Unable to set the ip address for hosted network client after creating WIFI hotspot

Original Title: INTERNET CONNECTIVITY PROBLEM WITH MY LAPTOP WIFI HOTSPOT
HI all
I am able to use internet connection from my lap hotspot, when the internet source is Public or private wifi.
so I know the cmd window commands for hotspot and settings of client(sharing to hosted network client, assigning IP address etc.,)
but the problem I am facing is slight different
I am using my cdma wireless broadband datacard as my source internet connection(Reliance netconnect +)
when I try to create hotspot for this, as usual I am able to create the hotspot and able to share the internet to hostednework client.
but I am unable to set the ip address for hosted network client, if I try to set ip 192.169.137.1 and 255.255.255.0
as soon as I close the window, the ip address also disappears
when connect my android phone to that hotspot, it is able to connect but there is no internet connectivity.
when I check the hostednetwork client for packet transmission, both sent and received packet is happening., I mean transmitting
so what cause the failure in internet connectivity but success in hotspot connectivity?
check the screen shots...
can u help me..
its little complicated

Hi,
Please make sure the Ad hoc connection IP adress is at the same range with your local connection. In addition, how about recreate the ad hoc connection for test, please have a try.
If problem persists, please use Network troubleshooter in Action Center to fix this problem for test.
Roger Lu
TechNet Community Support

Similar Messages

  • I'm unable to add the email address for iMessage, that I was using before iOS 7 to my iPhone, because it says that it is "in use by another device," but I have no other devices.  How do I resolve this so I can add this email address to my iPhone?

    I'm unable to add the email address for iMessage, that I was using before iOS 7 to my iPhone, because it says that it is "in use by another device," but I have no other devices.  How do I resolve this so I can add this email address to my iPhone to send and recieve iMessages?

    Sync your iPhone to iTunes, and see if that does the trick.  Also you could try a Soft Reset with no Risk to Data.  Holding down both the Sleep button and the Home button until the Apple logo appears and then waiting for the Reset to bring you iPhone back to the lock screen.    Are you trying to add the email at Settings>Messages>Send and Receive from (2 Addresses) your iPhone number and your email address?

  • Unable to set the selected value for a ADF LOV

    Hi,
    I am developing an application using jdeveloper 10.1.3 and Struts.
    I have created a ADF LOV on my JSP Page as given below:
    <html:select property="lob" onchange="javascript:selectLOB(this.form)">
    <html:optionsCollection label="prompt" value="index" property="lob.displayData"/>
    </html:select>
    When i submit the form, i am able to get the value of the selected Value in the List.
    JUCtrlListBinding listBinding = (JUCtrlListBinding) formBean.get("Lob");
    Row r = (Row) listBinding.getSelectedValue();
    String SoLob = (String) r.getAttribute("LobLob");
    But i am unable to set the selected value back in the list when i return to the form again.
    I tried the following:
    int x = listBinding.getSelectedIndex();
    listBinding.setSelectedIndex(x);
    It would be really helpful if some one could let me know what needs to be done.
    Thanks,
    Subashini

    Gyan,
    I tried with the code you suggest , its trying to set the value of a field, but my requirement is to change the property for
    "Rendered" on the field so that based on search parameters we can hide result table column.
    After searching online, I modified the controller code as follows
    1.Created a new transient attribute (Testrender) with type "Boolean" and always updateable.
    2.changed the "Rendered" property value on the field I want to hide as ${oa.PoSearchVO1.Testrender}.
    3. Modified the controller code as follows :
            OAApplicationModule am = pageContext.getApplicationModule(webBean);
            OAViewObject testvo = (OAViewObject)am.findViewObject("PoSearchVO1");
            OADBTransaction txn = am.getOADBTransaction();
            if (testvo != null)
              OARow row = (OARow)testvo.first();
                if (a.equalsIgnoreCase("Approved"))
                     row.setAttribute("Testrender", Boolean.FALSE);
                else
                     row.setAttribute("Testrender", Boolean.TRUE);
            } But now when i run the page and populate the search field and click "Go" its hiding the field but throwing the following error and the search results are also bad.
    Its using only the value of one search parameter but not the second one .
    The search cannot be executed because the table has pending changes that would be lost. I think the vo is getting dirty when I update the transient attribute value. So I used txn.rollback ,then search is working fine but its not hiding the field.
    So can you please let me know how to proceed from here ?

  • Setting the From Address for Reply in Mail

    I am having trouble setting the default “From” address for replies in Mail. When I click on “Reply” the new window opens with a default mail address I do not wish to use. This can be changes by going into the drop down box and setting a different one. This is time consuming and it is easy to send from an inappropriate address.
    “Help” menu says that the default address ( top one in the drop down box) can be changed and gives these instructions:
    Set the From address
    Your messages are sent from the account of the currently selected mailbox. If you have multiple email accounts, you can specify a different account to use for sending all messages, or select an account just for the message you’re writing.
    To specify the account to use for sending all messages, choose Mail > Preferences, click Composing, and then choose an account from the “Send new messages from” pop-up menu.
    To specify an account just for the message you’re writing, click the From pop-up menu, and then choose an email address.&#8232;To change the order in which addresses are listed in the pop-up menu, reorder the addresses in the “Email address” field in the Account Information pane of Mail account preferences.
    When I open the Mail Account Preferences and go to Account Information there is no list of addresses in the “Email address” just the one for the particular account highlighted in the left column eg. “[email protected]” or “[email protected]” .
    I tried to move the order of the accounts in the left hand box but nothing wants to move. Clicking and holding to push one account over another seems not to work.
    Anyone got any ideas on how to fix this?
    NB: This is about "Reply". Default for "New Message" is setting fine.

    i found out how to do this finally!
    1) set up google gmail account to forward your emails to (from the [email protected])
    2) go to your gmail account
    3) go to settings (cog in right hand corner)
    4) go to 'accounts and import'
    5) go to 'send mail as'
    6) click 'Add another email address you own' - add your [email protected] address
    7) google will send a verification email with code to that email address.
    8) enter code
    9) go back to gmail account  >'send mail as' and select 'make default'
    10) close mac 'mail' program and reopen it.
    as long as you have gmail account selected as the primary account in MAIL - mail will now come throught as being sent from that  [email protected] address!!

  • Unable to set manual IP address for VPN connection

    Recently a VPN connection with a client stopped working. They changed phone companies and changed some of the IP addresses.
    After alerting them I could no longer log in, I received the new server address which I can log in with it,
    BUT my computer is assigned a dynamic address that is already in use on their network. This causes my computer to *not* be connected to their network, even though I am inside their firewall; therefore I cannot adjust the database files I need to.
    I have tried to set the VPN (PPTP) connection TCP/IP address IPv4 manually, using the static address they just gave me. But each time I connect, [I believe] their router assigns me an address that is already in use.
    They do not use IPv6.
    Can anyone give me direction on how to make the manual IP address *stick*?
    The tech person at the site keeps telling me it is a problem with my "Mac, because with Windows.... blah, blah, blah".
    I am pretty sure this is not the case and in fact I was the one who let her know I was receiving a duplicate address.
    Your VPN expertise is really appreciated.
    Thanks in advance,
    Michele

    Hi,
    Please make sure the Ad hoc connection IP adress is at the same range with your local connection. In addition, how about recreate the ad hoc connection for test, please have a try.
    If problem persists, please use Network troubleshooter in Action Center to fix this problem for test.
    Roger Lu
    TechNet Community Support

  • Dynamically set the soap address for web services

    Hi,
    I am developing an Oracle J2ee1.3 web service for Oracle application server 10.1.2.
    The web service needs to be deployed on to multiple servers. Hence the host and port for the soap:address needs to be changed for each server.
    Eg: For the 1st server the soap:address is http://www.server1.com/test/MyWebService
    For 2nd server the soap:address is http://www.server2.com/test/MyWebService
    Is there any way to dynamically change this address based on the server the Web Service is deployed to?
    Any help is highly appreciated.
    Thanks,
    Subashini

    It helps to post a link to a thread when you refer to it.  If you are trying to implement that solution though, you can look at the parameter of the corresponding method being called.  The parameter has type 'SIMPLE' which means that it is compatible with all of the predefined elementary ABAP types.  In this case, you should use 'STRING'.

  • Dell 968w..how do I set the IP address for network printing?

    Attempting to connect my Dell 968w to the network for access by my HP and Dell laptops.  Dell said I need an IP address for the printer..how do I set the address??? 

    you need to contact dell printer support for this info...this is usually done by printing a network config page on your printer & you'll see the printer ip address there.
    Note:
    Although I work for HP Imaging & Printing
    Group , I am speaking for myself and not for
    HP.
    Although I am working on behalf of HP, I am speaking for myself and not for HP.
    Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
    If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
    Happy Troubleshooting : )

  • Unable to set the tab order in a form I am creating

    Hello,
    I have a form that I created a bunch of fields for. I did make some of the fields out of order, but was not concerned as I figured I would set the tab order as I have in the past.
    However, for this set of fields, not mater what I do, and how many times I try to set the tab order manually, it skips over a bunch of fields. Even if I try to let acrobat automatically set the tab order, it still doesn't work.
    These fields have been made from scratch as well as, copy and pasted to make sure their properties were all the same, other than a unique name. I can't figure this one out.
    Has anyone ever had this happen to them before?
    thanks!!
    babs

    Hi everyone...thanks!!
    I did check the read only issue first, and that wasn't it... and I made sure they were just text fields and never started out as radio buttons...
    At one poin,t a bad param error popped up..... ah ha!!
    So, I exported the file back to postscript (deleting all the fields first)
    and then made new ones and it worked fine...
    Must have been a corrupted file ;-)
    Thanks for the help!!!!
    babs

  • Error deploying EJB on weblogic: Unable to set the transaction attribute

    Hi,
    I'm trying to deploy an application in WL10.3.2 and an error occurred during activation of changes.
    Here is the error message from the log file:
    <Jun 6, 2011 1:28:27 PM MDT> <Error> <Deployer> <BEA-149205> <Failed to initialize the application 'serverEAR-2' due to error weblogic.application.ModuleException: Exception preparing module: EJBModule(serverEJB-2.8.0.jar)
    Unable to deploy EJB: C:\oracle\Middleware\user_projects\domains\base_domain\servers\Server_3\tmp\_WL_user\serverEAR-2\1zw7ao\serverEJB-2.8.0.jar from serverEJB-2.8.0.jar:
    Unable to set the transaction attribute for method 'saveActionGroup(EditableActionGroup)' on EJB 'ViewBean'. No matching method could be found. Please verify the method signature specified in the ejb-jar.xml file matches that of your Remote interface for this EJB.
    weblogic.application.ModuleException: Exception preparing module: EJBModule(serverEJB-2.8.0.jar)
    Unable to deploy EJB: C:\oracle\Middleware\user_projects\domains\base_domain\servers\Server_3\tmp\_WL_user\serverEAR-2\1zw7ao\serverEJB-2.8.0.jar from serverEJB-2.8.0.jar:
    Unable to set the transaction attribute for method 'saveActionGroup(EditableActionGroup)' on EJB 'ViewBean'. No matching method could be found. Please verify the method signature specified in the ejb-jar.xml file matches that of your Remote interface for this EJB.
         at weblogic.ejb.container.deployer.EJBModule.prepare(EJBModule.java:454)
         at weblogic.application.internal.flow.ModuleListenerInvoker.prepare(ModuleListenerInvoker.java:199)
         at weblogic.application.internal.flow.DeploymentCallbackFlow$1.next(DeploymentCallbackFlow.java:391)
         at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:83)
         at weblogic.application.internal.flow.DeploymentCallbackFlow.prepare(DeploymentCallbackFlow.java:59)
         Truncated. see log file for complete stacktrace
    Caused By: weblogic.ejb.container.deployer.DeploymentDescriptorException: Unable to set the transaction attribute for method 'saveActionGroup(EditableActionGroup)' on EJB 'ViewBean'. No matching method could be found. Please verify the method signature specified in the ejb-jar.xml file matches that of your Remote interface for this EJB.
         at weblogic.ejb.container.deployer.MBeanDeploymentInfoImpl.processCTs(MBeanDeploymentInfoImpl.java:1502)
         at weblogic.ejb.container.deployer.MBeanDeploymentInfoImpl.processSpecificMethodCTs(MBeanDeploymentInfoImpl.java:1472)
         at weblogic.ejb.container.deployer.MBeanDeploymentInfoImpl.initializeTransactionAttribute(MBeanDeploymentInfoImpl.java:773)
         at weblogic.ejb.container.deployer.MBeanDeploymentInfoImpl.<init>(MBeanDeploymentInfoImpl.java:259)
         at weblogic.ejb.container.deployer.EJBDeployer.prepare(EJBDeployer.java:1190)
         Truncated. see log file for complete stacktrace
    Please help me...Thanks.

    In your ejb-jar.xml you are referring to a method saveActionGroup(EditableActionGroup) which is not defined in your remote interface.
    Maybe you have made some typo in the configuration. Check your transaction section, i.e.,
    <container-transaction>
                <method>
                    <ejb-name>ViewBean</ejb-name>
                    <method-name>saveActionGroup</method-name>
                    <method-params>
                        <method-param>package.EditableActionGroup</method-param>
                    </method-params>
                </method>
                <trans-attribute>Required</trans-attribute>
    </container-transaction>or something similar. See if the defined methods are corresponding to the methods defined in the remote interface.

  • SharePoint 2013 Workflow - Change the From Address for an email

    Hello
    I am creating a SharePoint 2013 Workflow Manager Workflow to send out an email when a document is uploaded to a document library. I want to set the From address for the Email activity added to my Workflow. There is no option in Properties to change this.
    This used to be done when creating a SharePoint 2010 workflow in Visual Studio 2012.
    How can I add a From email address for my workflow?
    Thanks
    Yoshi

    Having problems getting SPD 2013 installed on my laptop because of a trial of O365, but I know in SPD 2010 you could find the BCC fields, etc... in the Advanced properties, it wasn't directly available via the common interface.  I know 2013 is very
    different from 2010, and if I can get it to install correctly, I will update, but look for an advanced property, or an XML view where you can find the FROM: field.

  • Hi i use iphone 4 with iso 6.1.3!! Am not getting an option to register my phone number in imsg!! Am just getting an option to set my email address for sending and receiving the imsgs!! How do i register my phone number??

    Hi i use iphone 4 with iso 6.1.3!! Am not getting an option to register my phone number in imsg!! Am just getting an option to set my email address for sending and receiving the imsgs!! How do i register my phone number??

    Hello Nikkii,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iOS: Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/ts4268
    Troubleshooting telephone-number activation (iPhone only)
    After each step, toggle FaceTime and iMessage off and then on in Settings > Messages and Settings > FaceTime.
    Update to the latest version of iOS.
    Ensure that your iPhone is set to the correct time zone. Tap Settings > General > Date & Time.
    Note: If Set Automatically is on but the incorrect time zone is displayed, turn Set Automatically off and then choose the correct time zone, date, and time. Then turn Set Automatically on again.
    Ensure that FaceTime has not been restricted: Settings > General > Restrictions > FaceTime.
    Verify that you can send SMS messages. You need a valid SMS messaging plan to activate FaceTime.
    Contact your carrier to verify that there are no restrictions or blocks on text messages. Blocks on text messaging will prevent iMessage and FaceTime registration.
    If you are unable to activate iMessage or FaceTime on a device after remote wiping it, wait at least 24 hours and try again.
    If "Waiting for Activation" is displayed, leave FaceTime and iMessage enabled for 24 hours. Toggling FaceTime or iMessage off and on will cause the registration process to start over.
    Best of luck,
    Mario

  • Unable to get the composite instance for the invocation. This could be because instance has not yet been created or because the audit level for the SOA infra has been set to Off

    I am on Oracle 11.1.1.7 BPM suite on W8 64 bit. I can't launch the flow trace and get the error "Unable to get the composite instance for the invocation. This could be because instance has not yet been created or because the audit level for the SOA infra has been set to Off".  I have set the audit level to development at the soa-infra>SOA Administration> Common Properties > Audit level set to development and Capture Composite Instance State is Checked.
    Can somebody advice.
    Thanks

    Can you please confirm me the following steps...
    Log in to the EM console, Expand soa-infra (soa_server1) , go to the partition where your composite is been deployed, Click on your composite, On the right, click on the dropdown Settings and choose Composite Audit Level. you can choose to set the Audit Level for this composite. If you choose Inherit, it will take the settings to what the server is being set to. Otherwise, we can override it by choosing Off, Production, or Development.
    Make sure your setting for that composite is not Off, keep inherit or production or development.
    Thanks,
    N

  • Microsoft Intune was unable to set the desired mobile device policy for one or more users due to the following error: A2CE0100

    Hi!
    We have fatal or critical error message on Microsoft Intune Portal but all agents are working just fine. Before opening support ticket we would like to hear comments from the experts on this forum. We would also like to fix this error before starting to
    manage mobile devices with Intune.
    Error message on Intune Portal:
    "Microsoft Intune was unable to set the desired mobile device policy for one or more users due to the following error: A2CE0100"
    Repeated: 19 times.
    Class: (System) Policy
    Random Fatal error message on C:\Program Files\Microsoft\OnlineManagement\Logs\PolicyAgent.log found from one Windows 8.1 client:
    2015-02-21 08:49:20:704 2852 1ab0 FATAL: DocumentProvider::IndicateToConsumer/pp->ProcessPolicies(NULL, NULL, NULL, NULL) failed with error 0x800704d5.
    That said, we are not facing any specific problem but we would like to find symptom of this repeating error message on Intune Portal . We would appreciate to get any thoughts about this case.
    Br.
    Jukka

    Hi Jukka,
    Mobile policy doesn't apply to clients using the Full Client download.  Please open a support case so the team can assist in further troubleshooting.
    Thanks,
    Jon L. - MSFT - This posting is provided "AS IS" with no warranties and confers no rights.

  • I am trying to setup a new Apple ID but it tells me the email address I want to us is in use even though I have deleted it as the secondary address for mother id

    I Am trying to set up a new AppleID but it tells me the email address I wish to use as the ID is in use.  It was the rescue address for another account but I have deleted that.  What do I need to do to get it to recognise the email address as a new one. I cannot set up iCloud without an ID

    Email addresses can only ever be used once in an Apple ID. They cannot be deleted from one Apple ID and moved to another.

  • Unable to open windows using boot camp.  Get message "The bless tool was unable to set the current boot disk."  Any thoughts, Thank you.

    Unable to open windows using boot camp.  Get message "The bless tool was unable to set the current boot disk."   I am using an Imac , Lion operating system, and Windows 7.  It worked a few days ago.  Any thoughts, Thank you.

    Note that nowhere in the Boot Camp instructions does it tell you to use Disk Utility to format the Windows partition. The Boot Camp Assistant program creates the partition & sets the +partition scheme info+ of the disk as appropriate for the Windows installer but the Windows installer itself is responsible for formatting the new partition with the appropriate +file system scheme+ (NTFS for Windows 7).
    If you follow the instructions in the Boot Camp Installation & Setup Guide to the letter you should have no problems installing Windows.

Maybe you are looking for