Unidentified network" with Server 2012 R2 and windows 8- Domain & NIC teaming

i have problem with my network ,before that i had just my domain but now some servers  specially win 2012 detect a network (name:network 4)
my 2012 windows server cannot be joined to doman also windows 8,but sometimes this problem solves without any troubleshooting and i can join again
what can be problem
S.Sanadi

Hi S.Sanadi,
According to your description, my understanding is that “Unidentified Network” causes problem with joining domain, and this problem will be resolved automatically.
If there is no default gateway or the default gateway is useless, the network will be identified as unknown. Check to see if the IP configuration is correct when the network identified unknown. Open command prompt and type:
Ipconfig /all
If the parameter is correct, try to ping IP address of default gateway and check to see if it works well.
Besides, if the connection should be identified as a Domain network and is not, then the likely causes are failure to contact DNS servers or domain controllers on that interface. Ping the IP address of DNS server and DC to make sure that these resources
are available.
Regards,           
Eve Wang

Similar Messages

  • Folder Redirection GPO with Server 2012 R2 and Windows 7

    Hey folks,
    I have recently migrated from 2008 R2 to 2012 R2. I have set up a new GPO to redirect: Desktops & My Documents to the server \\dc.companyname.local\folder_redirections\  on all the windows 7 desktops
    in the office.  
    The problem i ahve having is that when i run gpresult is says that the GPO is being applied but when i check the location of the mentioned locations they are still pointing to the local desktop or the old 2008r2
    server. I have double checked the permission on the share folder and i have even set upo a test folder with everyone having full rights and it still will not
    redirect the folders...  any ideas would be most welcome!
    I cannot post pictures yet until i am verified :)

    > locations they are still pointing to the local desktop or the old 2008r2
    Check event logs. Folder redirection creates events if things go wrong...
    Martin
    Mal ein
    GUTES Buch über GPOs lesen?
    NO THEY ARE NOT EVIL, if you know what you are doing:
    Good or bad GPOs?
    And if IT bothers me - coke bottle design refreshment :))

  • Just FYI, Windows Server 2012 R2 and Windows Server 2012 BranchCache Deployment Guide in Word format in the TechNet Gallery

    The Windows Server 2012 R2 and Windows Server 2012 BranchCache Deployment Guide is now available for download in Word format in the TechNet Gallery at
    http://bit.ly/1pYZT3F
    Thanks -
    James McIllece

    hello again,
    meanwhile I was lucky to find this article about Idenity Mapping in TechNet in the Storage Team Blog:
    http://blogs.technet.com/b/filecab/archive/2012/10/09/nfs-identity-mapping-in-windows-server-2012.aspx
    Likely to be overseen at the end of one paragraph it says:
    "Client for NFS does not support NFS V4.1 in Windows 8 or Windows Server 2012"
    Question : Is this an official statement and is it still valid with most recent
    Windows Server 2012 R2 that NFS client does NOT support NFSv4.x  ??
    thanks - Rainer

  • DirectAccess Windows Server 2012 R2 and Windows 8.1 - status connecting

    I've successfully deployed DirectAccess on Windows Server 2012 R2 in a 2 node NLB cluster. Everything in the console is green and I can see clients connecting.
    Windows 7 clients can connect and with the DirectAccess connectivity assistant installed show as connected and I can access resources.
    On a Windows 8.1 client I can access resource and run the troubleshooting tool which reports no errors, but if I look at connections it shows as connecting and the status never changes to connected. Clients work correctly when on the internal network.
    I've looked at available hotfixes, but not found anything for when the status is incorrectly shown.
    Any ideas before I raise a support call?
    James Saunders

    Hi,
    You current information hardly determine which part may occur error, I found the similar symptom on the following third party article, may can give you some help.
    The similar issue third party article:
    Windows 8 DirectAccess client keeps saying "Connecting"
    http://tfs.letsblog.it/post/2013/07/10/Windows-8-DirectAccess-client-keeps-saying-Connecting.aspx
    More information:
    The Network Connection Status Icon
    http://blogs.technet.com/b/networking/archive/2012/12/20/the-network-connection-status-icon.aspx
    Hope this helps.
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • DirectAccess Client not connecting without error code on Windows Server 2012 R2 and Windows 8.1

    Hello,
    we are currently migrating from Windows Server 2012 to 2012 R2 and are not able to get the new Direct Access Service up and running. Our goal is to establish DirectAccess connection for a handful of clients using the IPHTTPS-adapter on the default port 443.
    Errors:
    There is actually no error showing up. It seems the infrastructure tunnel cannot be created but none of the IPv6-transition adapters is connecting (teredo and 6-to-4 are down) and the IPHTTPs adapter gives no informations about a problem:
    >Get-DAConnectionStatus
    Status    : Error
    Substatus : CouldNotContactDirectAccessServer
    >Get-NetIPHttpsState
    LastErrorCode   : 0x0
    InterfaceStatus : Failed to connect to the IPHTTPS server; waiting to reconnect
    Setup:
    Our setup is a virtualized Windows Server 2012 R2 Standard running on Hyper-V. It is located behind a NAT having the Port 443 mapped to the server. The only role installed after the basic install is RRAS including DirectAccess and VPN. The assistants completed
    successfully (running the configuration for DirectAccess and VPN). Operation Status says everything is green und working (for multiple days in the meanwhile). A previous direct access installation (on a different machine running Windows Server 2012) has
    been removed before installing the new server. The new installation is using a different router, so this might also be the cause of a problem.
    The client is a Windows 8.1 notebook located outside the company network accessing the internet through another NAT-device. The client has been able to connect to the previous DirectAccess setup but has never been able to establish a connection after the
    setup of the new Direct Access server. The device has no outbound constraints concerning the NAT-device and is only running the integrated Windows Firewall.
    Diagnosis:
    So far I've done some basic DNS and connectivity checks. The DNS-name can be resolved correctly and the router even responds to pings. The port forward is working and HTTPs connections are generally possible (temporarily routed the port to
    access the NLS-Website located on the server, which worked fine).
    Network monitor shows that both computers are communicating, traffic on the expected Port 443 is incoming on the server and responses from the server reach the client.
    Opening the IPHTTPs-url and in an endless page load. Sometime the browser page closes but I've never seen any result. Using telnet on the port shows that the server is accepting connections. I've even build a small test application that does a GET-Request
    on the URL returning HTTP-200 and no content.
    I'm currently running out of ideas what to do and since no error occurs this is kind of a bit frustrating. Any help appreciated.
    Regards
    Matthias

    Hi,
    In addition, have you disabled the DA client components on the DA client? If no, please also check
    the settings on the Name Resolution Policy Table.
    More information:
    DirectAccess
    Client Location Awareness – NRPT Name Resolution
    In addition, error 0x4C9 means the remote computer refused the network connection. It may be due to the invalid
    registry or corrupt drivers. For more detailed information, please refer to the link below:
    Error 1225 - Error Code 0x4C9
    Note:
    Microsoft is providing this information as a convenience to you. Please make sure that you completely understand the risk before retrieving any suggestions from the above link.
    Best regards,
    Susie

  • OTP 2FA Problems with DA 2012 R2 and Windows 8.1 Client - Not prompting or OTP Code

    Hi 
    Just seeing if anyone has come across the same issue with their WIn 8.1 clients not prompting for 2FA once configured with DirectAccess 2012 R2?
    I have created the 2x OTP certificates, enabled OTP via PowerShell and set up the RADIUS server but whatever happens the Win 8.1 client does not get prompted for 2FA - They connect seamlessly?
    I have also configured the DAProbeUser on the RADIUS server
    Any help appreciated
    Thanks

    I was afraid that you'll said that
    I hate to be the annoying guy but take a look at this KB article:
    http://support.microsoft.com/kb/2787534
    Applied to: Windows 8\2012,
    Doesn't Apply to: Windows 8.1\2012 R2
    and - for a fact, doesn't include in Windows 8.1\2012 R2 as this bug still exists in those operating systems.
    another annoying fact - No other update was released for these version yet.
    this example approves that not every hotfix \ updates that was released for 8\2012 before 8.1\2012 R2, is already included in 8.1\2012 R2
    and allow me to add another fact.
    when you configure DirectAccess via the remote access wizard it creates a WMI query called
    DirectAccess - Laptop Only WMI Filter.
    after you create it in Windows Server 2012 R2 - look at the WMI Query and you'll see that by default it doesn't apply to version 6.3! the version for Windows 8.1.
    if you want to add the support for Windows 8.1 you have to modify manually the query which is of course, not supported by Microsoft.
    That is just another symptom that makes me wonder if Microsoft did ANY change or update to DirectAccess 2012 R2
    Tamir Levy

  • Adding Administrative Templates (.admx) for Windows 8 and Windows Server 2012 to my Windows 2008 domain

    Hi,
    We have a Windows 2008 domain, and now we need to configure IE 10 options, so we have to import the Windows 8 / 2012 ADMX files. Can we just do the following:
    1. Download
    http://www.microsoft.com/en-us/download/details.aspx?id=36991
    2. Unzip it and copy the .admx files to c:\Windows\Sysvol\<domain>\policies and create a directory called policydefinitions
    3. Then just re-open Group Policy Management ?
    Correct way or not? Will this have any implication on network or any old GPO.
    Thanks for reply
    /Regards Andreas

    > But i cant seem to find "Check for publisher`s certificate revocation",
    > so how can i disable this. I did see a url to create a ADML file, but
    > this was very old.
    Doesn't exist - only "Server certificate". The old URL might still be valid.
    Martin
    Mal ein
    GUTES Buch über GPOs lesen?
    NO THEY ARE NOT EVIL, if you know what you are doing:
    Good or bad GPOs?
    And if IT bothers me - coke bottle design refreshment :))

  • Purchase of server 2012 OLP and windows 8.1 enterprise OLP

    i want to buy/purchase official DVD's of the  
    1: WINDOWS 8.1 ENTERPRISE LICENSES FOR OLP
    2: SERVER 2012 R2 LICENSES OLP
    (for charity hospital)
    my location is Pakistan can any one guide me the official way and process. 

    Hi,
    Regarding to your issue, I suggest that you should contact Microsoft Customer Service center in Pakistan. I
    believe we will get a better assistance there.
    For more details, please refer to
    Global Customer Service phone numbers.
    Hope this helps.
    Best regards,
    Justin Gu

  • Network with XP (32 bit) and Windows 8.1(64 bit)

    The HP printer F4280 is connected directly to the XP computer and via a wired modem network connection to the Windows 8.1 computer.
    The XP computer gets perfect prints. The Windows 8.1 computer gets incomplete prints - the shaded stuff is printed, the plain print is missing.
    I tried new drivers on each - the XP only accepts a 32 bit driver. I put a 64 bit driver on the Windows 8.1 computer - nothing improved the 8.1 prints.
    What can I do??
    This question was solved.
    View Solution.

    Actually the network setup we have works fine for most print jobs from the Widows 8.1 computer. The one case of difficulty involved an Adobe Readert file on my Widows 8.1 computer that failed to print fully on the HP printer on the other computer. I think Adobe Reader is the problem or the file set up by the site with the file I wanted to print.
    Generally speaking the HP set up we have works well most of the time, even with Adobe Reader files. But that one file was a mess and caused my concern. I can live with it, I think!

  • Is it possible to uninstall IE 11 from Windows Server 2012 R2 and replace it with the latest version of IE 10?

    Is it possible to uninstall IE 11 from Windows Server 2012 R2 and replace it with the latest version of IE 10? We have a remote desktop farm setup with 2012 R2 servers and we are publishing some web links that only work with IE10. As a result, we need to
    downgrade the remote desktop servers to IE10. I have a feeling that this isn't possible, but if I could get a definitive answer, I would greatly appreciate it, thank you!

    Hi,
    Agreed with DonPick.
    Internet Explorer 11 is preinstalled with Windows 8.1 and Windows Server 2012 R2.
    More information regarding Internet Explorer 11, please check:
    Internet Explorer 11 - FAQ for IT Pros
    http://msdn.microsoft.com/en-us/library/dn268945.aspx
    Best regards
    Michael Shao
    TechNet Community Support

  • Windows Server 2012 Standard and Essentials User CAL's

    I've been running Windows Server 2012 Essentials in an organization that until recently stayed within the 25 user 50 network device limit specified by the license. Eventually we've grown beyond that. Since the Server 2012 Essentials machine had a non-transferable
    OEM license I decided not to waste it by doing an in-place migration to Server 2012 Standard, and instead set up a new server with freshly purchased Server 2012 R2 Standard and migrated Active Domain roles to it, leaving the original server as a part of a
    fail-over cluster.
    We purchased 30 User CAL's for the 2012 R2, as required for 25+ staff members.
    Now I am curious. The 2 servers that we have right now (2012 R2 Standard and 2012 Essentials) both maintain the same Active Directory and manage the same pool of users and workstations. Does that mean that the primary server with 30 User CAL's takes dominance
    and sets the limit as to how many people are allowed to access the network. Or does it become a combination of purchased 30 CAL's + 25 Users hard-wired into the 2012 Essential edition?
    Do these servers have to run separate domains with segregated pools of users in order to be license compliant for 30+ users or can they exist within the same same domain preserving individual user limits? What if the 2012 Essentials server maintains
    one office location with fewer than 25 staff and the Standard R2 2012 server runs another office with fewer than 30 staff, while both offices are linked via a VPN for the purpose of sharing 3rd party licenses? Do individual user limits apply, or is it still
    30 users max?
    To sum up the question, I'd like to know whether I'd need to buy more user CAL's when we reach more than 30 staff at 1 or possibly 2 office locations.
    Oh, and the device limit! 2012 R2 Standard under user CAL licensing scheme has no machine limits. Essentials is always capped at 50. When running one active directory, what's the legally allowed number of devices on the network? I assume it's unlimited.
    Thanks.

    Thank you for the reply.
    My question then is how to transition while preferably keeping both physical servers.
    Should a 2012 Standard key be purchased additionally for an in-place transition of 2012 Essentials machine to 2012 Standard (which at this point is as good as a fresh install)? Until then, should the Essentials 2012 server be taken offline entirely?
    What about the situation where I described both servers running segregated networks with their own pools of users, only connected via a VPN for 3rd party license sharing? Is that configuration supported?
    Also, if the configurations is unsupported, why are the servers able to share roles in first place? Why isn't there a software mechanism preventing interaction? What configuration do the servers themselves assume is in place?
    Thanks again.

  • How do I do a Windows 7 restore as a Hyper-V clent with Server 2012 Essentials R2?

    How do I do a Windows 7 restore as a Hyper-V client with Server 2012 Essentials R2?  There is no client restore CD available as an ISO to mount as the CD.
    Scott

    Hi,
    As we know, to simplify the bare metal restore scenario, we implemented the Client Restore Service in Windows Server 2012 R2 Essentials, which will enable WDS on the Windows Server Essentials
    server and configure the client restore image as a boot image. With the Client Restore Service turned on, the administrator can initiate a PXE boot on a client computer by using a network interface to launch the Client Restore Wizard and restore the client
    computer. There’s no need to prepare a client restore DVD, or a client restore USB bootable key. For details about how to perform the client restore, please refer to the following article.
    Set Up Client Restore on Server 2012 R2 Essentials
    http://www.mcbsys.com/techblog/2014/01/set-up-client-restore-on-server-2012-r2-essentials/
    Hope this helps.
    Best Regards,
    Andy Qi
    Andy Qi
    TechNet Community Support

  • How can I Create a Client Configuration File for RemoteApp and Desktop Connection with Server 2012?

    I have a working RDS RemoteApp site and looking to test out the feature in Windows 7 Control Panel\All Control Panel Items\RemoteApp and Desktop Connections
    I came across this link: Create a Client Configuration File for RemoteApp and Desktop Connection and I believe this is what I need to do first, but these instructions are for
    Server 2008, and I'm running 2012.
    Any suggestions or tips on how I can begin testing this with Server 2012?

    Hi,
    You can manually enter the path to the 2012 feed and it will connect and download the RemoteApps and Desktop connections.
    If you need a sample .wcx file I have posted one here a couple of times.  If you want I will look for it and post a link.
    -TP
    I tried adding my URL's below, these are sample links that work for me right now for when I log into the web page, but neither of these work.  And I'm not sure what I would need to do with or how to create a .wcx file.
    When I type in my URL of: https://connect.mydomain.org/RDWeb, I get redirected to: 
    https://connect.mydomain.org/RDWeb/Pages/en-US/login.aspx?ReturnUrl=/RDWeb/Pages/en-US/Default.aspx

  • I have windows server 2012 R2 and install active directory

    My question is I install active directory in windows server 2012 R2 and create Group Policy. ( These set-up is only for test)
    Have not registered domain only install active directory to test. 
    So the problem is when I created Group policy for my user and put software restriction policy but its affected to my administrator accounts too, No when I open VMware (install Virtual Machine windows XP) and start os then its shows you can not user this
    software as you restricted from installing software (Something like that don't know exact Error). I could not start installed Virtual Machine. 
    Please give me a solution for this.
    This is the setup for a test use only so their not big environment connect with my pc.
    Thanks in advance.
    Regards,
    Krunal

    Hi,
    The following article is talking about creating and managing Group Policy on a Windows Server 2012:
    http://www.thomas-krenn.com/en/wiki/Creating_and_managing_a_Group_Policy_on_a_Windows_2012_Server
    As Darren Blanchard mentioned, if you want to apply the GPO, you could link it to an OU that contain the computer or user.
    Group Policy Overview
    http://technet.microsoft.com/en-us/library/hh831791.aspx
    Please feel free to let us know if you need further assistance.
    Regards.
    Vivian Wang

  • Hyper-v Role in Windows Server 2012 foundation and Essentials

    Hello,
    I have seen that the two low cost version of Windows Server 2012 essential and Foundation) will not support hyper-v. Can you please tell me what it means exactly :
    Can you please tell me what is possible :
    -The server can not be installed as a hyper-v  guest (probably yes)
    -The hyper-v role can not be installed on the server (so I have to rely on vmware)?
    - Hyper-v role can be installed but there is no free license included with the server.
    Thank you
    Marc

    I suppose then, you would have to install Windows 8 and Hyper-V as your guest or core.
    Then run your Server 2012 Foundation under Win8.  which has 512GB Memory Limit.
    It seems asinine that you cannot install this role on Foundation, but seemingly you could work around it with Win8.  (Or Sun Virtual Box (free) (or VmWare(Free).
    So load up a dozen Win8Pro virutal sessions on that Win8 VirtualBox with up to 512GB Memory and Create your own Ghetto Remote Desktop Server with Foundation and Windows 8.   ;)
    What good is it if your can't run Hyper-V and Remote desktop services?  Those are the two apps small business need most.  But Microsoft strips it out, calls it a DEAL  (Essentials and Foundation) , yet if you want the good stuff, you're gonna
    have to buy Server 2012 Standard anyhow, + the CALs.
    So you are hooked into this "deal" by Microsoft Special Offer.   Its special alright, because you get to buy it twice.  The stripped down version that come with your server, then the full version when you discover Foundatoin and Essentials gives
    you AD, and thats it.  Nothing Else.  No "deal"
    Remember:
    All you get with Foundation or Essentials is AD and Group Policy.
    You cannot load RDP on Foundation or Essentials
    You cannot load Exchange on a DC, or Foundation or Essentials
    You cannot load Exchange and RDP on the same box.
    You cannot have Remote Web Apps if you load RDP on your DC.
    You cannot win with Microsoft.  No worthwhile "deal" has ever come out of the city of Redmond.
    The internet is a one-way money pipeline to Microsoft.
    Its three times the work, three times the cost and requires three servers licenses to do with 2012, what you could do with one 2008R2 license.  
    Might as well purchase 2 Server 2013 Standard Editions if you want:
    1.) Active Directory
    2.) Remote Desktop and Remote Apps
    3.) Your own Exchange Server
    You are better off installing a NAS if all you need is a file server. 
    Why bother with Foundation or Essentials?  Its a "Gimmick-ware"

Maybe you are looking for