Uncheck "Fill screen with one page at a time"

Is it possible to set a javascript to turn off the preference "Fill screen with one page at a time" when entering in Full Screen mode? So that way, it will override Acrobat or Reader application preferences when the PDF is open on users computers.

Everything that's supported is documented here: http://livedocs.adobe.com/acrobat_sdk/11/Acrobat11_HTMLHelp/JS_API_AcroJS.89.768.html
Unfortunately, what you want isn't supported.

Similar Messages

Embed pdf in website, show one page at a time, with forward and back controls?

Hi,
Not sure if this is possible (or if this is the right place to ask), but I need to take a multiple page pdf, embed it in a website so its on the left half of the screen, have it only show one page at a time, and have the forward and back page controls.
Is this possible, and if so, could someone point me in the right direction?

Typically you would save it to a JPeg and post those on the web site. Expecting a PDF to show up depends on the client computer configuration and browser. This is too risky, unless you don't mind getting nasty little notes that it does not work. If you do it with JPegs, then all the browsers I know of can handle it. Then simply put the PDF separately for those who prefer to download the PDF and look at it separately.

My macbook is stuck on a grey screen with language select and every time i click english it brings me back to the same gray page what do i do?

My macbook Pro is stuck on a grey screen with language select and every time i click english it brings me back to the same gray page with language select what do i do? Also i dont have enough monet to go to the apple store to get it fix and another thing this happen after i tried to factory reset it without the disck uising coomans i found on youtube.Lastly befor doing the comands my macbook would open any applications and the finder would just blink on and off on the dock.
Heres the link http://www.youtube.com/watch?v=Q5e5thk0O9o

Shut down your computer and disconnect all peripherals (keyboard & mouse if pertinent) from your computer. Now reboot.
If the Mac starts up normally, shut it down again and then plug in one of the peripherals (keyboard or mouse first) and start up your computer again. If it does so successfully repeat the process, adding one peripheral at a time until your Mac acts up. At that point, disconnect the last peripheral you added, reboot your Mac and search the peripheral vendor's website for an updated driver.
If no driver exists or the problem remain after installing the new driver, try a different cable or a different port on your Mac.
If none of the above works, again disconnect all peripherals from your Mac, hold down the "shift" key to start up in "Safe Boot" mode.
If the Mac starts up correctly, restart without pressing the "shift" key.
If your computer still does not start up properly, shut it down and restart it while holding down the Apple+Option-P-R keys; keep holding "all 4 keys" down until you hear the startup sound "twice."
If none of the above work Disconnect all peripherals from your computer. Boot from your install disc & run Repair Disk from the utility menu. To use the Install Mac OS X disc, insert the disc, and restart your computer while holding down the C key as it starts up.
Select your language.
Once on the desktop, select Utility in the menu bar.
Select Disk Utility.
Select the disk or volume in the list of disks and volumes, and then click First Aid.
Click Repair Disk.
(If Disk Utility cannot repair, you will need a stronger utility (3rd party) - Diskwarrior or Techtool PRO)
Restart your computer when done.
Repair permissions after you reach the desktop-http://docs.info.apple.com/article.html?artnum=25751 and restart your computer.
Remove any 3rd party ram.
Reinstall Leopard - This will install a "fresh" copy Leopard without archiving old system files but leaves the rest of your files in place.
If you still want to restore your computer to factory level...
Start up from your install disc, go to Disk Utility and select the disk and click erase - to securely erase data click Security Options and Erase Free Space which will entirely wipe your disk, overwriting it with zeros so that no data is recoverable.
To restore read the instructions in the Mac OS X v10.5 Leopard - Installation and Setup Guide PDF

How do I make preview show only one page at a time in full screen

When I show a document using full screen (or slideshow) in Preview, it shows two pages at a time. I just want to show one at a time, but can't find anything that lets me specify this. There is no relevant Preference that I can see, and if I check single page in view and then choose full screen or slideshow in view, the first page is displayed fine, but then subsequent pages are displayed two up.

Hi, Eric,
Thanks. It looks like I didn't quite make my question clear enough, though.
I want to show a multi-page document one page at a time. If I open it and choose "full screen" in view, I get the first page showing just fine. But if I then use the arrow to go to the second page, Preview shows two pages (#2 and 3), and then continues to show the rest of the document two pages at a time when I advance using the arrow.
I want to show one page at a time, and be able to advance to the next page using the arrow.
Can I do this in Preview?
Thanks,
Russ

Can i use a 2010 24 led screen with one of the new 2012 macs with thunderbolt technology?

can i use a 2010 24 led screen with one of the new 2012 macs with thunderbolt technology?

Yes. Any standalone display which can be connected to a Mini DisplayPort, with or without an adapter, can be plugged into a Thunderbolt port without any additional adapters.
(65766)

Fill screen with zoom for small photo sizes (as in slideshow)?

Front facing iPhone 4S camera sized photos are too small in iPhoto. Is it possible to set a default to fill screen with zoom for all photo sizes (as in slideshow)? Seems like the old iPhoto worked like this.

That's what I was afraid of! I wish it would still scale photos to fill the window also if they're smaller than the window size (not just 100%), like it used to in older versions of iPhoto. Especially irritating, since the problem photos are from an Apple product, the front facing camera of the iPhone4s. I already added my complaint to "feedback".
Thanks anyway.

How do I maximize a window to full screen with one click?

How do I maximize a window to full screen with one click? Lion 10.7.4.

If it is a full sceen App, some are some aren't, just click the arrow icon in the upper right hand corner.

Can you giv me a brief introduction regarding selection screen with one eg:

Hello
can you giv me a brief introduction regarding selection screen with one eg:

Hi Ranjith,
Selection Screens
Selection screens are one of the three types of screen in the R/3 System, along with dialog screens and lists. You use them whenever you want the user to enter either a single value for a field or fields, or to enter selection criteria.
Function
ABAP programs use screens to obtain input from users. The most general type of screen is a dialog screen, which you create using the ABAP Workbench tools Screen Painter and Menu Painter These tools allow you to create screens for data input and output. However, each of these screens requires its own flow logic.
Defining and Calling Selection Screens
You often use screens purely for data input . In these cases, you can use a selection screen. Selection screens provide a standardized user interface in the R/3 System. Users can enter both single values and complex selections. Input parameters are primarily used to control the program flow, while users can enter selection criteria to restrict the amount of data read from the database. You can create and save predefined sets of input values in the ABAP Editor for any selection screen. These are called variants. Texts on the selection screen are stored as language-specific selection texts in the program text elements. If you start an executable report using the SUBMIT statement, the input fields of the selection screen also serve as a data interface.
Defining and Calling Selection Screens
You define selection screens using ABAP statements in a program. Simple statements allow you to create input fields, checkboxes, and radio buttons, and design the screen layout. If you want to create a screen exclusively for data input, you do not need to create it using the normal dialog programming tools. When you create a selection screen, the system automatically assumes the tasks of the Screen Painter and Menu Painter.
The rules for calling and defining selection screens in ABAP programs depend on the program type:
·         Executable program (type 1) without logical database
You can use a single standard selection screen and as many user-defined selection screens as you wish. The standard selection screen is called automatically when you start the program. User-defined selection screens, on the other hand, are called using the CALL SELECTION-SCREEN statement in a program. The standard selection screen always has the screen number 1000. User-defined selection screens can have any screen number except 1000.
·         Executable program (type 1) with logical database
The standard selection screen for an executable program linked to a logical database is made up of the logical database selections and the program selections.
·         Module pools (type M) and function modules (type F)
You can only use user-defined selection screens in module pools and function modules. These can have any number apart from 1000. You can only call a selection screen from a function module using the CALL SELECTION-SCREEN statement. You can also define selection screens as Subscreens and incorporate them in screens or tabstrip controls.
Hope this is useful.
regards
Ram
Message was edited by:
        Ramanujan Chitrakootam

My mac froze in an application so I shut it down by powering off with button, now when I try to turn it on I have a grey screen with Apple loge and the timer swirling but it doesn't get past this, please help!

I Shut down my Mac by holding in the power button after my iMac froze and now when I try to turn it back it on all I get is the grey screen with Apple loge and the timer and doesn't get any further. I have tried the diagnostic test but nothing was found.

Take each of these steps that you haven't already tried. Stop when the problem is resolved.
To restart an unresponsive computer, press and hold the power button for a few seconds until the power shuts off, then release, wait a few more seconds, and press it again briefly.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If a desktop Mac hangs at a plain gray screen with a movable cursor, the keyboard may not be recognized. Press and hold the button on the side of an Apple wireless keyboard to make it discoverable. If need be, replace or recharge the batteries. If you're using a USB keyboard connected to a hub, connect it to a built-in port.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 11. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider.

Set document to be seen one page at a time but print four to a page?

I would like to create a pdf (from a PowerPoint presentation) so that when it is viewed on the web it is seen one page at a time but when it is printed it prints four to a page. It is possible to put that in pdf document settings or do I have to rely on users to make the four to a page choice themselves when they print?

File > Properties > Initial View
You can set the initial view
From the Advanced tab in the Properties you can set some Printing Defaults, but in AA9 Pro, I do not see Tiling as an option. (I believe the powers that be at Adobe thought it best to re-name this feature Banner in AA10. Perhaps it's Poster, I've only seen screen shots of AA10 Print dialog. They've sucessfully dumbed it all down in keeping with Microsoft's current philosophies. Increase font size should soon enough be replaced with "Grow Font")

Full page width then one page at a time, not working as before on new reader

full page tool not jumping screen to use full width.
Then using one page at a time with scroll wheel on mouse not jumping page to page, just scrolling part of page as before.
Don't they check this stuff before a new release?
Running on PC with windows 7 pro

Re: That garbage is unreadable.
If you really want help, stop messing with the fonts and post so that others can read and offer suggestions.
Or better yet... try a search, I'm certain you'll find a solution to whatever issue you're experiencing.
I have found that many times it is the things that make you most angry that push you to action. This was the case here. Thank you for causing me to get so angry that I found the answer myself.

I am trying to print all the PDF pages in a range of 5 pages but can only print one page at a time . . . It will print the current page, but not all or pages 1-5. Can this be overcome?

I am trying to print all the PDF pages in a range of 5 pages but can only print one page at a time . . . It will print the current page only, but not all or pages 1-5. I need to go to the next subsequent page and command to print current page; continuing with this procedure until all pages are printed one at a time. Can this be overcome?

You can use printPages(1, 5), however I need to know how you print current page.

Since the os7 update on my iPad, my safari is not right, it only opens one page at a time, crashes when trying to open more, it has no back button. Help

Since the os7 update on my iPad, my safari is not right, it only opens one page at a time, crashes when trying to open more, it has no back button. Help

Well, I rebuilt the entire workbook... that was a few months ago and so far, the problem hasn't resurfaced. It really wasn't fun to do, but whatever glitch there was in the file, I eliminated it.
I think I should mention that I am using Office v.X, NOT Office 2004. I got a new Intel iMac this week and yesterday when I opened up my files, it opened up the test drive (a JOKE of a program if you ask me) Anyway, some of the very minor issues I had with Office v.X were solved in the 2004 version. (When opening up large multi worksheet files without Excel being already opened, the tabs have white text) Anyway, I am still going to wait for the universal version to come out, but it seems that the newer versions may have fewer glitches (as is to be expected)
At any rate, best of luck to you!

How do I print one page at a time for a photobook .pse project?

I am trying to print a photobook project one page at a time as I am using double sided paper that I need to turn over. One other project I did asked me if I wanted both sides and would I do the turning myself, but this one doesn't. I also wanted no border on the prints and it came out with a border. It is also frustrating to have to wait for it to load 75 pages and then it prints them back to front. Is this PSE or the printer software?

Yes, you can print one page one at time as you want .
In print dialog, select other pages and click on remove button.(refer to screenshot).
For border click on more options and ensure check box is not selected ( refer to screenshot)

Question: Viewing one page at a time

How do I change from viewing a spread as two pages to just viewing one page at a time?

If the doc is set up with spreads then turning spreads off may change the structure of a document. Or, at least, it did back in CS4 when I turned spreads off to look at a document in single-page layout because I was working on a laptop. When I turned spreads back on, lots of features (like anchored objects or text wraps set up to align to spine or "outside edge" for example) were broken.
I never researched any further - I simply got in the habit of exporting PDFs and viewing those in single-page mode, instead of trying to affect layout in InDesign. Maybe this isn't broken anymore, or perhaps there's a non-destructive method of getting a single-page view. Or, more importantly, maybe the document you're looking at doesn't have any of these spread-dependent features. Or maybe you dont need it to keep the spreads features. Anyway, be aware that you might lose something if you untick that box.

Uncheck "Fill screen with one page at a time"

Similar Messages

Maybe you are looking for