Unable to see PXIe-8133 in MAX on host computer

Hi,
I seem to be running into a very basic problem. I'm trying to use the PXIe-8133 system in Real-Time but I am unable to detect the system in MAX. I can't even see an "Unconfigured RT System" with IP Address of 0.0.0.0 as it shows in the documentation. I've installed all of the drivers for the PXIe 8133 on my host computer found here: 
http://joule.ni.com/nidu/cds/view/p/id/2030/lang/en, but this has not solved the problem. 
One thing to note, when I attach a monitor to the PXIe-8133, it says: "System State: No Software Installed" and also "Can't Find Suitable Device for Drive C". But only one of our 2 PXIe-8133's is displaying this and we are not able to see the PXIe-8133 system in MAX even in the system which does not display these warning messages.
Thanks very much in advance for your help!
Steven 

Hey Steven,
So a couple things to make sure of:
1. Reboot your PXI and when it is rebooting up keep hitting the delete key until you see an output on your screen that gives you different options to select.
2. Go over to Real Time menu (think it is like the fourth option from the left on the top).
3. Once in here the first option is what mode of Real-Time do you want to access. Select LabVIEW Real-Time Safe Mode.
4. Go to the last menu option and save changes. This will reboot into the mode we just set.
Once it is rebooted, go into MAX on your computer that is on the same subnet as this PXI and refresh remote systems. You should now see a device with an IP address of 0.0.0.0. Make the changes to the IP address that you want. Once you save those changes it will reboot the PXI. If you are still not able to get the target showing, try to go back into the bios and there is also another option to choose under the Real-Time heading to reset IP by hardware switch, software or none. Change that to software. Save again and then it will reboot and see if you can now see it in MAX and make the corresponding IP changes.
David A.
National Instruments
Applications Engineer

Similar Messages

  • PXIe 8133 Real Time Configuration Issue with MAX

    I seem to be running to a weird problem in configuring a PXIe 8133 into an RT system. After I change it in bios to boot safe mode, MAX detects the system no problem through remote connection. When I try to change its IP (while the PXIe8133 is in Safe Mode), it does not allow me to do so. Specifically, the text on top of Network Settings Tab mentions that it cannot apply the settings. I also have tried reformating the RT, and uploading software. The format performs OK, but still the same problem with IP and communication. The software upload results in communication timeout.
    I am not running any firewalls, etc. The link is direct cable between the host and the target (PXIe8133). I am running LV2010 RT on the host.
    If I am missing a simple step in getting through this obstacle, please let me know. Any suggestions are apreciated. Thanks in advance.
    Peter

    Hello,
    Just wondering are you using DHCP or static IP addressing? If you are using static IP, ensure you have all the fields on the 'Network Settings Tab' populated including the Gateway and DNS server. Both fields can be populated with the address 0.0.0.0. Hope this helps.
    Best,
    National Instruments
    Applications Engineer

  • Max unable to see ni 9870 or 1

    Hi
    I have a Crio ni 9022 4 slot, Crio 9113. 
    Using LV 14.
    As far as is see i have all the software installed. Attached is the software installed.
    Problems is, i cannot see NI9870/1 in MAX to be able to see the com ports to be able to use them 
    in scan mode or FPGA.
    The Ni9871 will be used in FPGA.
    NI 9870 in scan mode.
    Thanks in advanced
    Douglas
    Attachments:
    cRio9022.png ‏201 KB

    Hi
    Thanks.
    Both are using modbus. Ni9871 will be using the ni fpga modbus drivers. deploy onto fpga.
    NI 9870 deploy onto the realtime engine of the Crio. Using the modbus drivers supplied by NI.
     The Crio's are in there own area in the Network and pc's in another, so have to go through firewalls.
    I have 3 pc's, two are dedicated to there own Crio. One pc mine will see all Crio's.
    I have one pc connected to a Crio, W3304, and it can see the NI9870/1 in MAx. But can't figure why the other  pc
    can't see the ni 9870/1 on its Crio W4247. Attached file.
    For Scanmode i need the com port address, which comes from MAX.
    cheers
    Douglas
    Attachments:
    cRio9022-a.png ‏130 KB

  • Why i am unable to see my thread in MY questions list

    Hi Folks,
    HR -Hide additional field for rest of subtypes . open it for 1 subtype ?
    Could u kindly let me know why i am unable to see this (MY) thread in my questonare(Your questions) list??
    Regards
    Sas

    >
    Julius Bussche wrote:
    > Please do the needfull. <= given the frequency, I think this is a perfectly acceptable expression in India, no?
    Ya thats true....:-)
    I have often noticed in the ABAP forums that people with very good intentions, break the rules because they did not know about them, but also because they perhaps could not imagine them given the previous examples.
    Ya innocence is acceptable but not the lazyness .....and Its also not possible to tell each & every new commer about the rules & regulation keep on saying its not possible...
    From our side is also there is some mistake to make them aware of this professional forum .
    First i want to point No special tutorial is available when some is registering with the sdn..No one is intrested to study pages of pages rules and regulations until or unless they experience..There should be a manditory tutorial if possibel video(More effective or other wise Power point presentation for some time..add the contents with examples) which should be taken for awhile like what's this forum intensions and how can u search a answer  .....and what happens if we post irrelevant subjects , Phrases..After doing all this if some one does post the wrong one then definelty there is reason to get him punished
    Of course, I very firmly believe that "the rules" are a minimum baseline rules - but I think often there are easily misunderstood expected behavior in the prefessional forums .
    > What is your opinion to change this expected behavior to a minimum baseline (otherwise deleted)?
    My opinon is delete is Final option Julius ..
    Before this rules..every one is in the gaming of points & prizes..(By copy post , etc)
    Now my opinion is that past GUESTS no use of discussing them....instead of deleting them Completely ..Make a option of ban  them for a month or for 10 days for sdn Mark them red color ....
    Just like referee in Football...Show some yellow card..Last option is Red card..:-)))
    > I think we have made good progress in the forums, and nothing is perfect (thank goodness but it is nice to have usable and knowledgable forums only, and not spam.
    >
    > What do you think SaS?
    > Cheers,
    > Julius
    Ya pretty GOOD...u agree or not The max credit to ur team Especially after u r entrance...
    Regards
    Sas
    Ps:Thankx amit the one i really confuse every time....Gate Way of india & india gate..
    actually both are Familiar for me.i visit them oftenly ..thats  ..ok..Good that u recognize the people belongs to whihc country by smell....

  • Flash 11.7.700.202 - reports of unable to see video

    We run a social video site and have had many reports of users unable to see video in the last few days. Our code has not changed and we believe this is due to the 11.7.700.202 release as these problems were not previously reported.
    Symptoms:
    User is subscribing via rtmfp to a live stream on an Adobe FMS. When this happens, we don't know if they fail to connect or the connect succeeds and they don't see video. We use an inhouse flash app. The feed is available on the FMS since other users are successfully subscribing to the same feed.
    This happens to a small percent of users but that leads to many reports across our user base.
    Refreshing the page, which reinstantiates the flash app, removes the problem.
    Is anyone else seeing problems with viewing video from the newly updated flash player?
    Thank you,
    Robert

    We found the problem and it is on our side, not a problem with the flash upgrade. I'll write what happened here in case it can help anyone else.
    On Sunday night, two days after this post, one of our FMSs stopped accepting RTMFP publishes. When we examined the box we found that it was reporting that it had reached its max licensed RTMFP connections. We know there weren't that number of connections on there and suspect that connections leaked. After restarting the box, the FMS resumed accepting RTMFP publishes. This failure has never happened to us before so we're treating it as a one-off and not investigating. 
    Since the restart of that FMS, reports of subscribe failures have disappeared. That's great and we're presuming the restart fixed the subscribe failures. The strange thing is that users were reporting subscribe failures several days before we observed any publish failures. That said, we know this FMS was in a strange state so we concluded our investigation.
    Thanks to Chris for the quick response on this.
    Robert

  • Unable to see interface on ASA 5510 Firewall

    Hi All,
    I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
    Below is the output.
    ciscoasa# sh int ip br
    Interface                  IP-Address      OK? Method Status                Protocol
    Ethernet0/0                x.x.x.x           YES CONFIG up                    up
    Ethernet0/1                x.x.x.x           YES CONFIG up                    up
    Ethernet0/2                unassigned      YES unset  administratively down down
    Internal-Control0/0        127.0.1.1       YES unset  up                    up
    Internal-Data0/0           unassigned      YES unset  up                    up
    Management0/0              192.168.1.1     YES CONFIG up                    up
    Please suggest what could be the reason.
    Regards
    Pankaj

    Hi Ramraj,
    Even i have the base license for my ASA 5510 which is showing all the 4 interfaces in sh ver. I don't think so license would be an issue. There should be some IOS code bug that needs to be upgraded. If this goes for an OS upgrade it should get resolved.
    Its not showing up in sh ver . As Karsten said he might be running on old IOS version.
    fy-a# sh ver
    Cisco Adaptive Security Appliance Software Version 8.4(4)1
    Device Manager Version 6.4(5)
    Compiled on Thu 14-Jun-12 11:20 by builders
    System image file is "disk0:/asa844-1-k8.bin"
    Config file at boot was "startup-config"
    fy-a up 1 day 1 hour
    Hardware:   ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
    Internal ATA Compact Flash, 256MB
    BIOS Flash M50FW016 @ 0xfff00000, 2048KB
    Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
                                 Boot microcode   : CN1000-MC-BOOT-2.00
                                 SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
                                 IPSec microcode  : CNlite-MC-IPSECm-MAIN-2.06
                                 Number of accelerators: 1
    0: Ext: Ethernet0/0         : address is 2c54.2d0c.8f1a, irq 9
    1: Ext: Ethernet0/1         : address is 2c54.2d0c.8f1b, irq 9
    2: Ext: Ethernet0/2         : address is 2c54.2d0c.8f1c, irq 9
    3: Ext: Ethernet0/3         : address is 2c54.2d0c.8f1d, irq 9
    4: Ext: Management0/0       : address is 2c54.2d0c.8f1e, irq 11
    5: Int: Not used            : irq 11
    6: Int: Not used            : irq 5
    Licensed features for this platform:
    Maximum Physical Interfaces       : Unlimited      perpetual
    Maximum VLANs                     : 50             perpetual
    Inside Hosts                      : Unlimited      perpetual
    Failover                          : Disabled       perpetual
    VPN-DES                           : Enabled        perpetual
    VPN-3DES-AES                      : Enabled        perpetual
    Security Contexts                 : 0              perpetual
    GTP/GPRS                          : Disabled       perpetual
    AnyConnect Premium Peers          : 2              perpetual
    AnyConnect Essentials             : Disabled       perpetual
    Other VPN Peers                   : 250            perpetual
    Total VPN Peers                   : 250            perpetual
    Shared License                    : Disabled       perpetual
    AnyConnect for Mobile             : Disabled       perpetual
    AnyConnect for Cisco VPN Phone    : Disabled       perpetual
    Advanced Endpoint Assessment      : Disabled       perpetual
    UC Phone Proxy Sessions           : 2              perpetual
    Total UC Proxy Sessions           : 2              perpetual
    Botnet Traffic Filter             : Disabled       perpetual
    Intercompany Media Engine         : Disabled       perpetual
    This platform has a Base license.
    Serial Number: JMX1AXXXXX
    Running Permanent Activation Key: XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
    Configuration register is 0x1
    Configuration has not been modified since last system restart.
    fy-a#
    Ramraj please do correct me if am wrong.
    Please do rate if the given information helps.
    By
    Karthik

  • When using the camera downloader in Adobe Bridge CS6 with Nikon D5200 we are unable to see previews of the photos and it is very slow to download. The issue occurs under a the users rights, but not under admin level. This is a new issue

    When using the camera downloader in Adobe Bridge CS6 with Nikon D5200 we are unable to see previews of the photos and it is very slow to download. The issue occurs under a the users rights, but not under admin level. This is a new issue.

    Hi Jdentremont,
    Lync client gets user photos by first querying the Address Book Web Query (ABWQ) service on the server, which is exposed through the Distribution List Expansion web service. The client receives
    the image file and then copies it to the user's cache to avoid downloading the image each time it needs to be displayed. The attribute values returned from the query are also stored in the cached Address Book Service entry for the user. The Address Book Service
    deletes all cached images every 24 hours, which means that it can take up to 24 hours for new user images to be updated in the cache on the server.
    To troubleshoot your problem, please follow the steps below:
    1.  Navigate to
     “X:\share\1-WebServices-1\ABfiles\000000000\000000000” folder. (ABS file share)
    You should see some photo files in this folder as the following screenshot.
    2. Delete all the files in this folder.
    3. On test PC, delete local cache files.
    %userprofile%\AppData\Local\Microsoft\Office\15.0\Lync\[email protected]
    4. Sign-in Lync with the test account.
    5. Go back to the ABS file share, check if there is any Photo file in the folder.
    Best regards,
    Eric
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

  • Unable to see pipe line steps in the SXMB_MONI

    HI,
    i have done the development and quality work for my p i7.1
    i was testing the messages in the Quality System.
    So i went to SXMB_MONI to see the messages.
    After double clicking on the  successfully processed message, it shows
    pipe line steps.
    in that I am able to see
    1.inbound message(CENTRAL)
    2.XML Validation inbound channel Request
    3. call adapter
    4. Response
    but i am unable to see
    1. Receiver Determination
    2. Interface Determination
    3. Receiver Grouping
    4. Request Message Mapping
    5. Technical Routing
    whereas  in the develoment system i am able to see the above all.
    is there any configuration i have to do in the SXMB_ADM?

    can i know that   Configuration objects were created/ imported by using transport mechanisum?
    if created ,
    check the cache status and re activated those objects whatever u r posted in thread.
    if transported :
    u ll follow ,whatever posted by Earlier

  • Unable to see 'Search Dialog Box  Component' option

    In trying to follow Thilo Brandt's article to 'Develop a Serach Component for KM Search iView', but I'm unable to see Content Management -> User Interface -> Mapping -> Search Dialog Box Component. Is there something I need to 'turn on' so that I can view that option?
    We are using EP6 SP2.
    thanks,
    Biju.

    Forgot to mention that the article is available at: https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sapportals.km.docs/documents/a1-8-4/developing a search component for km search iview.article

  • HT204291 Airplay mirroring. Macbook 2012 retina display. Unable to see desktop on television, audio works perfectly. Both OS on ATV and Mac are running latest versions

    Airplay mirroring.
    Macbook 2012 retina display. Unable to see desktop on television, audio works perfectly. Both OS on ATV and Mac are running latest versions.
    Firewall set correctly (allow incoming...)
    When I click mirroring to turn it on, teh Apple TV screen goes blank (from its home setting)
    Any help appreciated.

    Hi!
    I figured it out! It was a firewall issue.
    I use Handsoff and I checked it before i wrote here. There was no "user defined rule" that denied the communication but when i changed to "All rules" the program displayed several rules regarding AppleTV and its IP.
    So if anybody has the same problem make sure you see all rules of your firewall and get rid of the AppleTV related rules generated by the program itself. You dont need to update to the latest iOS on the AppleTV!
    I hope that I can help some people with this info to fix the problem.

  • Wired computers unable to see printer on Airport Express...help?

    Hi all,
    I recently set up an Airport Extreme on our office network to offer wireless network access piggybacked on our wired router. I then purchased an Airport Express which I was planning on using as a wireless print server for our Canon i9900 for all office computers connecting wired or wirelessly, which would interface with the network via the Airport Extreme Base Station.
    I have configured the Express as an extension of the existing Airport network, and attached the printer to it via USB. All the computers in the office which have airport cards onboard can see and print from the printer, which is great. The problem is that all of the computers connecting to the network via wires are unable to see the printer (this is under both 10.3.x and 10.4.x, all airport software completely updated.) The Extreme base station shows up for all office computers in their Airport Admin Utility, AND if the printer is connected directly to the Extreme Base Station via USB, all computers can see the printer over Bonjour/Rendevous.
    Anybody have ideas as to how I can get my wired machines to see the printer on the Airport Express?
    Thanks!!

    Applications > Utilities > Airport Admin Utility
    Scan and Select your Airport
    Click Configure
    On the Airport Tab
    Base Station Options...
    Check Enable Remote Printer Access
    iFelix

  • Unable to see the personalization link on any page

    Hi,
    I am unable to see the personalization link on any of my pages (not even on login page).
    I am setting the profile option value to "Yes" for the profile option
    FND: Personalization Region Link Enabled
    Also I have bounced the Apache.
    Please help me as I am stuck due to this.
    Thanks,
    Anoop

    Did you enabled the profile option Personalize Self-Service Defn (FND_CUSTOM_OA_DEFINTION) .It must be set to Yes.
    Abhay

  • Unable to see data in Table in smartform

    Hi all,
    I need to create a smartform where I have to print the header details at the start and then below that details for all line items for a particular document.
    so i have data ;ike :
    Header data :
    field 1 : field 2:
    Field3 : field4:
    field5: field6:
    Item data :
    field1 field2 field3 field4 --> Item 1
    field1 field2 field3 field4 -->Item 2
    field 1 field2 field3 field4 -->Item3
    For the Header data,Im planning to use a template in a secondary window.
    However for the item data,i need to use a table (As i know the no of records only at runtime).Also another reason for usng table would be that I dont need the header on each flloowing page but only the Line item details on the following pages.
    Now my ques is :
    1.I hav ecreated the form and put some constant /texts to just test the form.I am able to see the texts/data in the header data.However  Im unable to see the data for the Item i.e. in the TABLE.
    I have used template for Header details which I can see.
    I dont know what Im doing wrong.Is it because in the DATA tab under TABLES,I have given an interna table but there is no data in the table?
    I have defined only 1 line type in  my table an dthat has 4 cells (as I need to print 4 item fields under the Item data)
    PLease let me know what I am doig wrong because of which Im unable to see the item data in table form.
    Thanks!

    Hi,
    Have you used any exists?
    in exists is there any system date kind?
    Can you try to run your report thru RSRT and use debug option there.
    before reporting please check your all connected targets have data for reporting.
    mean at targets-->request tab, reporting symbol was there or not.
    Any master data objects included in multi provider?
    if yes then please check those, if any ACR was running then it may cause you.
    if possible try to develop simple query with as per needs(mean to see 2015 data only).
    As my guess selections/filters migth be hidden, please check those.
    Thanks

  • Unable to see master data changes

    I added a new field as an Attribute to Master Data (Customer Number) and loaded the data which was successfull. I created an infoset and created a report but am unable to see the values in this new field. I check 'Values in the Infoprovider' on the reports. Also when i go to RSISET and look for Infoset Values I do not see them there.

    Hi,
    I think there are two things you should check:
    1. Have you seen the data for which you added into the attribute in your InfoObject?
    2. Have you seen the field which you added into the attribute in your InfoSet?
    If you got a "NO" answer, you maybe lose step(s).
    Hope above helps you.

  • Unable to see line items in segment clearing account

    Friends,
    Why we are unable to see the line items in intersegment clearing account/zero balance clearing account, eventhough the master is maintained as open item  and line item display.

    Hi,
    I have received the following error message.
    Account 1999990, company code xxxx is clearing account
    Message no. MSITEM111
    Diagnosis
    You have stored account 1999990 in company code xxxx as a clearing account. At the same time, you use line item management with this account.
    System Response
    Error message issued because line item display cannot read data for an account in a ledger if line items exist partially in the entry view together with clearing items for which there are no line items. In such cases, only the data with line items would be selected.
    Procedure
    Check the Customizing settings or account control. Change the settings so that only automatic postings without line items can be made to the account, or select a different account as the clearing account.

Maybe you are looking for