Unable to update 3510 firmware

I want to upgrade the firmware from 327P to 411 on my 3510 storage array. I installed 113723-10 then ran the s3kdlres which ran then prompted me to run the command: "
sccli 10.10.10.20 download ses-firmware <fn>". I inserted the full path to the SUN411I-3510.bin file that came with the patch in place of <fn> and and ran the command which produced the error:
sccli: download enclosure firmware error: bad firmware data for download.
Can anyone tell me what I'm doing wrong here?
Thanks
jds

HI!
This patch have different firmware for different component.
SUN411I-3510.bin - RAID controller firmware
sesfw_3510_1046.s3r -SES firmware.
You say :
sccli 10.10.10.20 download ses-firmware - donload SES firmware, but say full path to RAID firmware.
Read file README in the patch and do step by step.

Similar Messages

  • Unable to update adata firmware

    hi
    i have recently bought a 60gb sp900 adata ssd.
    it firmware is older that 582 version available on the adata website so i tried to update the firmware.
    i downloaded the needed tool from its website but running as root it doesn't list any drive for me to see.
    i can see the drive in gparted and its unformatted. i dont think i need to format it so the drive is recognize for firmware update right?
    have somebody successfully update this ssd or have info to guide me to solve this?
    my guess is that is kernel issue (only a guess) cause i have recently see more bugs in new kernel versions.
    like usb3 causing kernel ops with my new seagate desktop backup plus drive.
    any help would be appreciated.

    A quick google search indicates that this drive has a sandforce controller.  I had one sandforce drive that I too had been unable to update the firmware on.  I don't know what it was and I never figured it out.  I eventually gave that machine/drive to my brother in law, and so ended up installing windows back on it.  So at that point I was able to update it.
    I do see that there are exe files on the Adata page though.  I wonder if you could just make a freedos usb and run the executables from there?

  • T5120 Jumpstart: unable to update system firmware for automatic reboot

    Hi,
    i'm trying to install a T5120 using the jumpstart framework. During the installation the new boot device should be set but instead i get the information that is was not possible to do so.
    Installing boot information
            - Installing boot blocks (c0t0d0s0)
            - Updating system firmware for automatic rebooting
    WARNING: Could not update system for automatic rebooting
    WARNING: CHANGE DEFAULT BOOT DEVICE
             If you want the system to always reboot Solaris from
             the boot device that you've specificed (c0t0d0s0),
             you must change the system's default boot device using
             the eeprom(1M) command after installing Solaris software.the diag-switch is set to 'false'.
    {0} ok printenv
    Variable Name           Value                          Default Value
    ttya-rts-dtr-off           false                          false
    ttya-ignore-cd           true                           true
    keyboard-layout
    reboot-command
    security-mode           none                           No default
    security-password                                      No default
    security-#badlogins   0                              No default
    verbosity                   min                            min
    pci-mem64?              true                           true
    diag-switch?              false                          false
    local-mac-address?   true                           true
    fcode-debug?            false                          false
    scsi-initiator-id           7                              7
    oem-logo                                                 No default
    oem-logo?                 false                          false
    oem-banner                                             No default
    oem-banner?             false                          false
    ansi-terminal?            true                           true
    screen-#columns       80                             80
    screen-#rows            34                             34
    ttya-mode                 9600,8,n,1,-                   9600,8,n,1,-
    output-device           virtual-console                virtual-console
    input-device              virtual-console                virtual-console
    auto-boot-on-error?  false                          false
    load-base                 16384                          16384
    auto-boot?                 true                           true
    network-boot-arguments
    boot-command          boot                           boot
    boot-file
    boot-device               disk                           disk net
    multipath-boot?         false                          false
    boot-device-index      0                              0
    use-nvramrc?            false                          false
    nvramrc
    error-reset-recovery    boot                           bootDoes anybody have any ideas what the problem could be?
    I browsed several boards and a huge set of websites but did find anything related.

    At the first time yes, because i'm using an extra raid controller. That's because the environment 'boot-device' has to be set to a value different than 'disk'.
    At the end of the jumpstart installation i have to type 'init 6' for reboot manually and the environment 'boot-device' has its default value. Thats why the server isn't boot and fall back to net boot.

  • Unable to update latest firmware of N95

    Hi All,
    I tried to update the latest firmware of N95 through NSU. I got error message as
    nsu_ui_client has encountered a problem and needs to close. We are sorry for the inconveinence.
    My PC details are Win XP - SP 2 and 32-bit
    NSU Version latest : v1.4.0en_us
    Any help...

    Is your iTunes version updated, if not then update it from here ?
    What error do you get when trying to update your iPhone ?

  • E63 unable to update new firmware 500.21.009

    Hi,
    I have nokia e63 current firmware 200.21.012 and im trying to update it to 500.21.009 but when it starts to install it says that nokia software updater has lost connection. i already tried using different usb cable which im sure is working fine but same thing happen.,phone screen turns black and the pc keeps making the beep sound, like a usb device is being plugged and unplugged.
    Attachments:
    Capture.PNG ‏67 KB

    You best ignore these USB messages. Depending on your PC and phone, the update can take some time. Reset the E63 using the 3 finger option and try again.
    /discussions/board/message?board.id=communicators&message.id=43332#M43332
    ‡Thank you for hitting the Blue/Green Star button‡
    N8-00 RM 596 V:111.030.0609; E71-1(05) RM 346 V: 500.21.009

  • Unable to update E63 firmware via Nokia Suite

    Hi,
    I've tried to update my E63 software using Nokia Suite v3.3.86 but in vain.
    The steps I've followed in the 3rd step fo update process (i.e. Install) are as follows with screenshots attached:
    1. It checks for valid installation file (see attached "Installation file validation.png").
    Since the update has been downloaded by it previously, it proceeds to next step.
    2. It starts preparing to install (see attached "Preparing to install.png").
    3. It show USB connection active screen with a windows notification saying "Nokia E63 disconnected via USB" is seen on "Install screen". (see attached "Install Screen.png" for "Install Screen").
    4. Next with the same USB connection active screen, a windows notification saying "Nokia E63 connected via USB" is seen on "Install screen".
    5. The windows notification disappears and the screen is still at the "Install Screen" (see attached "Install Screen.png").
    6. Nothing happens even after waiting for  a long time. Clicking "Next" repeats the above mentioned process from step 2.
    Dialing "*#0000#" gives the following info:
    "500.21.009
    02-06-2010
    RM-437
    (c) Nokia E63-1 (308.06)"
    I'm an advanced computer and mobile user and can perform specific system tasks. If there is any solution to the above issue, please let me know.
    Thanks in advance.
    Regards,
    Amit Kumar Singh
    Solved!
    Go to Solution.
    Attachments:
    Installation file validation.png ‏127 KB
    Preparing to install.png ‏131 KB
    Install Screen.png ‏128 KB

    Well, it was disheartening to see that Nokia didn't provide new NSU direct link. Had to get an older version from non-Nokia site. Though after install it updated itself to a newer version but would've really appreciated if Nokia would've provided NSU as official download.

  • HT1414 i am getting an error message saying unable to update as the firmware file is not compataible .Any solution to this problem

    when i try to update iphone 4 i am getting message saying unable to update  the firmware file was not compataible .
    Any solution to this problem

    If the problem is sending to just one address and it has worked in the past, I don't know if this will work. I posted this to another thread yesterday for someone who had the same problem you are having and it worked for them. You can take a look. This is thread that I found and the words below are the OP's suggested fix.
    https://discussions.apple.com/thread/3048200?start=0&tstart=0
    On the iphone i went  Settings>Mail, contacts calanders>choose relevant account (if you have more than 1)> accountname>accountname> scroll down to 'Outgoing Mail server' and click on SMTP >click on your Primary Server >
    My #Username and Password were showing 'Optional'.  Filled them in with the correct details (email account login) and that fixed problem.

  • RV082 v1 unable to update firmware

    So I have the RV082 router.  I had it with a 1.x version of the firmware for a while and I was able to update to the first 2.x version of the firmware a few months ago. 
    This router is fairly old but works ok.  I like to keep it up to date.  I recall always looking for firmware updates and not seeing any, then out of no where there are 3 updates to the software.  I was able to install the second 2.x version of the firmware.  Now I was trying to catch up and install first: 4.1.1.01 and then 4.2.3.03.
    I have downlodad both files multiple times and have been unable to update the firmware.  It always says secure connection failed. 
    If it helps I am using ubuntu 14.04 and the lates version of firefox 36.x
    I don't know if anyone has had the same issue or if they have any sugestions on how to make this work. 
    I would rather install alternative firmware but since it is an intel chip inside, not many people are writing firmware for a router like this one.  I dropped all of my other linsys/cisco routers (about 6 of them) except this one.
    Any help will be greatly appreciated.

    > I have downlodad both files multiple times and have been unable to update the firmware.  It always says secure connection failed. 
    I hope this is caused by requirement of HW version by these new firmwares. As you mentioned, you owns device with HW version 1. According download page it is clearly stated ("V3 hardware required"), that all never firmware versions than 2.0.2.01 requires HW version 3 of unit. I am afraid there is no newer firmware version for V1 HW version of RV082 than you already have installed.

  • Macbook (late 2006) RSS unable to install SMC firmware update

    Hello,
    I bought my macbook on the 27th of December, and the first week it worked fine. Then started the RSS. I did some googling and found out some stuff about RSS, tried to install the SMC firmware update but it would just tell me that I don't need the update. After two weeks of constant RSS:ing I called applecare and told the guy about the problem, he told me to try to update the SMC and if I can't do it bring it in for service.
    Monday the 15th of January I went to the macstation in downtown Vancouver and told them about the trouble, they tried to boot it, and it actually booted but after like 3 minutes the macbook crashed. For about 10 minutes two guys tried to boot it and so on, but they didn't get it to boot. So they took it in for service and somebody was going to check out the macbook and see if it would need a replacement logic board - which it did. So on Monday they ordered the logic board, and today Monday 22nd of January I got it back. Now the thing that bothers me is that when I now try to update the SMC firmware (my current version is btw 1.13f3) it still just says that This computer does not need this update. oh well - i went to apples support page to try to see if there would be a newer release of the smc and then I noticed that in the bottom of the SMC firmware 1.1 update page it says:
    Note: This update is only or the original MacBook, and will not install on a MacBook (Late 2006).
    Then I really was like W T F?!
    I would assume that people who work for apple would know that the SMC update will not update on a computer from late 2006, but nobody ever mentioned this to me.
    I've now had the computer for about an hour and the CPU temperature is at about 50 degrees celcius, with firefox, msn and a terminal open... about 5% cpu load.
    What I'm really wondering is that is there anyone who has similar problems with a macbook late 2006? I guess I'll just have to see if it works and just like I told the guy at macstation, if it starts RSS:ing again I'll be banging on their door
    macbook 2,1 Mac OS X (10.4.8) rss, unable to install SMC firmware update
    macbook 2,1   Mac OS X (10.4.8)   rss

    See if reviewing the installation instructions provides any help:
    http://www.apple.com/support/downloads/macbookefifirmwareupdate10.html

  • Unable to update or restore Ipod due to firmware not found?

    Can anyone help me? I've had my Video Ipod for about a year and a half and have never had trouble with it until now. I can't update it to the lastest software as a message comes up Unable to update software due to firmware not being found. I tried to resort to restoring it to the original factory settings but I ran into a message that said Unable to restore ipod due to firmware not found. Has anyone else had this problem? Help!!!

    For step-by-step instructions, go here:
    http://docs.info.apple.com/article.html?artnum=304309

  • Rebuild screen freeze - unable to update firmware as not docking. Help please

    Hello, I've got an 8gb Zen.
    Always worked fine til I tried one of those hand crank chargers, since then I turn it on and it will freeze on the rebuilding screen.
    Ran scandisk on it - no joy.
    Wanted to try and update firmware to see if that helped but it will not connect to computer via USB. It will charge from the usb but just not connected, nothing.
    Any help appreciated. Thank you

    QRe: Rebuild screen freeze - unable to update firmware as not docking. Help please? So, it freezes on the rebuilding screen after formatting? It is very odd. Just to make sure... you have formatted (not cleaned up) the device from the Recovery Mode menu, right?
    My only suggestion now is trying to mount the device on another computer (try one with a BSD or Linux operating system) and format it from here. With some luck, you should be able to see it as a new USB dri've. I am suggesting one of these operating systems, as you have a chance to mount your player on them even if it does not boots up properly. (I did it to recover mine just before suspecting there was a discrepancy on the FATs stored of the filesystem.) In your case, you will have a chance to format the device (using a FAT filesystem, of course) from these operating systems. I am, however, surprised to see that the Recovery Mode format function does not do its work on your player.
    If your device does not boot up and freezes on the scanning/rebuilding processes there is a chance you have a problem with your filesystem instead of a fried USB port. So, there is a chance you can fix this device yourself yet.

  • Mnh300 unable to update firmware

    I keep getting error unable to update firmware .... when i clickon the update button...
    any help ? 

    Also, don't forget this little ti-bit on post-firmware update from FAQ.
    22. Why don't I see any changes on the NMH after upgrading the firmware?
    The browser cache needs to be cleared after upgrading the firmware to the NMH. This is essential for new features to appear on the Media Hub's interface. FAQ
    Message Edited by thekochs on 01-09-2010 05:35 PM
    Message Edited by thekochs on 01-09-2010 05:35 PM

  • Satellite Pro A200 (PSAE7): unable to update firmware under Vista

    Hi,
    I tried tp upgrade the firmware of my HD-DVD drive (SD L802B) with the new TO35 firmware, but it is not possible. The upgrade button of that Winvup is not selectable. I had the same problem with an older firmware, but i just thought this was because the firmware was up to date ( notebook is 1 month old).
    Winvup displays my drive as "TOSHIBA DVDW/HD SD-L802B TO01 (10/26/07)". The discription of To35 says, it needs a version of TO33 or T034, is that the problem?
    I got this firmware update form [Link to firmware|http://de.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_drivers_bios.jsp?service=DE&mode=allMachi nes&action=search&teddProduct=737]
    so it should be the right one.
    So what can i do to upgrade my drive? Currently watching a HD DVD is not possible :(
    Thx,
    Holger

    Its not possible to update the firmware on your SD-L802B drive because the firmware released on the Toshiba page was deigned for the TS-L802A drive.
    Don't mix these both drives! It's not the same!
    I found this website about SD-L802B Super-Multi DVD Writer
    http://www.storage.toshiba.eu/index.php?id=3&pid=221
    But according to this page the firmware is not available for this driver ( at this time ?:| )

  • Unable to update firmware on 5230.

    hey, I have a nokia 5230 with the current firmware version V10.0.071.
    As far as I know, there are 2 ways to update the firmware on this phone: directly from the phone and through ovi suite. Neither of these ways work for me.
    firstly on the phone: as far as im aware, there would be an application called SW update in the applications folder on my phone and I could update through that. On my phone there is no such application. When I search for it in help there is an article about it as well as a link to the application but when I try to use the link it says that the application cannot be accessed.
    When I try through ovi suite (I tried version 3.0 and the beta version 3.1) I get a problem as well. I use the softwave update feature and it starts, I choose the software and it backs up my phone and downloads the software. Then when it starts installing, it says 15min remaining, and all of a sudden my phone turns off and doesn't turn back on. Then the installation on ovi suite gets interrupted with a "device recovery" error and tells me that "nokia ovi suite lost connection to your device" and gives me some steps to follow. (remove cable, restart device return cable) then click OK to continue but the same thing happens again. I have tried turning of my comp and removing the phone battery as well as restoring factory settings.
    The main reason I wanted to update my firmware is because most songs in my playlist don't play but the player just skips them (it gives the info about song length)m there are also exclamation marks next to the song icons (the songs worked before).
    This problem seems to have been reset with the factory reset tho however no luck with software.
    Sorry for a lot of text.. And if anyone has any ideas please let me know!

    The songs with the exclamation marks are corrupted files. You need a new card or something, or at least format the thing. If you would look at your song folder in a PC, you would see that the files of the songs with exclamation marks are missing.
    Also, since your memory card is faulty, you should update the device with a formatted card, or the card removed.
    If you find my post helpful please click the green star on the left under the avatar. Thanks.

  • Unable to update my nokia5800XM firmware version 3...

    i have nokia 5800 xpress music mobile & airtel connection.
    now my mobile have v30.0.0.011 ,rm-356.
    i can heaer about v31 realeased.i can try to update my firmware.
    but i cant able to update.software updater shows,my mobile have updated firmware.if i want to reinstall or exit option showed.
    but my friend have v31 on his nokia5800.
               why i cant update my phone software?plz help me,

    Hi all, 
    I'm with the same product code as shyam: 0575590.
    Contacted Nokia several times by email, to know when the update will get released for my product code. They are always forwarding that ready-made answer (Thank you for contacting... we have forwarded your mail to concerned dept... do u know you can update the software yourself.. etc.). Asked in different tones but they are cool like ice. They never give an up-to-point reply but the same old pointless reply every time. 
    I don't know what to do. I may get my phone updated from Nokia Care point but that is not practical for me. Waiting will not be a problem if they can tell a date.
    Please post here if any of you gets any information.
    Thanks,
    Fais. 

Maybe you are looking for