Unequal Load Balancing with EIGRP over 4 Wireless networks

We are trying to load-balance on 4 interfaces that have unequal bandwidths. The setup looks like this
8 Computers -> Empty Config Switch -> 3560 Router\Switch -> 4x Wireless Radios on different frequencies - networks -> 3560 Router\Switch->Empty Config Switch -> 8 Computers
We have EIGRP setup and the bandwidths defined, and the routes are showing proper share counts, but once we start adding traffic to the network, they all jump on one of the links. The config and everything looks right, its just not working. I have tried switching to different cef algorithms. Removed the vlans . I made them equal cost and they did the same thing. Its like EIGRP does not want to load balance.
When i did this config with static routes or as OSPF, it actually load balanced them, but I'm stuck with a 1:1 share ratio. If i could control the ratio, then that would be an acceptable solution.
Any ideas on what could be causing this?
Code:
Routing entry for 192.168.104.0/24
Known via "eigrp 10", distance 90, metric 13312, type internal
Redistributing via eigrp 10
Last update from 192.168.2.4 on Vlan2, 00:04:25 ago
Routing Descriptor Blocks:
* 192.168.9.4, from 192.168.9.4, 00:04:25 ago, via Vlan9
      Route metric is 51712, traffic share count is 31
      Total delay is 20 microseconds, minimum bandwidth is 50000 Kbit
      Reliability 255/255, minimum MTU 1500 bytes
      Loading 1/255, Hops 1
    192.168.5.4, from 192.168.5.4, 00:04:25 ago, via Vlan5
      Route metric is 13312, traffic share count is 120
      Total delay is 20 microseconds, minimum bandwidth is 200000 Kbit
      Reliability 255/255, minimum MTU 1500 bytes
      Loading 1/255, Hops 1
    192.168.3.4, from 192.168.3.4, 00:04:25 ago, via Vlan3
      Route metric is 26112, traffic share count is 61
      Total delay is 20 microseconds, minimum bandwidth is 100000 Kbit
      Reliability 255/255, minimum MTU 1500 bytes
      Loading 1/255, Hops 1
    192.168.2.4, from 192.168.2.4, 00:04:25 ago, via Vlan2
      Route metric is 13312, traffic share count is 120
      Total delay is 20 microseconds, minimum bandwidth is 200000 Kbit
      Reliability 255/255, minimum MTU 1500 bytes
      Loading 1/255, Hops 1
3560_Switch_1#show int Fa 0/1 | inc packets/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
3560_Switch_1#show int Fa 0/2 | inc packets/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
3560_Switch_1#show int Fa 0/3 | inc packets/sec
5 minute input rate 17111000 bits/sec, 2545 packets/sec
5 minute output rate 13872000 bits/sec, 2251 packets/sec
3560_Switch_1#show int Fa 0/4 | inc packets/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
3560_Switch_1#show ip cef exact-route 192.168.101.57 192.168.104.57
192.168.101.57 -> 192.168.104.57 => IP adj out of Vlan5, addr 192.168.5.4
Here is the config.
Code:
ip cef load-sharing algorithm universal 00123456
interface FastEthernet0/1
switchport access vlan 2
bandwidth 200000
delay 1
spanning-tree portfast
interface FastEthernet0/2
switchport access vlan 3
bandwidth 200000
delay 1
spanning-tree portfast
interface FastEthernet0/3
switchport access vlan 5
bandwidth 200000
delay 1
spanning-tree portfast
interface FastEthernet0/4
switchport access vlan 9
bandwidth 200000
delay 1
spanning-tree portfast
interface GigabitEthernet0/1
description USER PORT
switchport access vlan 100
spanning-tree portfast
interface Vlan2
bandwidth 200000
ip address 192.168.2.1 255.255.255.0
delay 1
interface Vlan3
bandwidth 100000
ip address 192.168.3.1 255.255.255.0
delay 1
interface Vlan5
bandwidth 200000
ip address 192.168.5.1 255.255.255.0
delay 1
interface Vlan9
bandwidth 50000
ip address 192.168.9.1 255.255.255.0
delay 1
interface Vlan100
description User Data
ip address 192.168.101.1 255.255.255.0
router eigrp 10
maximum-paths 8
variance 15
network 192.168.2.0
network 192.168.3.0
network 192.168.5.0
network 192.168.9.0
network 192.168.101.0

Yup, that was the first cef algorithm I had tried. ip cef load-sharing algorithm include-ports source destination
I tried all of the different types.
Also, I was sending data trough iperf from 4 computers + 1 comp steaming video on one network to 5 computers on another network. In any case of source or destination, it should have switched over. The odds of it all going on Vlan 5 is ~ 0.6% Restarting the router sometimes places it all on a different vlan, but in any case its all or nothing.

Similar Messages

Load balancing with eigrp

does eigrp load balance automatically, say I had 2 serials to one place, would it automatically load balance, how would I turn it off say on one link ?

hi
AFAIK all the routing protocol does supports equal cost path load balancing.
if u dont want to have this behaviour i would suggest to try changing the delay on the interface (on which you dont want to pass the traffic in nomral conditions)which will change the cost and will turn off the loadbalancing on both the links..
regds

Load balancing with use of router 881.

Hello,
I have two MPLS line and i want load balancing with the help of CISCO router 881. is it necessary that i require two router on both location.? if one location have firewall and one location have cisco router 881 then can i do a load balancing or i require two router each on both location ? What are the basic requirement that i need.
Thanks,
Kuntal

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
An 881 should be able to load share across multiple ports. Many routing protocol support ECMP, including BGP, but you need "special" hidden/secret commands to enable. EIGRP also supports unequal cost load sharing.
If an 881 supports OER or PfR, those too will do unequal load sharing, dynamically.

CF 10 Load-Balancing with Remote Instances

I was reading an article on Clustering/LB/HA using CF8, but have not found any updates for CF10.
Using VM VirtualBox to setup a few virtual servers, I am looking to setup a load balancing of ColdFusion 10 on 2 remote instances. The goal would be have ColdFusion Cluster Manager be able to point http request to one of the two servers based on load/availability. Not really having a hardware cluster/failover setup, just managing resources on two CF instances instead of a standalone.
The servers are Windows Server 2008 R2 with IIS7.5 and ColdFusion 10 Enterprise on installed on 3 of these machines. Let's call them CF-LBManager, CF-Web1, and CF-Web 2. In the CF Docs, they show the Cluster Manager adding the local CF instance and "if you want" a remote instance. However, this scenario would require the main instance to be running and not fail for it to direct to the other instance.
I am trying to set this up now with CF-LBManager as just a manager of the requests coming in. In the Enterprise Manager >> Instance Manager, the local instance is shown and I add the two remote instances with the correct Remote Port, JVM Route, etc. I also made sure the <Cluster>...</Cluster> block was added to the two remote instances (CF-Web1 and CF-Web2) \runtime\conf\server.xml file too, Jetty Services also is running. Now under the Enterprise Manager >> Cluster Manager I add the two remote instances to the cluster, not the local instance on CF-LBManager with Multicast Port and Sticky Sessions enabled. On Submit, I get a green message "You must restart all the server instances and any configured webservers for these changes to take effect.". I go ahead and reboot the servers and come back.
I now browse to the ColdFusion page as a test on CF-Web1 and CF-Web2 to make sure CF is running properly, they do. I then browse the IP of the CF-LBManager, however it only returns the local IIS web site and not redirect to one of the two cluster members. I am not seeing any message on the coldfusion-out.log on the remote instances. Am I not setting this up correctly or not enabling the Cluster Manager to take over and pass along the requests to those in the cluster?

Unfortunatley I don't have a lot of experience with CF10 on Windows, but if you are running CF behind IIS I think you will need to update the Tomcat connector configuraiton to do load balancing. I'm not sure if re-running the wsconfig tool on all of the servers will do this or not, but that is what I would suggest trying first. If that doesn't work you will need to update the Tomcat connector configuraiton manually. You can find more information on load balancing with the Tomcat connector here: http://tomcat.apache.org/connectors-doc/generic_howto/loadbalancers.html.

How does load-balancing with WebCache work - is there still a bottleneck?

Hello,
We're migrating an old Forms 6i app to 10.1.2.0.2 (apps servers = Redhat Linux), and are starting to consider using WebCache to loadbalance between two application servers.
My question is this - say we have apps servers A and B, both running Forms and Reports Services. We use Webcache on server A (don't have the luxury of a third apps server...) to load balance between A and B. So all initial requests come into A, which in some cases may then be diverted to start a new Forms session on B.
For those users whose middle-tier sessions are now running on B - will all network traffic for their Forms session continue to be routed through Webcache on A, then to B, over the course of the session? Or does Webcache somehow shunt the whole connection to be straight between the client PC and server B, for the duration of that Forms session?
If the former, does that mean that the server hosting Webcache can still be a significant bottleneck for network traffic? Have people found load-balancing with Webcache to be useful..?
Thanks in advance,
James

Hi gudnyc,
Thanks for posting on Adobe forums.
For HDPI you do not have to do any It will adjust automatically.
http://helpx.adobe.com/photoshop-elements/using/whats-new.html
Regards,
Sandeep

Load-balancing and fail-over between web containers and EJB containers

When web components and EJB components are run in different OC4J instances, can we achieve load-balancing and fail-over between web containers and EJB containers?
null

It looks like there is clustering, but not loadbalancing available for rmi
from the rmi.xml configuration. The application will treat any ejbs on the
cluster as one-to-one look-ups. Orion will go out and get the first ejb
available on the cluster. See the docs on configuring rmi.xml (and also the
note below).
That is a kind-of failover, because if machine A goes down, and the
myotherAejbs.jar are on machine B too, orion will go out and get the bean
from machine B when it can't find machine A. But it doesn't go machine A
then machine B for each remote instance of the bean. You could also specify
the maximum number of instances of a bean, and as one machine gets "loaded",
orion would go to the next available machine...but that's not really
loadbalancing.
That is, you can set up your web-apps with ejbs, but let all of the ejbs be
remote="true" in the orion-application.xml file:
<?xml version="1.0"?>
<!DOCTYPE orion-application PUBLIC "-//Evermind//DTD J2EE Application
runtime 1.2//EN" "http://www.orionserver.com/dtds/orion-application.dtd">
<orion-application deployment-version="1.5.2">
<ejb-module remote="true" path="myotherAejbs.jar" />
<ejb-module remote="true" path="myotherBejbs.jar" />
<ejb-module remote="true" path="myotherCejbs.jar" />
&ltweb-module id="mysite" path="mysite.war" />
... other stuff ...
</orion-application>In the rmi.xml you would define your clustering:
<cluster host="230.0.0.1" id="123" password="123abc" port="9127"
username="cluster-user" />
Tag that is defined if the application is to be clustered. Used to set up
a local multicast cluster. A username and password used for the servers to
intercommunicate also needs to be specified.
host - The multicast host/ip to transmit and receive cluster data on. The
default is 230.0.0.1.
id - The id (number) of this cluster node to identify itself with in the
cluster. The default is based on local machine IP.
password - The password configured for cluster access. Needs to match that
of the other nodes in the cluster.
port - The port to transmit and receive cluster data on. The default is
9127.
username - The username configured for cluster access. Needs to match that
of the other nodes in the cluster.

Unequal Load Balance on Etherchannel (L2/SW3400ME)

Hi, i have a problem with my L2 port-channel between 2 SW ME-3400-24TS-D (12.2(44)SE5), there is a unequal load balance and i don't know how to fixed. Should I change the load balance method?.
All four ports have the same config, except one (int fa0/1 on SW_2) that have this commands:
MAMANIVLN1P1IRA1#SH RUN INT FA0/1 | INC hold
hold-queue 4096 in
hold-queue 4096 out
Should i change this hold-queue config?
Here more outputs where you can see the diference, one link has 2mb and the other link has 60mb,, that's a big diference, i would like to know how to solve this:
SW_1#sh int fa0/9 | inc (Desc|rate)
Description: !!!!!! HACIA SW_2 !!!!!
Queueing strategy: fifo
5 minute input rate 2088000 bits/sec, 2065 packets/sec
5 minute output rate 25000 bits/sec, 46 packets/sec
SW_1#sh int fa0/10 | inc (Desc|rate)
Description: PORTCHANNEL10 HACIA SW_2
Queueing strategy: fifo
5 minute input rate 1905000 bits/sec, 1948 packets/sec
5 minute output rate 63348000 bits/sec, 6095 packets/sec
SW_2#sh int fa0/1 | inc (Desc|rate)
Description: Hacia SW_1_Fa0/9
Queueing strategy: fifo
30 second input rate 27000 bits/sec, 48 packets/sec
30 second output rate 2385000 bits/sec, 1996 packets/sec
SW_2#sh int fa0/2 | inc (Desc|rate)
Description: PORTCHANNEL10 HACIA SW_1
Queueing strategy: fifo
5 minute input rate 63567000 bits/sec, 6114 packets/sec
5 minute output rate 1935000 bits/sec, 1976 packets/sec
more outputs...
SW_1#sh etherchannel load-balance
EtherChannel Load-Balancing Configuration:
src-mac
EtherChannel Load-Balancing Addresses Used Per-Protocol:
Non-IP: Source MAC address
IPv4: Source MAC address
SW_2#sh etherchannel load-balance
EtherChannel Load-Balancing Configuration:
src-mac
EtherChannel Load-Balancing Addresses Used Per-Protocol:
Non-IP: Source MAC address
IPv4: Source MAC address
SW_1#SH MAC ADDress-table INTerface po10 | inc Total
Total Mac Addresses for this criterion: 297
SW_2#SH MAC ADDress-table INTerface po10 | inc Total
Total Mac Addresses for this criterion: 66
In advance thanks for the help.

Normally it will fairly well balance the traffic . There is no way to make sure each channel is exactly the same utilization wise . You can look at how it is load balanced and make a change from say mac to ip address if it looks like you aren't getting the balance you want . It would be very rare that you are going to fill one port on the channel without filling the rest almost the same .Exceptions would be if you most of your traffic is headed to one place like a certain server , even then if you used ip addresses in both directions as the load balance I think it would balance out pretty good. If it got to that point where one link was almost filled you would have to think about adding another port to the channel . This is a real good page http://www.cisco.com/en/US/tech/tk389/tk213/technologies_tech_note09186a0080094714.shtml

CSS Load Balancing with Cookies

We are trying to load balance 2 backend servers hosted on Websphere with advance balance cookies method.
Restrictions
ServerA is unable to accept cookies generated from ServerB.
ServerA and ServerB are generating random cookies
Unable to modify cookie string with a constant.
How can we load balance based on cookies considering the above restrictions?
We have attempted to do hash based load balancing with cookies but the problem we run into is the servers do not accept cookies generated from another server.
The configuration we tried is written below:
service ServerA
ip address 192.168.10.2
keepalive type tcp
keepalive port 80
active
service ServerB
ip address 192.168.20.2
keepalive type tcp
keepalive port 80
active
content ABC
url "/*"
add service ServerA
string prefix "JSESSIONID="
advanced-balance cookies
port 80
add service ServerB
string skip-length 5
string process-length 16
string operation hash-xor
protocol tcp
vip address 172.16.32.1
active
Can we change the string prefix to JSESSION instead of JSESSIONID= ?
The only place the app guys can add a constant string to match on is before the = sign.
Is it possible for CSS to match on a constant string before = sign e.g below:
service ServerA
ip address 192.168.10.2
keepalive type tcp
keepalive port 80
string id567=
active
service ServerB
ip address 192.168.20.2
keepalive type tcp
keepalive port 80
string id123=
active
content ABC
url "/*"
add service ServerA
string prefix "JSESSION"
advanced-balance cookies
port 80
add service ServerB
string skip-length 0
string process-length 6
protocol tcp
vip address 172.16.32.1
active

It should work.
There is no reason for it not to work...
This is the best method you can have on the CSS for stickyness.
Get a sniffer trace on the client and server with arrowpoint cookie configured on the CSS and capture a failure so we can see what is going on.
also send me the config so I can verify everything is ok.
If you have a service request open with the TAC, you can also give the SR # so I can review what has been done.
Gilles.

Cache and Load Balancing with Oracle APEX Listener

Hi,
I intend to use only HTTP access.
How to implement a Cache and Load Balancing with the Oracle APEX Listener?
Is it possible to do with the the standalone running APEX Listener?
Thanks by advance for any tips/documentation/references.
Kind Regards.

Hi,
I think this question is best asked in the APEX Listener forum:
ORDS, SODA & JSON in the Database
Kind regards
Sandro

Load balancing with JSP

Anyone and everyone,
When configuring load balancing with Weblogic clusters, does load
balancing take effect for all services or just EJB and RMI? Or another
way of saying the same thing, can I setup weighted load balancing for
the JSP engines across 2 weblogic servers.
Thanks in advance,
Mike

The load-balancing documentation you read describing the different algorithms only applies to RMI stubs (e.g., EJB clients). Please see http://www.weblogic.com/docs51/cluster/concepts.html#1026091 for a description of how load-balancing/clustering works with servlets/JSPs.
The short answer is that in using servlet clustering, most people want/need/use in-memory replication for HttpSession objects. In WLS 5.1 (and before), in-memory replication requires one or more proxy servers be set-up in front of the cluster. Typically, most people use something like BigIP to load-balance
across the proxy servers and let the weblogic plug-in for the proxy server handle the routing to the cluster. The plug-in uses round-robin until an HttpSession is established for a user, then it always tries to route to the server where the user's session is located.
Hope this helps,
Robert
Brian Lin wrote:
All,
I have a quesiton here regarding load balancing with DNS round robin. As of Chapter Adminstration of Clustering Weblogic server, Weblogic can be configured to balance by weight. How about Weblogic handle weight based balancing after DNS round robin ip response? or just can choose one way instead of both?
What's the big difference between choosing BigIP and software balancing (WL)?
Brian
"Wei Guan" <[email protected]> wrote:
I don't think you can configure this load balancing in weblogic in current
release. However, if you have Big-IP or LocalDireoctr, you can set up
weighted load-balancing there. Otherwise, weblogic proxy will use DNS round
robin to do the load-balancing between JSP engins.
My 2 cents.
Cheers - Wei
Michael Yakimisky <[email protected]> wrote in message
news:[email protected]...
Anyone and everyone,
When configuring load balancing with Weblogic clusters, does load
balancing take effect for all services or just EJB and RMI? Or another
way of saying the same thing, can I setup weighted load balancing for
the JSP engines across 2 weblogic servers.
Thanks in advance,
Mike

Multihomed eBGP load balancing with 3 ISP's

We currently peer with 2 ISPs using BGP in an active/failover configuration. My company wants to move to a 3 ISP model where Internet traffic is split across the 3 providers so that bandwidth is equally distributed on outgoing traffic across our 2 /22 ARIN IP ranges. This is from our 2 edge switches that have VSS.
Within my limited knowledge of BGP, I have determined that we could do load sharing pretty easily by adding multiple default routes and breaking up our /22's into /24 and advertising them that way. However, I don't think this satisfies the request that downtime must be seamless, should one link drop.
Currently, our ISP's advertise default routes. From the research that I've done, we could get close to load balanced links if we receive full BGP routes and community settings and definitions. I'm nervous about this because it looks really complicated, and I don't want our AS to turn into a transit AS. I've been told the same can be accomplished with only partial BGP routes and community settings and definitions.
Personally, I think we just need a WAN load balancer. However, given the request, is there a thread out there that can explain this, or can someone discuss this requested scenario a little bit?
Thanks!

Hi there
First question would be what is the required reconvergence time for the applications using the Internet? Should an outage occur, when do they lose their state? Once you know that, you then have a target to aim for in terms of recovery
With regards load-balancing, with BGP we are always talking inbound and outbound.
The outbound solution is relatively simple - each ISP advertises a default route to your Internet edge router(s). Create an eBGP session from each edge router to the core, advertise the default route and redistribute into the IGP. Ensure the IGP cost to each BGP next hop is equal and you have ECMP for outbound routing.
Inbound influence is usually via MED (not likely in this case given 3 ISPs), adjusting local-pref in the ISP via BGP EXT communities configured your end, or via AS-PATH prepending for longer prefixes from your /22. Prepending would be simplest, but your unlikely to get an exact inbound traffic split, however a relatively even distribution should be sufficient.

Load Balancing with BigIP / SSL question

I have an oddball question. We're load balancing ColdFusion
MX7 across 3 servers using a BigIP load balancing server. We
decided to go the hardware approach and it has been great except
for one small configuration issue.
We use a mix of SSL and non SSL pages, prior to the switch
from a single server to a load balanced setup I used to script that
would determine if a page that was supposed to be SSL had the
variable CGI.HTTPS turned on or off. If it was off, the page would
redirect back to itself with the SSL turned on.
The problem we have is that we followed BigIP's instruction
to secure the load balancing hardware instead of the three servers
running behind it. So what happens is that the traffic goes to the
load balancer port 441, but then the calls from the load balancer
to the individual servers is port 80. So even if a page is called
as HTTPS://... the coldfusion server says that CGI.HTTPS is "off"
since the traffic is port 80.
This isn't much of a problem, our SSL pages are linked as
HTTPS:// and the only problem would actually arise if someone was
to type in the URL and call it as HTTP rather than HTTPS.
My questions is this, does anyone know of a way that I can
detect if the page should be HTTPS and is not without changing our
configuration and putting SSL certificates on each individual
server?

Hey,
Well the load balancing with the BigIP device is really very
amazing. I think
what i liked most was swapping out servers when their lease
was up, through the
BigIP manager I just stopped all traffic to a server, shut it
down, plugged in
the new one and turned traffic back on. It was really very
easy.
The SSL stuff still gives me a headache to think about. but
I should mention I
no longer work where I was, plus now I'm all .net C# but
that's a different
story.
I think if I was going to do this all again I would not have
secured the bigIP
unit. It was nice to buy one SSL cert for all the servers I
attached rather
than one per server, but getting the SSL sites to work
properly was a headache.
We also use windows file replication where now I would go
with like a pair of
Dell MD1000's mirrored for storage and just have tons of ram
and cpu on the
front end units. Depends what you want to spend I guess. I
think the bigIP unit
we bought was like 20 grand, i think they are cheaper now
though.
Hope I helped.

WLS6.1sp1 stateful EJB problem = load-balancing and fail over

          I have three problem
          1. I have 2 clustered server. my weblogic-ejb-jar.xml is here
          <?xml version="1.0"?>
          <!DOCTYPE weblogic-ejb-jar PUBLIC '-//BEA Systems, Inc.//DTD WebLogic 6.0.0 EJB//EN'
          'http://www.bea.com/servers/wls600/dtd/weblogic-ejb-jar.dtd'>
          <weblogic-ejb-jar>
          <weblogic-enterprise-bean>
               <ejb-name>DBStatefulEJB</ejb-name>
               <stateful-session-descriptor>
               <stateful-session-cache>
                    <max-beans-in-cache>100</max-beans-in-cache>
                    <idle-timeout-seconds>120</idle-timeout-seconds>
               </stateful-session-cache>
               <stateful-session-clustering>
                    <home-is-clusterable>true</home-is-clusterable>
                    <home-load-algorithm>RoundRobin</home-load-algorithm>
                    <home-call-router-class-name>common.QARouter</home-call-router-class-name>
                    <replication-type>InMemory</replication-type>
               </stateful-session-clustering>
               </stateful-session-descriptor>
               <jndi-name>com.daou.EJBS.solutions.DBStatefulBean</jndi-name>
          </weblogic-enterprise-bean>
          </weblogic-ejb-jar>
          when i use "<home-call-router-class-name>common.QARouter</home-call-router-class-name>"
          and deploy this ejb, exception cause
          <Warning> <Dispatcher> <RuntimeException thrown b
          y rmi server: 'weblogic.rmi.cluster.ReplicaAwareServerRef@9 - jvmid: '2903098842
          594628659S:203.231.15.167:[5001,5001,5002,5002,5001,5002,-1]:mydomain:cluster1',
          oid: '9', implementation: 'weblogic.jndi.internal.RootNamingNode@5f39bc''
          java.lang.IllegalArgumentException: Failed to instantiate weblogic.rmi.cluster.B
          asicReplicaHandler due to java.lang.reflect.InvocationTargetException
          at weblogic.rmi.cluster.ReplicaAwareInfo.instantiate(ReplicaAwareInfo.ja
          va:185)
          at weblogic.rmi.cluster.ReplicaAwareInfo.getReplicaHandler(ReplicaAwareI
          nfo.java:105)
          at weblogic.rmi.cluster.ReplicaAwareRemoteRef.initialize(ReplicaAwareRem
          oteRef.java:79)
          at weblogic.rmi.cluster.ClusterableRemoteRef.initialize(ClusterableRemot
          eRef.java:28)
          at weblogic.rmi.cluster.ClusterableRemoteObject.initializeRef(Clusterabl
          eRemoteObject.java:255)
          at weblogic.rmi.cluster.ClusterableRemoteObject.onBind(ClusterableRemote
          Object.java:149)
          at weblogic.jndi.internal.BasicNamingNode.rebindHere(BasicNamingNode.jav
          a:392)
          at weblogic.jndi.internal.ServerNamingNode.rebindHere(ServerNamingNode.j
          ava:142)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          2)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.RootNamingNode_WLSkel.invoke(Unknown Source)
          at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:296)
          So do i must use it or not???
          2. When i don't use "<home-call-router-class-name>common.QARouter</home-call-router-class-name>"
          , there's no exception
          but load balancing does not happen. According to the document , there's must load
          balancing when i call home.create() method.
          my client program goes here
               DBStateful the_ejb1 = (DBStateful) PortableRemoteObject.narrow(home.create(),
          DBStateful.class);
               DBStateful the_ejb2 = (DBStateful) PortableRemoteObject.narrow(home.create(3),
          DBStateful.class);
          the result is like that
               the_ejb1 = ClusterableRemoteRef(203.231.15.167 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@4695a6)/397
               the_ejb2 = ClusterableRemoteRef(203.231.15.167 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@acf6e)/398
               or
               the_ejb1 = ClusterableRemoteRef(203.231.15.125 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@252fdf)/380
               the_ejb2 = ClusterableRemoteRef(203.231.15.125 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@6a0252)/381
               I think the result should be like under one... isn't it??
               the_ejb1 = ClusterableRemoteRef(203.231.15.167 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@4695a6)/397
               the_ejb2 = ClusterableRemoteRef(203.231.15.125 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@6a0252)/381
          In this case i think the_ejb1 and the_ejb2 must have instance in different cluster
          server
          but they go to one server .
          3. If i don't use      "<home-call-router-class-name>common.QARouter</home-call-router-class-name>",
          "<replication-type>InMemory</replication-type>" then load balancing happen but
          there's no fail-over
          So how can i get load-balancing and fail over together??


          I have three problem
          1. I have 2 clustered server. my weblogic-ejb-jar.xml is here
          <?xml version="1.0"?>
          <!DOCTYPE weblogic-ejb-jar PUBLIC '-//BEA Systems, Inc.//DTD WebLogic 6.0.0 EJB//EN'
          'http://www.bea.com/servers/wls600/dtd/weblogic-ejb-jar.dtd'>
          <weblogic-ejb-jar>
          <weblogic-enterprise-bean>
               <ejb-name>DBStatefulEJB</ejb-name>
               <stateful-session-descriptor>
               <stateful-session-cache>
                    <max-beans-in-cache>100</max-beans-in-cache>
                    <idle-timeout-seconds>120</idle-timeout-seconds>
               </stateful-session-cache>
               <stateful-session-clustering>
                    <home-is-clusterable>true</home-is-clusterable>
                    <home-load-algorithm>RoundRobin</home-load-algorithm>
                    <home-call-router-class-name>common.QARouter</home-call-router-class-name>
                    <replication-type>InMemory</replication-type>
               </stateful-session-clustering>
               </stateful-session-descriptor>
               <jndi-name>com.daou.EJBS.solutions.DBStatefulBean</jndi-name>
          </weblogic-enterprise-bean>
          </weblogic-ejb-jar>
          when i use "<home-call-router-class-name>common.QARouter</home-call-router-class-name>"
          and deploy this ejb, exception cause
          <Warning> <Dispatcher> <RuntimeException thrown b
          y rmi server: 'weblogic.rmi.cluster.ReplicaAwareServerRef@9 - jvmid: '2903098842
          594628659S:203.231.15.167:[5001,5001,5002,5002,5001,5002,-1]:mydomain:cluster1',
          oid: '9', implementation: 'weblogic.jndi.internal.RootNamingNode@5f39bc''
          java.lang.IllegalArgumentException: Failed to instantiate weblogic.rmi.cluster.B
          asicReplicaHandler due to java.lang.reflect.InvocationTargetException
          at weblogic.rmi.cluster.ReplicaAwareInfo.instantiate(ReplicaAwareInfo.ja
          va:185)
          at weblogic.rmi.cluster.ReplicaAwareInfo.getReplicaHandler(ReplicaAwareI
          nfo.java:105)
          at weblogic.rmi.cluster.ReplicaAwareRemoteRef.initialize(ReplicaAwareRem
          oteRef.java:79)
          at weblogic.rmi.cluster.ClusterableRemoteRef.initialize(ClusterableRemot
          eRef.java:28)
          at weblogic.rmi.cluster.ClusterableRemoteObject.initializeRef(Clusterabl
          eRemoteObject.java:255)
          at weblogic.rmi.cluster.ClusterableRemoteObject.onBind(ClusterableRemote
          Object.java:149)
          at weblogic.jndi.internal.BasicNamingNode.rebindHere(BasicNamingNode.jav
          a:392)
          at weblogic.jndi.internal.ServerNamingNode.rebindHere(ServerNamingNode.j
          ava:142)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          2)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.BasicNamingNode.rebind(BasicNamingNode.java:36
          9)
          at weblogic.jndi.internal.RootNamingNode_WLSkel.invoke(Unknown Source)
          at weblogic.rmi.internal.BasicServerRef.invoke(BasicServerRef.java:296)
          So do i must use it or not???
          2. When i don't use "<home-call-router-class-name>common.QARouter</home-call-router-class-name>"
          , there's no exception
          but load balancing does not happen. According to the document , there's must load
          balancing when i call home.create() method.
          my client program goes here
               DBStateful the_ejb1 = (DBStateful) PortableRemoteObject.narrow(home.create(),
          DBStateful.class);
               DBStateful the_ejb2 = (DBStateful) PortableRemoteObject.narrow(home.create(3),
          DBStateful.class);
          the result is like that
               the_ejb1 = ClusterableRemoteRef(203.231.15.167 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@4695a6)/397
               the_ejb2 = ClusterableRemoteRef(203.231.15.167 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@acf6e)/398
               or
               the_ejb1 = ClusterableRemoteRef(203.231.15.125 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@252fdf)/380
               the_ejb2 = ClusterableRemoteRef(203.231.15.125 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@6a0252)/381
               I think the result should be like under one... isn't it??
               the_ejb1 = ClusterableRemoteRef(203.231.15.167 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@4695a6)/397
               the_ejb2 = ClusterableRemoteRef(203.231.15.125 weblogic.rmi.cluster.PrimarySecon
               daryReplicaHandler@6a0252)/381
          In this case i think the_ejb1 and the_ejb2 must have instance in different cluster
          server
          but they go to one server .
          3. If i don't use      "<home-call-router-class-name>common.QARouter</home-call-router-class-name>",
          "<replication-type>InMemory</replication-type>" then load balancing happen but
          there's no fail-over
          So how can i get load-balancing and fail over together??

Load Balancing With Round Robin

Hi,
I have two iAS instances, each on their own box, and one iWS instance
running on a third box. I have setup the web connector to use round
robin and added the server weights. I believe that is all that is to it
to do simple load balancing with iAS. The problem is is that the
requests only go to one iAS instance. The server weights are 1 and 1.
Am I missing something here?
Thanks

Could be lots of things.
The most common misconfiguration is testing an application that is deployed "local". This application option effectively disables load balancing.
Another common mistake is to either not update the configuration of the webconnector (if the webconnector
has a seperate configuration LDAP) or to not restart
the webconnector after the configuration change.
Hope this helps. There's more things we could try, but I'll hope its one of these two easy things.

LRT224 Load Balancing with only one ISP

I found that the LRT224 Load Balancing really increased performance on my network with a single Internet Service Provider.
Also if your ISP doesn't limit the number of Public IP Addresses your ISP Device can provide to one. You can get two Public IP Address for additional port forwarding and other uses.
------------------- OR ----------------------------
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

In my case I noticed an immediate improvement in overall performance. When I do a "speedtest.net" test the speeds are always at the maximum throughput even with other heavy users on the internet. Which wasn't the case before. I suspect that the Dual WAN connections are doubling the amount of available full speed connections due to the load balancing.
It's interesting to watch the ethernet port lights on the ISP Modem blinking like mad as the LRT224 pumps data through the two ethernet ports.
Please remember to Kudo those that help you.
Linksys
Communities Technical Support

Unequal Load Balancing with EIGRP over 4 Wireless networks

Similar Messages

Maybe you are looking for