Unable to stack 3750 and 3750X

I am unable to stack the below switches. I am getting error of incompatible software. Please advise. I am trying to add to 3750x which is the higher version.
Switch Ports Model SW Version SW Image
* 2 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
Switch Ports Model SW Version SW Image
* 1 54 WS-C3750X-48P 12.2(55)SE8 C3750E-UNIVERSALK9-M

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
Two additions to what Leo has already noted.
Would suggest moving to (55)SE9, and believe your 3750X will need a IPBase or IPServices license. (I.e. if 3750X is licensed for LANBase, it may not work.)

Similar Messages

Stacking 3750s and Port Channel

We're replacing legacy switches with 3750s in the coming months, and I have a question about stacking and port channel.
The 3750s will be Layer 2 switches, and each will be uplinked via Gigabit fiber to a pair of 6500s acting as Layer 3 distribution switches.
One thing I'm not sure about is if it will be possible to built Port Channel links for 2, 3, or 4 GB across different switches, or if I can only put Port Channels on the same switch. My understanding is with stacking it appears as one big switch and I can built Port Channels however I want, but am not 100% if this design will work.

You can certainly configure EtherChannels across different 3750s in the same stack, thus avoiding your single point of failure by having the aggregate ports all in one switch.
However in the scenario the port channel has to be configured explicitly to ON, PaGP is not supported across stack members.
3750 stack switches appear as a single logical switch with a single management address. From which you can configure all physical ports. It is important to remember that you configure your switch priorities accordingly in order to govern which switch is your master, and also set a secondary.
Regards
Allan.
Please kindly rate this post if you find this information helpful.

Unable to stack movers and edu coupon. Disappointed!

I went to the Bestbuy local store last night and ask them can I use both coupons in the same purchase. They refused that but when I'm trying to search in Bestbuy forum. The are many people have same issue with me. How can I let the manager know that possible? Who the manager can talk with? Thanks. Can I come to the store again and call someone to talk with the manager?
My local store:
1940 N Perkins Road
Stillwater, OK 74075
Phone: 405-332-7739
Email: (removed per forum guidelines)
GEO: 36.142490, -97.054150

Greetings,
I am sorry to hear you were denied the use of these coupons toward your purchase. It would be my pleasure to work to better understand your specific situation and hopefully provide you with the opportunity to take advantage of these great offers.
Recently, there were some changes made to the Movers Coupon program and the necessary steps to redeem this coupon. How did you obtain your Movers Coupon? Additionally, were you provided with any specific explanation by the store associate as to why they were declining the redemption and stacking of these coupons? In the event you hadn’t registered your Movers Coupon using the Activation Code here, this may have been the reason you were unable to use both at that time. Lastly, what was the item you were looking to purchase?
I look forward to your response,
JD|Social Media Specialist | Best Buy® Corporate
Private Message

Unable to stack EDU and Movers coupon - Ann Arbor, MI Store 408

Hi, we just attempted to buy a Macbook Air that was on sale and ran into the issue of the store refusing to accept both coupons. I understand these coupons are supposed to be an exception. Is it possible for someone from corporate to call and talk to the manager? And if so, can I receive the name of the person so I can speak to them directly when I go back? Thank you very much.
Best Buy - Ann Arbor
3100 Lohr Rd
Ann Arbor, MI 48108
Store 408

Hello mordotz12,
The Movers and College Student Deals coupons are an outstanding way to get a great price on products you need for school and after a big move. I was very gratified to read that you attempted to avail yourself of both offers, but mightily dismayed that you ran into roadblocks at your local store. Certainly aggravation and inconvenience were never our goal and I regret that you may have encountered both, not to mention disrespectful associates.
I will be reaching out to the leadership at the store you've mentioned with clarification and instructions for processing these types of transactions. I encourage you to revisit the store at your earliest convenience to make your purchase. If necessary, I recommend speaking to a manager for a smooth and efficient purchase experience -- any one of them should be able to assist.
Please know that I'm very grateful that you wrote to us about your situation.
Sincerely,
John|Social Media Specialist | Best Buy® Corporate
Private Message

Lms 4.0 and stacked 3750 v2

Hi
Lms 3.2 does not support stacked 3750 V2.
You cannot see it on topology map.
Will you be able to see it using LMS 4.
Otherwise when will it be visible
Steve

You do not need to download anything for the topology and inventory and configuration features of LMS, however, for CiscoView, go to Admin > System > Software Center > Device Update, check the box next to CiscoView and download and install all available packages. It's not a bad idea to do that for Common Services, Network Topology Layer 2 Services and User Tracking, Fault Management, and Inventory Config And Image Management, too just to stay up-to-date. However, with 3750s, the sysObjectID is typically the same for all models so unless you need chassis-specific management, features of LMS should just work with them.

Trunk configuration (VTP) between 3750 and 2811

Hi,
I have a stack of 6 Cisco Catalyst 3750G with 6 VLANs acting as a VTP server and want to establish a trunk link to my Cisco 2811 router equiped with a switching module 16 ports. Can I set the 2811 as a VTP client to propagate the VLAN info from the 3750 and configure one of the port on the switching module of the 2811 as a trunk encapsulated DOT1q and will I be able to route to the outside world.
Thank you

I beleive the switching cards support vtp and that should be possible.
Table 2. Features Supported on Cisco EtherSwitch Modules
EtherSwitch Network Modules (NM-16ESW and NMD-36ESW)
EtherSwitch HWICs (HWIC-4ESW and HWICD-9ESW)
EtherSwitch Service Modules (NME-16ES-1G, NME-16ES-1G-P, NME-X-23ES-1G, NME-X-23ES-1G-P, NME-XD-48ES-2S-P, and NME-XD-24ES-1S-P)
VLANs
Multiple VLANs per Switch
Yes (varies by chassis; maximum of 64 on Cisco 3845)
Yes (maximum of 15 on any chassis)
Yes (maximum of 1,024 per switch or stack)
VLANs in 4,000 Range
No
No
Yes
IEEE 802.1Q Tagged and Untagged VLANs
Yes
Yes
Yes (802.1Q and Inter-Switch Link [ISL])
VLAN Trunking Protocol (VTP) Support for Client, Server, and Transparent Modes
Yes
Yes
Yes

Double stack BI and Enterprise portal for SSO

I am in the process of configuring a double stack BI and SAP Enterprise Portal. Both systems are residing on different domains. We want to utilize the standalone SAP Enterprise Portal for our BEx etc. For that I have exchanged certificates between the ABAP and the SAP Enterprise Portal systems and with the help of Support desk tool I have overcome the certificate issues. The RFC connection from ABAP and SAP Enterprise Portal works fine. The Support desk tool is complaining now about the prefix of these two servers. Also when I check the connection testing between these two systems all the messages are correct except for WEBAS connection it complains about the ping service which is already active on ABAP side. For Connectors it complains about SSO which is not detected/complained by the Support desk tool (0.426). I need your advice:
1. Either uninstall the JAVA instance of BI or
2. Make a Federated Portal network by making the BI JAVA as PRODUCER and the SAP standalone as CONSUMER.
The Support package levels are the same as EHP1 SP 7 of both the double stack BI and the standalone Enterprise Portal systems. The source of users are both local to the systems.

answered

I am trying to setup Microsoft office mail and need assistance - I am receiving the error, unable to find server and DNS setting in the Network

I am trying to setup Microsoft office mail and need assistance - I am receiving the error, unable to find server and DNS setting in the Network

Which version of OSX and what email provider are you using.

Having horrible service with 4GLTE I have had 3G for several weeks (I am not the only person I know having this problem), I have reset my network settings and it did not resolve the issue. I am also unable to send SMS and text messages without them eithe

Having horrible service with 4GLTE I have had 3G for several weeks (I am not the only person I know having this problem), I have reset my network settings and it did not resolve the issue. I am also unable to send SMS and text messages without them either failing or not sending at all. Is there an outage in the Cleveland, Ohio area (zip codes 44129, 44134, 44137) or anything else I can do to resolve this issue?

Not that I'm a Verizon employee, but I have experience in the field. An LTE tower will only extend up to, on a perfect day, with no elevation, 6-7 miles. On a typical day, you will be lucky at four (4) miles. The three ZIP codes you've given are all within about a 12 mile radius. That would mean that 2-3 towers are currently down at the same time, and Verizon would know about it within the hour. Being it's Cleveland, I'm sure they would receive numerous calls regarding an outage of that size.
My point is that if you're having issues in all three ZIP codes, chances are it's a phone issue. If you're handset is simply not receiving LTE, but still receiving 3G, that would signify a SIM card issue. You need to get your SIM card replaced.

After updating to Mavericks, I have been unable to update iphoto, and when I attempt to, it says that These apps were already assigned to another Apple ID, and they will be available in that Apple ID's Purchases list.

After updating to Mavericks, I have been unable to update iphoto, and when I attempt to, it says that These apps were already assigned to another Apple ID, and they will be available in that Apple ID's Purchases list. But no other appleID has ever been used on my computer, how could this be resolved?

Contact App Store support. There's a link on the right hand side of the App Store Window. They're the only ones who can sort out account issues.

Oracle.jbo.NoDefException: JBO-29114 ADFContext is not setup to process messages for this exception. Use the exception stack trace and error code to investigate the root cause of this exception. Root cause error code is JBO-25058. Error message parameters

Dear Guru's,
I am not able to solve the above issue for last couple of days.
I am newbie to the webservice
My Issue...
I am using Jdeveloper 11.1.2.4.0 Release 2
1. Using Jdev I built one small Web Service with two methods.
        While testing the Webservice...
               I passed User Id as Parameter and it successfully return the values (user id, user name and description) from fnd_user table
2. I created another application to consume the web service i created.
               1. I added the webservice SOAP and added the method.
               2. Created a jsf page and drag and drop the parameter and return values to the jsf page.
3. While executing the created jsf page I received the error message as below
"oracle.jbo.NoDefException: JBO-29114 ADFContext is not setup to process messages for this exception. Use the exception stack trace and error code to investigate the root cause of this exception. Root cause error code is JBO-25058. Error message parameters are {0=Attribute, 1=UserName, 2=UserName}"
Even I know that this issue is repeated one in our forum, I was not able to solve this issue.
Can anybody help to solve this issue.
Thanks and Regards,
Durai S E

Dear Guru's,
I am not able to solve the above issue for last couple of days.
I am newbie to the webservice
My Issue...
I am using Jdeveloper 11.1.2.4.0 Release 2
1. Using Jdev I built one small Web Service with two methods.
        While testing the Webservice...
               I passed User Id as Parameter and it successfully return the values (user id, user name and description) from fnd_user table
2. I created another application to consume the web service i created.
               1. I added the webservice SOAP and added the method.
               2. Created a jsf page and drag and drop the parameter and return values to the jsf page.
3. While executing the created jsf page I received the error message as below
"oracle.jbo.NoDefException: JBO-29114 ADFContext is not setup to process messages for this exception. Use the exception stack trace and error code to investigate the root cause of this exception. Root cause error code is JBO-25058. Error message parameters are {0=Attribute, 1=UserName, 2=UserName}"
Even I know that this issue is repeated one in our forum, I was not able to solve this issue.
Can anybody help to solve this issue.
Thanks and Regards,
Durai S E

The iTunes on my desktop is no longer recognizing any of my devices (iPads, iPods, or iPhones). I am unable to sync. And when I connect a device I am asked on the device if I "Trust this Computer". When I hit "Trust" nothing happens. Help?

The iTunes on my desktop is no longer recognizing any of my devices (iPads, iPods, or iPhones). I am unable to sync. And when I connect a device I am asked on the device if I "Trust this Computer". When I hit "Trust" nothing happens. Help?

Hello monkeymonkeydo,
To get this fixed use the steps found here:
iPod not recognized in 'My Computer' and in iTunes for Windows
Hope this helps.
~Julian

HT1923 Want to uninstall iTunes and reinstall. Unable to remove Bonjour and Apple folders. Error message that they are in use. iPodService.exe is not running.

Want to uninstall and reinstall iTunes. Ran uninstall for itunes and QuickTime. Unable yo remove Bonjour and Aple program. Error message that they are in use or the folder is open, ipodservice.exe is not running.

" The feature you are trying to use is on a network resource that is unavailable. I tried to uninstall iTunes, and it would not uninstall. It gave me the following message " The path C:\documents and settings\network service\local settings\application data\apple\apple software update\iTunes.msi cannot be found.
Download the Windows Installer CleanUp utility from the following page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
To install the utility, doubleclick the msicuu2.exe file you downloaded.
Now run the utility ("Start > All Programs > Windows Install Clean Up"). In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

Please Help, After Kernel panic restart failed- apple swirl(6 hrs), SafeMode-failed, SUMode-sucess. Could not unmount disk to erase. Repair permissions-multiple fail errors:unable to set permissions on... unable to set owner and group...

Please Help, I deleted an account that was the same name as the administrator but was not the administrator. Also a samsung galaxy s phone was charging through the usb port.
I closed out a program and got a message that the temp file could not be stored/saved.
Then a Kernel panic message occurred and restart was necessary.
The restart resulted in the screen with the apple logo and a continous swirl for 6+hrs,
Attempted Safe Mode start up, unsuccessful,
Single User Mode-sucess.
Ran $ fsck_hfs -rfd /dev/disk0s2 Ran several times repairs made with one which remained. something about a node.
No change in start up attempts
Started with install CD matching current OS 10.6
Ran Disk Utility Repair Permissions resulting in multiple errors:
One line/error
Warning: SUID file /////Ardagent has been modified and will not be repaired
144 lines/errors of this type of series of lines
Group permissions differ on...should be drwxr-xr-x, they are -rw-r--r-- .
permissions differ on...should be drwxr-xr-x, they are -rw-r--r-- .
unable to set owner and group...error 22: Invalid Argument
unable to set permissions on...error 22: Invalid Argument
Ran Repair Disk, result:
Error: Could not unmount disk (in red)
Ran Verify Disk, result:
The volume HD appears to be ok (in green)
Next I attempted to erase the dist to start from scratch since I have data backed up on time machine.
Error message box
Volume Erase failed
Volume Erase failed with error:
Could not unmount disk
I am looking to solve without buying DiskWarrior unless only resort.

So it looks like solved it for now I will update later. What I did was after starting from the install cd for the 10.6 system I ran from terminal ran:
diskutil disablejournaling /dev/disk0s2
diskutil disableownership /dev/disk0s2
diskutil repairPermissions /dev/disk0s2
then i closed terminal and then when to disk utility and chose to repair disk with results all was fine. Then ran repair permissions and got similar results from terminal function next I erased disk and then chose to restore from time machine and it is now restoring! yea!

I am attempting to upgrade from Adobe Premier Elements 9 to Adobe Premier Elements 13 after using 13's trial version for a few weeks. I am unable to find where and how to do this without losing the project I have been working on. Please help?

I am attempting to upgrade from Adobe Premier Elements 9 to Adobe Premier Elements 13 after using 13's trial version for a few weeks. I am unable to find where and how to do this without losing the project I have been working on. Please help?

Vere Clarke
Premiere Elements 9.0/9.0.1 and Premiere Elements 13 are standalone products.
So, you can have both on the same computer, but only open one for your work.
The classical recommendation is to finish a project in the version in which it was created since there
is no guarantee that a project from an earlier version will open in the later version. Probably will, but
no guarantees. And, when you do explore this, do it from a copy of the earlier version project. Once you
take the earlier version project into a later version one, you cannot go back to edit the later version edited
project in the earlier version program.
If you have both versions (9 and 13) on the same computer and you have not moved, deleted, renamed any of the version 9's files/folders,
right click the saved closed Premiere Elements 9.0/9.0.1 project file, select Open With, and then Adobe Premiere Elements 13.
(Your 9.0/9.0.1 saved closed project file should be found in Libraries/Documents/Adobe/Premiere Elements/9.0.)
Please review and consider. If any questions or need clarification, please do not hesitate to let me know.
Thank you.
ATR

Unable to stack 3750 and 3750X

Similar Messages

Maybe you are looking for