access-group Vlan510_access_out out interface Vlan510-IsTak
access-group Vlan600_access_in_1 in interface Vlan600-SafeQ
access-group Vlan600_access_out out interface Vlan600-SafeQ
access-group Vlan462-Suldalsposten_access_in_1 in interface Vlan462-Suldalsposten
access-group Vlan462-Suldalsposten_access_out_1 out interface Vlan462-Suldalsposten
route outside 0.0.0.0 0.0.0.0 79.x.x.225 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
username x password x encrypted privilege 15
aaa authentication ssh console LOCAL
http server enable
http 192.168.210.0 255.255.255.0 Vlan450
http 192.168.200.0 255.255.255.0 Vlan1
http 192.168.1.0 255.255.255.0 vlan400
no snmp-server location
no snmp-server contact
snmp-server community public
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto map outside_map 20 match address outside_20_cryptomap_1
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer 62.92.159.137
crypto map outside_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp enable vlan400
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
tunnel-group 62.92.159.137 type ipsec-l2l
tunnel-group 62.92.159.137 ipsec-attributes
pre-shared-key *
telnet 192.168.200.0 255.255.255.0 Vlan1
telnet 192.168.1.0 255.255.255.0 vlan400
telnet timeout 5
ssh 171.68.225.216 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd update dns both
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan1
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface outside
dhcpd address 192.168.1.100-192.168.1.225 vlan400
dhcpd option 6 ip DomeneServer 81.167.36.11 interface vlan400
dhcpd option 3 ip 192.168.1.1 interface vlan400
dhcpd enable vlan400
dhcpd address 192.168.210.100-192.168.210.200 Vlan450
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan450
dhcpd option 3 ip 192.168.210.1 interface Vlan450
dhcpd enable Vlan450
dhcpd address 192.168.2.100-192.168.2.150 Vlan460-SuldalHotell
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan460-SuldalHotell
dhcpd option 3 ip 192.168.2.1 interface Vlan460-SuldalHotell
dhcpd enable Vlan460-SuldalHotell
dhcpd address 192.168.3.100-192.168.3.200 Vlan461-SuldalHotellGjest
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan461-SuldalHotellGjest
dhcpd option 3 ip 192.168.3.1 interface Vlan461-SuldalHotellGjest
dhcpd enable Vlan461-SuldalHotellGjest
dhcpd address 192.168.202.100-192.168.202.199 vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.202.1 interface vlan470-Kyrkjekontoret
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan470-Kyrkjekontoret
dhcpd enable vlan470-Kyrkjekontoret
dhcpd option 3 ip 192.168.20.1 interface vlan480-Telefoni
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface vlan480-Telefoni
dhcpd address 192.168.10.80-192.168.10.90 Vlan490-QNapBackup
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan490-QNapBackup
dhcpd option 3 ip 192.168.10.1 interface Vlan490-QNapBackup
dhcpd address 192.168.30.100-192.168.30.199 Vlan500-HellandBadlands
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan500-HellandBadlands
dhcpd option 3 ip 192.168.30.1 interface Vlan500-HellandBadlands
dhcpd enable Vlan500-HellandBadlands
dhcpd address 192.168.40.100-192.168.40.150 Vlan510-IsTak
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan510-IsTak
dhcpd option 3 ip 192.168.40.1 interface Vlan510-IsTak
dhcpd enable Vlan510-IsTak
dhcpd address 192.168.50.150-192.168.50.199 Vlan600-SafeQ
dhcpd option 6 ip 81.167.36.3 81.167.36.11 interface Vlan600-SafeQ
dhcpd enable Vlan600-SafeQ
dhcpd address 192.168.4.100-192.168.4.150 Vlan462-Suldalsposten
dhcpd option 6 ip DomeneServer 81.167.36.11 interface Vlan462-Suldalsposten
dhcpd option 3 ip 192.168.4.1 interface Vlan462-Suldalsposten
dhcpd enable Vlan462-Suldalsposten
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
prompt hostname context
Cryptochecksum:x
: endI was just wondering if this is the way to do the "connection" between vlans.. or should it be routed?
The traffic between the vlan is working as intended. There are not much traffice only some RDP connection and some printing jobs.
But i'm getting some of these errors: (not alle like this, but portmap translation creation failed)
305006 192.168.10.200 portmap translation creation failed for udp src Vlan460-SuldalHotell:192.168.2.112/59133 dst Vlan490-QNapBackup:192.168.10.200/161
I did the sh interface commends:
Result of the command: "sh interface"
Interface Vlan1 "Vlan1", is down, line protocol is down
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.200.100, subnet mask 255.255.255.0
Traffic Statistics for "Vlan1":
0 packets input, 0 bytes
0 packets output, 0 bytes
0 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 79.x.x.226, subnet mask 255.255.255.224
Traffic Statistics for "outside":
1780706730 packets input, 1221625431570 bytes
1878320718 packets output, 1743030863134 bytes
5742216 packets dropped
1 minute input rate 558 pkts/sec, 217568 bytes/sec
1 minute output rate 803 pkts/sec, 879715 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 621 pkts/sec, 482284 bytes/sec
5 minute output rate 599 pkts/sec, 428957 bytes/sec
5 minute drop rate, 1 pkts/sec
Interface Vlan400 "vlan400", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.1.1, subnet mask 255.255.255.0
Traffic Statistics for "vlan400":
1093422654 packets input, 1191121436317 bytes
784209789 packets output, 374041914789 bytes
11465163 packets dropped
1 minute input rate 751 pkts/sec, 870445 bytes/sec
1 minute output rate 462 pkts/sec, 116541 bytes/sec
1 minute drop rate, 11 pkts/sec
5 minute input rate 474 pkts/sec, 415304 bytes/sec
5 minute output rate 379 pkts/sec, 197861 bytes/sec
5 minute drop rate, 7 pkts/sec
Interface Vlan450 "Vlan450", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.210.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan450":
139711812 packets input, 27519985266 bytes
202793062 packets output, 233679075458 bytes
12523100 packets dropped
1 minute input rate 68 pkts/sec, 9050 bytes/sec
1 minute output rate 83 pkts/sec, 88025 bytes/sec
1 minute drop rate, 6 pkts/sec
5 minute input rate 145 pkts/sec, 15068 bytes/sec
5 minute output rate 241 pkts/sec, 287093 bytes/sec
5 minute drop rate, 6 pkts/sec
Interface Vlan460 "Vlan460-SuldalHotell", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.2.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan460-SuldalHotell":
177971988 packets input, 161663208458 bytes
193137004 packets output, 137418896469 bytes
4003957 packets dropped
1 minute input rate 13 pkts/sec, 2295 bytes/sec
1 minute output rate 14 pkts/sec, 15317 bytes/sec
1 minute drop rate, 2 pkts/sec
5 minute input rate 4 pkts/sec, 794 bytes/sec
5 minute output rate 1 pkts/sec, 477 bytes/sec
5 minute drop rate, 2 pkts/sec
Interface Vlan461 "Vlan461-SuldalHotellGjest", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.3.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan461-SuldalHotellGjest":
332909692 packets input, 351853184942 bytes
312038518 packets output, 156669956740 bytes
583171 packets dropped
1 minute input rate 0 pkts/sec, 6 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 6 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan462 "Vlan462-Suldalsposten", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.4.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan462-Suldalsposten":
33905 packets input, 14303320 bytes
28285 packets output, 27536357 bytes
10199 packets dropped
1 minute input rate 0 pkts/sec, 6 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 6 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan470 "vlan470-Kyrkjekontoret", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.202.1, subnet mask 255.255.255.0
Traffic Statistics for "vlan470-Kyrkjekontoret":
12176257 packets input, 4305665570 bytes
10618750 packets output, 5982598969 bytes
974796 packets dropped
1 minute input rate 2 pkts/sec, 770 bytes/sec
1 minute output rate 1 pkts/sec, 861 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 2 pkts/sec, 708 bytes/sec
5 minute output rate 1 pkts/sec, 980 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan480 "vlan480-Telefoni", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.20.1, subnet mask 255.255.255.0
Traffic Statistics for "vlan480-Telefoni":
246638 packets input, 43543149 bytes
10 packets output, 536 bytes
226674 packets dropped
1 minute input rate 0 pkts/sec, 126 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 56 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan490 "Vlan490-QNapBackup", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.10.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan490-QNapBackup":
137317833 packets input, 6066713912 bytes
223933623 packets output, 263191563744 bytes
531738 packets dropped
1 minute input rate 0 pkts/sec, 135 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 68 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan500 "Vlan500-HellandBadlands", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.30.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan500-HellandBadlands":
30816778 packets input, 4887486069 bytes
42403099 packets output, 47831750415 bytes
948717 packets dropped
1 minute input rate 3 pkts/sec, 707 bytes/sec
1 minute output rate 3 pkts/sec, 3459 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 23 bytes/sec
5 minute output rate 0 pkts/sec, 31 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan510 "Vlan510-IsTak", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.40.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan510-IsTak":
1253148 packets input, 245364736 bytes
1225385 packets output, 525528101 bytes
161567 packets dropped
1 minute input rate 0 pkts/sec, 6 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 6 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Vlan600 "Vlan600-SafeQ", is up, line protocol is up
Hardware is EtherSVI
MAC address 001d.453a.ea0e, MTU 1500
IP address 192.168.50.1, subnet mask 255.255.255.0
Traffic Statistics for "Vlan600-SafeQ":
1875377 packets input, 1267279709 bytes
1056139 packets output, 290728055 bytes
521943 packets dropped
1 minute input rate 0 pkts/sec, 165 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 178 bytes/sec
5 minute output rate 0 pkts/sec, 9 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001d.453a.ea06, MTU not set
IP address unassigned
1782670655 packets input, 1256666911856 bytes, 0 no buffer
Received 95709 broadcasts, 0 runts, 0 giants
1978 input errors, 1978 CRC, 0 frame, 0 overrun, 1978 ignored, 0 abort
0 L2 decode drops
17179928790 switch ingress policy drops
1878320261 packets output, 1778955488577 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Interface Ethernet0/2 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001d.453a.ea08, MTU not set
IP address unassigned
1790819459 packets input, 1783854920873 bytes, 0 no buffer
Received 27571913 broadcasts, 0 runts, 0 giants
614 input errors, 614 CRC, 0 frame, 0 overrun, 614 ignored, 0 abort
0 L2 decode drops
19768 switch ingress policy drops
1547507675 packets output, 991527977853 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Interface Ethernet0/3 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001d.453a.ea09, MTU not set
IP address unassigned
137318166 packets input, 9176625008 bytes, 0 no buffer
Received 290030 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
335 switch ingress policy drops
223933623 packets output, 267222625073 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops -
ASA 5505: unable to ping external hosts
Hi,
I have a LAN behind ASA 5505, interface NAT/PAT is configured.
External interface is configured for PPPoE.
Everything works fine except I cannot ping from a LAN PC external hosts. I can however ping external hosts from ASA itself. ICMP is allowed:
icmp permit any inside
icmp permit any outside
access-list outside_access_in extended permit icmp any any
Protocol inspections and fixups are default.
When I ping an external host 61.95.50.185 from the LAN host 10.2.32.68 I am getting the following in the log:
302020 61.95.50.185 10.2.32.68 Built ICMP connection for faddr 61.95.50.185/0 gaddr 202.xx.yy.zz/1 laddr 10.2.32.68/512
302020 61.95.50.185 202.xx.yy.zz Built ICMP connection for faddr 61.95.50.185/0 gaddr 202.xx.yy.zz/1 laddr 202.xx.yy.zz/1
313004 Denied ICMP type=0, from laddr 61.95.50.185 on interface outside to 202.xx.yy.zz: no matching session
313001 61.95.50.185 Denied ICMP type=0, code=0 from 61.95.50.185 on interface outside
302021 61.95.50.185 202.xx.yy.zz Teardown ICMP connection for faddr 61.95.50.185/0 gaddr 202.xx.yy.zz/1 laddr 202.xx.yy.zz/1
302021 61.95.50.185 10.2.32.68 Teardown ICMP connection for faddr 61.95.50.185/0 gaddr 202.xx.yy.zz/1 laddr 10.2.32.68/512
Where 202.xx.yy.zz is IP of external interface of ASA.
This is a very simple setup that runs on a number of othe PIXes/ASAs and pings to external IP normally work just fine. I can't understand why ping replies are getting dropped on the interface?
Any help will be highly appreciated.
Thank you.
AlexAlex / Kerry, you have couple of options for handling icmp outbound, either acl or icmp inspection :
access-list outside_access_in extended permit icmp any any echo-reply
access-list outside_access_in extended permit icmp any any source-quench
access-list outside_access_in extended permit icmp any any unreachable
access-list outside_access_in extended permit icmp any any time-exceeded
access-group outside_access_in in interface outside
or icmp inspection instead of acl.
policy-map global_policy
class inspection_default
inspect icmp
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a0080094e8a.shtml
HTH
Jorge -
Internet Connection Became Slow after Introduction of Cisco ASA 5505 to the Network
I configured a Cisco ASA 5505 (Version Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
in transparent firewall mode and inserted after Cisco 1700 router. However, the internet connection became very slow and users are compaining that they cannot load any pages.
My setup looks like:
Internet --> Cisco 1700 --> Cisco ASA 5505 --> LAN
The license information is:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
My running-config looks like:
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Vlan1
nameif inside
security-level 100
no shut
interface Vlan2
nameif outside
security-level 0
no shut
interface Ethernet0/0
switchport access vlan 2
no shut
interface Ethernet0/1
no shut
interface Ethernet0/2
no shut
interface Ethernet0/3
no shut
interface Ethernet0/4
no shut
interface Ethernet0/5
no shut
interface Ethernet0/6
no shut
interface Ethernet0/7
no shut
passwd 2KFQnbNIdI.2KYOU encrypted
regex urllist1 ".*\.([Ee][Xx][Ee]|[Cc][Oo][Mm]|[Bb][Aa][Tt]) HTTP/1.[01]"
regex urllist2 ".*\.([Pp][Ii][Ff]|[Vv][Bb][Ss]|[Ww][Ss][Hh]) HTTP/1.[01]"
regex urllist3 ".*\.([Dd][Oo][Cc]|[Xx][Ll][Ss]|[Pp][Pp][Tt]) HTTP/1.[01]"
regex urllist4 ".*\.([Zz][Ii][Pp]|[Tt][Aa][Rr]|[Tt][Gg][Zz]) HTTP/1.[01]"
regex domainlist1 "\.facebook\.com"
regex domainlist2 "\.diretube\.com"
regex domainlist3 "\.youtube\.com"
regex domainlist4 "\.vimeo\.com"
regex applicationheader "application/.*"
regex contenttype "Content-Type"
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_in extended permit ip any any
access-list inside_mpc extended permit tcp any any eq www
access-list inside_mpc extended permit tcp any any eq 8080
pager lines 24
mtu outside 1500
mtu inside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domainlist1
match regex domainlist2
match regex domainlist3
match regex domainlist4
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map type regex match-any URLBlockList
match regex urllist1
match regex urllist2
match regex urllist3
match regex urllist4
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all AppHeaderClass
match response header regex contenttype regex applicationheader
class-map httptraffic
match access-list inside_mpc
class-map type inspect http match-all BlockURLsClass
match request uri regex class URLBlockList
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action drop-connection
class AppHeaderClass
drop-connection log
match request method connect
drop-connection log
class BlockDomainsClass
reset log
class BlockURLsClass
reset log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
policy-map inside-policy
class httptraffic
inspect http http_inspection_policy
service-policy global_policy global
service-policy inside-policy interface inside
prompt hostname context
Cryptochecksum:8ab1a53df6ae3c202aee236d6080edfd
: end
Could the slow internet connection be due to license limitations? Or is there something wrong with my configuration?
Please see the configuration and help.
ThanksI have re-configured the ASA 5505 yesterday and so far it's working fine. I am not sure if the problem will re-appear later on. Anyways here is my sh tech-support
ciscoasa# sh tech-support
Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
Compiled on Wed 15-Aug-07 16:08 by builders
System image file is "disk0:/asa723-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 14 hours 16 mins
Hardware: ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0 : address is 001f.9ee8.ffa2, irq 11
1: Ext: Ethernet0/0 : address is 001f.9ee8.ff9a, irq 255
2: Ext: Ethernet0/1 : address is 001f.9ee8.ff9b, irq 255
3: Ext: Ethernet0/2 : address is 001f.9ee8.ff9c, irq 255
4: Ext: Ethernet0/3 : address is 001f.9ee8.ff9d, irq 255
5: Ext: Ethernet0/4 : address is 001f.9ee8.ff9e, irq 255
6: Ext: Ethernet0/5 : address is 001f.9ee8.ff9f, irq 255
<--- More --->
7: Ext: Ethernet0/6 : address is 001f.9ee8.ffa0, irq 255
8: Ext: Ethernet0/7 : address is 001f.9ee8.ffa1, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 3, DMZ Restricted
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
VPN Peers : 10
WebVPN Peers : 2
Dual ISPs : Disabled
VLAN Trunk Ports : 0
This platform has a Base license.
Serial Number: JMX1211Z2N4
Running Activation Key: 0xaf0ed046 0xbcf18ebf 0x80b38508 0xba785cc0 0x05250493
Configuration register is 0x1
Configuration has not been modified since last system restart.
<--- More --->
------------------ show clock ------------------
18:32:58.254 UTC Tue Nov 26 2013
------------------ show memory ------------------
Free memory: 199837144 bytes (74%)
Used memory: 68598312 bytes (26%)
Total memory: 268435456 bytes (100%)
------------------ show conn count ------------------
1041 in use, 2469 most used
------------------ show xlate count ------------------
0 in use, 0 most used
------------------ show blocks ------------------
SIZE MAX LOW CNT
0 100 68 100
<--- More --->
4 300 299 299
80 100 92 100
256 100 94 100
1550 6174 6166 6174
2048 1124 551 612
------------------ show blocks queue history detail ------------------
History buffer memory usage: 2136 bytes (default)
------------------ show interface ------------------
Interface Internal-Data0/0 "", is up, line protocol is up
Hardware is y88acs06, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 001f.9ee8.ffa2, MTU not set
IP address unassigned
18491855 packets input, 11769262614 bytes, 0 no buffer
Received 213772 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops, 0 demux drops
18185861 packets output, 11626494317 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 late collisions, 0 deferred
<--- More --->
0 input reset drops, 0 output reset drops
input queue (curr/max packets): hardware (0/0) software (0/0)
output queue (curr/max packets): hardware (0/55) software (0/0)
Control Point Interface States:
Interface number is unassigned
Interface Internal-Data0/1 "", is administratively down, line protocol is up
Hardware is 88E6095, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 0000.0003.0002, MTU not set
IP address unassigned
18184216 packets input, 11625360131 bytes, 0 no buffer
Received 206655 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 switch ingress policy drops
18490057 packets output, 11768078777 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Loopback0 "_internal_loopback", is up, line protocol is up
Hardware is VirtualMAC address 0000.0000.0000, MTU 1500
IP address 127.1.0.1, subnet mask 255.255.0.0
<--- More --->
Traffic Statistics for "_internal_loopback":
1 packets input, 28 bytes
1 packets output, 28 bytes
1 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 28
Interface config status is active
Interface state is active
Interface Vlan1 "inside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa2, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "inside":
7742275 packets input, 903584114 bytes
10645034 packets output, 10347291114 bytes
184883 packets dropped
1 minute input rate 320 pkts/sec, 35404 bytes/sec
1 minute output rate 325 pkts/sec, 313317 bytes/sec
<--- More --->
1 minute drop rate, 17 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
Control Point Interface States:
Interface number is 1
Interface config status is active
Interface state is active
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa3, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "outside":
10750090 packets input, 10432619059 bytes
7541331 packets output, 870613684 bytes
109911 packets dropped
1 minute input rate 328 pkts/sec, 313770 bytes/sec
1 minute output rate 301 pkts/sec, 32459 bytes/sec
1 minute drop rate, 2 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
Control Point Interface States:
Interface number is 2
<--- More --->
Interface config status is active
Interface state is active
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001f.9ee8.ff9a, MTU not set
IP address unassigned
10749794 packets input, 10630700889 bytes, 0 no buffer
Received 2506 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
3 switch ingress policy drops
7541070 packets output, 1028190148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/1 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
<--- More --->
Available but not configured via nameif
MAC address 001f.9ee8.ff9b, MTU not set
IP address unassigned
7741977 packets input, 1064586806 bytes, 0 no buffer
Received 211282 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
10644663 packets output, 10543362751 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/2 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9c, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
<--- More --->
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/3 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9d, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/4 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9e, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
<--- More --->
Interface number is unassigned
Interface Ethernet0/5 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9f, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/6 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
<--- More --->
MAC address 001f.9ee8.ffa0, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/7 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ffa1, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
------------------ show cpu usage ------------------
CPU utilization for 5 seconds = 12%; 1 minute: 11%; 5 minutes: 11%
------------------ show cpu hogging process ------------------
Process: Dispatch Unit, NUMHOG: 1, MAXHOG: 133, LASTHOG: 140
LASTHOG At: 04:45:59 UTC Nov 26 2013
PC: 8be0f7
Traceback: 8bed19 8bf553 302b87 3030a5 2fad69 7674bf 75ca16
c6251d c62a4c c62f6c 75c653 767820 797f64 769c85
<--- More --->
------------------ show process ------------------
PC SP STATE Runtime SBASE Stack Process
Mwe 00c9bb24 01bb8700 013e3250 0 01733fc8 15616/16384 emweb/cifs
Lwe 001072ac 0176f9c4 013e32d0 0 0176d9f0 8132/8192 block_diag
Mrd 00223a67 01783d5c 013e33b0 314854 0177be18 25752/32768 Dispatch Unit
Msi 00f82847 01b07b84 013e3250 229 01b05bc0 7984/8192 y88acs06 OneSec Thread
Mwe 0011b1a5 01b09cfc 013e3250 0 01b07d88 7864/8192 Reload Control Thread
Mwe 00120606 01b1260c 013e5258 0 01b10988 7256/8192 aaa
Mwe 001486aa 01b19404 013e5ae8 0 01b15450 16020/16384 CMGR Server Process
Mwe 0014c3c5 01b1b4d4 013e3250 0 01b19570 7968/8192 CMGR Timer Process
Lwe 002227a1 01b239b4 013ee360 0 01b219f0 7524/8192 dbgtrace
Mwe 004e1ba5 01b29c34 013e3250 157 01b27d50 6436/8192 eswilp_svi_init
Mwe 01064b1d 01b4a7f4 013e3250 0 01b48890 7848/8192 Chunk Manager
Msi 008b61b6 01b52d54 013e3250 230 01b50da0 7856/8192 PIX Garbage Collector
Lsi 00ecb6ac 01b54e94 013e3250 12 01b52ec0 7552/8192 route_process
Mwe 008a5ddc 01b5dc04 0133b430 0 01b5bc40 8116/8192 IP Address Assign
Mwe 00acb779 01b60604 01346e10 0 01b5e640 8116/8192 QoS Support Module
Mwe 0091eba9 01b6275c 0133c530 0 01b60798 8116/8192 Client Update Task
Lwe 01083c8e 01b656d4 013e3250 123088 01b63770 7840/8192 Checkheaps
Mwe 00acfd7d 01b6b824 013e3250 623 01b69ad0 3476/8192 Quack process
Mwe 00b2a260 01b6dad4 013e3250 22 01b6bbf0 7364/8192 Session Manager
Mwe 00c55efd 01b78564 031d0478 4 01b74a50 14768/16384 uauth
<--- More --->
Mwe 00be3c9e 01b7aaec 0135c010 0 01b78b28 7524/8192 Uauth_Proxy
Mwe 00c52759 01b80e0c 01361770 0 01b7ee88 7712/8192 SMTP
Mwe 00c3f7b9 01b82eec 01361710 0 01b80fa8 7412/8192 Logger
Mwe 00c3fd26 01b8502c 013e3250 0 01b830c8 7492/8192 Thread Logger
Mwe 00f62272 01b9596c 013ac520 0 01b939c8 7188/8192 vpnlb_thread
Msi 00b4097c 01c598c4 013e3250 190 01c578f0 8000/8192 emweb/cifs_timer
Msi 005bd338 017a909c 013e3250 25855 017a7108 7412/8192 arp_timer
Mwe 005c76bc 01b486e4 013fba50 20643 01b46770 7348/8192 arp_forward_thread
Mwe 00c5a919 023fa5fc 013619e0 0 023f8648 7968/8192 tcp_fast
Mwe 00c5a6e5 023fc624 013619e0 0 023fa670 7968/8192 tcp_slow
Mwe 00c754d1 0240d42c 013628a0 0 0240b478 8100/8192 udp_timer
Mwe 0019cb17 01b404a4 013e3250 0 01b3e530 7984/8192 CTCP Timer process
Mwe 00efe8b3 0308c15c 013e3250 0 0308a208 7952/8192 L2TP data daemon
Mwe 00efef23 0308e194 013e3250 0 0308c230 7968/8192 L2TP mgmt daemon
Mwe 00eea02b 030c62ac 013a5c10 43 030c2338 16244/16384 ppp_timer_thread
Msi 00f62d57 030c82f4 013e3250 264 030c6360 7924/8192 vpnlb_timer_thread
Mwe 001b96e6 01b7cbbc 01b1e9c8 1 01b7ac48 7728/8192 IPsec message handler
Msi 001c9bac 01b8d4dc 013e3250 2917 01b8b548 7648/8192 CTM message handler
Mwe 00af93b8 031465b4 013e3250 0 03144640 7984/8192 ICMP event handler
Mwe 00831003 0314a724 013e3250 387 031467b0 16100/16384 IP Background
Mwe 0021b267 031a83c4 013123c0 31 03188450 123488/131072 tmatch compile thread
Mwe 009f2405 03290044 013e3250 0 0328c0c0 16072/16384 Crypto PKI RECV
Mwe 009f305a 03294144 013e3250 0 032901e0 16040/16384 Crypto CA
Mwe 0064d4fd 01b3e24c 013e3250 8 01b3c2f8 7508/8192 ESW_MRVL switch interrupt service
<--- More --->
Msi 00646f5c 032c134c 013e3250 3059378 032bf448 7184/8192 esw_stats
Lsi 008cbb80 032dc704 013e3250 3 032da730 7908/8192 uauth_urlb clean
Lwe 008afee7 034a0914 013e3250 197 0349e9b0 6636/8192 pm_timer_thread
Mwe 0052f0bf 034a35ac 013e3250 0 034a1648 7968/8192 IKE Timekeeper
Mwe 00520f6b 034a8adc 0132e2b0 0 034a4e38 15448/16384 IKE Daemon
Mwe 00bf5c78 034ac7ac 01360680 0 034aa7f8 8100/8192 RADIUS Proxy Event Daemon
Mwe 00bc32de 034ae79c 034dcbe0 0 034ac918 7208/8192 RADIUS Proxy Listener
Mwe 00bf5e0f 034b099c 013e3250 0 034aea38 7968/8192 RADIUS Proxy Time Keeper
Mwe 005aac4c 034b3154 013fb980 0 034b1250 7492/8192 Integrity FW Task
M* 008550a5 0009fefc 013e33b0 3183 034e3b20 24896/32768 ci/console
Msi 008eb694 034ed9d4 013e3250 2370 034ebc40 6176/8192 update_cpu_usage
Msi 008e6415 034f7dac 013e3250 1096 034f5eb8 6124/8192 NIC status poll
Mwe 005b63e6 03517d1c 013fbd10 1963 03515d78 7636/8192 IP Thread
Mwe 005becbe 03519e4c 013fbcb0 3 03517e98 7384/8192 ARP Thread
Mwe 004c2b36 0351befc 013fbae0 0 03519fe8 7864/8192 icmp_thread
Mwe 00c7722e 0351e06c 013e3250 0 0351c108 7848/8192 udp_thread
Mwe 00c5d126 0352008c 013fbd00 0 0351e228 7688/8192 tcp_thread
Mwe 00bc32de 03a6982c 03a5ee18 0 03a679b8 7512/8192 EAPoUDP-sock
Mwe 00266c15 03a6b614 013e3250 0 03a699e0 7032/8192 EAPoUDP
Mwe 005a6728 01b27b94 013e3250 0 01b25c30 7968/8192 Integrity Fw Timer Thread
- - - - 47686621 - - scheduler
- - - - 51253819 - - total elapsed
------------------ show failover ------------------
<--- More --->
ERROR: Command requires failover license
------------------ show traffic ------------------
inside:
received (in 51429.740 secs):
7749585 packets905087345 bytes
67 pkts/sec17013 bytes/sec
transmitted (in 51429.740 secs):
10653162 packets10355908020 bytes
40 pkts/sec201026 bytes/sec
1 minute input rate 412 pkts/sec, 51803 bytes/sec
1 minute output rate 475 pkts/sec, 522952 bytes/sec
1 minute drop rate, 24 pkts/sec
5 minute input rate 399 pkts/sec, 59676 bytes/sec
5 minute output rate 483 pkts/sec, 503200 bytes/sec
5 minute drop rate, 9 pkts/sec
outside:
received (in 51430.240 secs):
10758403 packets10441440193 bytes
42 pkts/sec203021 bytes/sec
transmitted (in 51430.240 secs):
7548339 packets872053854 bytes
<--- More --->
63 pkts/sec16037 bytes/sec
1 minute input rate 479 pkts/sec, 523680 bytes/sec
1 minute output rate 387 pkts/sec, 46796 bytes/sec
1 minute drop rate, 3 pkts/sec
5 minute input rate 485 pkts/sec, 503789 bytes/sec
5 minute output rate 387 pkts/sec, 57681 bytes/sec
5 minute drop rate, 2 pkts/sec
_internal_loopback:
received (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Aggregated Traffic on Physical Interface
<--- More --->
Ethernet0/0:
received (in 51431.740 secs):
10758462 packets10640075825 bytes
42 pkts/sec206042 bytes/sec
transmitted (in 51431.740 secs):
7548383 packets1029818127 bytes
63 pkts/sec20023 bytes/sec
1 minute input rate 485 pkts/sec, 537048 bytes/sec
1 minute output rate 395 pkts/sec, 54546 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 485 pkts/sec, 511723 bytes/sec
5 minute output rate 387 pkts/sec, 65495 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/1:
received (in 51433.570 secs):
7749780 packets1066328930 bytes
67 pkts/sec20064 bytes/sec
transmitted (in 51433.570 secs):
10653359 packets10552787020 bytes
40 pkts/sec205006 bytes/sec
1 minute input rate 419 pkts/sec, 59621 bytes/sec
1 minute output rate 480 pkts/sec, 533950 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 399 pkts/sec, 67618 bytes/sec
<--- More --->
5 minute output rate 482 pkts/sec, 511073 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/2:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/3:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
<--- More --->
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/4:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/5:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
<--- More --->
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/6:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Ethernet0/7:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
<--- More --->
0 packets0 bytes
0 pkts/sec0 bytes/sec
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/0:
received (in 51435.510 secs):
18513901 packets11784250044 bytes
25 pkts/sec229023 bytes/sec
transmitted (in 51435.510 secs):
18207269 packets11641332179 bytes
19 pkts/sec226078 bytes/sec
1 minute input rate 891 pkts/sec, 595715 bytes/sec
1 minute output rate 863 pkts/sec, 588935 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 885 pkts/sec, 584035 bytes/sec
5 minute output rate 870 pkts/sec, 580393 bytes/sec
5 minute drop rate, 0 pkts/sec
Internal-Data0/1:
received (in 51436.010 secs):
18207323 packets11641364184 bytes
<--- More --->
19 pkts/sec226076 bytes/sec
transmitted (in 51436.010 secs):
18513954 packets11784281987 bytes
25 pkts/sec229022 bytes/sec
1 minute input rate 855 pkts/sec, 575808 bytes/sec
1 minute output rate 884 pkts/sec, 582339 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 869 pkts/sec, 578350 bytes/sec
5 minute output rate 883 pkts/sec, 581924 bytes/sec
5 minute drop rate, 0 pkts/sec
------------------ show perfmon ------------------
PERFMON STATS: Current Average
Xlates 0/s 0/s
Connections 17/s 6/s
TCP Conns 8/s 2/s
UDP Conns 7/s 2/s
URL Access 0/s 0/s
URL Server Req 0/s 0/s
TCP Fixup 0/s 0/s
TCP Intercept 0/s 0/s
HTTP Fixup 0/s 0/s
<--- More --->
FTP Fixup 0/s 0/s
AAA Authen 0/s 0/s
AAA Author 0/s 0/s
AAA Account 0/s 0/s
------------------ show counters ------------------
Protocol Counter Value Context
IP IN_PKTS 168960 Summary
IP OUT_PKTS 169304 Summary
IP TO_ARP 61 Summary
------------------ show history ------------------
------------------ show firewall ------------------
Firewall mode: Transparent
------------------ show running-config ------------------
<--- More --->
: Saved
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
enable password
names
interface Vlan1
nameif inside
security-level 100
interface Vlan2
nameif outside
security-level 0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
<--- More --->
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd
regex domain1 ".facebook\.com"
regex domain2 ".fb\.com"
regex domain3 ".youtube\.com"
ftp mode passive
access-list ACL_IN extended permit ip any any
pager lines 24
mtu inside 1500
mtu outside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
<--- More --->
arp timeout 14400
access-group ACL_IN in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domain1
match regex domain2
match regex domain3
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
<--- More --->
message-length maximum 512
match domain-name regex class DomainBlockList
drop-connection log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:bb5115ea1d14ee42e7961ef0c9aaed86
: end
<--- More --->
------------------ show startup-config errors ------------------
INFO: No configuration errors
------------------ console logs ------------------
Message #1 : Message #2 : Message #3 : Message #4 : Message #5 : Message #6 : Message #7 : Message #8 : Message #9 : Message #10 : Message #11 : Message #12 : Message #13 : Message #14 :
Total SSMs found: 0
Message #15 :
Total NICs found: 10
Message #16 : 88E6095 rev 2 Gigabit Ethernet @ index 09Message #17 : MAC: 0000.0003.0002
Message #18 : 88E6095 rev 2 Ethernet @ index 08Message #19 : MAC: 001f.9ee8.ffa1
Message #20 : 88E6095 rev 2 Ethernet @ index 07Message #21 : MAC: 001f.9ee8.ffa0
Message #22 : 88E6095 rev 2 Ethernet @ index 06Message #23 : MAC: 001f.9ee8.ff9f
Message #24 : 88E6095 rev 2 Ethernet @ index 05Message #25 : MAC: 001f.9ee8.ff9e
Message #26 : 88E6095 rev 2 Ethernet @ index 04Message #27 : MAC: 001f.9ee8.ff9d
Message #28 : 88E6095 rev 2 Ethernet @ index 03Message #29 : MAC: 001f.9ee8.ff9c
Message #30 : 88E6095 rev 2 Ethernet @ index 02Message #31 : MAC: 001f.9ee8.ff9b
Message #32 : 88E6095 rev 2 Ethernet @ index 01Message #33 : MAC: 001f.9ee8.ff9a
Message #34 : y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 001f.9ee8.ffa2
Message #35 :
Licensed features for this platform:
Message #36 : Maximum Physical Interfaces : 8
<--- More --->
Message #37 : VLANs : 3, DMZ Restricted
Message #38 : Inside Hosts : Unlimited
Message #39 : Failover : Disabled
Message #40 : VPN-DES : Enabled
Message #41 : VPN-3DES-AES : Enabled
Message #42 : VPN Peers : 10
Message #43 : WebVPN Peers : 2
Message #44 : Dual ISPs : Disabled
Message #45 : VLAN Trunk Ports : 0
Message #46 :
This platform has a Base license.
Message #47 :
Message #48 : Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Message #49 : Boot microcode : CNlite-MC-Boot-Cisco-1.2
Message #50 : SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
Message #51 : IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
Message #52 : --------------------------------------------------------------------------
Message #53 : . .
Message #54 : | |
Message #55 : ||| |||
Message #56 : .|| ||. .|| ||.
Message #57 : .:||| | |||:..:||| | |||:.
Message #58 : C i s c o S y s t e m s
Message #59 : --------------------------------------------------------------------------
<--- More --->
Message #60 :
Cisco Adaptive Security Appliance Software Version 7.2(3)
Message #61 :
Message #62 : ****************************** Warning *******************************
Message #63 : This product contains cryptographic features and is
Message #64 : subject to United States and local country laws
Message #65 : governing, import, export, transfer, and use.
Message #66 : Delivery of Cisco cryptographic products does not
Message #67 : imply third-party authority to import, export,
Message #68 : distribute, or use encryption. Importers, exporters,
Message #69 : distributors and users are responsible for compliance
Message #70 : with U.S. and local country laws. By using this
Message #71 : product you agree to comply with applicable laws and
Message #72 : regulations. If you are unable to comply with U.S.
Message #73 : and local laws, return the enclosed items immediately.
Message #74 :
Message #75 : A summary of U.S. laws governing Cisco cryptographic
Message #76 : products may be found at:
Message #77 : http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
Message #78 :
Message #79 : If you require further assistance please contact us by
Message #80 : sending email to [email protected].
Message #81 : ******************************* Warning *******************************
Message #82 :
<--- More --->
Message #83 : Copyright (c) 1996-2007 by Cisco Systems, Inc.
Message #84 : Restricted Rights Legend
Message #85 : Use, duplication, or disclosure by the Government is
Message #86 : subject to restrictions as set forth in subparagraph
Message #87 : (c) of the Commercial Computer Software - Restricted
Message #88 : Rights clause at FAR sec. 52.227-19 and subparagraph
Message #89 : (c) (1) (ii) of the Rights in Technical Data and Computer
Message #90 : Software clause at DFARS sec. 252.227-7013.
Message #91 : Cisco Systems, Inc.
Message #92 : 170 West Tasman Drive
Message #93 : San Jose, California 95134-1706
ciscoasa# -
Setting up site to site vpn with cisco asa 5505
I have a cisco asa 5505 that needs to be set up for site to site vpn to a cisco asa 5500. The 5505 is the remote office and the 5500 is the main office.
IP of remote office router is 71.37.178.142
IP of the main office firewall is 209.117.141.82
Can someone tell me if my config is correct, this is the first time I am setting this up and it can not be tested until I set it up at the remote office. I would rather know its correct before I go.
ciscoasa# show run
: Saved
ASA Version 7.2(4)
hostname ciscoasa
domain-name default.domain.invalid
enable password TMACBloMlcBsq1kp encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 host 209.117.141.82
access-list inside_nat0_outbound extended permit ip host 71.37.178.142 host 209.117.141.82
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-524.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 209.117.141.82
crypto map outside_map 1 set transform-set ESP-AES-256-SHA
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption aes-256
hash sha
group 5
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
vpdn username [email protected] password ********* store-local
dhcpd auto_config outside
dhcpd address 192.168.1.2-192.168.1.129 inside
dhcpd enable inside
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:7e338fb2bf32a9ceb89560b314a5ef6c
: end
ciscoasa#
Thanks!Hi Mandy,
By using following access list define Peer IP as source and destination
access-list outside_1_cryptomap extended permit ip host 71.37.178.142 host 209.117.141.82
you are not defining the interesting traffic / subnets from both ends.
Make some number ACL 101 as you do not have to write the extended keyword then if you like as follows, or else NAME aCL will also work:
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
access-list 101 remark CCP_ACL Category=4 access-list 101 remark IPSEC Rule
!.1..source subnet(called local encryption domain) at your end 192.168.200.0
!..2.and destination subnet(called remote encryption domain)at other end 192.168.100.0 !.3..I mean you have to define what subnets you need to communicate between which are behind these firewalls
!..4...Local Subnets behind IP of the main office firewall is 209.117.141.82 say
!...at your end 192.168.200.0
!..5.Remote Subnets behind IP of remote office router is 71.37.178.142 say
!...at other end 192.168.100.0
Please use Baisc Steps as follows:
A. Configuration in your MAIN office having IP = 209.117.141.82 (follow step 1 to 6)
Step 1.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.200.0 0.0.0.255 192.168.100.0 0.0.0.255
Step 2.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 3.
Define Preshared key or PKI which you will use with other side Peer address 71.37.178.142, either key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 2 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 71.37.178.142
or , but not both
crypto isakmp key 6 CISCO123 address71.37.178.142
step 4.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 5.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 6.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Configure the same but just change ACL on other end in step one by reversing source and destination
and also set the peer IP of this router in other end.
So other side config should look as follows:
B. Configuration in oyur Remote PEER IP having IP = 71.37.178.142 (follow step 7 to 12)
Step 7.
Define Crypto ACL/ mirror ACL for other end (change source to destination and destination to source in other side router or VPN device and thats why they are called mirror ACL/ or also called Proxy ID or also called Proxy ACL, your interesting traffic , that you want to encrypt / trave/enter in the tunnel)
access-list outside_1_cryptomap extended ip 192.168.100.0 0.0.0.255 192.168.200.0 0.0.0.255
Step 8.
Config ISAKMP Policy with minimum 4 parameters are to be config for
crypto isakmp policy 10
authentication pre-share ---> Ist parameter of setting Authentication type ISAKMP Policy is OK
encryption aes-256 --->2nd parameter of ISAKMP Policy is OK
hash sha ---> 3rd parameter of ISAKMP Policy is OK
group 5 ---> 4th parameter of ISAKMP Policy is OK
lifetime 86400 ------ > this 5th parameter is optional , and will negotiate for the less value at either end or by default is will be taken 86400
Step 9.
Define Preshared key or PKI which you will use with other side Peer address key type 0 is Plain text anyone can see it over internet, or use key type 6 for encrypted key , say your password is CISCO123
Here in your case in step 8 Authentication is using PSK, looks you have not defines Password
Use following command:
crypto isakmp key 0 CISCO123 address 209.117.141.82
or , but not both
crypto isakmp key 6 CISCO123 address 209.117.141.82
step 10.
Define Transform set , which will be used for phase 2 tunnel parameters, if you use ESP it can have to sets one cor encryption and other for Authentication.
Here is yours one:
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
this is correct but give name somthing easier to remember /distinguish it is a transform set , like TSET1 instead of ESP-AES-256-SHA ,try following (here you are using ESP so for encryption we use first set as esp-des and for authentication we use second set esp-sha-hmac)
crypto ipsec transform-set TSET1 esp-des esp-sha-hmac
or
crypto ipsec transform-set TSET1 esp-aes-256 esp-sha-hmac
Suppose you are using only AH then as AH does not support encryption or confidentiality hence it always use onle one set not 2 sets like ESP(remember the difference) say for example only one set for auth etc but no set for encryption hence AH have no such sets like ah-des or ah-3des or ah-aes, it has only second set for authentication like
ah-sha-hmac or ah-md5-hmac
crypto ipsec transform-set TSET1 ah-sha-hmac
or
crypto ipsec transform-set TSET1 ah-md5-hmac
Step 11.
Now configure Crypto MAP as follows and only one CMPA can be applied to OUTSIDE Interface as VPN tunnel is alsways applied for traffic from inside subnets to outside subnets and only once Cryptomap can be applied to OUTSIDE Interface and hence for several VPN peers from different vendors we use seq no 10, 2 30 for different tunnels in one single CMAP:
crypto map ipsec-isakmp
1. Define peer -- called WHO to set tunnel with
2. Define or call WHICH - Transform Set, only one is permissible
3. Define WHAT to call interesting traffic define in your ACL or Proxy ID or Proxy ACL in step 1 using match address
Like in your case it is but ipsec-isakmp keyword missing in the ;ast
crypto map outside_map 10 ipsec-isakmp
1. set peer 209.117.141.82 -----> is correct as this is your other side peer called WHO in my step
2. set transform-set TSET1 -----> is correct as this is WHICH, and only one transform set can be called
!..In you case it is correct
!...set transform-set ESP-AES-256-SHA (also correct)
3. match address outside_1_cryptomap ---->Name of the extended ACL define as WHAT to pass through this tunnel
4. set pfs group5 (this is optional but if config at one end same has to be config at other side peer as well)
Step 12.
Now apply this one crypto MAP to your OUTSIDE interface always
interface outside
crypto map outside_map
Now initite a ping
Here is for your summary:
IPSec: Site to Site - Routers
Configuration Steps
Phase 1
Step 1: Configure Mirrored ACL/Crypto ACL for Interesting Traffic
Step 2: Configure ISAKMP Policy
Step 3: Configure ISAKMP Key
Phase 2
Step 4: Configure Transform Set
Step 5: Configure Crypto Map
Step 6: Apply Crypto Map to an Interface
To debug for Phase 1 and Phase 2. Store it in buffer without displaying logs on terminal.
Router#debug crpyto isakmp
Router#debug crpyto ipsec
Router(config)# logging buffer 7
Router(config)# logging buffer 99999
Router(config)# logging console 6
Router# clear logging
Configuration
In R1:
(config)# access-list 101 permit ipo host 10.1.1.1 host 10.1.2.1
(config)# crypto isakmp policy 10
(config-policy)# encryption 3des
(config-policy)# authentication pre-share
(config-policy)# group 2
(config-policy)# hash sha1
(config)# crypto isakmp key 0 cisco address 2.2.2.1
(config)# crypto ipsec transform-set TSET esp-3des sha-aes-hmac
(config)# crypto map CMAP 10 ipsec-isakmp
(config-crypto-map)# set peer 2.2.2.1
(config-crypto-map)# match address 101
(config-crypto-map)# set transform-set TSET
(config)# int f0/0
(config-if)# crypto map CMAP
Similarly in R2
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Change to Transport Mode, add the following command in Step 4:
(config-tranform-set)# mode transport
Even after doing this change, the ipsec negotiation will still be done through tunnel mode if pinged from Loopback to Loopback. To overcome this we make changes to ACL.
Change to Aggressive Mode, replace the Step 3 command with these commands in R1:
(config)# crypto isakmp peer address 2.2.2.1
(config-peer)# set aggressive-mode password cisco
(config-peer)# set aggressive-mode clien-endpoint ipv4-address 2.2.2.1
Similarly on R2.
The below process is for the negotiation using RSA-SIG (PKI) as authentication type
Debug Process:
After we debug, we can see the negotiation between the two peers. The first packet of the interesting traffic triggers the ISAKMP (Phase1) negotiation. Important messages are marked in BOLD and explanation in RED
R2(config)#do ping 10.1.1.1 so lo0 // Interesting Traffic
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
Packet sent with a source address of 2.2.2.2
Mar 2 16:18:42.939: ISAKMP:(0): SA request profile is (NULL) // Router tried to find any IPSec SA matching the outgoing connection but no valid SA has been found in Security Association Database (SADB)
Mar 2 16:18:42.939: ISAKMP: Created a peer struct for 20.1.1.10, peer port 500
Mar 2 16:18:42.939: ISAKMP: New peer created peer = 0x46519678 peer_handle = 0x8000000D
Mar 2 16:18:42.939: ISAKMP: Locking peer struct 0x46519678, refcount 1 for isakmp_initiator
Mar 2 16:18:42.939: ISAKMP: local port 500, remote port 500
Mar 2 16:18:42.939: ISAKMP: set new node 0 to QM_IDLE
Mar 2 16:18:42.939: ISAKMP:(0):insert sa successfully sa = 4542B818
Mar 2 16:18:42.939: ISAKMP:(0):Can not start Aggressive mode, trying Main mode. // Not an error. By default it is configured for Main Mode
Mar 2 16:18:42.939: ISAKMP:(0):No pre-shared key with 20.1.1.10! // Since we are using RSA Signature, this message. If we use pre-share, this is where it would indicate so!
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-rfc3947 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-07 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-03 ID
Mar 2 16:18:42.939: ISAKMP:(0): constructed NAT-T vendor-02 ID
Mar 2 16:18:42.939: ISAKMP:(0):Input = IKE_MESG_FROM_IPSEC, IKE_SA_REQ_MM
Mar 2 16:18:42.939: ISAKMP:(0):Old State = IKE_READY New State = IKE_I_MM1
Mar 2 16:18:42.943: ISAKMP:(0): beginning Main Mode exchange
Mar 2 16:18:42.943: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.943: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.943: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_NO_STATE // Sending ISAKMP Policy to peer
Mar 2 16:18:42.947: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.947: ISAKMP:(0):Old State = IKE_I_MM1 New State = IKE_I_MM2
Mar 2 16:18:42.947: ISAKMP:(0): processing SA payload. message ID = 0
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch // Do not worry about this! Not an ERROR!
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947:.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max = 1/2/4 ms
R2(config)# ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.947: ISAKMP : Scanning profiles for xauth ...
Mar 2 16:18:42.947: ISAKMP:(0):Checking ISAKMP transform 1 against priority 10 policy
Mar 2 16:18:42.947: ISAKMP: encryption 3DES-CBC
Mar 2 16:18:42.947: ISAKMP: hash SHA
Mar 2 16:18:42.947: ISAKMP: default group 2
Mar 2 16:18:42.947: ISAKMP: auth RSA sig
Mar 2 16:18:42.947: ISAKMP: life type in seconds
Mar 2 16:18:42.947: ISAKMP: life duration (VPI) of 0x0 0x1 0x51 0x80
Mar 2 16:18:42.947: ISAKMP:(0):atts are acceptable. Next payload is 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:actual life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Acceptable atts:life: 0
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa vpi_length:4
Mar 2 16:18:42.947: ISAKMP:(0):Fill atts in sa life_in_seconds:86400
Mar 2 16:18:42.947: ISAKMP:(0):Returning Actual lifetime: 86400
Mar 2 16:18:42.947: ISAKMP:(0)::Started lifetime timer: 86400.
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID seems Unity/DPD but major 123 mismatch
Mar 2 16:18:42.947: ISAKMP:(0): vendor ID is NAT-T v2
Mar 2 16:18:42.947: ISAKMP:(0): processing vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0): processing IKE frag vendor id payload
Mar 2 16:18:42.951: ISAKMP:(0):Support for IKE Fragmentation not enabled
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM2
Mar 2 16:18:42.951: ISAKMP (0): constructing CERT_REQ for issuer cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:42.951: ISAKMP:(0): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_SA_SETUP // Sending Key Exchange Information to peer
Mar 2 16:18:42.951: ISAKMP:(0):Sending an IKE IPv4 Packet.
Mar 2 16:18:42.951: ISAKMP:(0):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:42.951: ISAKMP:(0):Old State = IKE_I_MM2 New State = IKE_I_MM3
Mar 2 16:18:42.955: ISAKMP (0): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_SA_SETUP // Receive key exchange information from peer
Mar 2 16:18:42.955: ISAKMP:(0):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:42.955: ISAKMP:(0):Old State = IKE_I_MM3 New State = IKE_I_MM4
Mar 2 16:18:42.959: ISAKMP:(0): processing KE payload. message ID = 0
Mar 2 16:18:43.003: ISAKMP:(0): processing NONCE payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): processing CERT_REQ payload. message ID = 0
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants a CT_X509_SIGNATURE cert
Mar 2 16:18:43.007: ISAKMP:(1008): peer wants cert issued by cn=ca_server OU=cisco C=India S=Karnataka L=Bangalore
Mar 2 16:18:43.007: Choosing trustpoint CA_Server as issuer
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is Unity
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID seems Unity/DPD but major 180 mismatch
Mar 2 16:18:43.007: ISAKMP:(1008): vendor ID is XAUTH
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008): speaking to another IOS box!
Mar 2 16:18:43.007: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.007: ISAKMP:(1008):vendor ID seems Unity/DPD but hash mismatch
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): His hash no match - this node outside NAT
Mar 2 16:18:43.007: ISAKMP:received payload type 20
Mar 2 16:18:43.007: ISAKMP (1008): No NAT Found for self or peer
Mar 2 16:18:43.007: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.007: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM4
Mar 2 16:18:43.011: ISAKMP:(1008):Send initial contact
Mar 2 16:18:43.011: ISAKMP:(1008):My ID configured as IPv4 Addr, but Addr not in Cert!
Mar 2 16:18:43.011: ISAKMP:(1008):Using FQDN as My ID
Mar 2 16:18:43.011: ISAKMP:(1008):SA is doing RSA signature authentication using id type ID_FQDN
Mar 2 16:18:43.011: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : R2
protocol : 17
port : 500
length : 10
Mar 2 16:18:43.011: ISAKMP:(1008):Total payload length: 10
Mar 2 16:18:43.019: ISAKMP (1008): constructing CERT payload for hostname=R2+serialNumber=FHK1502F2H8
Mar 2 16:18:43.019: ISAKMP:(1008): using the CA_Server trustpoint's keypair to sign
Mar 2 16:18:43.035: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) MM_KEY_EXCH
Mar 2 16:18:43.035: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.035: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.035: ISAKMP:(1008):Old State = IKE_I_MM4 New State = IKE_I_MM5
Mar 2 16:18:43.047: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) MM_KEY_EXCH
// "MM_KEY_EXCH" indicates that the peers have exchanged DH Public keys and generated a shared secret!
Mar 2 16:18:43.047: ISAKMP:(1008): processing ID payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP (1008): ID payload
next-payload : 6
type : 2
FQDN name : ASA1
protocol : 0
port : 0
length : 12
Mar 2 16:18:43.047: ISAKMP:(0):: peer matches *none* of the profiles // Normal Message! Not an error!
Mar 2 16:18:43.047: ISAKMP:(1008): processing CERT payload. message ID = 0
Mar 2 16:18:43.047: ISAKMP:(1008): processing a CT_X509_SIGNATURE cert
Mar 2 16:18:43.051: ISAKMP:(1008): peer's pubkey isn't cached
Mar 2 16:18:43.059: ISAKMP:(1008): Unable to get DN from certificate!
Mar 2 16:18:43.059: ISAKMP:(1008): Cert presented by peer contains no OU field.
Mar 2 16:18:43.059: ISAKMP:(0):: peer matches *none* of the profiles
Mar 2 16:18:43.063: ISAKMP:(1008): processing SIG payload. message ID = 0
Mar 2 16:18:43.067: ISAKMP:received payload type 17
Mar 2 16:18:43.067: ISAKMP:(1008): processing vendor id payload
Mar 2 16:18:43.067: ISAKMP:(1008): vendor ID is DPD
Mar 2 16:18:43.067: ISAKMP:(1008):SA authentication status:
authenticated
Mar 2 16:18:43.067: ISAKMP:(1008):SA has been authenticated with 20.1.1.10
Mar 2 16:18:43.067: ISAKMP: Trying to insert a peer 40.1.1.1/20.1.1.10/500/, and inserted successfully 46519678. // SA inserted into SADB
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_FROM_PEER, IKE_MM_EXCH
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM5 New State = IKE_I_MM6
Mar 2 16:18:43.067: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_MAIN_MODE
Mar 2 16:18:43.067: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_I_MM6
Mar 2 16:18:43.071: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PROCESS_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):Old State = IKE_I_MM6 New State = IKE_P1_COMPLETE
Mar 2 16:18:43.071: ISAKMP:(1008):beginning Quick Mode exchange, M-ID of -1523793378
Mar 2 16:18:43.071: ISAKMP:(1008):QM Initiator gets spi
Mar 2 16:18:43.075: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.075: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.075: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_INTERNAL, IKE_INIT_QM
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_QM_READY New State = IKE_QM_I_QM1
Mar 2 16:18:43.075: ISAKMP:(1008):Input = IKE_MESG_INTERNAL, IKE_PHASE1_COMPLETE
Mar 2 16:18:43.075: ISAKMP:(1008):Old State = IKE_P1_COMPLETE New State = IKE_P1_COMPLETE
Mar 2 16:18:43.079: ISAKMP (1008): received packet from 20.1.1.10 dport 500 sport 500 Global (I) QM_IDLE // IPSec Policies
Mar 2 16:18:43.079: ISAKMP:(1008): processing HASH payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing SA payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008):Checking IPSec proposal 1
Mar 2 16:18:43.079: ISAKMP: transform 1, ESP_3DES
Mar 2 16:18:43.079: ISAKMP: attributes in transform:
Mar 2 16:18:43.079: ISAKMP: SA life type in seconds
Mar 2 16:18:43.079: ISAKMP: SA life duration (basic) of 3600
Mar 2 16:18:43.079: ISAKMP: SA life type in kilobytes
Mar 2 16:18:43.079: ISAKMP: SA life duration (VPI) of 0x0 0x46 0x50 0x0
Mar 2 16:18:43.079: ISAKMP: encaps is 1 (Tunnel)
Mar 2 16:18:43.079: ISAKMP: authenticator is HMAC-SHA
Mar 2 16:18:43.079: ISAKMP:(1008):atts are acceptable. // IPSec attributes are acceptable!
Mar 2 16:18:43.079: ISAKMP:(1008): processing NONCE payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.079: ISAKMP:(1008): processing ID payload. message ID = -1523793378
Mar 2 16:18:43.083: ISAKMP:(1008): Creating IPSec SAs
Mar 2 16:18:43.083: inbound SA from 20.1.1.10 to 40.1.1.1 (f/i) 0/ 0
(proxy 1.1.1.1 to 2.2.2.2)
Mar 2 16:18:43.083: has spi 0xA9A66D46 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: outbound SA from 40.1.1.1 to 20.1.1.10 (f/i) 0/0
(proxy 2.2.2.2 to 1.1.1.1)
Mar 2 16:18:43.083: has spi 0x2B367FB4 and conn_id 0
Mar 2 16:18:43.083: lifetime of 3600 seconds
Mar 2 16:18:43.083: lifetime of 4608000 kilobytes
Mar 2 16:18:43.083: ISAKMP:(1008): sending packet to 20.1.1.10 my_port 500 peer_port 500 (I) QM_IDLE
Mar 2 16:18:43.083: ISAKMP:(1008):Sending an IKE IPv4 Packet.
Mar 2 16:18:43.083: ISAKMP:(1008):deleting node -1523793378 error FALSE reason "No Error"
Mar 2 16:18:43.083: ISAKMP:(1008):Node -1523793378, Input = IKE_MESG_FROM_PEER, IKE_QM_EXCH
Mar 2 16:18:43.083: ISAKMP:(1008):Old State = IKE_QM_I_QM1 New State = IKE_QM_PHASE2_COMPLETE // At this point tunnels are up and ready to pass traffic!
Verification Commands
#show crypto isakmp SA
#show crypto ipsec SA
Kindly rate if you find the explanation useful !!
Best Regards
Sachin Garg
Maybe you are looking for
-
How to control number of open sessions on Portal
We recently release our Portal production environment and we have been told that there are some users capable to open up to more than 100 sessions. Is there a way to control this on Portal, let's says, to allow only up to 4 sessions per user? Thanks
-
[SOLVED] plasma-desktop could not start
hi! i have almost two weeks after installing archlinux yesterday i powered off the laptop and when i powered it on but there was no plasma-desktop then i tried plasma-desktop in the consoe and i get this output [issam@fuhrer ~]$ plasma-desktop QDBusC
-
unable to buy pages
-
I have a MAC Tiger and updated to a Snow Leopard,
Having trouble with Apple works 6 Just updated my Tiger to a Snow Leopard and certain pages in the Apple works 6 take to long to print. 4 to 5 minutes sometimes before the printer starts. Not all the forme just a few. Others print very fast. Hard dri
-
Hi, I would like to know if anyone know how to set a specific cell colour in a JTable, or if they know any links to when i can find help...thanks in advance Rudy