Unexpected Calls from Cisco
Hi all,
We have several customers who work off a 121 NAT configuration who are receiving missed calls from Cisco. This appears to be coming through as a telephone call and happening quite sporadically.
Any suggestions other than blocking source from the router? It is quite difficult to pin point an address as only Cisco is shown.
Thanks in advance
YT
This is a result of external sources trying to exploit possible PTSN trunks in users environments, it's being seen by a lot of people that have video or telephone systems that are accessible on the public internet. You can read a bit more about it in this discussion: sourceh323idcisco-incomingcalls. Only thing that can be done is if you're using a call control server such as VCS you can create a call policy to block the call attempts (there is one I created in the linked discussion), or if the system is stand alone as it appears you're is, block all incoming IPs traffic to the codec except those you trust to allow in. You could get the IP by going through the codec's call history, however that won't help as the source IP changes constantly.
Similar Messages
-
PRI main number visible on all the calls from Cisco Extension
My Cisco CUCM DN range is (1000 - 1099)
PRI Number is 4948 500 (500 - 599)
For incoming calls on the Cisco DN's
I have configured below
Translation Pattern ->Called Party Transformations-> Called Party Transform Mask to 10XX
So If someone calls 4948 501 it will ring on the Cisco DN 1001
4948 502 it will ring on the Cisco DN 1002
4948 503 it will ring on the Cisco DN 1003
4948 503 it will ring on the Cisco DN 1004
4948 504 it will ring on the Cisco DN 1005
But when i try to call my mobile number (9789197891) from Cisco DN 1001 it displays 4948 500
1002 it displays 4948 500 on my mobile But I want to display as 4948 502
1003 it displays 4948 500 on my mobile But I want to display as 4948 503
1004 it displays 4948 500 on my mobile But I want to display as 4948 503
1005 it displays 4948 500 on my mobile But I want to display as 4948 504
Could you someone please helphave you set the external phone number mask 4948 5XX on your DN config?
if you have already set the mask, then make sure you've checked the "Use Calling Party's External Phone Number Mask" in Route Pattern/Translation Pattern in Calling Party Transformations.
You can also run the dialed number analyzer to verify whether the transformations are applied correctly. -
Dear All,
We have two cucm Clusters in Different Locations between that clusters i created
Inter-Cluster Trunk (Non-Gatekeeper Controlled) Now all are working fine Between Clusters
audio calls & Video calls between sccp 8945 phones , but iam facing a Problem with third party
Video Phones (Polycom VVX 1500 ) Third Party SIP Phones located in second cluster, From 1 st cluster cisco 8945 Video
phone to 2nd cluster Polycom Video phone all calls are works for voice call only, but no video ,
Please Suggest me Solution.
Thank you,
SrimanTry setting up a SIP trunk between the two clusters and set a route patten just to the VVX 1500 and check how that goes.
From memory inter-cluster trunks are a H.323 like protocol which might have video inter-op issues with the Polycom device. -
Receiving Automatic calls from "CISCO" name continuously
We have installed one Cisco SX20 VC in our office last week only. Since then we are receiving auto call with name Cisco with no ip address.
Everyday approx. 250 calls we are getting on VC.
VC Network Configuration: Configured with Public static IP address, we don't have firewall in network and using as a standalone VC.
Product:
Cisco TelePresence SX20
Software version:
TC7.3.0.8cb420c
Can someone please help me to fixed this issue ASAP.
Regards,
Wajid DabirThis has been covered quite a few times already, take a look at this thread; https://supportforums.cisco.com/discussion/12340591/nuisance-h323-calls-sx20 and https://supportforums.cisco.com/discussion/12336591/sourceh323idcisco-incomingcalls and https://supportforums.cisco.com/discussion/12472426/rogue-calls-expressway-e-can-they-be-blockeddropped for starters.
Not much you can do about it unless you put your system on a private address behind a gatekeeper etc.
You can at least avoid the SIP version of these scans by at least turning off SIP listening port, or turning SIP off all together unless you really need it. But no such luck when it comes to these h.323 scans.
/jens
Please rate replies and mark question(s) as "answered" if applicable. -
Transfer VOIP Calls Between Cisco Desk Phone and Cisco Jabber For IPhone 9.5
Does anyone know how to transfer an active voip call from a Cisco IP Desk Phone to Cisco Jabber for IPhone? I can transfer a call from Cisco Jabber for IPhone to my Cisco IP Desk Phone no problem. I put the call on hold and then click "Resume" on my Cisco IP Desk Phone. However I cannot do the same but the other way around. If I put the call on hold on my Cisco IP Desk Phone, I see "no active call" on my Jabber client. The only information I could find slighlty relevant was using the Mobility Key/Remote Destination Profile feature however this defeats the object as this will forward to an external number, e.g. mobile and I just want to transfer the call within the VOIP environment between the two devices that are using the same directory number.
I am using Cisco Call Manager 9.1(2), Cisco Presence 9.1 and Cisco Jabber for IPhone 9.5.
Any help would be greatly appreciated.
Kind Regards,
Paul Parker.Did you ever find an answer to this ?
I am seeing the same behavior and trying so see if I can put calls on hold and pick them up both ways also.
The only answer I seem to have found is to use park instead
That would/should work but I would just prefer to hold/unhold
Just not sure why we would not be able to hold/unhold on what is essentially a "shared" line
Does anyone have this working for them ? -
No ringback from cisco ip phones to alcatel Phones
I have a CUCM 7.1.3 integrated with a Alcatel OXO PBX and when a try to place a call from cisco IP-Phones registered on CUCM to phones on PBX, I have no ringback,but when a place a call from cisco IP-Phones registered on CUCM to PSTN using PBX as it has a PRI line to the local PSTN, I dont have that issue.
The voice gateway connects to PBX using a PRI(E1) running MGCP and QSIG.
interface Serial 3/1:15
no ip address
encapsulation hdlc
isdn switch-type primary-qsig
isdn timer T310 120000
isdn protocol-emulate network
isdn incoming-voice voice
isdn bind-l3 ccm-manager
no cdp enableYou can configure COS values for the Cisco IP Phones so that the voice packets from Cisco IP phone are given more priority over the data packets from the PCs/Hosts. But the same might not be configurable for non Cisco IP Phone. I am not very sure of this. Other than that I guess, you can have all QoS features.
-
Need Help in expdp for resolving ORA-39127: unexpected error from call
Hi All,
My Environment is -------> Oracle 11g Database Release 1 On Windows 2003 Server SP2
Requirement is ------------> Data Pump Jobs to be completed without any error message.
I am tryring to take export data pump of a schema
Command Used --> expdp schemas=scott directory=data_pump_dir dumpfile=scorr.dmp version=11.1.0.6.0
Export Log Show this details its completed with 2 error messages
Export: Release 11.1.0.6.0 - Production on Saturday, 23 April, 2011 13:31:10
Copyright (c) 2003, 2007, Oracle. All rights reserved.
Connected to: Oracle Database 11g Enterprise Edition Release 11.1.0.6.0 - Production
With the OLAP option
FLASHBACK automatically enabled to preserve database integrity.
Starting "SYSTEM"."SYS_EXPORT_SCHEMA_01": system/******** schemas=scott directory=data_pump_dir dumpfile=scorr.dmp version=11.1.0.6.0
Estimate in progress using BLOCKS method...
Processing object type SCHEMA_EXPORT/TABLE/TABLE_DATA
Total estimation using BLOCKS method: 192 KB
Processing object type SCHEMA_EXPORT/USER
Processing object type SCHEMA_EXPORT/SYSTEM_GRANT
Processing object type SCHEMA_EXPORT/ROLE_GRANT
Processing object type SCHEMA_EXPORT/DEFAULT_ROLE
ORA-39127: unexpected error from call to export_string :=SYS.DBMS_CUBE_EXP.schema_info_exp('SCOTT',0,1,'11.01.00.06.00',newblock)
ORA-37111: Unable to load the OLAP API sharable library: (The specified module could not be found.
ORA-06512: at "SYS.DBMS_CUBE_EXP", line 205
ORA-06512: at "SYS.DBMS_CUBE_EXP", line 280
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 5980Processing object type SCHEMA_EXPORT/PRE_SCHEMA/PROCACT_SCHEMA
Processing object type SCHEMA_EXPORT/TABLE/TABLE
Processing object type SCHEMA_EXPORT/TABLE/INDEX/INDEX
Processing object type SCHEMA_EXPORT/TABLE/CONSTRAINT/CONSTRAINT
Processing object type SCHEMA_EXPORT/TABLE/INDEX/STATISTICS/INDEX_STATISTICS
Processing object type SCHEMA_EXPORT/TABLE/STATISTICS/TABLE_STATISTICS
ORA-39127: unexpected error from call to export_string :=SYS.DBMS_CUBE_EXP.schema_info_exp('SCOTT',1,1,'11.01.00.06.00',newblock)
ORA-37111: Unable to load the OLAP API sharable library: (The specified module could not be found.
ORA-06512: at "SYS.DBMS_CUBE_EXP", line 205
ORA-06512: at "SYS.DBMS_CUBE_EXP", line 280
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 5980
. . exported "SCOTT"."DEPT" 5.945 KB 4 rows
. . exported "SCOTT"."EMP" 8.585 KB 14 rows
. . exported "SCOTT"."SALGRADE" 5.875 KB 5 rows
. . exported "SCOTT"."ACCTYPE_GL_MAS" 0 KB 0 rows
. . exported "SCOTT"."BONUS" 0 KB 0 rows
Master table "SYSTEM"."SYS_EXPORT_SCHEMA_01" successfully loaded/unloaded
Dump file set for SYSTEM.SYS_EXPORT_SCHEMA_01 is:
D:\APP\ADMINISTRATOR\ADMIN\SIPDB\DPDUMP\SCORR.DMP
Job "SYSTEM"."SYS_EXPORT_SCHEMA_01" completed with 2 error(s) at 13:40:08
Please help me to resolve this issue.
Thank you,
ShanHi Shan,
I am getting very similar to yours
"ORA-37111: Unable to load the OLAP API sharable library: (The specified module could not be found."
error message while creating OLAP Analytic Workspace with AWM.
I am creating workspace for the first time, actually following some tutorial to get some knowledge about OLAP)
I see you managed to solve you problem.
I wonder how I can get this MOS DOC 852794.1 - is it possible to get it without going to Metalink?
Thanks in advance for any help.
Regards,
SC -
Hi,
I am trying to export a Schema from 11.2.0.2 and getting the below error on export
ORA-39127: unexpected error from call to export_string :=SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP(12425,1,...)
ORA-06502: PL/SQL: numeric or value error: NULL index table key value
ORA-06512: at "SYS.DBMS_RMGR_GROUP_EXPORT", line 154
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
ORA-39127: unexpected error from call to export_string :=
SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP(12424,1,...)
ORA-06502: PL/SQL: numeric or value error: NULL index table key value
ORA-06512: at "SYS.DBMS_RMGR_GROUP_EXPORT", line 154
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
ORA-39127: unexpected error from call to export_string :=SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP(12423,1,...)
ORA-06502: PL/SQL: numeric or value error: NULL index table key value
ORA-06512: at "SYS.DBMS_RMGR_GROUP_EXPORT", line 154
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
ORA-39127: unexpected error from call to export_string := SYS.DBMS_SCHED_JOB_EXPORT.GRANT_EXP(2003412,1,...)
ORA-01031: insufficient privileges
ORA-06512: at "SYS.DBMS_SCHED_MAIN_EXPORT", line 2296
ORA-06512: at "SYS.DBMS_SCHED_JOB_EXPORT", line 52
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
I have searched the forum and found similar errors, but I am struggling to understand the cause and solution.
Forums seem to indicate it may be related to bug 4358907, Re: Datapump export/import object grants given by another user but not sure it is relevant as I can see a ORA-01031: insufficient privileges in this log.
Can you please advise?
ThanksPlease show your export command and read MOS ID: ORA-39127 using datapump exp [ID 451987.1 ]
and check below forms discussion:
https://forums.oracle.com/message/10237007 -
Hi all,
I am getting this erro on a Datapump Schema export on 11.2.0.2:
ORA-39127: unexpected error from call to export_string := SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP(12425,1,...)
ORA-06502: PL/SQL: numeric or value error: NULL index table key value
ORA-06512: at "SYS.DBMS_RMGR_GROUP_EXPORT", line 154
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
ORA-39127: unexpected error from call to export_string := SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP(12424,1,...)
ORA-06502: PL/SQL: numeric or value error: NULL index table key value
ORA-06512: at "SYS.DBMS_RMGR_GROUP_EXPORT", line 154
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
ORA-39127: unexpected error from call to export_string := SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP(12423,1,...)
ORA-06502: PL/SQL: numeric or value error: NULL index table key value
ORA-06512: at "SYS.DBMS_RMGR_GROUP_EXPORT", line 154
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
ORA-39127: unexpected error from call to export_string := SYS.DBMS_SCHED_JOB_EXPORT.GRANT_EXP(2003412,1,...)
ORA-01031: insufficient privileges
ORA-06512: at "SYS.DBMS_SCHED_MAIN_EXPORT", line 2296
ORA-06512: at "SYS.DBMS_SCHED_JOB_EXPORT", line 52
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7049
I believe it requires some specific privileges on DBMS_RMGR_GROUP_EXPORT.
I have found this below explanation Kevin's Blog: SYS.DBMS_RMGR_GROUP_EXPORT.GRANT_EXP but I am not a DBA, so I am not sure what grant needs to be modified.
It also complains of unsufficient privileges on DBMS_SCHED_JOB_EXPORT.GRANT_EXP, but I am not sure who needs what grant.
Could you please advise on how to resolve the issue?
ThanksHi,
Can anyone help if possible please?
Thanks -
Oracle error ORA-39127 unexpected error from call to export_string
Hi
The export for an database encounters the following error .Can someone take a look at the cause please.
Processing object type DATABASE_EXPORT/SYSTEM_PROCOBJACT/PRE_SYSTEM_ACTIONS/PROCACT_SYSTEM
Processing object type DATABASE_EXPORT/SYSTEM_PROCOBJACT/PROCOBJ
ORA-39127: unexpected error from call to export_string :=SYS.DBMS_SERVER_ALERT_EXPORT.SYSTEM_INFO_EXP(1,dynconnect,'11.02.00.02.00',newblock)
ORA-13914: Threshold notification failed.
ORA-06512: at "SYS.DBMS_SERVER_ALERT", line 187
ORA-06512: at "SYS.DBMS_SERVER_ALERT_EXPORT", line 132
ORA-06512: at line 1
ORA-06512: at "SYS.DBMS_METADATA", line 7418
Processing object type DATABASE_EXPORT/SYSTEM_PROCOBJACT/POST_SYSTEM_ACTIONS/PROCACT_SYSTEM
Processing object type DATABASE_EXPORT/SCHEMA/PROCACT_SCHEMA
Processing object type DATABASE_EXPORT/SCHEMA/TABLE/TABLE
Processing object type DATABASE_EXPORT/SCHEMA/TABLE/PRE_TABLE_ACTION
RegardsThere are a lot of similar errors on MOS, perhaps you should search through them and see if any apply to you.
What version/patch level are you on? Have you made any grid control threshold modifications? Are you using procobol in an upgraded database?
You might want to go through support for this one. -
ORA-39127: unexpected error from call to
Hi ALL.
11.2.0.3
Is this a bug?
I got error when running expdp system/manager full=yes
ORA-39127: unexpected error from call to "SYS"."DBMS_JVM_EXP_PERMS"."GRANT_SYSPRIVS_EXP"But it works fine on 11.2.0.1
Any ideas and solutions please.....
Thanks a lot,hello,
You may look into the following My Oracle Support Document: DataPump Export (EXPDP) Failed On Identifier SYS.DBMS_JVM_EXP_PERMS Must Be Declared [ID 1095533.1]
According to the document the versions affected are 10gR2 and 11gR1, but, the workaround may solve your issue.
Hope it helps. -
Unable to transfer a second incoming call from my Cisco IP Phone 7940
1) A call comes into reception (call A).
2) The receptionist answers the call A / Client A.
3) While the receptionist is talking with the client (A), the screen displays the options 'Transfer' etc until then she can transfer the call.
4) Then comes a second call, the call 'B', and then 'transfer' softkey disappear displays options 'Answer' . At that time the receptionist can not transfer the call 'A' until she answers the call B.
She couldn't transfer calls until she answers all incoming callsduplicate
https://supportforums.cisco.com/discussion/12255956/unable-transfer-second-incoming-call-my-cisco-ip-phone-7940 -
CUPC 8.5.5 click to call from outlook 2007 challenges
Hello all,
The challenge I am having is that some ckient users are not recieving the abilty to click to call from there outlook address book. The actions button is greyed out (picture attached) from the address book.
version we are using currently is 8.5.5.19839. Windows 7 64 bit, Office 2007.
What shoul I be looking at for these users? I have the same set up with no issues. Any suggestions in the right direction would be helpful.
cheers
scottThere is an enhancement bug already filed for this feature. http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCtd16602
Internally, I could see some activity on it during October 2011 as of recent.The action is still pending. For further details, yes TAC can be very much approached.
If the info helps, please rate the post.
GP. -
Video doesn't work when calling from Jabber to DX650
Hi,
I just added a DX650 to our CUCM 9.1.2. When I call from either Jabber to the DX650 or Lync to DX650, the video doesn't work and the call is audio only. The message i'm seeing on Jabber is something like "the other endpoint is not accepting video." Sorry i don't remember the exact message. Has anyone seen this issue before? Thanks!Lync is not standards based and has proprietary codecs for video. You will need a Expressway with the MS Interop key to get video both ways.
https://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/X8-2/Cisco-VCS-Microsoft-Lync-Deployment-Guide-X8-2.pdf -
How can i transfer a call from SIP 9971 to PBX system on CME router
hello everybody,
I have a critical problem about interaction of transfering feature between CME router and pbx panasonic system in some status. let me explain more detail about this issue..i have a SIP 9971(CP-9971) registered on CME at the one site and a voice gateway that is connect with PBX system through a E1 pri trunk connection at the other site. totally the integration between CME and PBX is ok and there is no problem in two direction, i mean i can call pbx system from cp-9971 and vise versa but when i call from a phone which is registered on PBX site to SIP 9971 which is registered on cisco CME call is connected,then when i try to transfer that call to another phone at PBX site, the session is open between two panasonic phones but no audio transmited in two direction. in addition every thing works fine about SCCP phones(transfer feature works fine). here is my configuration file. i hope someone could help me because i've searched a lot but no result help help help plz....
cme router 3845 configuration
VOIP-3845#show running-config
Building configuration...
Current configuration : 12657 bytes
! Last configuration change at 11:44:01 UTC Mon Oct 31 2011 by admin
! NVRAM config last updated at 11:44:02 UTC Mon Oct 31 2011 by admin
! NVRAM config last updated at 11:44:02 UTC Mon Oct 31 2011 by admin
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname VOIP-3845
boot-start-marker
boot-end-marker
no aaa new-model
clock calendar-valid
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
sip
bind control source-interface Loopback10
bind media source-interface Loopback10
registrar server
voice register global
mode cme
source-address 192.168.2.1 port 5060
max-dn 720
max-pool 262
load 9971 sip9971.9-1-1SR1.loads
authenticate register
authenticate realm cisco.com
tftp-path flash:
file text
create profile sync 0063544528862458
camera
video
voice register dn 1
number 500
voice register dn 2
number 600
voice register dn 3
number 700
name test
voice register template 1
softkeys idle Newcall Redial Cfwdall
softkeys connected Confrn Endcall Hold Trnsfer
voice register pool 1
id mac B8BE.BF23.5242
type 9971
number 1 dn 1
template 1
username test password test
camera
video
blf-speed-dial 4 600 label "test"
voice register pool 2
id mac B8BE.BF9C.5476
type 9971
number 1 dn 2
template 1
username bank password bank
camera
video
voice register pool 3
id mac B8BE.BF9C.51D4
type 9971
number 1 dn 3
template 1
username test1 password test1
camera
video
voice register pool 4
id mac B8BE.BF9C.4FA2
number 1 dn 1
camera
video
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1576175886
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1576175886
revocation-check none
rsakeypair TP-self-signed-1576175886
crypto pki certificate chain TP-self-signed-1576175886
certificate self-signed 01
30820241 308201AA A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31353736 31373538 3836301E 170D3131 31303038 30393034
34365A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 35373631
37353838 3630819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100D6EC 47BCDC3C 82F43FF3 23522678 2616868D 9910DCD2 E36016B3 D7B40DA7
53A6E339 4978D451 21F051BE B21F8AD5 86B952DC 1ECCE371 3E094B54 26A41E14
A3055C06 AE860756 425E5C50 E62B3287 631B1E87 9BAC2E39 2810E120 DA3BF823
947EA591 81CA5489 1B868239 E835EC7C 0AA7651A 22D6E47F 545EBEF3 A172C9A3
5A0D0203 010001A3 69306730 0F060355 1D130101 FF040530 030101FF 30140603
551D1104 0D300B82 09564F49 502D3338 3435301F 0603551D 23041830 1680146C
934AD072 99DDC600 ECD6F389 8F71E0C2 18EC2E30 1D060355 1D0E0416 04146C93
4AD07299 DDC600EC D6F3898F 71E0C218 EC2E300D 06092A86 4886F70D 01010405
00038181 000E82F6 5FBB847C 49226955 6F7DECE7 0B093513 D57C35D5 4CD22FA7
8144A080 B0D56C8D 86AF8156 0152443A A3FBE59F B1AEFFBC BEB43E09 35757BAD
4C06FC4A 0F3695E0 B00FBD30 4E8F36CE 7748F39C F9602650 7A1D2D48 DBC31237
AE3D63CE 593D31F5 62E4916F D20E30E8 30DC55C0 120FBD26 D2768DBC A67DDC34
5BDB66B1 E3
quit
license udi pid CISCO3845-MB sn FOC14421Q1Y
archive
log config
hidekeys
username admin privilege 15 secret 5 $1$Zf7j$P93opukmmEBIioVpjmHB3.
redundancy
interface Loopback10
ip address 192.168.2.1 255.255.255.0
interface Tunnel1
ip address 172.25.10.1 255.255.255.0
no ip redirects
ip nhrp map multicast dynamic
ip nhrp network-id 10
tunnel source GigabitEthernet0/1.1
tunnel mode gre multipoint
tunnel key 100
interface Tunnel2
ip address 172.25.11.1 255.255.255.0
no ip redirects
ip nhrp map multicast dynamic
ip nhrp network-id 20
tunnel source GigabitEthernet0/1.2
tunnel mode gre multipoint
interface Tunnel14
ip address 192.168.13.129 255.255.255.252
tunnel source GigabitEthernet0/1.1
tunnel destination 10.2.68.25
interface Tunnel18
ip address 192.168.13.137 255.255.255.252
tunnel source GigabitEthernet0/1.1
tunnel destination 10.9.160.236
interface GigabitEthernet0/0
no ip address
shutdown
duplex auto
speed auto
media-type rj45
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
media-type rj45
interface GigabitEthernet0/1.1
encapsulation dot1Q 10
ip address 10.9.160.25 255.255.255.0
interface GigabitEthernet0/1.2
encapsulation dot1Q 50
ip address 10.10.9.25 255.255.255.0
router eigrp 202
network 172.25.11.0 0.0.0.255
network 192.168.2.0 0.0.0.15
redistribute static route-map MYMAP1
router eigrp 201
network 172.25.10.0 0.0.0.255
network 192.168.2.0 0.0.0.15
redistribute static route-map MYMAP1
ip forward-protocol nd
ip http server
ip http secure-server
ip http path flash:/gui
ip route 10.2.68.0 255.255.255.0 10.9.160.1
ip route 10.10.0.0 255.255.0.0 10.10.9.1
ip route 10.64.164.30 255.255.255.255 10.9.160.1
ip route 192.168.14.0 255.255.255.0 192.168.13.130
ip route 192.168.17.0 255.255.255.0 Tunnel18
ip access-list standard REDIS1
permit 192.168.14.0
permit 192.168.17.0
route-map MYMAP1 permit 10
match ip address REDIS1
snmp-server community test RO
tftp-server flash:term11.default.loads
tftp-server flash:dkern9971.100609R2-9-0-3.sebn
tftp-server flash:kern9971.9-0-3.sebn
tftp-server flash:rootfs9971.9-0-3.sebn
tftp-server flash:sboot9971.111909R1-9-0-3.sebn
tftp-server flash:sip9971.9-0-3.loads
tftp-server flash:skern9971.022809R2-9-0-3.sebn
tftp-server flash:sccp11.9-0-2sr1s
tftp-server flash:SCCP11.9-1-1SR1S.loads
tftp-server flash:apps11.9-1-1TH1-16.sbn
tftp-server flash:cnu11.9-1-1TH1-16.sbn
tftp-server flash:cvm11sccp.9-1-1TH1-16.sbn
tftp-server flash:dsp11.9-1-1TH1-16.sbn
tftp-server flash:jar11sccp.9-1-1TH1-16.sbn
tftp-server flash:term06.default.loads
tftp-server flash:sip9971.9-1-1SR1.loads
tftp-server system:cme/sipphone
tftp-server flash:Desktops/320x212x12/NantucketFlowers.png
tftp-server flash:Desktops/320x212x12/TN-CampusNight.png
tftp-server flash:Desktops/320x212x12/TN-CiscoFountain.png
tftp-server flash:Desktops/320x212x12/TN-Fountain.png
tftp-server flash:Desktops/320x212x12/TN-MorroRock.png
tftp-server flash:Desktops/320x212x12/TN-NantucketFlowers.png
tftp-server flash:Desktops/320x212x12/Fountain.png
tftp-server flash:Desktops/320x212x12/CiscoLogo.png
tftp-server flash:Desktops/320x212x12/TN-CiscoLogo.png
tftp-server flash:Desktops/320x212x12/List.xml
tftp-server flash:Desktops/320x216x16/List.xml
tftp-server flash:Desktops/320x212x16/List.xml
tftp-server flash:gui/admin_user.html
tftp-server flash:gui/admin_user.js
tftp-server flash:gui/CiscoLogo.gif
tftp-server flash:gui/Delete.gif
tftp-server flash:gui/dom.js
tftp-server flash:gui/downarrow.gif
tftp-server flash:gui/ephone_admin.html
tftp-server flash:gui/logohome.gif
tftp-server flash:gui/normal_user.html
tftp-server flash:gui/normal_user.js
tftp-server flash:gui/Plus.gif
tftp-server flash:gui/sxiconad.gif
tftp-server flash:gui/Tab.gif
tftp-server flash:gui/telephony_service.html
tftp-server flash:gui/uparrow.gif
tftp-server flash:gui/xml-test.html
tftp-server flash:gui/xml.template
tftp-server flash:ringtones/Analog1.raw
tftp-server flash:ringtones/Analog2.raw
tftp-server flash:ringtones/AreYouThere.raw
tftp-server flash:ringtones/AreYouThereF.raw
tftp-server flash:ringtones/Bass.raw
tftp-server flash:ringtones/CallBack.raw
tftp-server flash:ringtones/Chime.raw
tftp-server flash:ringtones/Classic1.raw
tftp-server flash:ringtones/Classic2.raw
tftp-server flash:ringtones/ClockShop.raw
tftp-server flash:ringtones/DistinctiveRingList.xml
tftp-server flash:ringtones/Drums1.raw
tftp-server flash:ringtones/Drums2.raw
tftp-server flash:ringtones/FilmScore.raw
tftp-server flash:ringtones/HarpSynth.raw
tftp-server flash:ringtones/Jamaica.raw
tftp-server flash:ringtones/KotoEffect.raw
tftp-server flash:ringtones/MusicBox.raw
tftp-server flash:ringtones/Piano1.raw
tftp-server flash:ringtones/Piano2.raw
tftp-server flash:ringtones/Pop.raw
tftp-server flash:ringtones/Pulse1.raw
tftp-server flash:ringtones/Ring1.raw
tftp-server flash:ringtones/Ring2.raw
tftp-server flash:ringtones/Ring3.raw
tftp-server flash:ringtones/Ring4.raw
tftp-server flash:ringtones/Ring5.raw
tftp-server flash:ringtones/Ring6.raw
tftp-server flash:ringtones/Ring7.raw
tftp-server flash:ringtones/RingList.xml
tftp-server flash:ringtones/Sax1.raw
tftp-server flash:ringtones/Sax2.raw
tftp-server flash:ringtones/Vibe.raw
tftp-server flash:APPS-1.2.1.SBN
tftp-server flash:SYS-1.2.1.SBN
tftp-server flash:GUI-1.2.1.SBN
tftp-server flash:CP7921G-1.2.1.LOADS
tftp-server flash:TNUX-1.2.1.SBN
tftp-server flash:TNUXR-1.2.1.SBN
tftp-server flash:WLAN-1.2.1.SBN
tftp-server flash:apps37sccp.1-2-1-0.bin
tftp-server flash:APPSH-1.3.1.SBN
tftp-server flash:GUIH-1.3.1.SBN
tftp-server flash:CP7925G-1.3.1.LOADS
tftp-server flash:SYSH-1.3.1.SBN
tftp-server flash:TNUXH-1.3.1.SBN
tftp-server flash:WLANH-1.3.1.SBN
tftp-server flash:SCCP11.9-2-1S.loads
tftp-server flash:Desktops/320x212x12/CampusNight.png
tftp-server flash:Desktops/320x212x12/CiscoFountain.png
tftp-server flash:Desktops/320x212x12/MorroRock.png
tftp-server flash:skern9971.022809R2-9-2-1.sebn
tftp-server flash:sip9971.9-2-1.loads
tftp-server flash:sboot9971.031610R1-9-2-1.sebn
tftp-server flash:rootfs9971.9-2-1.sebn
tftp-server flash:dkern9971.100609R2-9-2-1.sebn
tftp-server flash:kern9971.9-2-1.sebn
tftp-server flash:United_States/g4-tones.xml
tftp-server flash:English_United_States/gd-sip.jar
tftp-server flash:sboot9971.031610R1-9-1-1SR1.sebn alias sboot9971.031610R1-9-1-1SR1.sebn
tftp-server flash:rootfs9971.9-1-1SR1.sebn alias rootfs9971.9-1-1SR1.sebn
tftp-server flash:kern9971.9-1-1SR1.sebn alias kern9971.9-1-1SR1.sebn
tftp-server flash:dkern9971.100609R2-9-1-1SR1.sebn alias dkern9971.100609R2-9-1-1SR1.sebn
tftp-server flash:skern9971.022809R2-9-1-1SR1.sebn alias skern9971.022809R2-9-1-1SR1.sebn
control-plane
mgcp profile default
dial-peer voice 1 voip
description connection-trough-PBX
destination-pattern 0....
session target ipv4:192.168.13.130
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 100 voip
description K
destination-pattern 9T
session target ipv4:192.168.13.130
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 5 voip
shutdown
destination-pattern *3709
session protocol sipv2
session target ipv4:192.168.13.130
session transport tcp
dtmf-relay h245-alphanumeric
codec g711ulaw
no vad
dial-peer voice 2 pots
incoming called-number .
dial-peer voice 10 voip
gatekeeper
shutdown
telephony-service
em logout 0:0 0:0 0:0
max-ephones 262
max-dn 400
ip source-address 192.168.2.1 port 2000
load 7911 SCCP11.9-2-1S
max-conferences 12 gain -6
web admin system name admin secret 5 $1$IKnn$tyKyuBcGqXFl6nhxCSu.z0
dn-webedit
time-webedit
transfer-system full-consult
transfer-pattern .T
create cnf-files version-stamp 7960 Oct 29 2011 12:39:25
ephone-template 1
softkeys connected Confrn Endcall Trnsfer Hold
keep-conference endcall
ephone-dn 1 dual-line
number 200
label test
name test
ephone-dn 2 dual-line
number 300
label Sepahbod
name Sepahbod
ephone-dn 4 dual-line
number 666
ephone-dn 5 dual-line
number 660
ephone-dn 6 dual-line
number 670
ephone-dn 7 dual-line
number 770
ephone-dn 8 dual-line
number 770
ephone-dn 9 dual-line
number 999
ephone 1
device-security-mode none
mac-address 18EF.639F.BCB0
keep-conference endcall
button 1:1
ephone 2
device-security-mode none
mac-address 0025.8418.B017
ephone-template 1
keep-conference endcall
button 1:2
ephone 3
device-security-mode none
mac-address F04D.A243.3154
keep-conference endcall
button 1:4
ephone 4
device-security-mode none
mac-address 6CF0.496A.69E9
button 1:4
ephone 5
device-security-mode none
mac-address 0015.E987.345F
keep-conference endcall
button 1:5
ephone 6
device-security-mode none
mac-address 0024.1DEA.614A
keep-conference endcall
button 1:6
ephone 9
device-security-mode none
mac-address 001D.7D4D.4DCB
button 1:9
line con 0
line aux 0
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
end
and Voice Gateway connected two PBX system configuration
Current configuration : 3486 bytes
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Voice-GW
boot-start-marker
boot-end-marker
card type e1 0 2
no aaa new-model
network-clock-participate wic 2
dot11 syslog
ip source-route
ip cef
no ipv6 cef
multilink bundle-name authenticated
isdn switch-type primary-net5
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
h323
voice-card 0
crypto pki token default removal timeout 0
license udi pid CISCO2811 sn FHK1352F0E9
username admin privilege 15 secret 5 $1$O6AN$1kvvqiLdIl3/ZTHoyYRy0/
redundancy
controller E1 0/2/0
framing NO-CRC4
pri-group timeslots 1-31
controller E1 0/2/1
interface Tunnel14
ip address 192.168.13.130 255.255.255.252
tunnel source FastEthernet0/1
tunnel destination 10.9.160.25
interface Tunnel17
ip address 192.168.13.134 255.255.255.252
tunnel source FastEthernet0/1
tunnel destination 10.9.160.25
interface FastEthernet0/0
ip address 192.168.14.252 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.2.68.25 255.255.255.0
duplex auto
speed auto
interface Serial0/2/0:15
no ip address
encapsulation hdlc
isdn switch-type primary-net5
isdn overlap-receiving
isdn incoming-voice voice
no cdp enable
router eigrp 201
network 172.25.10.0 0.0.0.255
network 192.168.14.0
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 10.9.160.0 255.255.255.0 10.2.68.1
ip route 10.128.0.69 255.255.255.255 Tunnel14
ip route 192.168.2.1 255.255.255.255 192.168.13.129
ip route 192.168.17.0 255.255.255.0 Tunnel14
tftp-server flash:SCCP11.9-2-1S.loads
tftp-server flash:jar11sccp.9-2-1TH1-13.sbn
tftp-server flash:dsp11.9-2-1TH1-13.sbn
tftp-server flash:cvm11sccp.9-2-1TH1-13.sbn
tftp-server flash:cnu11.9-2-1TH1-13.sbn
tftp-server flash:apps11.9-2-1TH1-13.sbn
control-plane
voice-port 0/0/0
caller-id enable
voice-port 0/0/1
voice-port 0/0/2
supervisory disconnect dualtone mid-call
dial-type pulse
disc_pi_off
output attenuation 1
echo-cancel coverage 32
timeouts call-disconnect 5
timeouts wait-release 1
timing hookflash-out 50
timing sup-disconnect 50
connection plar 600
caller-id enable
voice-port 0/0/3
caller-id enable
voice-port 0/2/0:15
mgcp profile default
dial-peer voice 1 pots
description connection-to-PBX
destination-pattern 0....
direct-inward-dial
port 0/2/0:15
forward-digits 4
dial-peer voice 10 voip
destination-pattern ...
session target ipv4:192.168.13.129
dtmf-relay h245-alphanumeric
no vad
dial-peer voice 20 pots
description FXO-K
destination-pattern 9T
progress_ind alert enable 8
progress_ind progress enable 8
progress_ind connect enable 8
direct-inward-dial
port 0/0/2
prefix 9
dial-peer voice 30 pots
description FXO-K2
destination-pattern 9T
direct-inward-dial
port 0/0/1
prefix 9
telephony-service
max-ephones 20
max-dn 100
ip source-address 192.168.14.252 port 2000
cnf-file location flash:
load 7911 term11.default.loads
max-conferences 8 gain -6
transfer-system full-consult
create cnf-files version-stamp Jan 01 2002 00:00:00
ephone-dn 1
number 770
line con 0
line aux 0
line 1/0 1/15
line vty 0 4
login local
transport input telnet
scheduler allocate 20000 1000
endHaving looked at your spreadsheet I see you're failing H323 transfers back to your ISDN system, but only under certain circumstances. Quite why, I'm not sure, possibly because you haven't codec defined on your H323 dial peers. or it could be something else
I think you may be able to work around the problem by adding
" supplementary-service h450.12 " under voice service voip on your CME router as a quick fix.
reference
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmetrans.html#wpxref44614
worth a try
Adam
Maybe you are looking for
-
I want to use ETHERNET and not PROFIBUS to communicate and I think you can do that with only the applicom software SW-1000ETH. You must just have an ethernet card on your PC. So, you could use a notebook with an ethernet card. You can also use Applic
-
Compaq Presario 2710CA Start Up problems after virus attack!
Hello, I am having great difficulty with my Presario 2710CA following a 'Windows Recovery' Virus attack. After removal of the virus (I used the MalwareBytes Anti Malware for the clean up), I rebooted the machine as required but now getting the error
-
How To: Use ADF Form in "Insert" Mode in jDeveloper 12c
Hi all, I'm in the process of learning jDeveloper and after going through the basics, a task that I'm trying to accomplish is to have a ADF Form load in "Insert" mode rather than the default "Update" behavior. After significant searches, the closest
-
Playlist Broadcaster problems after 24 hours
I have a simple video (MPEG4 video/AAC audio) that continually loops. It seems that after 24 hours, when the video is access in QuickTime Player or the plugin in a web page that the audio will drop out but the video continues to play OR the video wil
-
IPod Shuffle - using it on two computers wipes the contents
I have an old iPod shuffle first generation with most of my music on my laptop. I actually have very little music on, and I have some different music on my main iMac. I want to plug the iPod into big iMac to charge it, but when I do that it wipes a