Unable to use my Blackberry Tour in the UK even WITH Global data plan
Hi,
I just flew into the UK and was disappointed to see that my phone service or data service is not enabled.
Prior to flying in(10-12 hours ago) I called Verizon customer service, and validated that I had a Global Blackberry Data Plan, and the customer service rep assured me that my phone will work without any issues once I get into the UK. So I didn't bother taking my "other" older AT&T phone(which I keep just in case) with me.
Now I'm stuck here for 3 weeks without any phone or data service! It's pretty crippling..and the best part is, I'll be charged as per my monthly plan regardless, when I get back.
Any help or suggestions?
I have provided some information below, that may be helpful in using your Blackberry Tour in the U.K.
After steps 1 and 2 below, if you are still receiving a red SOS symbol in the upper right hand corner of the device (your SIM card is either missing out of the device, or it has not been activated on the billing side).
**The steps below are assuming the SIM card and Global plan were already activated.
Step 1. – Ensure your device is set to Global or GSM (I have provided a link below on checking this setting)
http://search.vzw.com/?do=viewdoc&id=24732&p=null
***If it is on Global already, ensure the “Data Services” section are “ON” and select GSM as the Network Technology (3g and 2g is preferred)
***Please note*** you will need to switch it back to Global once you are back in the United States.
Step 2. Try power cycling the mobile network (I have provided a link below)
http://search.vzw.com/?do=viewdoc&id=24687&p=null
**leave the network off for 15-20 seconds and turn it back on.
Step 3. Try a soft reset - Remove the battery off of the device and leave it out for at least 2 minutes. Place the battery back in and wait for the device to fully boot up (it may take 2-5 minutes for the device to fully boot)
Lastly, if you are still getting the SOS symbol in red, you can check to see if your device has a SIM card by doing the following:
http://search.vzw.com/?do=viewdoc&id=30045&p=null
**Use the via device option (if it has an 893144***** number then your SIM card is in the device).
I hope this helps.
Similar Messages
-
My iPhone 4 shows the carrier name, I can go online with my data plan, but there are no bars and I can't make phone calls.
It worked for some time, less than a week, I made phone calls and all, and all of a sudden the problem mentioned above happened. Now I can't make any phone calls. I can go online with it, even with my Data plan, I can go to the app store (of course) but can't make any phone calls.
Please help, this is frustrating.Did you already try the troubleshooting mentioned here? http://www.apple.com/support/iphone/assistant/calls/
Also try to reset the phone by holding the sleep and home button until the Apple lo comes up again. You will not lose any data doing this.
Message was edited by: Ingo2711 -
Error.Unable to use mx:CustomDateTimeAxis to implement the component.
Hello.
I have a modified class DateTimeAxis to show data labels in my own format:
package
import mx.charts.DateTimeAxis;
public class CustomDateTimeAxis extends mx.charts.DateTimeAxis
public function CustomDateTimeAxis()
super();
override protected function formatDays(d:Date, previousValue:Date, axis:DateTimeAxis):String
return d["date"];
In main application:
<mx:Application xmlns:mx="http://www.adobe.com/2006/mxml">
<mx:horizontalAxis>
<mx:CustomDateTimeAxis id="xAxis" dataUnits="days" parseFunction="myParseFunction"/>
</mx:horizontalAxis>
The compiler produces an error:
"Unable to use <mx:CustomDateTimeAxis> to implement the component."
Can you help me. Thank you.The issue is very clear: you are using the wrong XML namespace to add your component. The mx namespace is defined for the Flex SDK, so unless you have a custom build of it then your component isn't in there.
http://livedocs.adobe.com/flex/3/html/help.html?content=intro_3.html -
While using my Blackberry messenger service, the message...
While using my Blackberry messenger service, the message "name" is typing a message gets stuck on my screen and the application freezes up
Hi and Welcome to the Forums!
Anytime random strange behaviors creep in, the first thing to do is a battery pop reboot. With power ON, remove the back cover and pull out the battery. Wait about a minute then replace the battery and cover. Power up and wait patiently through the long reboot -- ~5 minutes. See if things have returned to good operation. Like all computing devices, BB's suffer from memory leaks and such...with a hard reboot being the best cure.
Best!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
Use your BlackBerry smartphone as a tethered modem with a PC
Hello everyone,
Here is some information on how to use your BlackBerry smartphone as a tethered modem with a PC.
Support for Tethered Modem Use - this is a general overview article
Link: www.blackberry.com/btsc/KB05178
Now depending on your BlackBerry smartphone here are two different ways to set up tethering on your BlackBerry smartphone via a USB cable.
Connect a computer to the Internet using a CDMA or EVDO BlackBerry smartphone as a tethered modem.
Link: www.blackberry.com/btsc/KB04664
Connect a computer to the Internet using a GPRS EDGE or UMTS BlackBerry smartphone as a thered modem.
Link: www.blackberry.com/btsc/KB05196
Lastly to set up tethering via Bluetooth take a look at the article below.
How to set up Dial-Up Networking using Bluetooth technology
Link: www.blackberry.com/btsc/KB12544
Enjoy and hope that helps.
-DrP
Come follow your BlackBerry Technical Team on Twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.
Click Solution? for posts that have solved your issue(s)!Though not much help, that's the case.
I work for O2 and asked such a question last year when i got mine, and no go -
I'm trying to use my iPad mini for the first time with a previous apple ID and password but it says "iTunes is not working try again"...it allowed me to download an app on my iPhone using the same apple ID & password but all my apps are in "Waiting Status" on my iPad mini because it says "iTunes is not working"...PLEASE HELP ME NOW!!!
Previous user installed iOS 7 beta on that iPhone.
Take it back and get your money returned. You
are running into a new security feature. Whoever owns
the ID that it is asking for is the only person who can
remove the security. That iPhone is worthless to you. -
I just got an iPad, and am trying to figure out how to get it going. I have an iPhone with a data plan through AT&T. Do I need to set up a separate account for the iPad, or can I use it under my existing data plan?
You need a completely different data plan for your iPad which you set up on the device itself and it is billed to a credit/debit card. You cannot share other plans and the iPad account will not appear on your iPhone or any other AT&T account.
-
Hi everyone! does anyone know how to convert .AVI files for using in iMovie without losing the original clip time and date? Handbrake, MPEG Streamclip and Evon all replace the original timecode with the date of modification. This is very frustrating when you are trying to keep the chronology right. I know that if you upload the files to iMovie from one device the chronology isn't a problem, but I'm adding video files from a couple of iPhones and a couple of camcorders. any help much appeciated.
paulHi everyone! does anyone know how to convert .AVI files for using in iMovie without losing the original clip time and date? Handbrake, MPEG Streamclip and Evon all replace the original timecode with the date of modification. This is very frustrating when you are trying to keep the chronology right. I know that if you upload the files to iMovie from one device the chronology isn't a problem, but I'm adding video files from a couple of iPhones and a couple of camcorders. any help much appeciated.
paul -
Does the iPhone 4s need a data plan inorder for "siri" to work or can you just use your local wifi?
It can use both in all the commercials they are using wifi im trying to find out just how much Siri depends on data but so far I think it mainly uses it to pull info up and for some reason to dictate email but it does work on carrier data I guess it's just slower so you don't neccersarily need a data plan in place or have to dig into it to use Siri If you have wifi close by
-
I just had my logic board replaced. i am now having trouble with using the interent even with a strong connection. all other devices are having no problem with the internet. please help
Test while started in Recovery : if the problem persists, then it likely is a hardware issue.
Resetting the System Management Controller (SMC) probably won't change anything, but you can readily do it before contacting the repairers. -
How do I stop Mavericks from using the Internet, I have a DATA PLAN LIMIT!
Since installing Mavericks on our 2 iMacs our DATA PLAN is overused. Over 1.5 to 2.5 GB PER DAY! This is unacceptable!
How do I stop Mavericks from using the Internet, I have a DATA PLAN LIMIT!
HELP!Have you seen this thread…
https://discussions.apple.com/message/23826437#23826437
The short story is that the new 'certifcate checking' system could be downloading large amounts of data, you can turn it of as follows…
clockworkapps wrote:
Turning off CRL & OCSP checking in the Certificates Preferences in Keychain Access solved the problem.
You can do as others have done, install Little Snitch & use the Network Monitor to view what is happening, that thread has some good advice. http://www.obdev.at/products/littlesnitch/index.html
@Topher, Activity Monitor is a bit pants for tracking processes that respawn or just go away (I assume its because it's an on-demand job, have you got a nice article on 'mach services', Linc confused me !? ).
ocspd seems to do that in my limited testing,
Little Snitch is the easiest way to monitor & you can get away with the free demo for long enough to test if funds are tight. -
Is anyone facing the similar problem of visible lag while opening app with 3G data on? It seems apple has made 5s slow to improve iphone 4 performance.5s was very smooth on 7.0.6 even with 3G data on. Is this a bug? Is apple going to fix this soon?
I have same Problem. I tried all options - Reset All Settings, Erase Content & reset all settings, Upgrated to IOS8.1, Restore using iTune. But problem persists.
When I turn Cellular Data or Wifi ON, then there is a lag while opening the Apps. But If I turn Data/Wifi off, phone becomes super fast. I have checked with my friends. They are not facing this issue. Not sure if Apple know this. -
Global Data Plan not working in the Netherlands
I called customer service a week before my trip and arranged for the $30 "Global Data" plan to begin April 1. I have been unable to get a data connection here in the Netherlands and e-mails to customer service have gone unanswered. I cannot see anything on my account to indicate whether this has ever been activated.
By poking around the settings and setting the data networks to GSM I've been able to see Vodophone, T-Mobile, and KPN listed, but if I try to connect to any of them I get an error that indicates I cannot connect to them.
Can anyone provide some advice on how to get this working? I was really relying on this to help with getting info on places to visit and it's proving a pretty difficult trip when having to rely on free wifi spots to make up for this.roninacolyte,
Greetings from the states! To be honest, the Thunderbolt will not work in Hong Kong. You can check out our trip planner for future reference at http://vz.to/n9PFe9
EvanO_VZW
Follow us on Twitter @VZWSupport -
Does the LG Dare require a data plan?
I have an LG Dare that I would like to use on an existing plan. BUT I dont want to pay for data, so I was wondering since Verizon has changed so much with their plans, does the LG Dare require a data plan in order to use it on my plan? All I use the phone for is calls and unlimited texting, no internet. Why pay for something I will never use?
~ Note: My current phone is the LG EnV 2 (no data required on it)...which died completely on me. Hence why Im wanting to switch to my old phone LG Dare.~
Thanks!@turtlegurl86,
We appreciate you bringing this to the attention of the forum. It is fantastic to see of your proactive nature.
The LG Dare does not require a data package. If you would like to add a data package. The current data option for the device is $10 / 75 MB.
I'm sure you will find this information beneficial. It was a great to hear from you.
YosefT_VZW
VZW Support
Follow us on Twitter @VZWSupport -
The global data plan is a scam.
Bottom line of the story: Your Verizon phone will not work at all either in Europe or in South America.
I called three months ago to ask Verizon if I was going to be able to make phone calls in China. Without asking me, I was added against my consent to the global data plan. When I found out about it reading my next bill, I thought it might be a good thing. After all, I was about to go to Germany and Argentina and it would be nice to have data there. So, I thought of keeping it. However, the plan doesn't work. In fact, the phone doesn't even make regular phone calls in any country except USA, Canada, Mexico, China, India, Israel and a few more. It won't work anywhere in Europe or in South America. The problem is that Verizon phones are CDMA, which is a technology which was fully replaced by GSM in most countries. So, your regular Verizon phone will not work almost anywhere. You could get a special GSM phone for your trips. But besides being a nuisance, it was something I wasn't aware since I didn't even request the service.
How did my story finish? I asked for a refund for the $100 I payed for the three months I was in the plan (somehow I was charged double the first month). I was given $25 back only. I payed $75 and I didn't get a single byte of downloaded data in exchange. I'm switching to either AT&T or T-Mobile next month.commonsense101 wrote:
Best advice I can give any traveler is buy a cheap prepaid phone when you get to your destination
It will save you so much money and so many headaches
That's not bad advice, but if you travel a lot, it makes sense to get a global-capable phone and use local SIMs. That way you get cheap rates but can still use all your nice data features, such as Google Navigation. Until the latest crop of ICS LTE phones, you would need to ask Verizon for an unlock code to use a local SIM. Currently, at least, these phones work without an unlock.
You do have to be careful though, prevent your phone connecting until you replace the SIM with a local one, to avoid data charges simply caused by the phone syncing with email, Play store/Apple Store etc.
Maybe you are looking for
-
How can i connect to remote database from netbeans
Hi, I have got MySQL database server installed and running on a different machine. Is there any way to connect and browse database remotely using netbeans 5.5? I have added connector/driver for that database. i can connect and browse the database wit
-
How to create a popup with link without creating any screen
Hi experts, Is the any function module or way to create a popup with a link inside (for e.g. to forums.sdn.sap.com)? I do not want to create any screen and call that screen. Thanks, Khanh
-
Can the new AppleTV be Velcro mounted?
Since this thing is so small, might it be possible to Velcro mount it to the back of one's TV so it's not even noticeable? It's got no moving parts, does it?
-
HT4044 What is the acceptable number of sub-pixel anomalies in the MacBook 13 inch?
What is the acceptable number of sub-pixel anomalies in the MacBook 13 inch?
-
How to get name or unix id of last switched System Events process?
Hello I am writing a script to be used as an idle function to send a command to a process as soon as it's not frontmost anymore. So far, I can figure how to get the unix id or name of the frontmost process, but not of the previous process . Here is w