Unity Connection Auto Attendant direct to voice mail, MWI issue

hi,
First time encountering this issue with call transfer from AA and MWI.
An Auto Attendant have been setup for a branch office. All employees at the Branch office phones are assigned a DID.
Customers can dial the 10 digit or dial the main line (auto attendant) and then dial the last 4 digit extension to reach the employee.
Problem I am having is there is a range of numbers that when being transferred from AA, goes directly to voicemail. Also when there is a message left on the voicemail, the MWI is not lit. It does show the envelope icon and the message "you have vociemail" on the phone display.
I can call the DID directly and it does not go directly to voicemail but MWI is still not on when a message is left.
This only happens within a range of numbers.. for example, I have 50 DID assigned to this office from XXX-XXX-0100 to XXX-XXX-0150. Only the phones within the range of XXX-XXX-0120 to XXX-XXX-0130 have this issue with the AA going directly to vociemail and MWI not on when a message is left.
For phones outside this range of numbers, AA transfer works fine and MWI works.
anyone ran into this issue before?
thank in advance.

Hi,
The range in which you are facing issue is XXX-XXX-0120 to XXX-XXX-0130, just try to open any one of the extension in this range and go to edit -- transfer rules -- standard/alternate (if alternate is enabled) -- Transfer calls -- may be this is set to Greetings. If so the transferred call goes to voicemail directly. Try enabling Extension.
Just try this for one extension and see...
Hope this helps, i had the same issue.
Regards
Jagadish G

Similar Messages

Receiving Calls Problem - going directly to voice mail

My iPhone is set to check for email every 15 minutes. If someone calls at the time iPhone is automatically checking for email, the call goes directly to voice mail.
Worse it doesnt even show up as a missed call.
I understand that Edge is turned off when making a call.
But this happens automatically so I have no control over this feature. I tried calling myself from a landline at the time iPhone was checking for emails and verified this issue.
Does anyone else have the same problem - what is the solution?
Thanks

"That's the way that GSM/EDGE works. The radio can only do one thing at a time. If it's doing data, then the voice call goes right to VM and you don't get notified until the VM gets in."
That is not entirely correct. That is not how GSM/EDGE works. This is how iPhone is designed to work. I have a Nokia N73 and when i am browsing the Web using EDGE (T-Mobile's network), if i get a call, i will be prompted to accept the call. The way that iPhone is designed, it seems to be that Apple values data connectivity more than voice calls. In my opinion, this is probably the wrong way to do it.

IPhone 5s doesn't ring and goes directly to voice mail. Do not disturb is disabled. Have reset network settings and did a hard reset. What am I missing?

iPhone 5s doesn't ring and goes directly to voice mail. Do not disturb is disabled. Have reset network settings and did a hard reset. What am I missing?

Call your phone carrier - that's a problem for them to resolve.

IPHONE 4S incoming calls go directly to voice mail. This is a brand new replacement phone. Prior phone didn't have this problem

IPHONE 4S incoming calls go directly to voice mail. This is a brand new replacement phone. Prior phone didn't have this problem

Slide up from the bottom of your display to access the control panel.
Look for the button (should be at the top) that shows a crescent moon.
Tap that button. It should say "Do not Disturb: Off".
Then try it out and let us know if it worked.

My phone is dropping calls, doesn't ring all the time-goes directly to voice mail, do no recieve alert on when a text is recieved

1-My phone does not ring all the time upon recieving an incoming call, it goes directly to voice mail.
2- Not recieving alert tone upon recieving a text message.
3- Dropping calls also

We have the same problem widespread in our company with iPhone 4's and 5's:
- Fails to establish the call, dials but nothing happens
- Drops the call for no reason even though signal strength is good
- Recevie text alerts to notify of voicemail when the handset has not rung nor does it show missed calls
We migrated someone to a Samsung Galaxy S4 for a month and all these issues went away. Nothing to do with alert tones turned down or faulty silent switches.

Direct to voice mail

a number of calls to me are going direct to voice mail. I am not on the phone at the time. what can I do to get these calls rather than have them go to voice mail

VZW Support, I have a Android Merge by HTC. I have the same problem that Tiger73 described. Beginning two days ago I ceased receiving phone calls and while exploring the cause I saw that my phone was set on "Silent" mode. I thought this had just "happened" inadvertently. I changed it to Normal mode but it kept reverting to Silent. After many attempts, and after removing the battery and reattaching the battery, it is now set to "Normal". I have all volume settings turned all the way up high. When I change the call/ring sound the phone sounds audibly. When I get a gmail msg, the phone makes an audible tone. However, calls made to my phone go immediately to voicemail! PLEASE suggest something else to try. I did the *73 thing already but that has no effect. I have NEVER used call forwarding on this phone. Normally I just turn the sound all the way down if I don't want to hear it ring. Thanks for any help!
Linda H.

Why does my phone call go directly to voice mail when I call my daughter? No others do this.

Why does my phone call go directly to voice mail when I call my daughter. I can call anyone else and talk to the person I call.
I am using the IPhone 4
Your response is that she has it forwarded to voicemail. It is a Samsung -so she wants to know how she un forwards it,. Or is my phone directly to her voicemail. The 'Finger Tips" says to send a call directly to voicemail push On/Off twice. I did not knowingly do that
Message was edited by: EVELYN ESKRIDGE

cowboy
Clarifications... when you say "... only some calls..." and "... someone says they called..." - are these all from from one caller?
After following all these fine suggestions and eliminating them systematically, consider that this kind of stuff is as old as the cellphone system. A few possibilities that occur to me just regarding the network system:
you are in a habitually dead spot area. I have one in my own house!
you travel through many of these dead zones (traditionally called 'low-coverage' areas) - remember how big a deal the coverage maps were to us?
there is an issue with your network service provider's back-end system (my first thought - above)
keep plugging away amigo! I'll bet you get this solved.
CCC

Unity 4.0 - Call Forwarding and Voice Mail

Here is the situation:
We have a DN (5301) that is not associated with a Unity mailbox but is on a 7970 phone. This extension is an "on call" number that is always forwarded to a technicans phone (local 4 digit ext or cell phone).
When a person calls 5301 I want the voicemail of the final destination to answer.
For instance if I had 5301 forwarded to 2000 - I would want 2000's voicemail to answer.
Is there a way to set this up?
Thanks in advance.
Jeff

Hi Jeff,
Sadly this cannot be changed until Unity 5.x (the ability to choose "Last Redirecting Number" in not available in any other Unity version);
Here are the Unity 5.0 release notes;
Route Forwarded Calls by the First or Last Redirecting Number
Cisco Unity supports the option of routing calls based on either the first or last redirecting number when a call is forwarded to Cisco Unity.
Note the following:
This option requires Cisco Unity-CM TSP 8.1(2) or later.
This option is not supported by integrations through PIMG units.
This option can be changed through the Advanced Settings Tool (AST), which is available in Tools Depot.
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/release/notes/501curelnotes.html#wp507371
Call Information Exchanged by the Phone System and Cisco Unity
The phone system and Cisco Unity exchange call information to manage calls and to make the integration features possible. With each call, the following call information is typically passed between the phone system and Cisco Unity:
â¢The extension of the called party.
â¢The extension of the calling party (for internal calls) or the phone number of the calling party (if it is an external call and the phone system supports caller ID).
â¢The reason for the forward (the extension is busy, does not answer, or is set to forward all calls). There is also a reason code for Direct Calls.
Cisco Unified Communications Manager SCCP and SIP trunk integrations can also provide the following call information (the choice of first and last redirecting number is set in the Advanced Settings Tool, which is available in Tools Depot):
â¢Called number
â¢First redirecting number
â¢Last redirecting number
Note Cisco Unity can use either the first redirecting number or last redirecting number, depending on the setting in the Advanced Settings Tool, which is available in Tools Depot.
http://www.cisco.com/en/US/docs/voice_ip_comm/unity/5x/design/guide/5xcudg060.html#wp1040786
If this was just a one-up type of setup you can configure a Voicemail profile (in CCM) for 2000 and apply it to 5301 that will allow this type of Call Forward to 2000's mailbox. The fact that you need this for Multiple Tech's will not work. Is there any way the Techs could use a Shared Line? Then these solutions could be adapoted.
Or in Unity set up Alternate Extensions so that User A is an Alternate Extension for User B etc. Sharing a Cisco Unity Voice Mail Box between Two or More IP Phones
Configure Alternate Extensions
Open the Unity System Administrator web page.
Navigate to the subscriber's profile. Select Subscribers > Find and Select a Subscriber > Enter Subscriber Information then click Find and click the Subscriber's name for the subscriber that owns the primary phone (2000).
When the subscriber page comes up, select the Alternate Extensions option and click Add.
Enter the alternate extension number (in this case 5301) and click the Save icon.
From this good Unity doc;
http://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_configuration_example09186a008015ceec.shtml#steps
Hope this helps!
Rob

Unity 3.1(5) prblm retrieving voice mail for single user

I have a customer with one user who cannot retrieve their voice mail new / saved. When she logs into via their extension it prompts for option 1 new 2 saved. Taking option 1 and it loops back to the begining. I have refreshed and sync MWI and also checked the TSP settings and also the Exchange server. Have rebooted Unity and still the issue remains. Any ideas or possible resolves?

Did you check the phone? is it same from any phone? re create the mail box and see another option.
Baseer.

Unity Express voice mail timing issue.

Hi,
I have installed one uc520 at one of our customer. i configured voice mail but there is one issue with the voice mail timing. Suppose i retrive the voice mail the voice mail prompt is giving the wrong time. Suppose I send a voice mail to a subscriber at 3pm, the voice mail prompt is saying 'message send at 4 pm'.
I checked both cme and cue clock settings and both are showing the correct time.
Can anybody help me on this issue
Regards
Thejas

Are the calls to CUE getting dropped when you dial from an IP Phone at site 1 (callmanager) ?
How is the CME router setup in Callmanager ? Is it added as a regular H323 gateway or a H225 trunk ? Either ways, make sure the gateway registers with the correct IP that is used in Callmanager.
So if CME has a wan ip (a.a.a.a) and a lan ip (b.b.b.b), if you add b.b.b.b as the CME gateway's ip address in Callmanager, then you need to bind the H323 ip address as follows.
interface fa0/0
ip add b.b.b.b
h323-gateway voip bind srcaddr b.b.b.b
Most likely the CME gateway is sending calls to Callmanager using ip address a.a.a.a which is the wan ip, through which it has the default route to Callmanager.
Hope that makes sense!

Calls going directly to voice mail

Since this morning I am not receiving calls - in testing the call rings once then goes to voice mail. I called Apple Support and was told to do a Reset, which took care of the problem for about an hour and now it is back.
Is anyone else experiencing this? I use my iPhone for business and this is very disruptive.
I upgraded to 1.1.3 last week - everything has been fine until today!!

People in the past had posted issues with call forward. After they had deactived this feature the calls were still being sent to the forwarding number. Have you used this feature? If so then you need to call AT&T to have it deactivated. If you have not used this feature I would still call AT&T since this appears like an issue one their end. Best of luck.

Unity Express - Incoming calls wont get voice mail

CUE works fine with telephones on my local network. Incoming and outgoing calls work fine.
However when I get an incoming call via SIP trunk the call will not get forwarded to unity express after 10 seconds. The line goes dead.
I searched for another post which suggested the following commands:
telephony-service
call-forward pattern .T
voice service voip
allow connections from h323 to sip
I've double checked them and there's still something wrong.
Here's my current configuration:
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
telephony-service
load 7910 P00403020214
load 7960-7940 P00305000301
max-ephones 24
max-dn 24
ip source-address 192.168.20.1 port 2000
auto assign 1 to 24
system message Comtek
voicemail 3000
max-conferences 8 gain -6
call-forward pattern .T
moh music-on-hold.au
time-webedit
transfer-system full-consult
transfer-pattern 2...
transfer-pattern 3...
directory last-name-first
directory entry 2 2001 name Phone Two 7912
directory entry 3 2000 name Phone One 7970
ephone-dn 1 dual-line
number 2000 secondary 441833000000
call-forward busy 3000
call-forward noan 3000 timeout 10
no huntstop
ephone 1
no multicast-moh
device-security-mode none
mac-address 0017.0EF0.3642
type 7970
button 1:1
So pros, any suggestions?
Thanks

I made a new dial-peer to handle incoming calls as follows.
dial-peer voice 1000 voip
description Incoming SIP
translation-profile incoming SIPin
voice-class codec 1
session protocol sipv2
incoming called-number .T
dtmf-relay rtp-nte
no vad
The translation-profile puts the call through to my 2000 extension.
This is my "show call active voice brief" when an external incoming call is ringing through to my 2000 ephone-dn.
To me this seems to show the dial-peer "1000" matching and using the g711ulaw codec
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
1715 : 552 596706500ms.1 +-1 pid:1000 Answer +441833696807 connecting
dur 00:00:00 tx:0/0 rx:0/0
IP 87.127.240.98:16188 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1715 : 553 596706510ms.1 +-1 pid:20001 Originate 2000 connecting
dur 00:00:00 tx:0/0 rx:0/0
Tele 50/0/1 (553) [50/0/1.0] tx:0/0/0ms None noise:0 acom:0 i/0:0/0 dBm
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
This is the "show call active voice brief" for an external incoming call when the call is established.
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
1731 : 569 597220040ms.1 +3730 pid:1000 Answer +441833696807 active
dur 00:00:02 tx:105/16800 rx:104/16640
IP 87.127.240.98:15162 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1731 : 570 597220060ms.1 +3700 pid:20001 Originate 2000 active
dur 00:00:02 tx:0/0 rx:105/16800
Tele 50/0/1 (570) [50/0/1.0] tx:16180/16180/0ms g711ulaw noise:0 acom:0 i/0:0/0 dBm
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
Not too sure where to go from here.

Treo 800W: Missing Calls, Going Directly to Voice Mail

I am at wit's end. My Treo 800W will roll directly to voicemail for no reason. I've gone through my settings to ensure the box that blocks interuptions during data sessions is unchecked. I've made my active sync a manual operation. Yet I still miss 5 or 6 calls a day!
Any ideas?
And I'm not alone. There are others all over the Treo forums experiencing the same problem. Check here: http://discussion.treocentral.com/showthread.php?t=168727
Post relates to: Treo 800w (Sprint)

I have sprint as well and have that issue. I always though it was because of the service provider. Please let me know what feed back you get with regards to this.
Post relates to: None

Voice Mail Greeting Issue

I cannot reset my outgoing message. I'll record a new one and play it back, but when I call my phone from someone else's they get the old greeting.

Voicemail is a wireless carrier function. call them and ask.

Cisco Unity Express 8.6.6 Voice Mail not deleting when e-mail with attachment deleted

I have a Cisco Unity Communications Manager rel 9.1.2 that supports a remote location with a Unity Express rel 8.6.6 voice mail service module in the voice gateway to insure if WAN goes down the location still has voice mail. We have Voice Mail to E-Mail working. The problem is that when the e-mail with the voice mail is deleted the message stays in the Unity Express Voice Mail Box. All of our local users on the same Call Manager Cluster using a local Unity Connection Cluster rel 9.1.2 have the voicemails deleted when the e-mail is deleted.
How can I resolve this issue?

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Unity Connection Auto Attendant direct to voice mail, MWI issue

Similar Messages

Maybe you are looking for