Uninstalled graphic card - now unit doesn't boot

I managed to uninstall my graphic card and when I restart my pc, the computer screen goes black and even though I go into safemode, it does not work. In SafeMode the screen is black except the blinking "_" in top left corner, Ive waited over 30 minutes on the "_" to continue, but in vain.
Please help me!

Hi
As far as I know this issue occurs because the unit cant boot.
Well, it could be possible that the HDD has a fault or the boot sector is damage.
You should try to boot from the CD and if it possible so you should recover the unit with the delivered recovery CD

Similar Messages

Changed graphics cards, now doesn't detect monitors

*I changed graphics cards on a Mac Pro and now its not detecting the monitors despite booting OSX10.5!*
Mac Pro
2 Monitors
Replacing radeon card with a geforce 7300gt
Unplugged everything
replaced card
Plugged everything back in, power last.
Powered on
Monitors are blank (cannot detect signal, autocycling between analog/dvi searching for one)
I've tried plugging just one monitor in and just a mouse/keyboard.
I've tried reseating the card.
I've tried plugging the card into 16x slot #2.
*Whats so infuriating about this is the computer actual BOOTS!* The keyboard dvd eject button responds, and I can explore the contents of this Mac Pros hard drive through the local network.
Any ideas?
What am I doing wrong! ><

What is the video card you are installing? Is this an ATI 3870? If so did you read the installation instructions before installing? You were to install the software drivers before installing the card.
Also check that you got the Mac version of this card.
Message was edited by: Kappy

Created new Apple ID, redeemed $20 gift card, now Apple doesn't recognise my Apple ID and the $20 Gift Card says it has been redeemed when it has just disappeared into my Apple ID that can't be found. I'm going around in circles trying to find my $20 gift

I was given a $20 iTunes Gift Card for my birthday, I setup a new Apple ID, redeemed my card and now Apple doesn't recognise my Apple ID and the $20 credit has disappeared. I've logged on using my Dad's Apple ID, but where has the $20 Gift Card gone? I try to redeem it again and get message that it has already been redeemed. Not impressed with Apple at all. I've sent 2 emails to their support, no response. I tried calling today and the call centre is closed.
Can anyone help me sort out this crazy problem? Why does Apple make it so hard to sort out?

Hi thanks, When I enter the Apple ID I get a message that either my Apple ID or password are incorrect. I then go to Forgotten Password, enter my Apple ID, choose to get an email to reset the password, but no email arrives.
So if I can't find/reuse the Redeemed Gift Card due to the Apple ID problem, surely that doesn't mean I lose $20??
I first emailed one week ago. Have emailed for the third time today.

Graphic card driver update doesn't work for Windows 8.1 upgrade (Ideapad Y500)

I upgraded my windows 8 to Windows 8.1 today and it probably is a huge mistake. After the upgrade my Ideapad Y500 started to look weird (Firefox stopped working). I searched around for solution and was told that I probably need to upgrade the driver to my graphic card. So I went to the driver download page and downloaded the NVIDIA GeForce GT750M Second VGA BIOS Update for Windows 8.1
I followed the instruction to run the "Winflash_Yx00s.bat" file, but after I seleted "yes" to let it modify the system, there is a very fast flashing a little black window (too fast for me to see what it is), and nothing happens afterwards. I checked to make sure that nothing is running in the background. After waited for half an hour I tried to restart the computer and still nothing happens. The display still looks weird.
Please help me!

when I read posts like yours I often do the test myself
so I went into skype both metro and desktop skype and to my horror like you I did not have the option only my logitech webcam was an option
I went into devices and see that ht had FaceTimeHD camera (Built-in) as malfunctioning not working devices there
I went to my bootcamp driver zip and ran the apple AppleCamera64.exe
but little did it help then I googled it
https://www.google.dk/search?q=bootcamp+facetime+hd+camera+driver&oq=bootcamp+fa cetime+hd+camera+&aqs=chrome.1.69i57j0.9286j0j8&sourceid=chrome&es_sm=93&ie=UTF- 8
came across this post at ms
http://answers.microsoft.com/en-us/windows/forum/windows_8-hardware/facetime-hd- camera/0ef43e8a-45bc-4797-99f7-c57848b9f2bb
did the uninstall of both of the unknown devices as suggested and ran a scan for new hardware and bam!
the camera was back in action
suppose looking like a gobling shark made it so I never noticed that win8.1 had broken my facetime cam before you brought it up

Why graphics card on Windows7 doesn't work like Mac OS?

I have broplem with graphics card on my Macbook Pro mid 2012. When I run Design Application on Mac OS It run very good graphics, but when I run it on bootcamp WINDOWS 7 it work so bad, could you please tell me about this ? And why Dedicated Video Memory show only 64MB on WINDOW 7 but MAC OS 512MB? Sorry for my bad English. Thank in advance.

Running Windows in a VM has nothing to do with running Windows in a Boot Camp partition on the Native hardware.
Your VM problem is in no way related as the VM software Virtual Machine controls what and how the graphics system works. It does not address the real native graphics hardware.
Yes if anyone Needs to Use Windows as there main OS it would be best to buy a Real Windows PC as Apple still limits what you can do in Windows and the hardware it uses on the Mac when installed in a BC partition.

ATI Graphics card not detected on cold boot, works on warm boot

Hi All,
I hope you can help me out with this.
I'm using Radeon HD7850 with ATI-Catalyst.
The issue is, if I do a cold boot (physically turn off the power, turn back on) the system won't boot into X, only tty.
At this point, a reboot works fine.
Or if I don't turn off the power, just shutdown and reboot (warm boot), it works ok.
Here's the Xorg log on cold boot:
[ 2.226]
X.Org X Server 1.12.4
Release Date: 2012-08-27
[ 2.226] X Protocol Version 11, Revision 0
[ 2.226] Build Operating System: Linux 3.4.8-1-ARCH x86_64
[ 2.226] Current Operating System: Linux dmanPC 3.5.3-1-ARCH #1 SMP PREEMPT Sun Aug 26 09:14:51 CEST 2012 x86_64
[ 2.226] Kernel command line: BOOT_IMAGE=/vmlinuz-linux root=UUID=3766a71b-dbfe-4cc2-b7bd-948878b5da67 ro nomodeset quiet
[ 2.226] Build Date: 27 August 2012 08:04:39AM
[ 2.226]
[ 2.226] Current version of pixman: 0.26.2
[ 2.226] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 2.226] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 2.226] (==) Log file: "/var/log/Xorg.0.log", Time: Fri Sep 28 05:57:41 2012
[ 2.227] (==) Using config file: "/etc/X11/xorg.conf"
[ 2.228] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 2.228] (==) ServerLayout "aticonfig Layout"
[ 2.228] (**) |-->Screen "aticonfig-Screen[0]-0" (0)
[ 2.228] (**) | |-->Monitor "aticonfig-Monitor[0]-0"
[ 2.229] (**) | |-->Device "aticonfig-Device[0]-0"
[ 2.229] (==) Automatically adding devices
[ 2.229] (==) Automatically enabling devices
[ 2.231] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
[ 2.231] Entry deleted from font path.
[ 2.231] (WW) The directory "/usr/share/fonts/Type1/" does not exist.
[ 2.231] Entry deleted from font path.
[ 2.231] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/100dpi/".
[ 2.231] Entry deleted from font path.
[ 2.231] (Run 'mkfontdir' on "/usr/share/fonts/100dpi/").
[ 2.232] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/75dpi/".
[ 2.232] Entry deleted from font path.
[ 2.232] (Run 'mkfontdir' on "/usr/share/fonts/75dpi/").
[ 2.232] (==) FontPath set to:
/usr/share/fonts/misc/,
/usr/share/fonts/TTF/
[ 2.232] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 2.232] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 2.232] (II) Loader magic: 0x7c8b00
[ 2.232] (II) Module ABI versions:
[ 2.232] X.Org ANSI C Emulation: 0.4
[ 2.232] X.Org Video Driver: 12.1
[ 2.232] X.Org XInput driver : 16.0
[ 2.232] X.Org Server Extension : 6.0
[ 2.232] (--) PCI:*(0:7:0:0) 1002:6819:1462:2730 rev 0, Mem @ 0xe0000000/268435456, 0xf7b00000/262144, I/O @ 0x0000c000/256, BIOS @ 0x????????/131072
[ 2.232] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 2.232] (II) "extmod" will be loaded by default.
[ 2.232] (II) "dbe" will be loaded by default.
[ 2.232] (II) "glx" will be loaded by default.
[ 2.232] (II) "record" will be loaded by default.
[ 2.232] (II) "dri" will be loaded by default.
[ 2.232] (II) "dri2" will be loaded by default.
[ 2.232] (II) LoadModule: "extmod"
[ 2.233] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
[ 2.233] (II) Module extmod: vendor="X.Org Foundation"
[ 2.233] compiled for 1.12.4, module version = 1.0.0
[ 2.233] Module class: X.Org Server Extension
[ 2.233] ABI class: X.Org Server Extension, version 6.0
[ 2.233] (II) Loading extension MIT-SCREEN-SAVER
[ 2.233] (II) Loading extension XFree86-VidModeExtension
[ 2.233] (II) Loading extension XFree86-DGA
[ 2.233] (II) Loading extension DPMS
[ 2.233] (II) Loading extension XVideo
[ 2.233] (II) Loading extension XVideo-MotionCompensation
[ 2.233] (II) Loading extension X-Resource
[ 2.233] (II) LoadModule: "dbe"
[ 2.233] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
[ 2.234] (II) Module dbe: vendor="X.Org Foundation"
[ 2.234] compiled for 1.12.4, module version = 1.0.0
[ 2.234] Module class: X.Org Server Extension
[ 2.234] ABI class: X.Org Server Extension, version 6.0
[ 2.234] (II) Loading extension DOUBLE-BUFFER
[ 2.234] (II) LoadModule: "glx"
[ 2.234] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 2.236] (II) Module glx: vendor="Advanced Micro Devices, Inc."
[ 2.236] compiled for 6.9.0, module version = 1.0.0
[ 2.236] (II) Loading extension GLX
[ 2.236] (II) LoadModule: "record"
[ 2.236] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
[ 2.237] (II) Module record: vendor="X.Org Foundation"
[ 2.237] compiled for 1.12.4, module version = 1.13.0
[ 2.237] Module class: X.Org Server Extension
[ 2.237] ABI class: X.Org Server Extension, version 6.0
[ 2.237] (II) Loading extension RECORD
[ 2.237] (II) LoadModule: "dri"
[ 2.237] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
[ 2.237] (II) Module dri: vendor="X.Org Foundation"
[ 2.237] compiled for 1.12.4, module version = 1.0.0
[ 2.237] ABI class: X.Org Server Extension, version 6.0
[ 2.237] (II) Loading extension XFree86-DRI
[ 2.237] (II) LoadModule: "dri2"
[ 2.238] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
[ 2.238] (II) Module dri2: vendor="X.Org Foundation"
[ 2.238] compiled for 1.12.4, module version = 1.2.0
[ 2.238] ABI class: X.Org Server Extension, version 6.0
[ 2.238] (II) Loading extension DRI2
[ 2.238] (II) LoadModule: "fglrx"
[ 2.238] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
[ 2.262] (II) Module fglrx: vendor="FireGL - AMD Technologies Inc."
[ 2.262] compiled for 1.4.99.906, module version = 8.98.2
[ 2.262] Module class: X.Org Video Driver
[ 2.262] (II) Loading sub module "fglrxdrm"
[ 2.262] (II) LoadModule: "fglrxdrm"
[ 2.262] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 2.263] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 2.263] compiled for 1.4.99.906, module version = 8.98.2
[ 2.263] (II) AMD Proprietary Linux Driver Version Identifier:8.98.2
[ 2.263] (II) AMD Proprietary Linux Driver Release Identifier: 8.982
[ 2.263] (II) AMD Proprietary Linux Driver Build Date: Jul 27 2012 20:37:56
[ 2.263] (++) using VT number 8
[ 2.264] (WW) Falling back to old probe method for fglrx
[ 2.269] (II) Loading PCS database from /etc/ati/amdpcsdb
[ 2.271] (WW) fglrx: No matching Device section for instance (BusID ) found
[ 2.271] (EE) No devices detected.
[ 2.271]
Fatal server error:
[ 2.271] no screens found
[ 2.271]
Please consult the The X.Org Foundation support
at http://wiki.x.org
for help.
[ 2.271] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
[ 2.271]
Here's the same log for warm boot:
[ 2.289] (++) using VT number 8
[ 2.290] (WW) Falling back to old probe method for fglrx
[ 2.295] (II) Loading PCS database from /etc/ati/amdpcsdb
[ 2.296] (--) Chipset Supported AMD Graphics Processor (0x6819) found
[ 2.296] (WW) fglrx: No matching Device section for instance (BusID PCI:0@6:0:1) found
[ 2.297] (II) AMD Video driver is running on a device belonging to a group targeted for this release
[ 2.297] (II) AMD Video driver is signed
[ 2.297] (II) fglrx(0): pEnt->device->identifier=0x82b7a0
[ 2.297] (II) fglrx(0): === [xdl_xs112_atiddxPreInit] === begin
[ 2.297] (II) Loading sub module "vgahw"
[ 2.297] (II) LoadModule: "vgahw"
[ 2.298] (II) Loading /usr/lib/xorg/modules/libvgahw.so
[ 2.298] (II) Module vgahw: vendor="X.Org Foundation"
[ 2.298] compiled for 1.12.4, module version = 0.1.0
[ 2.298] ABI class: X.Org Video Driver, version 12.1
[ 2.298] (**) fglrx(0): Depth 24, (--) framebuffer bpp 32
[ 2.298] (II) fglrx(0): Pixel depth = 24 bits stored in 4 bytes (32 bpp pixmaps)
[ 2.298] (==) fglrx(0): Default visual is TrueColor
[ 2.298] (**) fglrx(0): Option "OpenGLOverlay" "0"
[ 2.298] (**) fglrx(0): Option "DPMS" "true"
[ 2.298] (==) fglrx(0): RGB weight 888
[ 2.298] (II) fglrx(0): Using 8 bits per RGB
[ 2.298] (==) fglrx(0): Buffer Tiling is ON
[ 2.299] (II) Loading sub module "fglrxdrm"
[ 2.299] (II) LoadModule: "fglrxdrm"
[ 2.299] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
[ 2.299] (II) Module fglrxdrm: vendor="FireGL - AMD Technologies Inc."
[ 2.299] compiled for 1.4.99.906, module version = 8.98.2
[ 2.299] ukiDynamicMajor: found major device number 251
[ 2.299] ukiDynamicMajor: found major device number 251
[ 2.299] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.299] ukiOpenDevice: node name is /dev/ati/card0
[ 2.299] ukiOpenDevice: open result is 11, (OK)
[ 2.299] ukiOpenByBusid: ukiOpenMinor returns 11
[ 2.299] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.299] (**) fglrx(0): NoAccel = NO
[ 2.299] (**) fglrx(0): AMD 2D Acceleration Architecture enabled
[ 2.299] (--) fglrx(0): Chipset: "AMD Radeon HD 7800 Series " (Chipset = 0x6819)
[ 2.299] (--) fglrx(0): (PciSubVendor = 0x1462, PciSubDevice = 0x2730)
[ 2.299] (==) fglrx(0): board vendor info: third party graphics adapter - NOT original AMD
[ 2.299] (--) fglrx(0): Linear framebuffer (phys) at 0xe0000000
[ 2.299] (--) fglrx(0): MMIO registers at 0xf7c00000
[ 2.299] (--) fglrx(0): I/O port at 0x0000c000
[ 2.299] (==) fglrx(0): ROM-BIOS at 0x000c0000
[ 2.300] (II) fglrx(0): AC Adapter is used
[ 2.303] (II) fglrx(0): Primary V_BIOS segment is: 0xc000
[ 2.303] (II) Loading sub module "vbe"
[ 2.303] (II) LoadModule: "vbe"
[ 2.303] (II) Loading /usr/lib/xorg/modules/libvbe.so
[ 2.304] (II) Module vbe: vendor="X.Org Foundation"
[ 2.304] compiled for 1.12.4, module version = 1.1.0
[ 2.304] ABI class: X.Org Video Driver, version 12.1
[ 2.304] (II) fglrx(0): VESA BIOS detected
[ 2.304] (II) fglrx(0): VESA VBE Version 3.0
[ 2.304] (II) fglrx(0): VESA VBE Total Mem: 16384 kB
[ 2.304] (II) fglrx(0): VESA VBE OEM: AMD ATOMBIOS
[ 2.304] (II) fglrx(0): VESA VBE OEM Software Rev: 15.17
[ 2.304] (II) fglrx(0): VESA VBE OEM Vendor: (C) 1988-2010, Advanced Micro Devices, Inc.
[ 2.304] (II) fglrx(0): VESA VBE OEM Product: PITCAIRN
[ 2.304] (II) fglrx(0): VESA VBE OEM Product Rev: 01.00
[ 2.309] (II) fglrx(0): AMD Video BIOS revision 9 or later detected
[ 2.309] (--) fglrx(0): Video RAM: 2097152 kByte, Type: GDDR5
[ 2.309] (II) fglrx(0): PCIE card detected
[ 2.309] (--) fglrx(0): Using per-process page tables (PPPT) as GART.
[ 2.309] (WW) fglrx(0): board is an unknown third party board, chipset is supported
[ 2.311] (II) fglrx(0): Using adapter: 6:0.0.
[ 2.320] (II) fglrx(0): [FB] MC range(MCFBBase = 0xf400000000, MCFBSize = 0x80000000)
[ 2.458] (II) fglrx(0): Interrupt handler installed at IRQ 48.
[ 2.458] (II) fglrx(0): RandR 1.2 support is enabled!
[ 2.458] (II) fglrx(0): RandR 1.2 rotation support is enabled!
[ 2.458] (==) fglrx(0): Center Mode is disabled
[ 2.458] (II) Loading sub module "fb"
[ 2.458] (II) LoadModule: "fb"
[ 2.458] (II) Loading /usr/lib/xorg/modules/libfb.so
[ 2.461] (II) Module fb: vendor="X.Org Foundation"
[ 2.461] compiled for 1.12.4, module version = 1.0.0
[ 2.461] ABI class: X.Org ANSI C Emulation, version 0.4
[ 2.461] (II) Loading sub module "ddc"
[ 2.461] (II) LoadModule: "ddc"
[ 2.461] (II) Module "ddc" already built-in
[ 2.571] (II) fglrx(0): Finished Initialize PPLIB!
[ 2.577] (II) fglrx(0): Output DFP1 using monitor section aticonfig-Monitor[0]-0
[ 2.577] (II) fglrx(0): Output DFP2 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP3 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP4 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP5 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP6 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP7 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP8 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP9 has no monitor section
[ 2.577] (II) fglrx(0): Output DFP10 has no monitor section
[ 2.577] (II) fglrx(0): Output CRT1 has no monitor section
[ 2.578] (II) Loading sub module "ddc"
[ 2.578] (II) LoadModule: "ddc"
[ 2.578] (II) Module "ddc" already built-in
[ 2.578] (II) fglrx(0): Connected Display0: DFP10
[ 2.578] (II) fglrx(0): Display0 EDID data ---------------------------
[ 2.578] (II) fglrx(0): Manufacturer: SAM Model: 524 Serial#: 1280455218
[ 2.578] (II) fglrx(0): Year: 2009 Week: 20
[ 2.578] (II) fglrx(0): EDID Version: 1.3
[ 2.578] (II) fglrx(0): Digital Display Input
[ 2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 2.578] (II) fglrx(0): Gamma: 2.20
[ 2.578] (II) fglrx(0): DPMS capabilities: Off
[ 2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2.578] (II) fglrx(0): First detailed timing is preferred mode
[ 2.578] (II) fglrx(0): redX: 0.648 redY: 0.339 greenX: 0.143 greenY: 0.070
[ 2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603 whiteX: 0.312 whiteY: 0.329
[ 2.578] (II) fglrx(0): Supported established timings:
[ 2.578] (II) fglrx(0): 640x480@60Hz
[ 2.578] (II) fglrx(0): 800x600@56Hz
[ 2.578] (II) fglrx(0): 800x600@60Hz
[ 2.578] (II) fglrx(0): 1024x768@60Hz
[ 2.578] (II) fglrx(0): Manufacturer's mask: 0
[ 2.578] (II) fglrx(0): Supported standard timings:
[ 2.578] (II) fglrx(0): #0: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 2.578] (II) fglrx(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2.578] (II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2.578] (II) fglrx(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2.578] (II) fglrx(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 2.578] (II) fglrx(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[ 2.578] (II) fglrx(0): Monitor name: SyncMaster
[ 2.578] (II) fglrx(0): Serial No: HMBS500385
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[ 2.578] (II) fglrx(0): EDID (in hex):
[ 2.578] (II) fglrx(0): 00ffffffffffff004c2d24053232524c
[ 2.578] (II) fglrx(0): 1413010380301b782a3851a656241248
[ 2.578] (II) fglrx(0): 9a50542308008100814081809500a940
[ 2.578] (II) fglrx(0): b30001010101023a801871382d40582c
[ 2.578] (II) fglrx(0): 4500dd0c1100001e000000fd00383c1e
[ 2.578] (II) fglrx(0): 5111000a202020202020000000fc0053
[ 2.578] (II) fglrx(0): 796e634d61737465720a2020000000ff
[ 2.578] (II) fglrx(0): 00484d42533530303338350a20200168
[ 2.578] (II) fglrx(0): End of Display0 EDID data --------------------
[ 2.578] (II) fglrx(0): EDID for output DFP1
[ 2.578] (II) fglrx(0): EDID for output DFP2
[ 2.578] (II) fglrx(0): EDID for output DFP3
[ 2.578] (II) fglrx(0): EDID for output DFP4
[ 2.578] (II) fglrx(0): EDID for output DFP5
[ 2.578] (II) fglrx(0): EDID for output DFP6
[ 2.578] (II) fglrx(0): EDID for output DFP7
[ 2.578] (II) fglrx(0): EDID for output DFP8
[ 2.578] (II) fglrx(0): EDID for output DFP9
[ 2.578] (II) fglrx(0): EDID for output DFP10
[ 2.578] (II) fglrx(0): Manufacturer: SAM Model: 524 Serial#: 1280455218
[ 2.578] (II) fglrx(0): Year: 2009 Week: 20
[ 2.578] (II) fglrx(0): EDID Version: 1.3
[ 2.578] (II) fglrx(0): Digital Display Input
[ 2.578] (II) fglrx(0): Max Image Size [cm]: horiz.: 48 vert.: 27
[ 2.578] (II) fglrx(0): Gamma: 2.20
[ 2.578] (II) fglrx(0): DPMS capabilities: Off
[ 2.578] (II) fglrx(0): Supported color encodings: RGB 4:4:4 YCrCb 4:4:4
[ 2.578] (II) fglrx(0): First detailed timing is preferred mode
[ 2.578] (II) fglrx(0): redX: 0.648 redY: 0.339 greenX: 0.143 greenY: 0.070
[ 2.578] (II) fglrx(0): blueX: 0.282 blueY: 0.603 whiteX: 0.312 whiteY: 0.329
[ 2.578] (II) fglrx(0): Supported established timings:
[ 2.578] (II) fglrx(0): 640x480@60Hz
[ 2.578] (II) fglrx(0): 800x600@56Hz
[ 2.578] (II) fglrx(0): 800x600@60Hz
[ 2.578] (II) fglrx(0): 1024x768@60Hz
[ 2.578] (II) fglrx(0): Manufacturer's mask: 0
[ 2.578] (II) fglrx(0): Supported standard timings:
[ 2.578] (II) fglrx(0): #0: hsize: 1280 vsize 800 refresh: 60 vid: 129
[ 2.578] (II) fglrx(0): #1: hsize: 1280 vsize 960 refresh: 60 vid: 16513
[ 2.578] (II) fglrx(0): #2: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
[ 2.578] (II) fglrx(0): #3: hsize: 1440 vsize 900 refresh: 60 vid: 149
[ 2.578] (II) fglrx(0): #4: hsize: 1600 vsize 1200 refresh: 60 vid: 16553
[ 2.578] (II) fglrx(0): #5: hsize: 1680 vsize 1050 refresh: 60 vid: 179
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2008 h_sync_end 2052 h_blank_end 2200 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Ranges: V min: 56 V max: 60 Hz, H min: 30 H max: 81 kHz, PixClock max 175 MHz
[ 2.578] (II) fglrx(0): Monitor name: SyncMaster
[ 2.578] (II) fglrx(0): Serial No: HMBS500385
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 148.5 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1920 h_sync: 2448 h_sync_end 2492 h_blank_end 2640 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 1080 v_sync: 1084 v_sync_end 1089 v_blanking: 1125 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1390 h_sync_end 1430 h_blank_end 1650 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 74.2 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 1280 h_sync: 1720 h_sync_end 1760 h_blank_end 1980 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 720 v_sync: 725 v_sync_end 730 v_blanking: 750 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 732 h_sync_end 796 h_blank_end 864 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 576 v_sync: 581 v_sync_end 586 v_blanking: 625 v_border: 0
[ 2.578] (II) fglrx(0): Supported detailed timing:
[ 2.578] (II) fglrx(0): clock: 27.0 MHz Image Size: 477 x 268 mm
[ 2.578] (II) fglrx(0): h_active: 720 h_sync: 736 h_sync_end 798 h_blank_end 858 h_border: 0
[ 2.578] (II) fglrx(0): v_active: 480 v_sync: 489 v_sync_end 495 v_blanking: 525 v_border: 0
[ 2.578] (II) fglrx(0): Number of EDID sections to follow: 1
[ 2.578] (II) fglrx(0): EDID (in hex):
[ 2.578] (II) fglrx(0): 00ffffffffffff004c2d24053232524c
[ 2.578] (II) fglrx(0): 1413010380301b782a3851a656241248
[ 2.578] (II) fglrx(0): 9a50542308008100814081809500a940
[ 2.578] (II) fglrx(0): b30001010101023a801871382d40582c
[ 2.578] (II) fglrx(0): 4500dd0c1100001e000000fd00383c1e
[ 2.578] (II) fglrx(0): 5111000a202020202020000000fc0053
[ 2.578] (II) fglrx(0): 796e634d61737465720a2020000000ff
[ 2.578] (II) fglrx(0): 00484d42533530303338350a20200168
[ 2.579] (II) fglrx(0): Printing probed modes for output DFP10
[ 2.579] (II) fglrx(0): Modeline "1920x1080"x60.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "1920x1080"x50.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x1200"x60.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1776x1000"x50.0 148.50 1776 2304 2348 2640 1000 1004 1009 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1680x1050"x50.0 148.50 1680 2448 2492 2640 1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1680x1050"x60.0 146.25 1680 1784 1960 2240 1050 1053 1059 1089 -hsync +vsync (65.3 kHz)
[ 2.579] (II) fglrx(0): Modeline "1400x1050"x60.0 162.00 1400 1664 1856 2160 1050 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1400x1050"x50.0 148.50 1400 2448 2492 2640 1050 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x900"x60.0 162.00 1600 1664 1856 2160 900 1201 1204 1250 +hsync +vsync (75.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1600x900"x50.0 148.50 1600 2448 2492 2640 900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x1024"x50.0 148.50 1280 2448 2492 2640 1024 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x1024"x60.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1440x900"x50.0 148.50 1440 2448 2492 2640 900 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1440x900"x60.0 106.50 1440 1520 1672 1904 900 903 909 934 -hsync +vsync (55.9 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x960"x50.0 148.50 1280 2448 2492 2640 960 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x960"x60.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x800"x50.0 148.50 1280 2448 2492 2640 800 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x800"x60.0 83.50 1280 1352 1480 1680 800 803 809 831 -hsync +vsync (49.7 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x768"x50.0 148.50 1280 2448 2492 2640 768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x768"x60.0 83.50 1280 1352 1480 1680 768 803 809 831 -hsync +vsync (49.7 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x720"x60.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz)
[ 2.579] (II) fglrx(0): Modeline "1280x720"x50.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "1024x768"x50.0 148.50 1024 2448 2492 2640 768 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz)
[ 2.579] (II) fglrx(0): Modeline "1152x648"x50.0 74.25 1152 1592 1632 1980 648 653 658 750 +hsync +vsync (37.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x50.0 148.50 800 2448 2492 2640 600 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x60.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz)
[ 2.579] (II) fglrx(0): Modeline "800x600"x56.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x576"x60.0 148.50 720 2008 2052 2200 576 1084 1089 1125 +hsync +vsync (67.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x576"x50.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x480"x50.0 148.50 720 2448 2492 2640 480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "720x480"x59.9 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz)
[ 2.579] (II) fglrx(0): Modeline "640x480"x50.0 148.50 640 2448 2492 2640 480 1084 1089 1125 +hsync +vsync (56.2 kHz)
[ 2.579] (II) fglrx(0): Modeline "640x480"x60.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz)
[ 2.579] (II) fglrx(0): EDID for output CRT1
[ 2.579] (II) fglrx(0): Output DFP1 disconnected
[ 2.579] (II) fglrx(0): Output DFP2 disconnected
[ 2.579] (II) fglrx(0): Output DFP3 disconnected
[ 2.579] (II) fglrx(0): Output DFP4 disconnected
[ 2.579] (II) fglrx(0): Output DFP5 disconnected
[ 2.579] (II) fglrx(0): Output DFP6 disconnected
[ 2.579] (II) fglrx(0): Output DFP7 disconnected
[ 2.579] (II) fglrx(0): Output DFP8 disconnected
[ 2.579] (II) fglrx(0): Output DFP9 disconnected
[ 2.579] (II) fglrx(0): Output DFP10 connected
[ 2.579] (II) fglrx(0): Output CRT1 disconnected
[ 2.579] (II) fglrx(0): Using exact sizes for initial modes
[ 2.579] (II) fglrx(0): Output DFP10 using initial mode 1920x1080
[ 2.579] (II) fglrx(0): DPI set to (96, 96)
[ 2.579] (II) fglrx(0): Eyefinity capable adapter detected.
[ 2.579] (II) fglrx(0): Adapter AMD Radeon HD 7800 Series has 6 configurable heads and 1 displays connected.
[ 2.579] (==) fglrx(0): PseudoColor visuals disabled
[ 2.579] (II) Loading sub module "ramdac"
[ 2.579] (II) LoadModule: "ramdac"
[ 2.579] (II) Module "ramdac" already built-in
[ 2.579] (==) fglrx(0): NoDRI = NO
[ 2.579] (==) fglrx(0): Capabilities: 0x00000000
[ 2.579] (==) fglrx(0): CapabilitiesEx: 0x00000000
[ 2.579] (==) fglrx(0): OpenGL ClientDriverName: "fglrx_dri.so"
[ 2.579] (==) fglrx(0): UseFastTLS=0
[ 2.579] (II) fglrx(0): Desktop Vsync is enabled.
[ 2.579] (--) Depth 24 pixmap format is 32 bpp
[ 2.579] (II) Loading extension ATIFGLRXDRI
[ 2.579] (II) fglrx(0): doing swlDriScreenInit
[ 2.579] (II) fglrx(0): swlDriScreenInit for fglrx driver
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiDynamicMajor: found major device number 251
[ 2.579] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.579] ukiOpenDevice: node name is /dev/ati/card0
[ 2.579] ukiOpenDevice: open result is 12, (OK)
[ 2.579] ukiOpenByBusid: ukiOpenMinor returns 12
[ 2.579] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.579] (II) fglrx(0): [uki] DRM interface version 1.0
[ 2.579] (II) fglrx(0): [uki] created "fglrx" driver at busid "PCI:6:0:0"
[ 2.579] (II) fglrx(0): [uki] added 8192 byte SAREA at 0x2000
[ 2.579] (II) fglrx(0): [uki] mapped SAREA 0x2000 to 0x7f1426d74000
[ 2.579] (II) fglrx(0): [uki] framebuffer handle = 0x3000
[ 2.579] (II) fglrx(0): [uki] added 1 reserved context for kernel
[ 2.579] (II) fglrx(0): swlDriScreenInit done
[ 2.579] (II) fglrx(0): Kernel Module Version Information:
[ 2.579] (II) fglrx(0): Name: fglrx
[ 2.579] (II) fglrx(0): Version: 8.98.2
[ 2.579] (II) fglrx(0): Date: Jul 27 2012
[ 2.579] (II) fglrx(0): Desc: AMD FireGL DRM kernel module
[ 2.579] (II) fglrx(0): Kernel Module version matches driver.
[ 2.579] (II) fglrx(0): Kernel Module Build Time Information:
[ 2.579] (II) fglrx(0): Build-Kernel UTS_RELEASE: 3.5.3-1-ARCH
[ 2.579] (II) fglrx(0): Build-Kernel MODVERSIONS: no
[ 2.579] (II) fglrx(0): Build-Kernel __SMP__: no
[ 2.579] (II) fglrx(0): Build-Kernel PAGE_SIZE: 0x1000
[ 2.579] (II) fglrx(0): [uki] register handle = 0x00004000
[ 2.589] (II) fglrx(0): DRI initialization successfull
[ 2.590] (II) fglrx(0): FBADPhys: 0xf400000000 FBMappedSize: 0x010e0000
[ 2.591] (==) fglrx(0): Backing store disabled
[ 2.591] (II) Loading extension FGLRXEXTENSION
[ 2.591] (**) fglrx(0): DPMS enabled
[ 2.591] (II) fglrx(0): Initialized in-driver Xinerama extension
[ 2.591] (**) fglrx(0): Textured Video is enabled.
[ 2.591] (II) LoadModule: "glesx"
[ 2.591] (II) Loading /usr/lib/xorg/modules/glesx.so
[ 2.601] (II) Module glesx: vendor="X.Org Foundation"
[ 2.601] compiled for 1.4.99.906, module version = 1.0.0
[ 2.601] (II) Loading extension GLESX
[ 2.601] (II) fglrx(0): GLESX enableFlags = 592
[ 2.602] (II) fglrx(0): GLESX is enabled
[ 2.602] (II) LoadModule: "amdxmm"
[ 2.602] (II) Loading /usr/lib/xorg/modules/amdxmm.so
[ 2.603] (II) Module amdxmm: vendor="X.Org Foundation"
[ 2.603] compiled for 1.4.99.906, module version = 2.0.0
[ 2.615] (II) Loading extension AMDXVOPL
[ 2.615] (II) Loading extension AMDXVBA
[ 2.617] (II) fglrx(0): UVD feature is enabled(II) fglrx(0):
[ 2.618] (II) fglrx(0): Enable composite support successfully
[ 2.618] (WW) fglrx(0): Option "VendorName" is not used
[ 2.618] (WW) fglrx(0): Option "ModelName" is not used
[ 2.618] (II) fglrx(0): X context handle = 0x1
[ 2.618] (II) fglrx(0): [DRI] installation complete
[ 2.618] (==) fglrx(0): Silken mouse enabled
[ 2.618] (==) fglrx(0): Using HW cursor of display infrastructure!
[ 2.618] (II) fglrx(0): Disabling in-server RandR and enabling in-driver RandR 1.2.
[ 2.735] (II) fglrx(0): Framebuffer compression enabled: mcAddr=0xf407a40000 width=0xa00 height=0x3267
[ 2.735] (--) RandR disabled
[ 2.735] (II) Initializing built-in extension Generic Event Extension
[ 2.735] (II) Initializing built-in extension SHAPE
[ 2.735] (II) Initializing built-in extension MIT-SHM
[ 2.735] (II) Initializing built-in extension XInputExtension
[ 2.735] (II) Initializing built-in extension XTEST
[ 2.735] (II) Initializing built-in extension BIG-REQUESTS
[ 2.735] (II) Initializing built-in extension SYNC
[ 2.735] (II) Initializing built-in extension XKEYBOARD
[ 2.735] (II) Initializing built-in extension XC-MISC
[ 2.735] (II) Initializing built-in extension SECURITY
[ 2.735] (II) Initializing built-in extension XINERAMA
[ 2.735] (II) Initializing built-in extension XFIXES
[ 2.735] (II) Initializing built-in extension RENDER
[ 2.735] (II) Initializing built-in extension RANDR
[ 2.735] (II) Initializing built-in extension COMPOSITE
[ 2.735] (II) Initializing built-in extension DAMAGE
[ 2.736] ukiDynamicMajor: found major device number 251
[ 2.736] ukiDynamicMajor: found major device number 251
[ 2.736] ukiOpenByBusid: Searching for BusID PCI:6:0:0
[ 2.736] ukiOpenDevice: node name is /dev/ati/card0
[ 2.736] ukiOpenDevice: open result is 13, (OK)
[ 2.736] ukiOpenByBusid: ukiOpenMinor returns 13
[ 2.736] ukiOpenByBusid: ukiGetBusid reports PCI:6:0:0
[ 2.842] (II) AIGLX: Loaded and initialized OpenGL driver(II) GLX: Initialized DRI GL provider for screen 0
[ 2.857] (II) fglrx(0): Enable the clock gating!
[ 2.872] (II) fglrx(0): Desktop Vsync is enabled.
[ 2.872] (II) fglrx(0): Setting screen physical size to 508 x 285
[ 2.901] (II) config/udev: Adding input device Power Button (/dev/input/event2)
[ 2.901] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2.901] (II) LoadModule: "evdev"
[ 2.901] (II) Loading /usr/lib/xorg/modules/input/evdev_drv.so
[ 2.902] (II) Module evdev: vendor="X.Org Foundation"
[ 2.902] compiled for 1.12.3.901, module version = 2.7.3
[ 2.902] Module class: X.Org XInput Driver
[ 2.902] ABI class: X.Org XInput driver, version 16.0
[ 2.902] (II) Using input driver 'evdev' for 'Power Button'
[ 2.902] (**) Power Button: always reports core events
[ 2.902] (**) evdev: Power Button: Device: "/dev/input/event2"
[ 2.902] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2.902] (--) evdev: Power Button: Found keys
[ 2.902] (II) evdev: Power Button: Configuring as keyboard
[ 2.902] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input2/event2"
[ 2.902] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 6)
[ 2.902] (**) Option "xkb_rules" "evdev"
[ 2.902] (**) Option "xkb_model" "evdev"
[ 2.902] (**) Option "xkb_layout" "us"
[ 2.902] (**) Option "xkb_variant" "dvp"
[ 2.913] (II) config/udev: Adding input device Power Button (/dev/input/event1)
[ 2.913] (**) Power Button: Applying InputClass "evdev keyboard catchall"
[ 2.913] (II) Using input driver 'evdev' for 'Power Button'
[ 2.913] (**) Power Button: always reports core events
[ 2.913] (**) evdev: Power Button: Device: "/dev/input/event1"
[ 2.913] (--) evdev: Power Button: Vendor 0 Product 0x1
[ 2.913] (--) evdev: Power Button: Found keys
[ 2.913] (II) evdev: Power Button: Configuring as keyboard
[ 2.913] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1"
[ 2.913] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 7)
[ 2.913] (**) Option "xkb_rules" "evdev"
[ 2.913] (**) Option "xkb_model" "evdev"
[ 2.913] (**) Option "xkb_layout" "us"
[ 2.913] (**) Option "xkb_variant" "dvp"
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=11 (/dev/input/event14)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=10 (/dev/input/event15)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=9 (/dev/input/event16)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=8 (/dev/input/event17)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=7 (/dev/input/event18)
[ 2.913] (II) No input driver specified, ignoring this device.
[ 2.913] (II) This device may have been added with another device file.
[ 2.913] (II) config/udev: Adding input device HDA ATI HDMI HDMI/DP,pcm=3 (/dev/input/event19)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Surround (/dev/input/event10)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Front (/dev/input/event11)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line (/dev/input/event4)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Rear Mic (/dev/input/event5)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Front Mic (/dev/input/event6)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Front Headphone (/dev/input/event7)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out Side (/dev/input/event8)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device HDA Intel PCH Line Out CLFE (/dev/input/event9)
[ 2.914] (II) No input driver specified, ignoring this device.
[ 2.914] (II) This device may have been added with another device file.
[ 2.914] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event12)
[ 2.914] (**) Logitech USB Receiver: Applying InputClass "evdev pointer catchall"
[ 2.914] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[ 2.914] (**) Logitech USB Receiver: always reports core events
[ 2.914] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event12"
[ 2.914] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[ 2.914] (--) evdev: Logitech USB Receiver: Found 20 mouse buttons
[ 2.914] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[ 2.914] (--) evdev: Logitech USB Receiver: Found relative axes
[ 2.914] (--) evdev: Logitech USB Receiver: Found x and y relative axes
[ 2.914] (II) evdev: Logitech USB Receiver: Configuring as mouse
[ 2.914] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[ 2.914] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[ 2.914] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2.914] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.0/input/input12/event12"
[ 2.914] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: MOUSE, id 8)
[ 2.914] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[ 2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[ 2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/mouse0)
[ 2.915] (II) No input driver specified, ignoring this device.
[ 2.915] (II) This device may have been added with another device file.
[ 2.915] (II) config/udev: Adding input device Logitech USB Receiver (/dev/input/event13)
[ 2.915] (**) Logitech USB Receiver: Applying InputClass "evdev keyboard catchall"
[ 2.915] (II) Using input driver 'evdev' for 'Logitech USB Receiver'
[ 2.915] (**) Logitech USB Receiver: always reports core events
[ 2.915] (**) evdev: Logitech USB Receiver: Device: "/dev/input/event13"
[ 2.915] (--) evdev: Logitech USB Receiver: Vendor 0x46d Product 0xc52f
[ 2.915] (--) evdev: Logitech USB Receiver: Found 1 mouse buttons
[ 2.915] (--) evdev: Logitech USB Receiver: Found scroll wheel(s)
[ 2.915] (--) evdev: Logitech USB Receiver: Found relative axes
[ 2.915] (II) evdev: Logitech USB Receiver: Forcing relative x/y axes to exist.
[ 2.915] (--) evdev: Logitech USB Receiver: Found absolute axes
[ 2.915] (II) evdev: Logitech USB Receiver: Forcing absolute x/y axes to exist.
[ 2.915] (--) evdev: Logitech USB Receiver: Found keys
[ 2.915] (II) evdev: Logitech USB Receiver: Configuring as mouse
[ 2.915] (II) evdev: Logitech USB Receiver: Configuring as keyboard
[ 2.915] (II) evdev: Logitech USB Receiver: Adding scrollwheel support
[ 2.915] (**) evdev: Logitech USB Receiver: YAxisMapping: buttons 4 and 5
[ 2.915] (**) evdev: Logitech USB Receiver: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 2.915] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1d.0/usb4/4-1/4-1.7/4-1.7:1.1/input/input13/event13"
[ 2.915] (II) XINPUT: Adding extended input device "Logitech USB Receiver" (type: KEYBOARD, id 9)
[ 2.915] (**) Option "xkb_rules" "evdev"
[ 2.915] (**) Option "xkb_model" "evdev"
[ 2.915] (**) Option "xkb_layout" "us"
[ 2.915] (**) Option "xkb_variant" "dvp"
[ 2.915] (II) evdev: Logitech USB Receiver: initialized for relative axes.
[ 2.915] (WW) evdev: Logitech USB Receiver: ignoring absolute axes.
[ 2.915] (**) Logitech USB Receiver: (accel) keeping acceleration scheme 1
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration profile 0
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration factor: 2.000
[ 2.915] (**) Logitech USB Receiver: (accel) acceleration threshold: 4
[ 2.915] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event0)
[ 2.915] (**) AT Translated Set 2 keyboard: Applying InputClass "evdev keyboard catchall"
[ 2.915] (II) Using input driver 'evdev' for 'AT Translated Set 2 keyboard'
[ 2.915] (**) AT Translated Set 2 keyboard: always reports core events
[ 2.915] (**) evdev: AT Translated Set 2 keyboard: Device: "/dev/input/event0"
[ 2.915] (--) evdev: AT Translated Set 2 keyboard: Vendor 0x1 Product 0x1
[ 2.915] (--) evdev: AT Translated Set 2 keyboard: Found keys
[ 2.915] (II) evdev: AT Translated Set 2 keyboard: Configuring as keyboard
[ 2.915] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input0/event0"
[ 2.915] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 10)
[ 2.915] (**) Option "xkb_rules" "evdev"
[ 2.915] (**) Option "xkb_model" "evdev"
[ 2.915] (**) Option "xkb_layout" "us"
[ 2.915] (**) Option "xkb_variant" "dvp"
[ 2.915] (II) config/udev: Adding input device PC Speaker (/dev/input/event3)
[ 2.915] (II) No input driver specified, ignoring this device.
[ 2.915] (II) This device may have been added with another device file.
[ 2.917] (II) fglrx(0): Restoring Recent Mode via PCS is not supported in RANDR 1.2 capable environments
[ 7.513] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[ 7.513] (II) fglrx(0): Using EDID range info for horizontal sync
[ 7.513] (II) fglrx(0): Using EDID range info for vertical refresh
[ 7.513] (II) fglrx(0): Printing DDC gathered Modelines:
[ 7.513] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 7.513] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 7.513] (II) fglrx(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 7.513] (II) fglrx(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 7.513] (II) fglrx(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
[ 10.738] (II) fglrx(0): EDID vendor "SAM", prod id 1316
[ 10.738] (II) fglrx(0): Using hsync ranges from config file
[ 10.738] (II) fglrx(0): Using vrefresh ranges from config file
[ 10.738] (II) fglrx(0): Printing DDC gathered Modelines:
[ 10.738] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2008 2052 2200 1080 1084 1089 1125 +hsync +vsync (67.5 kHz eP)
[ 10.738] (II) fglrx(0): Modeline "1920x1080"x0.0 148.50 1920 2448 2492 2640 1080 1084 1089 1125 +hsync +vsync (56.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1390 1430 1650 720 725 730 750 +hsync +vsync (45.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x720"x0.0 74.25 1280 1720 1760 1980 720 725 730 750 +hsync +vsync (37.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "720x576"x0.0 27.00 720 732 796 864 576 581 586 625 -hsync -vsync (31.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "720x480"x0.0 27.00 720 736 798 858 480 489 495 525 -hsync -vsync (31.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "800x600"x0.0 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e)
[ 10.738] (II) fglrx(0): Modeline "800x600"x0.0 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e)
[ 10.738] (II) fglrx(0): Modeline "640x480"x0.0 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1024x768"x0.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x800"x0.0 71.00 1280 1328 1360 1440 800 803 809 823 +hsync -vsync (49.3 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x960"x0.0 108.00 1280 1376 1488 1800 960 961 964 1000 +hsync +vsync (60.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1280x1024"x0.0 108.00 1280 1328 1440 1688 1024 1025 1028 1066 +hsync +vsync (64.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1440x900"x0.0 88.75 1440 1488 1520 1600 900 903 909 926 +hsync -vsync (55.5 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1600x1200"x0.0 162.00 1600 1664 1856 2160 1200 1201 1204 1250 +hsync +vsync (75.0 kHz e)
[ 10.738] (II) fglrx(0): Modeline "1680x1050"x0.0 119.00 1680 1728 1760 1840 1050 1053 1059 1080 +hsync -vsync (64.7 kHz e)
Here's the Xorg.conf:
Section "ServerLayout"
Identifier "aticonfig Layout"
Screen 0 "aticonfig-Screen[0]-0" 0 0
EndSection
Section "Module"
EndSection
Section "Monitor"
Identifier "aticonfig-Monitor[0]-0"
Option "VendorName" "ATI Proprietary Driver"
Option "ModelName" "Generic Autodetecting Monitor"
Option "DPMS" "true"
EndSection
Section "Device"
Identifier "aticonfig-Device[0]-0"
Driver "fglrx"
BusID "PCI:6:0:0"
Option "OpenGLOverlay" "0"
EndSection
Section "Screen"
Identifier "aticonfig-Screen[0]-0"
Device "aticonfig-Device[0]-0"
Monitor "aticonfig-Monitor[0]-0"
DefaultDepth 24
SubSection "Display"
Viewport 0 0
Depth 24
EndSubSection
EndSection
Section "DRI"
Mode 0666
EndSection
Setting the PCI BusID in Xorg.conf seems to have no effect, even if I set it to 6:0:0 or 7:0:0, its still the same.
Do I need to set AutoAddDevices off?

MisterAnderson wrote:Does the same happen with the opensource radeon drivers? (xf86-video-ati)
Thanks for the reply!
The open source driver doesn't support my card yet. I tried installing it first since its the recommended driver, but Xorg couldn't detect any display at all.
It seems the PCI BusID is not being read from the xorg.conf file. There's auto detection everytime the PC boots.
Last edited by hdhiman (2012-10-04 00:43:52)

Have an HP Pavilion DV7 with Radeon HD6490M Graphics Card. Photoshop doesn't recognize it.

Photoshop CC doesn't recognize my other video card, which is a Radeon HD6490M. Can't utilize 3D tools. Is there something wrong with this particular video card that won't allow it to be recognized?

Here's one idea although it is for a DV6.
First off, reboot and press F10 to go into your BIOS.
Switch the Graphics settings from "dynamic" to "fixed". This will ensure that your computer will not use the default Intel card. I'm not sure why, but it seems as though Rage kept using that card regardless of my settings in Windows.
Gene

Switched CPU now MOBO doesn't Boot

I have an MSI 6378 Ver 3 Mobo. Up until this afternoon it worked great. It was running an XP1800+ CPU. I had someone at work who upgraded and gave me their XP2000+ cpu, so I figured, what the hell. I installed it, but the system would suddenly power down when it started to boot into windows. I would then have to remove all power from the system (disconnect the cord) before I could power it up. So I figured I got a bum CPU and put the old one in. With the old CPU the monitor won't come on, so I don't even know if it is getting to post or not. It sounds like things are spinning up, but I don't have any display. I have a seperate PCI video card, and I get a display with the bad CPU. Can anyone give me some suggestions what I did to my board? I really don't want to purchase a new board/CPU/memory combo if I can avoid it.
Thanks,
Lee

Hello,
You know that you only need a thin layer on the CPU DIE (thinner than paper).
And a small layer on the heatsink.
What heatsink are you using?
Why the XP1800+ wont post?
When you put the XP2000+ in the board runs the CPU at 1.667Ghz.
If you swap CPU's the board may try to run the XP1800+ at 1.667Ghz instead of 1.5Ghz and with the locked CPU's it will cause the PC not to POST.
So you should clear the cmos everytime you change CPU's.
What other components are you using and power supply?
Are you running the CPU at the correct speeds?

Kernel26 package now doesn't boot [FIXED!]

I grabbed the latest kernel pkg. didn't do lilo -v
and now it doesn't boot at all! [stop at the beggining of ..........]
well shouldnt at least boot the last one? [or automatically do lilo -v]
plz help me now
thanks

after a lot of testing and luck I was able to boot arch again [update lilo that is]
what did I do: [i did all that because lilo refuses either to write the map file, or protests about /dev/hda or /dev/discs/disc0/disc {depending if it was Slack or Arch}]
I booted with SlackWare 9.1 Rescue/Install CD {which has vfat}
and which plays without devfs [so /dev/hdb8 was my root arch]
I mounted my arch root
mount -t reiserfs /dev/hdb8 /tmp
I change the /tmp/etc/lilo.conf to:
boot=/dev/hda
vga=792
default=windows
timeout=300
lba32
prompt
image=/tmp/boot/vmlinuz26 # important change
label=arch
root=/dev/hdb8
read-only
other=/dev/hda1
label=windows
/boot [the slackware's cd's one] links to /mnt/boot so I did
mkdir /mnt/boot
and then tried to play with lilo a bit
. /tmp/sbin/lilo -C /tmp/etc/lilo.conf -m /tmp/boot/map -M /dev/hda mbr -v
with the above command I have a boot.0300
in /mnt/boot directory
so in the end I just did
cp /mnt/boot/boot.0300 /tmp/boot/
which overwrote the BAD AND UGLY AND OLD [and at last] boot.0300 with the new one [that containted info about the new kernel]
I prayed to Buddha a bit, and then reboot. I there chose arch and OMFG! i was able to boot it
a) I love LILO
b) I love Slackware
c) I love Arch [though I sumbitted some bug reports about the Rescue CD]
mostly I love the fact that I lost some hours do make it work, but now it works as before. On the other hand, I always remember myself trying for days to fix the windows, and then give up [or if i could hack it in a way that would work, then it would be giving me Blue Screens [now dark blue in win2k/xp] of DEATH]
so I must say I love the Penguin
yeahhhhhhhhh
thanks to everyone that helped.
I hope the pkger of kernel would soon add the WARNING [sumbitted bug for that too] and if anyone forgets it or wants to play [like me] then I hope for him that he reads this post, and make it work [i could work with Arch's Live CD too, not sure]
that's all baby.
another success story yeahhhhhhhhh!! :$

Unable to Launch Adobe Premiere Pro CS6 using High-Performance on AMD Radeon Graphic Card

I have been unable to launch Adobe Premiere Pro since installing it with the error message "Adobe Premiere Pro could not find any capable video play modules. Please update your video display drivers and start again"
Here are my specs:
Lenovo Ideapad U400
Windows 7 (64bit)
Intel i5 2.5 ghz processor
AMD Radeon 6470M graphics card
The only occasion during which I have successfully launched Premiere Pro was after reverting to the default graphics card on my computer and uninstalling AMD Radeon, otherwise, I have tried to change Premiere Pro to run on High-Performance on Catalyst Control Center to no avail, I do not wish to revert to the Standard Graphics Card as it slows down my computers performance one hell of a lot, neither do I wish to have to constantly uninstall and reinstall my AMD Radeon Graphics Card when I use Premiere Pro. Thank you for your time.

Update:
- with Intel (R) HD Graphics Card disabled, Catalyst Control Center reports that no AMD Graphic card is installed
- using Device Manager under Control Panel, AMD Radeon 6470M was verified to be up-to-date
- Premiere Pro works so long as I disable the Intel card before launch, however, I re-enable it upon startup to get rid of the 800x600 resolution
- AMD Mobility Radeon Driver Verification Tool is unable to verify and update my driver, refers me to lenovo to update it.
- My graphics card is up-to-date as verified by lenovo
- Intel (R) HD Graphics Card now up-to-date
- Display currently mainly using Intel (R) HD Graphics Card (Possibly why it caps resolution at 1024x768 when disabled) I'm not sure how to switch the main Graphics Card used, Catalyst Control Center doesn't seem to have the option.
- when disabled, computer reverts to vgasave instead of Radeon
- Disabling Radeon does nothing to existing display
- After updating my Intel card, Catalyst Control Center reported CCC was not supported by the current display adapter
- CCC worked after rolling back Intel card
From what I infer, I believe the problem to root from my intel card being the main card used, if there is anyway to switch my radeon card to the default instead of the Intel card, do tell me, I believe this may solve the problem, I apologise for troubling you guys, and I'm starting to feel that I shouldn't be troubling Adobe with my problem with AMD, this discussion is probably really out of place but I hope it will help out others with a similar problem.

Discrete graphics card not detected.

First post.
System specs:
Mobo: MSI Z77A-GD55
CPU: Intel Ivy Bridge i5 3570K
GPU: eVGA GTX 580
PSU: NZXT Hale82 750W 80 Certified
RAM: G Skill Sniper Series 1866 8Gb DD3
SSD: Corsair Force Series GT 240G
For starters, I was running a CoolerMaster 1000W PSU and the eVGA 580 GTX in my old system. Upon upgrading, I transferred those units to the new system but can not boot up system with GTX 580. Onboard graphics work fine, so I went ahead and installed Windows onto the SSD with no problems. Once in Windows, I installed the latest Motherboard updates, and even flashed the BIOS to latest 1.4 build. Still no luck with the graphics card working on boot up.
Things I've tried:
- GTX 580 boots up and works fine (hence the system running now) on older Motherboard.
-Ruling out a defective GPU unit.
- Both Coolermaster and NZXT PSU run the GTX 580 on older Motherboard.
-Ruling out a defective PSU unit.
- Graphics card (GTX 580) would not boot up on ASUS P8Z77-V Pro Motherboard, nor the new one MSI Z77A-GD55
-Possibly ruling out defective Motherboards.
- Replaced i5 3570k CPU with yet another i5 3560k CPU (Same issue)
-Ruling out a defective CPU
- When using onboard VGA, I can get into the BIOS and the Graphics settings are set to PEG (PCI-E Graphics). Although when I shut down and install my GtX 580, still no boot up.
- Moved the GTX 580 between the 2 top PCI-E slots, to no avail.
- Moved 1 stick of RAM between the 4 DIMM slots and still not working.
-Reseated graphics card and made sure the 8-pin and 6-pin connectors were firmly intact.
I have done a lot of research, but have yet to find a definitive answer to my problem. I'm not ruling out a 3rd motherboard that may be defective, but I feel this is highly unlikely. Again, everything works and checks out in the system specs with the onboard graphics enabled.
I thought I'd try here to get some addition ideas from the group. Thanks for reading.

Quote from: HU16E on 02-July-12, 12:47:41
Try this; Shutdown, remove the discrete card, connect to the onboard, restart and boot all the way into Windows, restart to the UEFI/BIOS, change the graphics setting to IGD, save and enter, let it reboot into Windows, hard shutdown. Restart into UEFI/BIOS, change graphics setting to PEG, save and enter first, then hit the reset button and enter immediately back into the UEFI/BIOS checking to make sure the PEG setting is in fact set, then hard shutdown. Install the discrete card connecting all the power cables and monitor cable, start and see if it now boots into Windows with the graphics now working.
This merry-go-round procedure worked for me on 3 Z68's, no reason it won't work on a Z77.
I will try this procedure now. If it works, I will have to buy you lunch because I have NEVER heard of such hoopla!

Second Graphics Card for HDTV Output + HDV Live Preview

Hi guys,
I have a few questions about hardware and Premiere Pro CS5. I am using Windows 7 x64 with a Dual DVI nVidia GeForce 7950GT which is outputting to two DVI LCD monitors. I want to install a second graphics card so I can look at the main preview window in Premiere on my HD LCD TV and would like to know what the best plan of attack is. Also, I want to be able to preview my HDV captures on my HDTV as relying on the 2.5" LCD on my Sony HVR is not eye-friendly!
I am thinking about either selling the 7950GT and buying a GeForce 470GTX which has 2 dvi and 1 mini-hdmi, or, keeping the 7950 and buying a cheapish 2nd graphics card to just use for the HDTV. What do you guys think is the best option?
This is the graphics card I am thinking of getting ( http://www.asus.com/product.aspx?P_ID=hs87bcOLPd9irXRk&templete=2 ) an ASUS ENGTX470 / 2DI / 1280 MD5, my server can just handle it's power requirements, but I am happy to upgrade the power supply if this card will ouput to 2 DVI monitors and also to a HD TV with a mini-HDMI to HDMI adapter. An Antec 1000w power supply is only about $225!
Or, I can take the cheap option and get an NVIDIA Quadro FX 580 by Leadtek( http://www.leadtek.com/eng/workstation_graphics/overview.asp?lineid=2&pronameid=491&check= f ) which is a cheapy with 2 HDMI and 1 DVI. I guess there are other PCI-X graphics cards out there to choose from which are probably fine, but it would be awesome to know what some of you guys are using.
Surely there are others out there that already have a dual monitor setup with a third LCD TV for previewing?
Anyhelp would be much appreciated!

@Harm: Thanks for that, I thought a card with three outputs would be too good to be true. I think I will buy a much cheaper 2nd PCI-X graphics card and just use its HDMI output for the HDTV. We will be doing a complete overhaul of this machine sometime in the future and I will buy an awesome graphics card with power supply to boot then.
@J-MS: Currently we are moving away from a Matrox Axio HD as their support for Windows 7 and CS5 has been lackluster, and I don't reward companies that provide zero or no support with future business. I would rather be free of a third-parties proprietary codecs, plugin and decoders.
@Thrill: Thanks for the link to that post, I read through it and it looks like I need to get a second card that is the same make as the existing card (ie. nVidia), which is what Harm was saying. When I capture from the tape deck, the capture preview window in Premiere goes blue and says in 5 different languages that the preview is going to show on the input device, or words to that effect. I am therefore looking at a 2.5" lcd for capturing! fail. I don't know why that is happening now to be honest, maybe it was because I was in a Matrox HD sequence before and the input device wasn't set correctly? I will double-check it again and see what the deal is.
I am very tempted to just get an el-cheapo nVidia 8400GS Turbo Cache 512M DDR3 DVI HDMI which is only $39!!!! It has HDMI and is small and has a very low power drain on the system. If it outputs to the HDTV then that's all I need, if it doesn't, I sell it on ebay for $25 and lose $14, big deal.

975X Platinum Graphics Card Compability

Hi!
I've just got a new graphics card and it won't boot. The monitors won't get any signal at all.
My set up:
PSU: Corsair 850W (tried a couple of different PSUs)
CPU: Intel Core 2 Duo, 6600 @ 2.4ghz
RAM: 4gb Corsair.
GPU: Nvidia 8800 GTS (works fine), ATI Radeon HD 6870 (does not boot).
I've tried the new Graphics card in another computer, works fine. I've tried other "older" graphics cards in my computer, works fine. I've tried other "newer" graphics cards in my computer, with the same error, does not boot.
It seems like the mainboard won't work together with the new graphics cards. But I haven't been able to find any information about this, i.e. which cards should work, and why?

Thanks for the quick response!
The ones i tested that didn't work was in the Radeon 5xxx/6xxx series, don't remember exactly, but at least two. And the GeForce 470 I tried worked, which seems to match what you say. I think the solution for me will be to find a new GeForce instead, don't have the time, nor the money to upgrade the mainboard.
At least now I know what the problem is, again, thanks a lot.

K9N Platinum - Doesn't boot with PWR2 connected

Hi,
I've just built a new PC with a K9N Platinum Motherboard (7250 Ver 1.0)
I immediately discovered a problem:
-If I connect to the power supply the PWR2 Molex (the additional power connector on the motherboard, to provide additional power to the video card) the system doesn't boot. Computer's LEDs get on for half a second, then it shuts down.
-If I deconnect the PWR2 connector, computer boots fine.
Bios already flashed to 1.51... no results.
It sounds weird to me. I have an Enermax Noisetaker II 485W PSU, the CPU is an Athlon X2 65W...
Have I got a damaged mainboard?
Thanks for support

Quote from: WillyTP on 15-February-07, 05:36:01
Just tried... nothing. Lights and fans turns on for half a second, then everything dies.
I tried to remove video card too, nothing changes :(
sound like somethink is shorted. try take board of case and retry. it maybe dumb question, but are you connect 4pin cable in a right direction?(i know its can be plugged in one way only, but if you use little more force can be done...)

Can I upgrade my HP ENVY dv7-7300 Quad graphic card?

I've heard that most laptops graphic cards now a days can't be upgraded, but I have an HP ENVY dv7-7300 Quad and I was wondering if it is possible to upgrade its graphic card to Nvidia GT 635m?
Thanks

Hi,
Basically you can, nothing can stop you, with a cost and I believe this cost may be more expensive than buying a new computer because you have to take into account:
New card price, and WHERE you can buy it because laptop cards are not the same as desktop cards. You can't buy from any normal shop,
Need new system board (may be),
Need new cooling system because generally speaking more powerfull card pumps out more heat (you want more powerfull card don't you?).
May need new PSU because your current PSU may not suitbale to the card. (I ordered a machine with Nvidia card and I needed to order a 90W charger at the same time, not the normal 65W charger. They simply rejected my order).
Labor cost.
Many, many packets of Asprin.
Hope this helps.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Uninstalled graphic card - now unit doesn't boot

Similar Messages

Maybe you are looking for