Uninstall VIA RAID tool

I mistakenly installed the VIA RAID tool from Live Update - however I only have 1 SATA drive and do not intend to add further drives. The RAID tool now loads at windows start up and I cannot find any options to prevent this or even to unistall. Any ideas?

Just to conclude..
BIOS doesn't show RAID (at all.. KM4M-V) - I also disabled 2nd SATA drivebut as I suspected the VIA RAID Tool still loaded at start-up. I was unsure about removing SATA RAID driver from device drivers as apart from the offending tool loading at power up everything was working sweetly. So I installed Winpatrol and removed RAID Tool from start-up items.
Now I'm happy

Similar Messages

K8T NEO - MSI/Via Raid Tool useless

I am one of those unfortunate people who bought a K8T Neo FSR Motherboard (Mine has been replaced 3 times after failing totally but whose counting?). I am now having serious problems with my fourth version of this motherboard or at least I think I am. I am not sure!
Let me explain:
My SATA HDD Disk drives keep failing - or more correctly - I am getting messages from Windows Error Reporting that tells me there are disk problems. The exact error messages are reproduced below:
Event Type:   Error
Event Source:   viamraid
Event Category:   None
Event ID:     9
Date:      31/08/2006
Time:      8:32:41 PM
User:      N/A
Computer:   MASTER
Description: The device, \Device\Scsi\viamraid1, did not respond within the timeout period.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 0f 00 10 00 01 00 6a 00 ......j.
0008: 00 00 00 00 09 00 04 c0 .......À
0010: 00 01 00 00 00 00 00 00 ........
0018: 5b 09 00 00 00 00 00 00 [.......
0020: 00 00 00 00 00 00 00 00 ........
0028: 00 00 00 00 02 00 00 00 ........
0030: 00 00 00 00 07 00 00 00 ........
This is immediately followed by the following message:
Event Type:   Warning
Event Source:   Disk
Event Category:   None
Event ID:     51
Date:      31/08/2006
Time:      8:32:41 PM
User:      N/A
Computer:   MASTER
Description: An error was detected on device \Device\Harddisk2\D during a paging operation.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Data:
0000: 04 00 68 00 01 00 b6 00 ..h...¶.
0008: 00 00 00 00 33 00 04 80 ....3..
0010: 2d 01 00 00 00 00 00 00 -.......
0018: 00 00 00 00 00 00 00 00 ........
0020: 00 00 00 00 00 00 00 00 ........
0028: 57 87 00 00 00 00 00 00 W......
0030: ff ff ff ff 03 00 00 00 ÿÿÿÿ....
0038: 40 00 00 44 00 00 02 00 @..D....
0040: ff 20 0a 12 88 02 20 40 ÿ ... @
0048: 00 00 01 00 0a 00 00 00 ........
0050: 00 00 00 00 00 06 6c 84 ......l
0058: 00 00 00 00 60 36 62 86 ....`6b
0060: 00 00 00 00 f7 04 81 05 ....÷..
0068: 2a 00 05 81 04 f7 00 00 *...÷..
0070: 80 00 00 00 00 00 00 00 .......
0078: 00 00 00 00 00 00 00 00 ........
0080: 00 00 00 00 00 00 00 00 ........
0088: 00 00 00 00 00 00 00 00 ........
I started getting these messages from a brand new SATA HDD which I immediately replaced. All went well for a week or so and then I started getting the exact same error messages all over again!
Were both HDD's really defective? I am beginning to wonder!
The practical implication of the above errors is that my computer freezes totally - I can't do anything at all - no mouse - no keyboard - no saving work - nothing! When I reboot and run Scandisk /F /R I sometimes get some disk surface errors but mostly I don't.
To my way of thinking there are two possibilities:
(1) Both these disk drives have genuine technical problems (ie such as surface errors)
(2) The MSI/Via SATA disk controllers on the motherboard are faulty and this is causing disk errors or possibly even disk crashes (is this even possible? I don't know!)
After the bad run that I have already had with K8T NEO motherboards please forgive me for being suspicious that my HDD problems really could result from a faulty SATA/HDD/Controller rather than genuine disk errors.
To help resolve the issue I downloaded and installed MSI's latest SATA HDD disk drivers which includes the VIA RAID TOOL. The raid tool includes an option to "check the status of controllers and disk drives" and a system "log" which is supposed to record all error conditions/events that occur on devices it controls.
The main problem here is that *IT DOESN'T WORK* !!!
Just a short wile ago my system started acting strangely and then it froze again (third time this hour). I opened the MSI/VIA Raid Tool from the System Tray and checked the logs - There was nothing in them at all - and yet in Windows Error Reporting there were 5 distinct error conditions reported. Obviously the MSI/VIA Raid Tool doesn't work too well.
I am at a loss as to what to do next. Has anybody out there had similar problems?
What steps should I take to resolve these issues?
Any comments/suggestions?

Not sure how a scope can let you know if you are supplying enough amps. Ripple and noise are basically non issues as the voltages are further regulated on the MB before they get to the componant level.
Almost everything is now regulated from the 12v supply unlike past systems were. As Watts do not tell how much 12v is being supplied by the PSU it is a non starter when you desribe your PSU. You can have a PSU that is 500w and only provides 8a on the 12v rail. That will not even allow an A64 system to startup. As is said over and over again in the forum don't assume that a 500w PSU will ruin your Rig. 24 or more amps on the 12v rail is recommended for a small to mid size build now days. More may be needed as you add parts to your system.
As this is not a common problem on that board, and I should know as I built a fairly large rig from one... We need to have complete specs. Did you know that a high end ATi Vid Card can use more juice than many CPU's you can use on that board? See why this is a concern that we get all the specs?
Like Hans said though I won't bother asking again either. Without some idea what we are looking at all we are doing is looking into a crystal ball. We would like to see if we can help but working with a crystal ball isn't in the tech manual.

Problems starting GlassFish via GlassFish Tools

Hi everyone,
I am experiencing problems in starting a GlassFish Server (Open Source Edition 4.1 (build 13)) via GlassFish Tools in Eclipse Luna on my MacBook (OS X Yosemite) as described in these postings. The server is stuck at 69 % on starting up until a TimeoutException appears.
The problem can be solved though by going back to an older version of GlassFish tools (it seems 7.3.2.20141114 is the last version which is working for me).
On my Windows PC no such problems occur, even when running GlassFish tools in the latest version.
Is anyone experiencing similar issues and might provide a hint to fix this?
I really appreciate any help in this matter .
Thanks,
Erun

Hi Erun
I have exactly the same configuration and exactly same problem. Do you still remember how did you solve this problem?
kind regards
Aliye

VIA RAID Combo Diskette?

Ok, so I'm building a new SFF PC using a K8MM-V motherboard and a Western Digital SATA HD. I'm also using an external floppy drive to load the SATA drivers when prompted with F6. The disk that came with my motherboard did not work when loading these drivers, so I had to go and download the drivers and put them on a floppy disk of my own. When I get to the screen to load the drivers everything works fine. Windows goes on, loads its stuff, I hit F8, partition, etc. Problem is that after I partition the drive I am prompted to put the "VIA RAID Combo Diskette" in my floppy drive and press enter to continue before Windows goes on to setting up its files. I have no idea what this disk is. I tried the one that came with my motherboard and the one that I created, both yielding no luck. All that happens when I use those two disks is that I hit enter but nothing happens, like, the drive doesn't even try to access the floppy.
Anyone know what this disk is, or if I'm doing something wrong? Any help would be appreciated. Thanks.

Im having a similar problem.
I have Windows X64 bit edition with an Athlon 64 3200+
When I boot from the CD I press F6, it loads the drivers fine (that I downloaded from the MSI website http://www.msi.com.tw/program/support/driver/dvr/spt_dvr_detail.php?UID=574&kind=1 )
I then go through the other various steps and at the end when it begins to copy files (before the reboot) it asks for the VIA RAID Combo Diskette.
I try using the disk I already have - from MSI website.
I have also tried many times fiddling around with files and puting them onto the disk, from the X64 download from MSI.
No luck. Any help would be muchly appreciated

How to uninstall "Command Line Tools" in Xcode 4.3?

Just installed Command Line Tools using the perference in Xcode 4.3. After removing Xcode 4.3, I found the Command Line Tools are not removed.
Is there any way to uninstall?
Thanks!

Check the 'About Xcode' readme:
Uninstalling Xcode Developer Tools
To uninstall Xcode developer tools on the boot volume along with the <Xcode> directory, from a Terminal window type:
$ sudo <Xcode>/Library/uninstall-devtools --mode=all
To remove the underlying developer content on the boot volume, but leave the <Xcode> directory and supporting files untouched, from a Terminal window type:
$ sudo <Xcode>/Library/uninstall-devtools --mode=systemsupport
To just remove the UNIX development support on the boot volume, but leave the <Xcode> directory and supporting files untouched, from a Terminal window type:
$ sudo <Xcode>/Library/uninstall-devtools --mode=unixdev
Finally, to just uninstall the <Xcode> directory you can simply drag it to the trash, or from a Terminal window type:
$ sudo <Xcode>/Library/uninstall-devtools --mode=xcodedir
NOTE: The uninstaller that ships with previous versions of the Xcode developer tools will not clean everything off of your system properly. You should use the one installed with these Xcode developer tools.
-=-
If you find a black hole with the above, you could always reinstall Xcode, with those tools deselected and then delete according to the above, but all bets are off at that point, sorry
Good luck in any case.

I would like to clear my address row history completely, but I never get it totallly emptied. The remaining addresses are not bookmarked, i.e no stars on the row, but still exist after I have emptied all history both via the History link and via the Tools

I would like to clear my address row history completely, but I never get it totallly emptied. The remaining addresses are not bookmarked, i.e no stars on the row, but still exist after I have emptied all history both via the History link and via the Tools link. How come adresses still can exist after I have done this?
== This happened ==
Not sure how often

I clear all history but i still get hints (what i've typed before) when i wanna type something in a site i've visited before!! whats the solution?

Updating VIA RAID Bios on K8T Master-FAR 2

How do I update the VIA Raid bios that came with the v.220D SATA drivers?
I see the two rom files (6420R231.rom and 6420N231.rom) in the bios directory, but no directions on how to update the bios.
Tim

You don't. You have to wait for MSI to integrate any RAID BIOS improvements into a new BIOS release for the board.

MSI K8T NEO 2 VIA RAID & 2x120GB S-ATA Connection Problem

Hello,
I have 2x120GB S-ATA HDDs. I tried connect them to VIA Raid Controller (Raid 0), but Second HDD connected on S-ATA 2 is not detected .. I don't know why. I've connected them to Promis PDC 20579 and everything works fine. But now I wanna install Windows XP 64bit edition, and there are no 64bit dirvers for PDC20579, So I wanna connect it on VIA RAID, where drivers are available. Can anybody help me please ? (Can I lost my data if i reconnect from Promise to VIA ?)

I agree, but it seems that the VIA controller is more sensitive to it then the Promise one
Still, I think the entire SATA cable+connectors are poor design in total....rushed out the door so to speak....I wish they asked me....

Windows 10 upgrade asks to uninstall HP Security tools on Probook 4540s and finger reader gone

Recently Windows updated to Windows 10 version. Before upgrade it asks to uninstall HP security tools as it is not compatible on Windows 10. So after uninstall Windows 10 upgrade went fine. Now my finger scanner verfication option gone during login. Is there latest tool comptabile for Windows 10 available ?

I want to upgrade from windows7 to windows10 (probook 4350s) I have the same question about compatible version, which I hope HP or somebody answer soon and help us...I also cant uninstall my protect tools as upgrade needs me to.I want to know is it possible for finger scanner to work in windows10 after uninstalling HPPTM. thanks,Nazanin Mirzabeigi

Creating a Win7 OS install disc via recovery tools?

Is there any way to clean install Win7 (that is, nothing but the OS) from the Lenovo recovery discs I made via the ThinkVantage tool, or is it limited to a full factory-fresh restore only?
If that's the case, is it possible to create a Win7-only install disc from the recovery partition?
TIA

From what I know, you will need ImageUltra Builder tool installed to do this. The trial version can be downloaded from Lenovo/IBM website. TVT R&R OS installation files were created by this tool. The OEM/CTO build was prepared by Lenovo's ITC team.
However, if you want to do this yourself, I would recommend you to use a Microsoft tool called Windows7-USB-DVD-tool. This tool can automatically expand ISO OS installation file to USB flash memory cards or a DVD. More importantly, it's bootable. You can install WIN7 directly from USB flash memory or a backup DVD.
http://forums.lenovo.com/t5/Windows-7-Launch/Installing-windows-7-from-a-USB-Drive-Suitable-for-netb...

Contribute 4 upgrade via network tool Zenworks

We are preparing to upgrade a significant number of
Contribute 2 programs to Contribute 4. We would like to use an MSI
file and our “ZENworks” network tool (ZENworks is
similar to Microsoft’s SMS). We would like to know:
1. How to provide the requisite serial number for the
installations (we received all our copies on one CD).
2. How to respond to the “Import settings?”
question with a "No"
Any other experience or tips you can share would be greatly
appreciated.
On the verge of 4
Mark P.

Matt Adams wrote:
> We are distributing Contribute 3 via Zenworks, we didn't
use the msi
> integration, I just took a snapshot of the installation
using the
> Zenworks snapshot tool. I just made sure to stop the
snapshot after I
> put in our site license key, and answered no to
registering. So far we
> have given it to about 6 people, and none have had a
problem. I have
> not tried this on Contribute 4 though.
>
> Matt
>
> Mpolha wrote:
>> We are preparing to upgrade a significant number of
Contribute 2
>> programs to Contribute 4. We would like to use an
MSI file and our
>> ?ZENworks? network tool (ZENworks is similar to
Microsoft?s SMS). We
>> would like to know:
>> 1. How to provide the requisite serial number for
the
>> installations (we received all our copies on one
CD).
>> 2. How to respond to the ?Import settings?? question
with a "No"
>>
>> Any other experience or tips you can share would be
greatly appreciated.
>>
>> On the verge of 4
>> Mark P.
>>
>>
The msi file can be extracted from the setup exe using Winzip
a) Providing the serial number is not possible.
b) Import settings is an in-product feature, and the
installer plays no
part in this. Not possible again.

Promise RAID vs. Via RAID

When I was setting up my system I wasn't really sure which RAID controller I should use in order to get the best performance...I opted to go with the Via controller as it is an integrated part of the KT800 chipset whereas the Promise RAID controller is an optional add-in chip (or such is my understanding), so I figured using the Via controller would give the best performance...but I'm curious as to how the Promise controller performs. Has anyone tried setting an array up both ways and testing to see which controller performed better?
I'm running two 36 GB WD Raptor SATA drives in RAID-0 off the Via controller, and I get a score of 61 MB/sec in Sandra 2004's File System benchmark...if anyone is running a similar array off the Promise controller and could post their benchmark results, I'd appreciate it.

I've 'tested' both controllers.
Before the K8T, I was using a KT4 ultra with a Promise 376 and two raptors RAID0 (around 60-70Mb/s with HDTach)
Then I switched to the Promise 378 of the K8T (I keep promise to keep data). A little bit better than with the 376 of the KT4V but not very clear. I recently put the two raptors on the VIA. A little bit better but again, not very clear. It seems however that with the VIA the output is more 'unstable' .. I mean: with Promise, HD Tach gives me a straight line from the begining of the disk array to the end; with VIA, it's less straight.
I think I will crash my RAID 0 to test with one raptor on the VIA and one on the Promise. OSsystem for a disk, software and apps for the other one. I'm not sure that it's a goo idea

How do I uninstall the Google tool bar?

How do I uninstall google toolbar from Safari 5.1 OS X Lion.
I didn't down load the toolbar and I can not find any reference in Google about uninstalling or deleting this tool bar.

Hi thank you replying however, I'm not refering to the google search bar in the tool bar of Safari itself thei is a Black bar that runs under the "Book Marks Bar" it is below the Tabs when I am using them.
At the left side of the screen within the browser pan the Black Google Search Toolbar has my email address and a gear icon and on the right side of the black google search bar are seveal menu option running left to right that inclue "Web, Imagaes, Video,Maps Shopping, News, Gmail and More then a small drop down arrow with yet more options.
This is definitly an unwanted "after market" option!

CMR SIP alias via Productvity tools

Recently added CMR and running into an issue with SIP Alias for video endpoints. When scheduled via the Webex portal, the SIP alias is correct ([email protected]). However when we schedule using Productivity Tools or via Jabber, it schedules the meeting fine but then assigns the video alias differently. Rather than users firstname.lastname, it assigns the meeting number as the video alias. So now its [email protected] I need to figure out how to create a consistent meeting invite.

Hi,
So your current situation is that you are using AnyConnect with Split-tunneling? So you can access the LAN through VPN and Internet through the users local Internet connection?
I wonder if the problem with Full-Tunnel + Internet traffic is due to problem with NATing the traffic from VPN Client pool to the "outside" interface IP?
I think that NAT could be done by the following configuration
object network VPN-POOL
subnet 192.168.0.200 255.255.255.248
nat (outside,outside) after-auto source dynamic VPN-POOL interface
EDIT: The "after-auto" should take the rule at the bottom of the NAT rules, but I'm still thinking should it interfere with the configurations even if it didnt have the parameter.
I've only done this in software 8.2 and below, where it was
global (outside) 1 x.x.x.x
nat (inside) 1 10.10.10.0 255.255.255.0
nat (outside) 1 192.168.0.200 255.255.255.248
But as I said I havent done this with the new software. I can probably test this tomorrow at work though.
- Jouni
EDIT2:
I'm not 100% sure but is the following NAT statement even needed at the current configuration?
nat (inside,outside) source static any any destination static NETWORK_OBJ_192.168.0.200_29 NETWORK_OBJ_192.168.0.200_29
EDIT3:
I also usually use a totally different network for the VPN-pool. Your current LAN seems to be 192.168.0.0/24 and the VPN pool is 192.168.0.200/29. Maybe the top NAT statements are causing problems with the VPN Client Internet traffic.
What I would try to do is change the VPN Client pool to some different network, do the NAT0 between LAN and POOL like you have in the current configuration (just with new VPN Pool) and use the PAT configuration mentioned earlier. Leave out the NAT statement in the "EDIT2" in this post.
Sorry this is alot of guessing from my part before I get to test it myself with a lab ASA.

How do I delete or uninstall the winamp tool bar?

winamp tool bar showed up without my deliberate install of it. I want to uninstall it and have not been able to. When I click on the little gear icon located on the right side the drop down box says "uninstall winamp tool bar" when I click on it I go to the Add-on Manager and I cannot find any further option to delete it. Thanks for any assistance you can provide. Jan the Man!

See if this still works. <br />
http://forums.winamp.com/showthread.php?t=292427

Uninstall VIA RAID tool

Similar Messages

Maybe you are looking for