Understanding Error Codes
When I try to assign a Virtual inst to a track, I am getting "error -50 returned ny the CoreAudio driver"... what does this mean? Is there a site that list the error codes and their implacations? Help.
You may find the errors listed in the CoreAudio SDK (available from Apple Developer's area).
jord
Similar Messages
-
I was reading a specific channel on a 6025E using the test of the card, i had this error code ;Possible reasons:
NI-DAQ LV: A channel, port, or counter is out of range for the device type or device configuration; or the combination of channels is not allowed; or the scan order must be reversed (0 last).
with a multimeter i can read 1,2V dc at this point (the right voltage). Could you help?
Caroline Paulin
R&D technician
Astroflex inc
CanadaWhat comes to mind first is that your reading is being done in differential mode and you have picked a channel that is out of range. remember that in diff mode the channels are in blocks of 8.
e.g.
0:7
16:23
32:39
if you are in diff mode and try to read channel 9 for example you will get that error.
Dan -
Error code 21 on I tunes recovery
Hi,
I have a Iphone 3 gs, it went into recovery mode, so I logged in to I tunes recovery and my computer crashed!!!
Now when i sync it with I tunes it showes an Iphone connected but no serial number or memory size! also I tryed recovery again and it gets half way through then comes up with error code 21.
!!! Help please!!!Try this support document for understanding error codes http://support.apple.com/kb/ts1275
-
I keep getting this error message when I (right-click) on a photo file on my desktop to burn to a CD. I don't understand this code...does anyone? Thanks Ariel**: The disc can’t be burned because an unexpected error occurred (error code 0x80020000).
I tried every obvious solution to this problem with different types of disc (-R; +R; -RW and +RW) and the problem persisted. Then I read about removing a hyphen in picture filenames. I renamed all the images and bingo there were no further problems. Apple should have solved this by now. This error code has been reported for several years and my MacBook Pro is quite new. Anyway, I hope this helps. It does work.
Piggywiggle -
Iv been having multiple issues with my mac. This comes as a surprise as I rarely use it.
Symptoms-
Clicking noises
Slow
Unresponsive
(Error code 36)
Question mark folder
I used single user mode to try and repair the disk through utilities but the option wasn't available. I then verified the disk and it came up with few error messages
-invalid leaf record count
-invalid directory item
-found corrupt and needs to be repaired
Unfortunately I don't have an instillation disk, I didn't get one when I bought the computer. I don't know what else to do.If the Mac is running v10.7 Lion or v10.8 Mountain Lion ..
Startup your Mac while holding down the Command + R keys so you can access the built in utilities in OS X Recovery
From there you can repair the startup disk. -
okay so a few days ago i received and email for one of my colleagues to do some final editing to a music video. the folder contained 2 videos a rough chops and the main which was about 2-3GB which i dragged on to my external hard drive . and at the time i was trying to install a trial version of parallel lines and me being a newbie to the software i didn't know i need windows installments for it to run lol but yeah... so i was just getting frustrated with the software i kept installing it uninstalling it and then i was thinking my the problem might be because my MacHD space is low (less then 40GBs on my MacHD), so.. i installed it on my hard drive where all my important files are (I'm a graphic designer and do light video editing) video projects and many photoshop projects form 2007 and logs and just a bunch of important files in my hard drive. so because i was so frustrated with the software i wasn't thinking and i installed it on my external 2TB hard drive. and when i realized parallel wasn't working i gave up, uninstalled the program form the hard drive and for some reason when i did that and i tried opening the video my friend had email to me and for some reason it did load up but a few seconds maybe about 10sec in the video is froze and closed my media app (VLC) and when i tried opening other video files it would freeze every few minutes but those specific files i had drag in last were not playing after at least 5 secs and eventually didn't open at all so i restart my computer login and now i get scared i see that my MacBook Pro isn't reading my external hard drive so i search threw forums... i unplug from the wall plug my external hard drive back in my computer and it loaded up but when i opened my external hard drive all my files had that plank white paper icon on my folders (because i have everything organized but subject when you open then drive folder. so... i go in to my projects and nothing, i open my edited photos and nothing... my hart feels like its about to drop and i keep opening files and there is nothing in them, but in "get info" of my drive it shows that there is filled so i go to "disk utility"... i "verify disk" passes ..."repair disk" doesn't past.... i look it up in forums... so i reboot my computer and go to the safe recovery menu. go threw the same ting "disk utility"... verify, pass... repair, pass... so now i feel relieved. i login files in the ext. hard drive load up i tried again to open the files and same thing happens... so now I'm thinking its the files i drag the files to the trash and try to empty and its gone i reboot the computer and my drive didn't load up so i tried unplugin it and back in... drive comes up i notice theres trash.. i tried emptying it and i get the error code -50. and no files are popping up on my external drive and i try to repair/unmount disk and the verify disk doesn't pass and when i click repair disk it doesn't past and another error code pops up -35.... so i felt my drive alone for a few days and yesterday i go the files deleted from the trash and now I'm not getting any codes but when i try to unmount.verify/repair the disk. keeps letting my tits need to be repaired so i click the repair button another error unable to unmount volume to repair...
what do i do? my files still don't show up. and I'm very sorry for the long paragraph but i have to be detailed for you to understand my situationRead this.
-
The Radisson Hotel in Narita Japan uses Guest-Tek as its sign in for guests to access the internet. When I try to log on I first click that I want to use English. The next page has me either agree or disagree to the terms of usage. After I click agree I get a page that says:
Secure Connection Failed
An error occurred during a connection to (website I try)
SSL received a record with an incorrect Message Authentication Code
(Error code: ssl_error_bad_mac_read)
-The page you are trying to view can not be shown because the authenticity of the received data could not be verified
-Please contact the web site owners to inform them of this problem. Alternatively, use the command found in the help menu to report this broken site
(There is a button here that says "Try Again", it does no good)
I don't know who generates this page. Mine is the only computer in the hotel with this problem. I have contacted the web owners via phone who only give me a temporary fix; next time I am there the same problem occurs. I can not find the help menu they reference to report the problem. I'm learning what SSL means, but don't know if I can adjust my security to accept this web site. So far, this is the only place in the world I have problems with this computer and using Firefox. I understand that this may not be a Firefox problem, but any help would be appreciated. I'm rapidly running out of ideas. Thanks, RickFirst, I agree with Karol, use the AUR so that pacman can do its job. Second, when you do your make, there is no reason to run it as root (until you do the make install) For the initial build, it is much safer to not use root; plus all the files in your home directory will continue to belong to use, not to root.
But, try the AUR. -
I get nothing but error messages, -
"Your IMAP server wants to alert you to the following: 113 that mail is not available" or the same with: 364?
Now there are hundreds stacked up on my desktop.
I cannot find the answer anywhere. You need to give answers to how to fix these errors because when I "search" "error code" or the number there is NOTHING. NOTHING! Yet you give us these stupid error codes
then you do not give us ANYTHING on how to fix these. These error codes make me so mad it makes me hate outlook, and hate the developers and hate microsoft. How in the world can you give us ERROR codes without the explanation of what
to do or how to fix it. You need to add each error code number in your "search" then explain what it is and how to fix it. I am not a tech. I am a lawyer. I have googled the entire string of error code and nothing is clear.
So, for the last several years, I get these error codes. Also, there is another error code that won't go away--it is the password error code that asks if I want to store the password. Yes, so I say YES. but it pops back. I am sick of this. This is the reason
I hate Microsoft and I love google. #1 they respond to error, #2 them try to fix them you do not. I paid the full price to buy the OUtlook 2010, almost $500 just to get outlook, and all I got was error codes. I could not even open it because all I would get
was that error codes and NO ONE knew how to fix them. WHAT IS YOUR PROBLEM that you cannot fix the stupid error codes that you imbed? PLEASE HELPHi,
I understand how frustrated you are when facing such an issue, maybe I can provide some suggestions on the problem.
Based on the description, you should be using an IMAP account setup in Outlook. As for the error message, usually it's caused by a corrupted message on the Server. I suggest you logon the Webmail site, check if sending/receiving emails works well.
If you find any unusual emails that cannot be read or sent, try deleting them to try again.
I also suggest you create a new profile to setup the IMAP account:
http://support.microsoft.com/kb/829918/en-us
Contact your Email Service Provider to get the correct and latest account settings, since you have been using Outlook for years, some settings may have been changed while you haven't been informed.
For the steps to setup an account in Outlook 2010, please refer to:
http://office.microsoft.com/en-001/outlook-help/add-or-remove-an-email-account-HA010354414.aspx
I hope this helps.
Regards,
Melon Chen
TechNet Community Support -
DirectAccess Client not connecting without error code on Windows Server 2012 R2 and Windows 8.1
Hello,
we are currently migrating from Windows Server 2012 to 2012 R2 and are not able to get the new Direct Access Service up and running. Our goal is to establish DirectAccess connection for a handful of clients using the IPHTTPS-adapter on the default port 443.
Errors:
There is actually no error showing up. It seems the infrastructure tunnel cannot be created but none of the IPv6-transition adapters is connecting (teredo and 6-to-4 are down) and the IPHTTPs adapter gives no informations about a problem:
>Get-DAConnectionStatus
Status : Error
Substatus : CouldNotContactDirectAccessServer
>Get-NetIPHttpsState
LastErrorCode : 0x0
InterfaceStatus : Failed to connect to the IPHTTPS server; waiting to reconnect
Setup:
Our setup is a virtualized Windows Server 2012 R2 Standard running on Hyper-V. It is located behind a NAT having the Port 443 mapped to the server. The only role installed after the basic install is RRAS including DirectAccess and VPN. The assistants completed
successfully (running the configuration for DirectAccess and VPN). Operation Status says everything is green und working (for multiple days in the meanwhile). A previous direct access installation (on a different machine running Windows Server 2012) has
been removed before installing the new server. The new installation is using a different router, so this might also be the cause of a problem.
The client is a Windows 8.1 notebook located outside the company network accessing the internet through another NAT-device. The client has been able to connect to the previous DirectAccess setup but has never been able to establish a connection after the
setup of the new Direct Access server. The device has no outbound constraints concerning the NAT-device and is only running the integrated Windows Firewall.
Diagnosis:
So far I've done some basic DNS and connectivity checks. The DNS-name can be resolved correctly and the router even responds to pings. The port forward is working and HTTPs connections are generally possible (temporarily routed the port to
access the NLS-Website located on the server, which worked fine).
Network monitor shows that both computers are communicating, traffic on the expected Port 443 is incoming on the server and responses from the server reach the client.
Opening the IPHTTPs-url and in an endless page load. Sometime the browser page closes but I've never seen any result. Using telnet on the port shows that the server is accepting connections. I've even build a small test application that does a GET-Request
on the URL returning HTTP-200 and no content.
I'm currently running out of ideas what to do and since no error occurs this is kind of a bit frustrating. Any help appreciated.
Regards
MatthiasHi,
In addition, have you disabled the DA client components on the DA client? If no, please also check
the settings on the Name Resolution Policy Table.
More information:
DirectAccess
Client Location Awareness – NRPT Name Resolution
In addition, error 0x4C9 means the remote computer refused the network connection. It may be due to the invalid
registry or corrupt drivers. For more detailed information, please refer to the link below:
Error 1225 - Error Code 0x4C9
Note:
Microsoft is providing this information as a convenience to you. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
Best regards,
Susie -
Error Code when trying to burn from a burn folder
Hey everyone,
I am trying to clean up some space on my powerbook G4 (not that I need to) but I like to keep things tidy. I was trying to burn some files onto a CD, it recognized the blank CD, displayed it in my finder as well as the burn icon, I had all the files set up, I hit burn, went to the speed selector, and then when I hit ok an error message popped up saying could not burn "Error Code 0x80020000). Any clue as to why that is? This is the first time I have had a problem burning files, both music and data have worked before.
Thanks for the help.Hi, Joshua.
I presume you are using the internal optical drive that shipped from the factory with your PowerBook G4.
1. You wrote: "I am trying to clean up some space on my powerbook G4 (not that I need to) but I like to keep things tidy."Be careful not to "tidy up" anything outside of your Home folder or the Macintosh HD > Users > Shared folder. Your Home > Library folder is another folder that should not be altered unnecessarily.
"Tidying" System files can render your Mac inoperable unless you either:
• Have a deep understanding of Mac OS X and the files in question.
• Are instructed to remove such a file by someone with such understanding.
2. You wrote: "Error Code 0x80020000)"This is an "Internal Disc Recording" error.
You may have selected too high a speed for the optical media or the optical drive, have bad media, or be using optical media that your optical drive cannot see correctly. Some new, high-speed media use dyes that are problematic with older Mac optical drives. See Macintosh: Factors That Affect Writing to or Reading From Optical Media. If you've not used this brand of media before, try a brand and speed of media that has worked in the past.
Good luck!
Dr. Smoke
Author: Troubleshooting Mac® OS X -
Credential Roaming failed to write to the Active Directory. Error code 5 (Access is denied.)
Hi All,
I could see following error event in all client computers , Could you please some one help me on this ?
Log Name: Application
Source:
Microsoft-Windows-CertificateServicesClient-CredentialRoaming
Event ID: 1005
Level: Error
Description: Certificate Services Client: Credential Roaming failed to write to the Active Directory. Error code 5 (Access is denied.)
Regards, Srinivasu.MuchcherlaIf you are not using certificates and Credential Roaming for clients then simply ignore the error message.
If you are using certificates then you are getting access denied message when Credential Roaming is trying to write to your AD. More details about Credential Roaming here: http://blogs.technet.com/b/askds/archive/2009/01/06/certs-on-wheels-understanding-credential-roaming.aspx
http://blogs.technet.com/b/instan/archive/2009/05/26/considerations-for-implementing-credential-roaming.aspx
This is probably related to the fact that your schema version not 44 or higher: https://social.technet.microsoft.com/Forums/windowsserver/en-US/5b3a6e61-68c4-47d3-ae79-8296cb3be315/certificateservicesclientcredentialroaming-errors?forum=winserverGP
Active Directory
ObjectVersion
Windows 2000
13
Windows 2003
30
Windows 2003 R2
31
Windows 2008
44
Windows 2008 R2
47
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile -
Hello world,
finally, after having been reading here for years I decided to break silence and join the most venerable Apple discussions community!
First of all, I'm no native speaker, so if I at one point don't express myself correctly, I'm sorry. If you don't understand please ask what exactly I meant since it's very important that we know exactly what each one of us is talking about, thank you.
Important, too:
I know there are a lot of posts with this topic and I sifted through a lot of them but none of them captures exactly what my problem or rather my questions are and unfortunately in a lot of them there is no real feedback from the original poster how it all worked out or not. So, I intend this thread to be that one helpful thread which more or less concentrates the knowledge of the other threads, where people with similar problems can go to in future.
I ask one thing of you: Please DON'T answer with just one phrase à la "U got bad RAM, send it back" or "Contact Apple Customer Support Service whatever thingy" without explaining why this would be the only viable option (because I think it is not, at least at the moment).
All the questions I 'd like answered are green, for you to not lose track. I hope this becomes a good discussion so everyone of us can learn a lot!
Following problem:
Initial situation:
My Computer: MacBookPro 8.2, early 2011, 15", 2,2 GHz i7; Mavericks 10.9.5 (yet without this bash fix but ¯\_(ツ)_/¯ )
- Upgraded RAM from onboard 4 (2 x 2) GB to the "unofficially" possible 16 (2 x 8) GB
Ordered RAM on Amazon.de with the right Specs: 204 pin DDR3 SO-DIMM (1333 MHz, PC3-10600S, CL9),
Manufacturer: CSX (http://www.csx-memory.com , while it's maybe not the most renown seller, it was described on another website as reliable )
HERE (hope the link doesn't change): http://www.amazon.de/gp/product/B0084SH6WA/ref=oh_aui_detailpage_o01_s00?ie=UTF8 &psc=1
- Installed it, booted Mac without problem, what does System Profiler say? I have full 16 GB 1600 MHz Memory installed
- Obviously sent me the "wrong" RAM (or can System Profiler be wrong??), funny thing: It works,
--> after a LOT of research checked here http://guides.macrumors.com/Buying_RAM my i7 is 2720QM, so supports it, lucky me
Btw, if i go to About this Mac > more information > memory, the Text there even says it can hold 1600 MHz, has this been written there like this all along?!
- Which RAM do I have installed exactly now? since the sticker on it showed the originally ordered Specs.., moreover how do I determine the CAS latency of my installed RAM?
Crashes:
Didn't really have any, except..... well,
- In some instances Firefox (I think 32.02. or sth., the latest Version at this moment) reproduceably keeps crashing, for example right now, can't even start it, that's why I can't tell you the exact version, maybe I edit that later. Safari so far hasn't crashed.
- Once I had a System Crash, but it happened when I wanted to reboot after updating the firmware of a hooked on external WD drive to be usable again as time machine backup volume under mavericks (without endangering my data).
The RAM seems to work fine; for example when I was doing a long overdue backup of 77GB on said drive, Activity Monitor showed a RAM Usage of 15,99 GB and nothing crashed. Only the fans were powering at some point but i thought that normal..
- Actually produced two more Crashes when trying to run Apple Hardware Test (AHT), the one on the second disc that originally came with my Computer (probably made for OS 10.6.x x= 6 or sth., don't remember which version my MBP was shipped with), which leads to
Tests:
Memtest86
- I put Memtest86 v.5.01 on a USB Stick and bootet from that and let it test "the whole" RAM
(btw Do you know how you can put the bootable USB image of Memtest only to one (of a few) partition of my 32 GB USB Stick? The instructions (command line stuff) only let me put it on the whole Stick which makes it otherwise useless as a volume; ok here I'm not sure if I'm using the correct technical terms....)
- I let Memtest86 do 3 and a half passes with one pass consisting of 10 different tests, so it took over 8 hours!
--> RESULT: 0 (in words: zero) ERRORS,
--> That is why I think my RAM is ok, because I think (think NB, don't know) Memtest86 does good testing,or do you know better?
AHT
- After that, out of curiosity, I tried to run AHT from the DVD with said results, then I ran AHT (also called Apple Diagnostics under Mavericks) from the Internet, this worked, but produced the famous 4MEM/9/40000000 Error Code,
first one for example was: 4MEM/9/40000000: 0x8477df98, the last part after the colon is variable, but stays the same in one instance, i.e. if you repeat the AHT directly. If you restart the Computer an rerun the test then it changes, e.g. some other it showed 0x84770a18
- I did the short and the extended version, it took ca. 2-3 and 16 min respectively till producing the Error Code (only 1 at a time)
- Did it 4 times or so; once in short/simple version it showed no error, the rest the 4MEM/9 s.
some example of a simple test, results taken out of the System Profiler Window (fehlgeschlagen= failed):
Apple Diagnostics:
The usual self test on start up is always passed (bestanden), see for example:
What other than bad RAM can 4MEM/9/40000000 mean? I hope there are a few tech and computer savvy people around this place who know what they are talking about and can give me a good answer, or at least help to narrow it down. Actually I also think, the RAM sticks are not loose, but before I screw open my MBP again I would like to explore the other possibilities.
Is it probable that this Error Code has got sth. to do with me installing a) 16 GB of b) 1600 MHz RAM, or maybe with CAS Latency (i don't know the actual CL of this RAM)? and if so, is it only because some Apple Programmer/Developer/Technician wrote some values in a list on the System Level, so it doesn't accept RAM it would normally work with?? If it works fine and is faster, why change it?
Final Words:
I repeat, apart from the Firefox crashes, my Mac seems to be working fine, at least I don't notice anything, (well, that disk utility and System Profiler (or whatever it's called nowadays) sometimes take time to start up is nothing special i think, is it?)
But now I'm scared that perhaps there could be a future danger for my computer I do not foresee...I hope you can at least exclude that.
So I'd rather spend my time starting a discussion here with people who don't have to abide by some corporate policy (right?) than having the hassle of repeatedly screwing my Mac open and shut and doing expensive calls with all the companies involved who won't tell me anything more in depth than "we have to send it there, do more tests and you get it back then".
I hope that this thread won't rot in the wastelands of unanswered posts and that maybe all the people who take part in it learn sth. and all the people seeking help in future will find it here.
Thanks for your patience!
Waiting for your greatly appreciated answers,
MuddyMic
PS: Why is there no category Hardware, Components, RAM or sth similar? Not sure if it fits in Ports and Interfaces so I put it under Using a MBPHello world,
finally, after having been reading here for years I decided to break silence and join the most venerable Apple discussions community!
First of all, I'm no native speaker, so if I at one point don't express myself correctly, I'm sorry. If you don't understand please ask what exactly I meant since it's very important that we know exactly what each one of us is talking about, thank you.
Important, too:
I know there are a lot of posts with this topic and I sifted through a lot of them but none of them captures exactly what my problem or rather my questions are and unfortunately in a lot of them there is no real feedback from the original poster how it all worked out or not. So, I intend this thread to be that one helpful thread which more or less concentrates the knowledge of the other threads, where people with similar problems can go to in future.
I ask one thing of you: Please DON'T answer with just one phrase à la "U got bad RAM, send it back" or "Contact Apple Customer Support Service whatever thingy" without explaining why this would be the only viable option (because I think it is not, at least at the moment).
All the questions I 'd like answered are green, for you to not lose track. I hope this becomes a good discussion so everyone of us can learn a lot!
Following problem:
Initial situation:
My Computer: MacBookPro 8.2, early 2011, 15", 2,2 GHz i7; Mavericks 10.9.5 (yet without this bash fix but ¯\_(ツ)_/¯ )
- Upgraded RAM from onboard 4 (2 x 2) GB to the "unofficially" possible 16 (2 x 8) GB
Ordered RAM on Amazon.de with the right Specs: 204 pin DDR3 SO-DIMM (1333 MHz, PC3-10600S, CL9),
Manufacturer: CSX (http://www.csx-memory.com , while it's maybe not the most renown seller, it was described on another website as reliable )
HERE (hope the link doesn't change): http://www.amazon.de/gp/product/B0084SH6WA/ref=oh_aui_detailpage_o01_s00?ie=UTF8 &psc=1
- Installed it, booted Mac without problem, what does System Profiler say? I have full 16 GB 1600 MHz Memory installed
- Obviously sent me the "wrong" RAM (or can System Profiler be wrong??), funny thing: It works,
--> after a LOT of research checked here http://guides.macrumors.com/Buying_RAM my i7 is 2720QM, so supports it, lucky me
Btw, if i go to About this Mac > more information > memory, the Text there even says it can hold 1600 MHz, has this been written there like this all along?!
- Which RAM do I have installed exactly now? since the sticker on it showed the originally ordered Specs.., moreover how do I determine the CAS latency of my installed RAM?
Crashes:
Didn't really have any, except..... well,
- In some instances Firefox (I think 32.02. or sth., the latest Version at this moment) reproduceably keeps crashing, for example right now, can't even start it, that's why I can't tell you the exact version, maybe I edit that later. Safari so far hasn't crashed.
- Once I had a System Crash, but it happened when I wanted to reboot after updating the firmware of a hooked on external WD drive to be usable again as time machine backup volume under mavericks (without endangering my data).
The RAM seems to work fine; for example when I was doing a long overdue backup of 77GB on said drive, Activity Monitor showed a RAM Usage of 15,99 GB and nothing crashed. Only the fans were powering at some point but i thought that normal..
- Actually produced two more Crashes when trying to run Apple Hardware Test (AHT), the one on the second disc that originally came with my Computer (probably made for OS 10.6.x x= 6 or sth., don't remember which version my MBP was shipped with), which leads to
Tests:
Memtest86
- I put Memtest86 v.5.01 on a USB Stick and bootet from that and let it test "the whole" RAM
(btw Do you know how you can put the bootable USB image of Memtest only to one (of a few) partition of my 32 GB USB Stick? The instructions (command line stuff) only let me put it on the whole Stick which makes it otherwise useless as a volume; ok here I'm not sure if I'm using the correct technical terms....)
- I let Memtest86 do 3 and a half passes with one pass consisting of 10 different tests, so it took over 8 hours!
--> RESULT: 0 (in words: zero) ERRORS,
--> That is why I think my RAM is ok, because I think (think NB, don't know) Memtest86 does good testing,or do you know better?
AHT
- After that, out of curiosity, I tried to run AHT from the DVD with said results, then I ran AHT (also called Apple Diagnostics under Mavericks) from the Internet, this worked, but produced the famous 4MEM/9/40000000 Error Code,
first one for example was: 4MEM/9/40000000: 0x8477df98, the last part after the colon is variable, but stays the same in one instance, i.e. if you repeat the AHT directly. If you restart the Computer an rerun the test then it changes, e.g. some other it showed 0x84770a18
- I did the short and the extended version, it took ca. 2-3 and 16 min respectively till producing the Error Code (only 1 at a time)
- Did it 4 times or so; once in short/simple version it showed no error, the rest the 4MEM/9 s.
some example of a simple test, results taken out of the System Profiler Window (fehlgeschlagen= failed):
Apple Diagnostics:
The usual self test on start up is always passed (bestanden), see for example:
What other than bad RAM can 4MEM/9/40000000 mean? I hope there are a few tech and computer savvy people around this place who know what they are talking about and can give me a good answer, or at least help to narrow it down. Actually I also think, the RAM sticks are not loose, but before I screw open my MBP again I would like to explore the other possibilities.
Is it probable that this Error Code has got sth. to do with me installing a) 16 GB of b) 1600 MHz RAM, or maybe with CAS Latency (i don't know the actual CL of this RAM)? and if so, is it only because some Apple Programmer/Developer/Technician wrote some values in a list on the System Level, so it doesn't accept RAM it would normally work with?? If it works fine and is faster, why change it?
Final Words:
I repeat, apart from the Firefox crashes, my Mac seems to be working fine, at least I don't notice anything, (well, that disk utility and System Profiler (or whatever it's called nowadays) sometimes take time to start up is nothing special i think, is it?)
But now I'm scared that perhaps there could be a future danger for my computer I do not foresee...I hope you can at least exclude that.
So I'd rather spend my time starting a discussion here with people who don't have to abide by some corporate policy (right?) than having the hassle of repeatedly screwing my Mac open and shut and doing expensive calls with all the companies involved who won't tell me anything more in depth than "we have to send it there, do more tests and you get it back then".
I hope that this thread won't rot in the wastelands of unanswered posts and that maybe all the people who take part in it learn sth. and all the people seeking help in future will find it here.
Thanks for your patience!
Waiting for your greatly appreciated answers,
MuddyMic
PS: Why is there no category Hardware, Components, RAM or sth similar? Not sure if it fits in Ports and Interfaces so I put it under Using a MBP -
SQL Server 2008 KB2977321 Failed with Error code 1642
As part of application of security patches via windows update, sql server KB2977321 was applied along with a number of OS security patches.
Prior to applying the patches, I stopped the agent, engine, reporting, analysis and full text services.
The Sql server build prior to windows update was (for both instances):
ProductVersion
ProductLevel
Edition
10.0.5500.0
SP3
Standard Edition (64-bit)
After the update process, my main instance is showing (the second instance is not in use yet and I have left it in its stopped state)
Microsoft SQL Server 2008 (SP3) - 10.0.5520.0 (X64)
Jul 11 2014 16:11:50
Copyright (c) 1988-2008 Microsoft Corporation
Standard Edition (64-bit) on Windows NT 6.1 <X64> (Build 7601: Service Pack 1) (VM)
In the Administrative Logs after the OS patches were applied (and all were reported as successful by windows update), I found the following errors listed:
Log Name:
Application
Source:
MsiInstaller
Date:
11/18/2014 7:16:45 PM
Event ID:
1024
Task Category: None
Level:
Error
Keywords:
Classic
User:
SYSTEM
Computer:
SJCDB3.intranet.co.st-johns.fl.us
Description:
Product: Microsoft SQL Server 2008 Database Engine Services - Update '{9145CF54-462E-4A28-8FB5-A44C93AD3716}' could not be installed. Error code 1642. Windows Installer can create logs to help troubleshoot
issues with installing software packages. Use the following link for instructions on turning on logging support: http://go.microsoft.com/fwlink/?LinkId=23127
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
<Provider Name="MsiInstaller" />
<EventID Qualifiers="0">1024</EventID>
<Level>2</Level>
<Task>0</Task>
<Keywords>0x80000000000000</Keywords>
<TimeCreated SystemTime="2014-11-19T00:16:45.000000000Z" />
<EventRecordID>1764186</EventRecordID>
<Channel>Application</Channel>
<Computer>SJCDB3.intranet.co.st-johns.fl.us</Computer>
<Security UserID="S-1-5-18" />
</System>
<EventData>
<Data>Microsoft SQL Server 2008 Database Engine Services</Data>
<Data>{9145CF54-462E-4A28-8FB5-A44C93AD3716}</Data>
<Data>1642</Data>
<Data>(NULL)</Data>
<Data>(NULL)</Data>
<Data>(NULL)</Data>
<Data>
</Data>
<Binary>7B38373544383436332D313135422D343444322D414432352D3731454337453833423843437D207B39313435434635342D343632452D344132382D384642352D4134344339334144333731367D2031363432</Binary>
</EventData>
</Event>
In the C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20141118_191448\Detail.txt file I found the following around the time the error was reported
2014-11-18 19:16:30 Slp: Baseline Package Id sql_engine_core_inst_Cpu64 - The highest patch version is 10.3.5500.0
2014-11-18 19:16:30 Slp: Patch Id KB2977321_sql_engine_core_inst_Cpu64 - NotInstalled on the baseline msi package sql_engine_core_inst_Cpu64.
Detail description of this patch package is: PatchId=KB2977321_sql_engine_core_inst_Cpu64 PatchVersion=10.3.5520.0 BaselinePackageId=sql_engine_core_inst_Cpu64 BaselineVersion=10.3.5500.0; PatchFileName=sql_engine_core_inst.msp PatchCode={9145CF54-462E-4A28-8FB5-A44C93AD3716}
2014-11-18 19:16:30 Slp: Patch Id: KB2977321_sql_engine_core_inst_Cpu32 - The baseline msi is not installed.
The patch package is ignored.
2014-11-18 19:16:30 Slp: Patch Id: KB2977321_sql_engine_core_inst_Cpu32 - Detail description of this patch package is: PatchId=KB2977321_sql_engine_core_inst_Cpu32 PatchVersion=10.3.5520.0 BaselinePackageId=sql_engine_core_inst_Cpu32
BaselineVersion=10.3.5500.0; PatchFileName=sql_engine_core_inst.msp PatchCode={9145CF54-462E-4A28-8FB5-A44C93AD3716}
2014-11-18 19:16:30 Slp: Baseline Package Id sql_rs_Cpu64 - The highest patch version is 10.3.5500.0
2014-11-18 19:16:30 Slp: Patch Id KB2977321_sql_rs_Cpu64 - NotInstalled on the baseline msi package sql_rs_Cpu64.
Detail description of this patch package is: PatchId=KB2977321_sql_rs_Cpu64 PatchVersion=10.3.5520.0 BaselinePackageId=sql_rs_Cpu64 BaselineVersion=10.3.5500.0; PatchFileName=sql_rs.msp PatchCode={2296F7DD-2D3D-4802-B61A-AE7460EFB767}
2014-11-18 19:16:30 Slp: Patch Id: KB2977321_sql_rs_Cpu32 - The baseline msi is not installed.
The patch package is ignored.
2014-11-18 19:16:30 Slp: Patch Id: KB2977321_sql_rs_Cpu32 - Detail description of this patch package is: PatchId=KB2977321_sql_rs_Cpu32 PatchVersion=10.3.5520.0 BaselinePackageId=sql_rs_Cpu32 BaselineVersion=10.3.5500.0;
PatchFileName=sql_rs.msp PatchCode={2296F7DD-2D3D-4802-B61A-AE7460EFB767}
2014-11-18 19:16:30 Slp: Baseline Package Id sql_is_Cpu64 - The highest patch version is 10.3.5500.0
2014-11-18 19:16:30 Slp: Patch Id KB2977321_sql_is_Cpu64 - NotInstalled on the baseline msi package sql_is_Cpu64.
Detail description of this patch package is: PatchId=KB2977321_sql_is_Cpu64 PatchVersion=10.3.5520.0 BaselinePackageId=sql_is_Cpu64 BaselineVersion=10.3.5500.0; PatchFileName=sql_is.msp PatchCode={E870296C-24CC-4D82-BB59-CD136692E2BD}
2014-11-18 19:16:30 Slp: Baseline Package Id sql_bids_Cpu64 - The highest patch version is 10.3.5500.0
2014-11-18 19:16:30 Slp: Patch Id KB2977321_sql_bids_Cpu64 - NotInstalled on the baseline msi package sql_bids_Cpu64.
Detail description of this patch package is: PatchId=KB2977321_sql_bids_Cpu64 PatchVersion=10.3.5520.0 BaselinePackageId=sql_bids_Cpu64 BaselineVersion=10.3.5500.0; PatchFileName=sql_bids.msp PatchCode={EA407FA6-C2D1-4D3D-9227-B9E06DDDEFD0}
2014-11-18 19:16:30 Slp: Baseline Package Id sql_ssms_Cpu64 - The highest patch version is 10.3.5500.0
2014-11-18 19:16:30 Slp: Patch Id KB2977321_sql_ssms_Cpu64 - NotInstalled on the baseline msi package sql_ssms_Cpu64.
Detail description of this patch package is: PatchId=KB2977321_sql_ssms_Cpu64 PatchVersion=10.3.5520.0 BaselinePackageId=sql_ssms_Cpu64 BaselineVersion=10.3.5500.0; PatchFileName=sql_ssms.msp PatchCode={8A81B870-E8F0-415D-AC80-13BEAA3EC8C8}
2014-11-18 19:16:30 Slp: Baseline Package Id: sql_common_core_Cpu64 - No patches are found by SQL Discovery on the installed package whose ProductCode is {5340A3B5-3853-4745-BED2-DD9FF5371331}
2014-11-18 19:16:30 Slp: Patch Id KB2977321_sql_common_core_Cpu64 - NotInstalled on the baseline msi package sql_common_core_Cpu64.
Detail description of this patch package is: PatchId=KB2977321_sql_common_core_Cpu64 PatchVersion=10.3.5520.0 BaselinePackageId=sql_common_core_Cpu64 BaselineVersion=10.3.5500.0; PatchFileName=sql_common_core.msp PatchCode={CF023E0F-3A19-4DBF-BCA3-0F664B447EDB}
The instance came up successfully and seems to be operating normally. Was there an error or was the KB installed correctly as the result of the windows update process indicated?
Is there a way I can verify this?I did some research on this particular KB article and it seems to be related to Master Data Services which I am not using. The KB was pushed automatically and I am not sure that it was a required update in our situation. I'd like to understand exactly
what caused the error message before initiating a repair as this is a production and not a test environment. Everything appears to be functioning properly and I have received direction from Microsoft in the past that information in some logs identified
as level 'error' are in fact to be ignored. I checked the windows update and this KB shows 'Successful' rather than failed or cancelled.
I would also like more information on why sql server services should not be stopped prior to allowing the OS patches to be applied. I have received messages in the past that stopping the services before service packs are applied
prevent the necessity for a reboot of the machine. I've never heard before that it is a best practice not to stop Sql service prior to applying patches. Once the services are stopped, I have our infrastructure admin start a VM snapshot on
the machine then kick off the windows update process. When done, I reboot the machine, test out Sql Server processes and then if all goes well give the ok to release the VM snapshot. I've supported various databases for 12 years, Sql Server for 5
years and this is the first time I've heard stopping the service manually can cause problems. If that is the case, I will certainly change how I do things....
I did run the discovery report and the results follow:
Microsoft SQL Server 2008 Setup Discovery Report
Product
Instance
Instance ID
Feature
Language
Edition
Version
Clustered
Sql Server 2008
MSSQLSERVER
MSSQL10.MSSQLSERVER
Database Engine Services
1033
Standard Edition
10.3.5520.0
No
Sql Server 2008
MSSQLSERVER
MSSQL10.MSSQLSERVER
SQL Server Replication
1033
Standard Edition
10.3.5520.0
No
Sql Server 2008
MSSQLSERVER
MSSQL10.MSSQLSERVER
Full-Text Search
1033
Standard Edition
10.3.5500.0
No
Sql Server 2008
MSSQLSERVER
MSAS10.MSSQLSERVER
Analysis Services
1033
Standard Edition
10.3.5500.0
No
Sql Server 2008
MSSQLSERVER
MSRS10.MSSQLSERVER
Reporting Services
1033
Standard Edition
10.3.5520.0
No
Sql Server 2008
EVAULT
MSSQL10.EVAULT
Database Engine Services
1033
Standard Edition
10.3.5520.0
No
Sql Server 2008
Management Tools - Basic
1033
Standard Edition
10.3.5520.0
No
Sql Server 2008
Management Tools - Complete
1033
Standard Edition
10.3.5500.0
No
Sql Server 2008
Client Tools Connectivity
1033
Standard Edition
10.3.5500.0
No
Sql Server 2008
Client Tools Backwards Compatibility
1033
Standard Edition
10.3.5500.0
No
Sql Server 2008
Client Tools SDK
1033
Standard Edition
10.3.5500.0
No
Sql Server 2008
Integration Services
1033
Standard Edition
10.3.5520.0
No -
Dreamweaver 8 bindings - to MySQL, error code 500
Hello!
Well, I've spent five days searching online forums, and a few
posts come close to my problem, but not getting any clues to a
solution. I hope one of the resident experts or members could shed
some light...
Windows XP
Dreamweaver 8.0.2 (just upgraded - same problem)
- Used setup-v1.17-apache-2.2.2-win32.exe for setup - from
devside.net PHP 5.2.0-dev MySQL 4.1.7 (installed new after package.
Have two instances of mysql on my system - one active, one in
manual-inactive)
- All was going well until trying to establish bindings in
Dreamweaver. PHP is up and running. MySQL loaded, and database
connection fine. Bindings gets the error... "HTTP Error Code 500
Internal Server Error"
Just getting back to it... Again, thank you for your help!
Dreamweaver 8 has support for PHP 5. Version I'm using is
5.2.0. MX specifies versions 4.x and above are required. I'll have
to research if the support cuts off at 5.0.
My Connections file: conn_newland.php (I'm following the book
tutorial):
<?php
# FileName="Connection_php_mysql.htm"
# Type="MYSQL"
# HTTP="true"
$hostname_conn_newland = "localhost";
$database_conn_newland = "newland_tours";
$username_conn_newland = "root";
$password_conn_newland = "";
$conn_newland = mysql_pconnect($hostname_conn_newland,
$username_conn_newland, $password_conn_newland) or
die(mysql_error());
$Recordset1 = mysql_query("SHOW variables", $Connection1);
echo "<table border=1 width=100%>";
while ($row_Recordset1 = mysql_fetch_assoc($Recordset1)) {
echo
"<tr><td>".$row_Recordset1['Variable_name']."</td><td>".$row_Recordset1['Value']."</td></ tr>";
echo "</table>";
?>
Recordset parameters I entered in bindings:
Name: rs_journal
Connection: conn_newland
Table: tbl_journal
Columns: Selected - journalID, journal_entry
Filter: none
Sort: journalID Descending
Clicking Test gives: "HTTP Error Code 500 Internal Server
Error"
By the way, the reason I didn't specify a password in "root'
is that I had a problem before that I didn't know enough to
overcome, so had to reinstall MySQL. However, the same error occurs
if I specify another user name and password (previously set up).
7:30 pm -
Adding to this post...
I found the following at
http://www.adobe.com/cfusion/knowledgebase/index.cfm?id=tn_16515.
However, it appears it may be referring only to Dreamweaver MX 2004
on Mac OS X. I have Dreamweaver 8 on Windows XP:
Verify that the connection scripts are up on the server
This section is related to the section above. In a web
browser, browse to the URL prefix you have defined in the Testing
Server category of the site definition and add
/_mmServerScripts/MMHTTPDB.php. For example:
http:/myserver/mysite/_mmServerScripts/MMHTTPDB.php. If things are
working correctly, you should see something like the following text
returned in the web browser:
Notice: Undefined index: Type in
c:\inetpub\wwwroot\mysite\_mmServerScripts\MMHTTPDB.php on line 13
Notice: Undefined variable: oConn in
c:\inetpub\wwwroot\mysite\_mmServerScripts\MMHTTPDB.php on line 20
When I go to the file above, this is the message I receive
(only thing that appears):
The files from the _mmServerScripts folder are for the server
model PHP-MySQL. You try to connect to a database using a different
server model . Please remove this folder outside the Dreamweaver
environment on both local and testing machines and try again.\n
Is there a hint here of what the problem is? I need some help
in possible interpretations.
Previous attempts made to solve:
- re-installed MySQL with mysql-5.0.24-win32.zip in
recommended directory (outside the www directory). I now have two
instances of MySQL on my local server - one set to automatic
loading and the other manual (switched off)
- one post suggested problem might be with ODBC - installed
SQL ODBC with mysql-connector-odbc-3.51.12-win32.msi. However, I
don't have a clue as to whether it's connected to anything...
- successfully connected to SQL database through root without
password and specific logon and password. No difference.
- other posts suggest problem could reside in php.ini,
htaccess, my.ini (SQL). I know where to find them, but don't have
an understanding of what parameters to shift, if any. One post
suggested a port problem, and I did see a port problem, presently
set to 3306.
From what I've been able to gather, this has been recognized
as an issue before, but there doesn't seem to be any documentation
online (or at least what I've been able to find) dealing with this.
And any mention of the problem that I've seen references
Dreamweaver MX, not 8, although I don't think the version
difference is a significant issue.
This error must be relatively rare, or I'd see more out there
about it. Still, I hope that at least one of the community experts
may have come across it.
Will be waiting with bated breath -- at least for a few
days...
Thanks!
JoeHello,
I have also had the same error - namely that whilst I could connect via ftp, upload/download files, and view database tables, any attempt to view of modify recordsets resulted in error 500.
Having checked other potential causes (e.g. selection/non-selection use of passive FTP setting, enabling of php, etc.), on the back of posts here I contacted my host and asked if if could relate to mod security, as further investigation revealed that the issue only occurred on sites where mod security had not been disabled (I don't like to disable mod security for obvious reasons - and I'm told you can't do that site by site with apache2 anyway).
After a few false starts, the problem was resolved - with the following response from my host: "The false positives were being generated by "/_mmServerScripts/MMHTTPDB.php" and that is what we've worked around in the rules. As such, any domain on [servername] using that script in the same way shouldn't generate a false-positive moving forward."
So it seems the answer (assuming your on an apache server of course) may be to modify the rules to allow full access for MMHTTPDB.php.
I hope that is of help to some. -
Error Code 21, iphone 4S stuck in DFU mode and will not restore!
Hi All,
My brand new Iphone 4S will not switch on unless it is connected to the charger/usb connection to the laptop, before we go any further the battery is fully charged. When you connect the phone to the charger plug you can go through the set up routine until a point is reached when it displays "conect to itunes" however, as soon as you disconect the usb cable from the charger plug to conect it to the laptop it appears to just switch off and then display the apple logo, the screen then goes blank and then the logo again, it carries on doing this indefinately.
I can get the phone into DFU mode and itunes will recognise it, IOS 5.0.1 downloads and it attempts to restore the phone but I then get an "unknown error message (21)" I just cant get past this point, I have also tried the restore procedure on a friends Windows laptop and a MacBook Pro but still no joy.
I have booked an appointment at my nearest Genius Bar (which is miles away) on Thursday but I could well do without having to make this trip, can anyone please advise me if there is something else to try?
Thanks in advance.Thanks for the reply, yes I did disable my firewall and antivirus software staight after my first failed restore attempt but it made no difference, like you I also checked out the error code explination.
What I cant understand is why dosent this phone does not work straight out of the box?...its brand new, I have not tried to jailbreak it, (I have recently seen this as a possible cause in another post) I just want the bloody thing to work!
I also forgot to mention in my post that the phone will not respond to any key presses or show any signs of life unless it is conected to a power source and beleive me it has spent most of the last 2 days conected to one due to this, the battery indicator shows it is fully charged.
Any more help is very much appreciated.
Maybe you are looking for
-
Dynamic displaying of decimal points for currency field in ALV
Hi, In ALV output there is a currency field and displaying data of different countries. It should display decimal point according to the country's currency. But at a time it can display data of different countries.
-
How to invoke a Pop up window on screens.
-
Search help-vendor master combine classification with additional criteria
I want to build a single search help with classification data and vendor master data. I have a classification on the vendor master identifying the state the vendor is licensed to do business in. I also have the city from the vendor address. I have
-
Remove Focus from Main Frame after Jinternal Frame is opened.
Hi, I want to restrict the user to change any thing on main frame once the JInternalFrame is opened (you can see same effect when we execute JOptionPane where focus on main is not retain untill you close the JOptionPane). I have written following cod
-
Computer locks up, so I want to reinstall the OS. I had upgraded to Snow Leopard. Tried to do an archive and install from the DVD that came with the computer, but that failed. Tried to do an erase and install, but the install stops somewhere near t