Unable to settle the AUC from investment measure
HI everyone,
The user has partially settled the AUC in the year 2008, and booked some amount again in 2009, and he has settled the costs in 2009 in full to FXA category, did not settle the auc in 2008, the auc in the year 2008 is still existing and the order has got locked.
I am trying to change the settlement rule, but it is not taking.
Pls help
Thanks in Advance
Sree
Hi,
Once you do business completion, it is meant that Order has been completed in all aspects, even in FI/CO aspects. So after that, you cant do settlement.
PM Order Business Completion
http://www.sap-img.com/plant/difference-between-pm-teco-business-completion.htm
http://help.sap.com/saphelp_46c/helpdata/en/5b/ae39564b8611d182ba0000e829fbfe/frameset.htm
Regards,
Maheswaran.
Similar Messages
-
AUC from Investment measure can't settle to the completed asset partially.
Dear.
I using IM module and AUC which made from Investment measure.
and I post cost to Investment order and settle to AUC periodically.
Some amount In nvestment order should be tranfer to the completed asset. so remained amount in that should be keep going on.
But, Investment order settlement rule only can be maintained by FULL settlement method.
It means, all amount that accumulated in Investment order must be settled.
What I want to do is the partial amount settle to the completed asset and remains left in investment order.
Of course, this investment order keep its function as collect the amount of AUC.
How can It be?Hi,
Use KOB5 - Give the settlement rule - mention the required amount and asset code
Use KO88 and settle the asset by selecting Settlement Type - Partial Settlement
Regards,
Muralidhar -
Unable to capitalize the AUC from project to Fixed Asset
Dear Experts,
I created AUC automatically from WBS and i have settled that WBS with CJ88. But when i try to capitalize it to Fixed asset via AIBU, i am unable to do it. The system throws the error message as
Line item settlement is not possible for asset MY02 36 0
Message no. AW050
Diagnosis
You want to carry out line item settlement of an asset under construction. This transaction can only be carried out for assets with active line item management.
However, line item settlement is not active in the asset class of asset 36 0 (company code MY02).
If the asset is an asset under construction belonging to an investment measure, then you should carry out the settlement using order or project settlement.
Procedure
Check the setting for 'status of AuC' in the definition of the asset class.
Currently asset class settings was investment measure in "status of AUC". I choose this because i want to create a AUC automatically from WBS. If i choose line item settlement in asset class, then i can't assign that asset class to investment profile which inturn i am unable to create AUC automatically from WBS.
Please help me sort out this issue asap.
Regards
VetriDear Vetri,
The reason for this error is most of the time that the field ANLA-XOPVW for this asset is not flagged. Please check this in table ANLA.
OR
In T.code OAOA check your AuC Asset Class whether your asset class is selected Line Item Settlement. If you have selected Line Item settlement after creating an asset and posting has been alsready done for the asset it won't help you.
The Line Item Settlement indicator should be active when the Asset Master is created and the postings are made to it. If this is the case, reverse the postings made to this asset - Create a New AUC - Make the postings Again - Then try AIAB.
I hope this will clear your conecpt and will help you to solve your issue.
If you have any doubts feel free to share.
Regards,
Pankaj A Bhalerao. -
What is the Differance Between AUC Assets & Investment Measure Assets?
HI,
1. What is the differance between AUC Assets & Investment Measure Assets? How to settle the Investment Measure AUC assets to main asset?
2. When i create the Internal Order, The system should automatically creates the Settlement rule for the AUC asset. I dont want to create settlement Rule Manually.
Kindly help me what should i do if the system wants to create the Settlement Rule Automatically? It would be a great help for me if you can provide some inputs..
Thanks
KishoreHi,
Would like to suggest, if you post this query in Asset Accounting Forum under SDN itself, you would get fast response.
Regards, -
Settle an AuC with investment support
Hello Gurus,
I have the following problem:
I have some AuC with investment support measure assigned.
If I settle the AuC created in prior-years the system settle the costs and the investment support to the final assets but If I try to settle an asset created this year, the system does not settle the investment support to the final asset.
I need that when the asset under construction is created and settled to a final asset (within the same year), the investment support iis posted to the final asset aswell.
Thanks alot for your help.
ChristineNormally settlement needs to be performed twice, if the investment support measure is there.
1) for Investment object to AUC ie WBS / IO to AUC. This called automatic /AUC settlement.
2) From AUC to Final Asset: This is called final / periodic settlement.
But both these settlement needs to be executed with KO88/ CJ88. -
Change auc from investement internal order
hi sap experts,
my client has created one internal order with investment profile and assign in auc and now he wants to change the respective auc from internal order.
for example
They created one Internal order as 70000500 with investment profile
earlier they have assigned auc as 5000035 and now they want to change the auc as 5000044.
i would request to all please guide me how to change the Auc from Internal order .
regards
syamalaHi All
I believe you cannot change the AUC in KO02 transaction once you have already settled.
There is an option Block/Delete but it was greyed (disabled).
Usually you create the investment order (KO01) and soonafter the AUC and they are linked forever, until the full settlement to asset.
Well if you really need to transfer the expense from the original AUC to the other AUC you could try the Line Item Apportinment.
1-Run KO88 to settle all expenses to original AUC.
2-Run KO88, menu Environment - Line Item Apportinment, update settlement rule for preliminary and try.
In my box, it was not allowed to settled for AUC, maybe for your box is configured.
I dont know if maybe by the FI-AA side you can fix it.
Regards -
Unable to get the values from ISearchResultList
Hi,
I am working on KM Indexmanagemnt API for searching with TREX, to build a search similar to msn or google.
I am following the example of Thilo Brandt, and after building the query, I am unable to retrieve the result from ISearchResultList, the results size its displaying is zero. But session.getTotalNumberResultKeys() is retrieving a value 20.
Here is the code I am using, please tell me where I am doing wrong.
public class SearchComponetOne extends AbstractPortalComponent {
public void doContent(IPortalComponentRequest request, IPortalComponentResponse response) {
com.sap.security.api.IUser nwUser =
UMFactory.getAuthenticator().getLoggedInUser();
com.sapportals.portal.security.usermanagement.IUser user = null;
try {
user = WPUMFactory.getUserFactory().getEP5User(nwUser);
} catch (UserManagementException e) {
response.write(e.getMessage());
response.write("<html><head><title>Search</title></head><body>");
ResourceContext c = new ResourceContext(user);
try {
IIndexService indexService = (IIndexService) ResourceFactory
.getInstance()
.getServiceFactory()
.getService(
IServiceTypesConst.INDEX_SERVICE);
SearchQueryListBuilder sqb = new SearchQueryListBuilder();
sqb.setSearchTerm("sap");
IQueryEntryList qel = sqb.buildSearchQueryList();
// get an instance of federated search
IFederatedSearch federatedSearch =
(IFederatedSearch) indexService.getObjectInstance(
IWcmIndexConst.FEDERATED_SEARCH_INSTANCE);
List indexList = new ArrayList();
String index = null;
if (index != null && index.length() > 0) {
// take a specified index from index= parameter
indexList.add(indexService.getIndex(index));
} else {
// take all available indexes
indexList = indexService.getActiveIndexes();
// it is recommended to use a search session object
// for searching execution
ISearchSession session = null;
if (session == null)
session = federatedSearch.searchWithSession(qel, indexList, c);
response.write("Inside doContent session.getNumberResultKeys() => " + session.getNumberResultKeys()); // output as 20
this.renderResultHeader(response, session, indexList);
// get all results from the search session
ISearchResultList results = session.getSearchResults(1, session.getTotalNumberResultKeys());
response.write(" from session => " + results.size() + " and size is : " + results.toString()); // I am getting the results.size() as zero
ThanksI think the problem is UME related. I had the same problem once. Try using a system user for searching, instead of the logged on user.
Like this:
com.sapportals.portal.security.usermanagement.IUser user = WPUMFactory.getUserFactory().getUser("cmadmin_service");
Please reward the points if this helps. -
Unable to access the data from Data Management Gateway: Query timeout expired
Hi,
Since 2-3 days the data refresh is failing on our PowerBI site. I checked below:
1. The gateway is in running status.
2. Data source is also in ready status and test connection worked fine too.
3. Below is the error in System Health -
Failed to refresh the data source. An internal service error has occurred. Retry the operation at a later time. If the problem persists, contact Microsoft support for further assistance.
Error code: 4025
4. Below is the error in Event Viewer.
Unable to access the data from Data Management Gateway: Query timeout expired. Please check 1) whether the data source is available 2) whether the gateway on-premises service is running using Windows Event Logs.
5. This is the correlational id for latest refresh failure
is
f9030dd8-af4c-4225-8674-50ce85a770d0
6.
Refresh History error is –
Errors in the high-level relational engine. The following exception occurred while the managed IDataReader interface was being used: The operation has timed out. Errors in the high-level relational engine. The following exception occurred while the
managed IDataReader interface was being used: Query timeout expired.
Any idea what could have went wrong suddenly, everything was working fine from last 1 month.
Thanks,
RichaNever mind, figured out there was a lock on SQL table which caused all the problems. Once I released the lock it PowerPivot refresh started working fine.
Thanks. -
Unable to upload the PAR from NWDS
Hi ,
I am unable to upload the par from NWDS as it is throwing the error "Unable to upload"
I have done the proxy settings in NWDS.
can any one tell me is there any other settings i have to do in NWDS.
Thanks
AjayHi Ajay,
Have you copied the NWDS installed stuff from other system and working on that?
Anyway, you can go about this way to upload your par.
Goto System Administration -> Support -> portal runtime -> Administration console -> Browse and add your par -> say upload. Thats it and your par is uploaded:-).
Hope it helps.
Regards
Deepa
Pls reward points for helpfull answers. -
Unable to get the response from dynamic partnerlink
Hi
I used dynamic partnerlink, in this i am able to invoke the services dynamcially but i am unable to get the response from the services which i had invoked dynamically. In my dynamic partnerlink wsdl i had included callback binding and call back service in the wsdl you can see them below
<binding name="LoanServiceCallbackBinding" type="tns:LoanServiceCallback">
<soap:binding style="document" transport="http://schemas.xmlsoap.org/soap/http"/>
<operation name="onResult">
<soap:operation soapAction="onResult" style="document"/>
<input>
<soap:header message="tns:RelatesToHeader" part="RelatesTo" use="literal" required="false"/>
<soap:body use="literal"/>
</input>
</operation>
</binding>
<service name="LoanServiceCallbackService">
<port name="LoanServiceCallbackPort" binding="tns:LoanServiceCallbackBinding">
<soap:address location="http://openuri.org"/>
</port>
</service>
please help me on this
thanks
SrikanthHi, thanks for the input
Actually My partnerLink had two messageTypes one for Input message request and the other for the Output message request and for the input message i had used the operation as initiate also for the output messsage type operation as result.For both of them binding is defined.
With these am passing the values from myBPELl to the service which am nvoking dynamically but unable to capture the response the variables are local to myBPEL. -
Unable to get the media from the Endeca Experience manager version 11.0.0
Hi.,
Iam unable to get the media from the Endeca Experience Manager for my endeca app 'CRS'.
I have created the endeca app named 'CRS' using the reference app discover-data-catalog-integration and successfully initialized and indexed.Iam able to see the Indexed data in my endeca_jspref and the configurations in my Experience Manager.
I want to import the media from my experience manager(this is my actual requirement) and for this iam executing the get_media.bat cmd from my application's control folder,the cmd was executing successfully without any errors, but the media folder was not populating with any images that i can see in the Experience manager .Please do the needful to resolve this issue.
ThankYou!!!
C:\>cd Endeca\apps\CRS\control
C:\Endeca\apps\CRS\control>get_media.bat
[07.04.14 11:48:08] INFO: Checking definition from AppConfig.xml against existing EAC provisioning.
[07.04.14 11:48:09] INFO: Updating provisioning for component 'DailyReportGenerator'.
[07.04.14 11:48:09] INFO: Updating definition for component 'DailyReportGenerator'.
[07.04.14 11:48:10] INFO: Definition updated.
[07.04.14 11:48:10] INFO: Exporting resource 'http://localhost:8006/ifcr/sites/CRS/media' to 'C:\Endeca\apps\CRS\control\..\config\media'
[07.04.14 11:48:11] INFO: Finished exporting resource.What media are you trying to import? There won't be any media returned with get_media unless you but media in to begin with using the set_media cmd. However, it's preferable to use the media MDEX rather than storing media in the ECR.
-
Siebel 8.0.0.12 Fix Pack; Unable to get the seed from binary file.
Hello Folks,
Can anyone throw some light into what action is required on my scenario.
I have applied Fix Pack Siebel 8.0.0.12 on top of 8.0.0.11 SBA. After it is appled, I am facing a documented issue within the Release Notes for the 8.0.0.12 Fix Pack
The issue is "UNABLE TO LAUNCH URL AFTER APPLYING SIEBEL 8.0.0.12". I tried the steps given with the MR document, however, I am still having this issue.
I am also not sure what is expected at the step of; Run the following command: seedgeneratorutil myseed.dat abcdef .
It's asking me for a value to enter for seed at command prompt. "Enter the seed":
what I should give here. As an assumption values,I gave SADMIN and tried to launch but still shows up the same error
Please Assit
Steps Details from Release Notes:
UNABLE TO LAUNCH URL AFTER APPLYING SIEBEL 8.0.0.12
Component: Server Infrastructure
Subcomponent: SWSE
Product Version: Siebel 8.0.0.12
Base Bug ID: 11938270
**Users are unable to launch the URL after applying the Siebel 8.0.0.12 Fix Pack.
**Use the following workaround to address this issue:
Navigate to the eappweb/bin directory from the command line on the SWSE installation.
Run the following command:
seedgeneratorutil myseed.dat abcdef
NOTE: In the example, myseed.dat is a filename. You can give any file name you wish.
The myseed.dat file is generated in the eappweb/bin directory.
Edit eapps.cfg to include the following parameters under the SWE section:
seedfile = < complete path for myseed.dat >
Bounce the web server.
(For Linux only) Copy libmod_swe.so from the eappweb/bin folder to the web/ohs/modules folder
Thanks
KumarWilson,
Thanks for your reply.I have repeated the steps and regenerated the error messages.
Browser
Message:
An error occurred while trying to process your request. This error indicates a problem with the configuration of this server and should be reported to the webmaster (along with any errors listed below). We apologize for the inconvenience
Initialization error:
Unable to get the seed from binary file.
Log
2021 2011-09-20 23:23:01 0000-00-00 00:00:00 +0530 00000000 001 003f 0001 09 ss110920_7068 7068 7852 E:\sba80\SWEApp\log\ss110920_7068.log 8.0.0.12 [20444] ENU
ProcessPluginState ProcessPluginStateError 1 000000024e781b9c:0 2011-09-20 23:23:01 7852: [SWSE] Unable to get the seed from binary file.
Eapps.cfg
[swe]
Language = enu
Log = errors
LogDirectory = $(SWSERoot)\log
ClientRootDir = $(SWSERoot)
SessionMonitor = False
AllowStats = true
LogSegmentSize = 0
LogMaxSegments = 0
DisableNagle = False
seedfile = E:\sba80\SWEApp\BIN\80012seed.dat
Thanks
Kumar -
Unable to open the Projects from Project center with the Alias name PWA 2010
Hi,
I am unable to open the Projects from Project center with the Alias name with the server name i am able to open the projects, version is project server 2010,
My system is ABC.DC.IN alias name i have given is DEF.AD.COM
With the system name i can able access PWA and all are working fine.
As i have observed with alias name i can able to login to pwa and all the server setting approval center all are working fine but only in the project center i am not able to open the projects (http://DEF.AD.COM/pwa/ProjectDrillDown.aspx .xxxx) its
is coming in the below of the ie.
But with Alias name these are the issues i am facing,
1.when longing with alias name its asking two times for user name and password
2.when i click on a project from project center its taking some time and asking for user name and password after i enter user name and password "PAGE cannot displayed" error i am getting.
3. I have observed one more thing if click on Project details then only this issue is coming project schedule and project information is also opening with Alias name.
can any one Help me.
Vijay kommireddiHi
Hope the below link will help you.
And also please check the browser which you are using as mostly IE 8.0 won't support, Please try it in IE 9.0 and Chrome.
http://social.technet.microsoft.com/Forums/sharepoint/en-US/c03300d2-2a27-4d5d-b3f6-a3660805e125/alternative-access-mapping-when-accessing-the-site-it-is-asking-for-username-and-password
Thanks
Geeth If you feel that the answer which i gave you is Helpful please select it as Answer/helpful. -
UNABLE TO ACCESS THE INTERNET FROM LOCAL PROVIDER ON A SITE-TO-SITE VPN CONNECTION
Dear All,
I have a site-to-site connection from point A to point B. From point B i am unable to access the internet from local internet provider.
I am trying to ping from 192.168.20.1 the dns 8.8.8.8 but i receive the message "destination net unreachable".
When i run "show ip nat translation" i receive nothing.
The vpn connection is working properly, i can ping the other side 192.168.10/24
Below is the configuration of the cisco router on point B.
dot11 syslog
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.21.254
ip dhcp pool voice
network 192.168.21.0 255.255.255.0
default-router 192.168.21.254
option 150 ip 192.168.5.10
ip cef
ip domain name neocleous.ru
ip inspect name IOS_FIREWALL tcp
ip inspect name IOS_FIREWALL udp
ip inspect name IOS_FIREWALL icmp
ip inspect name IOS_FIREWALL h323
ip inspect name IOS_FIREWALL http
ip inspect name IOS_FIREWALL https
ip inspect name IOS_FIREWALL skinny
ip inspect name IOS_FIREWALL sip
no ipv6 cef
multilink bundle-name authenticated
vty-async
isdn switch-type primary-net5
redundancy
crypto isakmp policy 5
hash md5
authentication pre-share
group 2
crypto isakmp policy 10
encr aes
authentication pre-share
group 2
lifetime 28800
crypto isakmp policy 50
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp key Pb85heuvMde9Wdac5Qohha7lziIf142u address [ip address]
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 10
crypto ipsec transform-set TRANSET esp-aes esp-sha-hmac
crypto ipsec transform-set TRANSET2 esp-des esp-md5-hmac
crypto ipsec df-bit clear
crypto map CryptoMAP1 ipsec-isakmp
set peer [ip address]
set transform-set TRANSET
match address CryptoACL
interface FastEthernet0/0
description Primary Provider
ip address [PUBLIC IP MAIN PROVIDER] 255.255.255.252
ip access-group outside_acl in
ip mtu 1390
ip nat outside
ip virtual-reassembly in
load-interval 30
duplex auto
speed auto
crypto map CryptoCY
crypto ipsec df-bit clear
interface FastEthernet0/1
description TO LAN
no ip address
load-interval 30
speed 100
full-duplex
interface FastEthernet0/1.1
description DATA VLAN
encapsulation dot1Q 20
ip address 192.168.20.254 255.255.255.0
ip access-group inside_acl in
ip nat inside
ip inspect IOS_FIREWALL in
ip virtual-reassembly in
ip tcp adjust-mss 1379
interface FastEthernet0/1.2
description VOICE VLAN
encapsulation dot1Q 21
ip address 192.168.21.254 255.255.255.0
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn incoming-voice voice
no cdp enable
interface FastEthernet0/3/0
no ip address
ip access-group outside_acl in
ip nat outside
ip virtual-reassembly in
shutdown
duplex auto
speed auto
crypto map CryptoCY
ip local pool VPNPool 192.168.23.2 192.168.23.10
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list nat_list interface FastEthernet0/3/0 overload
ip route 0.0.0.0 0.0.0.0 [default gateway ip]
ip access-list standard VTY
permit 192.168.20.0 0.0.0.255
ip access-list extended CryptoACL
permit ip 192.168.20.0 0.0.0.255 192.168.3.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.5.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.6.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.12.0 0.0.0.255
permit ip 192.168.21.0 0.0.0.255 192.168.2.0 0.0.0.255
permit ip 192.168.20.0 0.0.0.255 192.168.10.0 0.0.0.255
permit ip host 192.168.22.1 192.168.5.0 0.0.0.255
permit ip host 192.168.20.1 192.168.5.0 0.0.0.255
permit ip host 192.168.22.1 192.168.6.0 0.0.0.255
ip access-list extended DFBIT_acl
permit tcp any any
ip access-list extended inside_acl
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.35
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.39
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.23
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.18
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.55
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.144
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.146
permit ip 192.168.20.0 0.0.0.255 host 192.168.10.141
permit ip host 192.168.20.253 host 192.168.3.21
permit ip host 192.168.20.254 host 192.168.3.21
permit ip 192.168.20.0 0.0.0.255 host 192.168.3.10
permit ip 192.168.20.0 0.0.0.255 host 192.168.20.254
ip access-list extended nat_list
deny ip host 192.168.20.254 192.168.10.0 0.0.0.255
deny ip host 192.168.20.254 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.3.0 0.0.0.255
deny ip host 192.168.20.1 192.168.10.0 0.0.0.255
deny ip host 192.168.20.2 192.168.3.0 0.0.0.255
deny ip host 192.168.20.2 192.168.10.0 0.0.0.255
permit ip host 192.168.20.1 any
permit ip host 192.168.20.2 any
permit ip host 192.168.20.254 any
ip access-list extended outside_acl
permit gre any host [ip address]
permit esp any host [ip address]
deny ip any any
ip sla 2
icmp-echo 192.168.10.254 source-interface FastEthernet0/1.1
frequency 180
timeout 500
ip sla schedule 2 life forever start-time now
logging 192.168.3.21
route-map DFBIT_routemap permit 10
match ip address DFBIT_acl
set ip df 0
route-map ISP2 permit 10
match ip address nat_list
match interface FastEthernet0/3/0
route-map nonat permit 10
match ip address nonat_acl
route-map ISP1 permit 10
match ip address nat_list
match interface FastEthernet0/0You cannot access internet, because all traffic is tunneled for VPN !!!!
Please see cisco tech documentation and bypass traffic for internet.
eg. if lan traffic is going from site a to site b then through vpn
else
lan traffic to internet (any) should be out thorugh the vpn . -
B2b unable to pick the file from xml gateway
Hi All,
I am taking a scenario where B2B picks the files from xml gateway and drop the files in FTP folder. I modified the XML gateway inbound and outbound, i has given my user credentials(unmae, host ,pwd ,sid, port). In agreement in the place of internal delivery channel i has given XML gateway outbound.
Still its unable to pick the files from xml gateway.
Clarify my understanding please
While b2b picks the files from xml gateway, It will pick from ECX_Inbound or ECX_Outbound?
Here i am attaching the logs:
2010.01.15 at 07:32:51:101: B2BStarter thread: B2B - (DEBUG) B2BStarter - Context Initialized
2010.01.15 at 07:32:56:366: B2BStarter thread: B2B - (DEBUG) B2BStarter - Start B2B
2010.01.15 at 07:32:56:369: B2BStarter thread: B2B - (DEBUG) B2BStarter - Starting B2B
2010.01.15 at 07:32:56:392: B2BStarter thread: B2B - (DEBUG) B2BStarter - configuration obtained
2010.01.15 at 07:32:56:395: B2BStarter thread: B2B - (DEBUG) B2BStarter - clear global cache
2010.01.15 at 07:32:56:547: B2BStarter thread: B2B - (DEBUG) XEngine not running. So no need to clear cached objects inside XEngine.
2010.01.15 at 07:32:56:821: B2BStarter thread: B2B - (INFORMATION) Repository:print: [0] HL7 over MLLP Exchange
2010.01.15 at 07:32:56:824: B2BStarter thread: B2B - (INFORMATION) Repository:print: [1] EDI X12 over AS1
2010.01.15 at 07:32:56:826: B2BStarter thread: B2B - (INFORMATION) Repository:print: [2] Custom Document over Generic Exchange
2010.01.15 at 07:32:56:829: B2BStarter thread: B2B - (INFORMATION) Repository:print: [3] EDI EDIFACT over Generic Exchange
2010.01.15 at 07:32:56:832: B2BStarter thread: B2B - (INFORMATION) Repository:print: [4] RosettaNet over RNIF
2010.01.15 at 07:32:56:835: B2BStarter thread: B2B - (INFORMATION) Repository:print: [5] EDI X12 over Generic Exchange
2010.01.15 at 07:32:56:837: B2BStarter thread: B2B - (INFORMATION) Repository:print: [6] Custom Document over MLLP Exchange
2010.01.15 at 07:32:56:840: B2BStarter thread: B2B - (INFORMATION) Repository:print: [7] Custom Document over AS1
2010.01.15 at 07:32:56:842: B2BStarter thread: B2B - (INFORMATION) Repository:print: [8] EDI EDIFACT over AS1
2010.01.15 at 07:32:56:845: B2BStarter thread: B2B - (INFORMATION) Repository:print: [9] HL7 over Generic Exchange
2010.01.15 at 07:32:56:848: B2BStarter thread: B2B - (INFORMATION) Repository:print: [10] Custom Document over Internet
2010.01.15 at 07:32:56:851: B2BStarter thread: B2B - (INFORMATION) Repository:print: [11] Custom Document over ebMS
2010.01.15 at 07:32:56:853: B2BStarter thread: B2B - (INFORMATION) Repository:print: [12] EDI X12 over Internet
2010.01.15 at 07:32:56:856: B2BStarter thread: B2B - (INFORMATION) Repository:print: [13] EDI EDIFACT over Internet
2010.01.15 at 07:32:57:649: B2BStarter thread: B2B - (DEBUG) Repository:constructCertSQL SELECT cert.ID, cert.CLASSTYPE FROM TIP_Certificate_ra cert, TIP_Party_ra party, TIP_DocumentExchange_ra docex WHERE cert.ID = docex.signingcredential AND cert.tradingpartner = party.ID AND party.ishosted != 'Y'
2010.01.15 at 07:32:57:785: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.document.custom.CustomDocumentPlugin:initialize Enter
2010.01.15 at 07:32:58:077: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.document.custom.CustomDocumentPlugin:initialize Exit
2010.01.15 at 07:32:58:824: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize Enter
2010.01.15 at 07:32:58:827: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize resetListener = true
2010.01.15 at 07:32:58:831: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize initdcx = true
2010.01.15 at 07:32:58:891: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize initialize TPAProcessor
2010.01.15 at 07:32:59:010: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize Clear TPA Cache
2010.01.15 at 07:32:59:013: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize initialize DataContext. Pool Size 0
2010.01.15 at 07:32:59:038: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:initialize Treat Response as Request = false
2010.01.15 at 07:32:59:041: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:initialize Exit
2010.01.15 at 07:32:59:043: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize initialize Transport
2010.01.15 at 07:32:59:046: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.transport.TransportInterface:initialize Initialize Transport Logger.
2010.01.15 at 07:32:59:059: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.transport.TransportInterface:initialize Transport LogLevel = ERROR
2010.01.15 at 07:32:59:294: B2BStarter thread: B2B - (DEBUG) Repository:Repository:getDeliveryEndPointList() Wallet Location /apps/elshad4/aelshad4/elshad4_OracleB2B/Apache/Apache/conf/ssl.wlt/default/ewallet.p12
2010.01.15 at 07:32:59:297: B2BStarter thread: B2B - (INFORMATION) Repository:getDeliveryEndPointList: No Archive dir
2010.01.15 at 07:32:59:300: B2BStarter thread: B2B - (INFORMATION) Repository:getDeliveryEndPointList: marker :false
2010.01.15 at 07:32:59:314: B2BStarter thread: B2B - (INFORMATION) Repository:getDeliveryEndPointList: Putting ftp://elshad1.emerson.com//ftpdata/elshad1/ice/infile/850/PO
2010.01.15 at 07:32:59:322: B2BStarter thread: B2B - (INFORMATION) oracle.tip.adapter.b2b.transport.TransportInterface:initialize: Props: ftp://elshad1.emerson.com//ftpdata/elshad1/ice/infile/850/PO file.receiver.wallet_location = /apps/elshad4/aelshad4/elshad4_OracleB2B/Apache/Apache/conf/ssl.wlt/default/ewallet.p12
file.receiver.wallet_password = *****
file.receiver.polling_interval = 5
file.receiver.path = /ftpdata/elshad1/ice/infile/850/PO
file.receiver.marker = false
marker = false
ccc = false
file.receiver.channel_mask = None
file.receiver.minimum_age = 0
filename_format = %FROM_PARTY%_%TIMESTAMP%.dat
file.receiver.van = false
file.sender.channel_mask = None
file.receiver.user = eiced1
PROTOCOL_ENDPOINT = null
file.receiver.password = *****
file.receiver.preserve_filename = false
transport_callout_waittime = 30
preserve_filename = false
file.receiver.ccc = false
van = false
polling_interval = 5
2010.01.15 at 07:32:59:491: B2BStarter thread: B2B - (DEBUG) initialize TransportReceiver: [Emerson_Robin_FTP_TransportServer < ftp > < Emerson >]
2010.01.15 at 07:32:59:858: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.transport.AppTransportInterface:initialize Initialize AppTransport Logger.
2010.01.15 at 07:32:59:864: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.transport.AppTransportInterface:initialize AppTransport LogLevel = ERROR
2010.01.15 at 07:32:59:949: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 07:32:59 GMT+00:00 2010 Outbound - initialize
2010.01.15 at 07:32:59:953: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 07:32:59 GMT+00:00 2010 Obtaining outbound connection...
2010.01.15 at 07:32:59:956: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 07:32:59 GMT+00:00 2010 outbound connect string: jdbc:oracle:thin:@essdbdu31.emrsn.com:36001:ROBIND1
2010.01.15 at 07:32:59:960: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 07:32:59 GMT+00:00 2010 outbound username: apps
2010.01.15 at 07:33:04:319: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 07:33:04 GMT+00:00 2010 Outbound - initialize exit
2010.01.15 at 07:33:04:322: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:startListen Enter
2010.01.15 at 07:33:04:326: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:startListen Exit
2010.01.15 at 07:33:04:329: Thread-10: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:run Thread start
2010.01.15 at 07:33:04:332: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize Exit
2010.01.15 at 07:33:04:335: B2BStarter thread: B2B8:15:32:157: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:32 GMT+00:00 2010 inbound username: apps
2010.01.15 at 08:15:33:757: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:33 GMT+00:00 2010 inbound initialize exit
2010.01.15 at 08:15:33:761: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:33 GMT+00:00 2010 Outbound - initialize
2010.01.15 at 08:15:33:764: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:33 GMT+00:00 2010 Obtaining outbound connection...
2010.01.15 at 08:15:33:767: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:33 GMT+00:00 2010 outbound connect string: jdbc:oracle:thin:@essdbdu31.emrsn.com:36001:ROBIND1
2010.01.15 at 08:15:33:770: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:33 GMT+00:00 2010 outbound username: apps
2010.01.15 at 08:15:34:473: B2BStarter thread: B2B - (DEBUG) : Fri Jan 15 08:15:34 GMT+00:00 2010 Outbound - initialize exit
2010.01.15 at 08:15:34:476: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:startListen Enter
2010.01.15 at 08:15:34:479: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:startListen Exit
2010.01.15 at 08:15:34:481: Thread-10: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:run Thread start
2010.01.15 at 08:15:34:484: B2BStarter thread: B2B - (DEBUG) oracle.tip.adapter.b2b.engine.Engine:initialize Exit
2010.01.15 at 08:15:34:487: B2BStarter thread: B2B - (DEBUG) B2BStarter - B2B initialized
2010.01.15 at 08:15:35:928: Thread-10: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:run initialize Enter
2010.01.15 at 08:15:36:132: Thread-10: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:run initialize B2BListen turned off, will not listen on IP_OUT_QUEUE for messages
2010.01.15 at 08:15:36:139: Thread-10: B2B - (DEBUG) oracle.tip.adapter.b2b.data.MsgListener:run start listening on message
regards
cnuAnuj,
The log which i placed on top, thats the complete log and DC log is given below
2010.01.18 at 12:58:06:117: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:11:130: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:16:143: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:21:153: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:26:169: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:31:164: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:36:173: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:41:182: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:46:194: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:51:210: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:58:56:217: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:01:244: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:06:254: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:11:256: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:16:283: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:21:276: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:26:285: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:31:297: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:36:314: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:41:324: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:46:327: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:51:341: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 12:59:56:352: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered.
2010.01.18 at 13:00:01:359: Thread-14: (ERROR) FTPClient.listNames(): unexpected 550 is encountered
Maybe you are looking for
-
XML Data Inserts into Tables???
hi there, will i be able to an insertXML call onto a table wherein i need to just insert a few node values into couple of fields in the table and leave the other fields unpopulated? - aka - i need to grab the node values from the XML file and then st
-
Adding Dimension field ($) in measures (fact) table in logical layer
Hi, I have a field (amount) in the dimension table. I would like to add this field in the fact table at the logical layer. Dimension table and fact table had physical joins. Can I add into fact table and still do aggregation on that field based on th
-
Hi, I am very new to SAP - XI. I want to work with idocs. So please help me how to develop a scenario which is having sender as file adapter and receiver as idoc adapter or vice versa. thank you.
-
Acrobat 8 Slow Encoding from Word, Missing Text in Result!
I am getting so frustrated with Acrobat 8.x.. not only do I have to put up with the 90-second hang after launching ANY PDF doc, but when I author docs out of Word and Quark, many times it takes ten minutes or more to export a 1-page doc and 40% of th
-
String[] sFile = new String [5]; sFile[0]="access_log"; sFile[1]="access_log.1"; sFile[2]="access_log.2"; sFile[3]="access_log.3"; sFile[4]="access_log.4"; how can I put this strings in the vector?