Unity Express voice mail timing issue.

Hi,
I have installed one uc520 at one of our customer. i configured voice mail but there is one issue with the voice mail timing. Suppose i retrive the voice mail the voice mail prompt is giving the wrong time. Suppose I send a voice mail to a subscriber at 3pm, the voice mail prompt is saying 'message send at 4 pm'.
I checked both cme and cue clock settings and both are showing the correct time.
Can anybody help me on this issue
Regards
Thejas

Are the calls to CUE getting dropped when you dial from an IP Phone at site 1 (callmanager) ?
How is the CME router setup in Callmanager ? Is it added as a regular H323 gateway or a H225 trunk ? Either ways, make sure the gateway registers with the correct IP that is used in Callmanager.
So if CME has a wan ip (a.a.a.a) and a lan ip (b.b.b.b), if you add b.b.b.b as the CME gateway's ip address in Callmanager, then you need to bind the H323 ip address as follows.
interface fa0/0
ip add b.b.b.b
h323-gateway voip bind srcaddr b.b.b.b
Most likely the CME gateway is sending calls to Callmanager using ip address a.a.a.a which is the wan ip, through which it has the default route to Callmanager.
Hope that makes sense!

Similar Messages

Unity Connection Voice Mail Issue

Hi,
I have a weird Unity Connection Voice Mail issue and would appriciate any help i can get. Many thanks in advance.
I have Unity connection 7.0 and CUCM 7.0 integrated in a lab enviroment and here is what happens.
When I place a call internally say from 2001 to 2002, things work as expected, 2002 rings and it goes to voicemail where I can leave voicemail and listen to it from 2002.
However, if I place call from the PSTN to the same number 2002 (or any other number in other sites etc) the call again rings in 2002 and goes to voicemail, unity cnx plays the greetings for 2002 and says record your message as usual. Everything up to point is fine, then when the time on the PSTN phone is showing around 14 seconds into the call unity starts playing, "to send this message press one", if I press one nothing happens.
I have rebuilt unity and cucm, even just configured the bare minimum in the lab and still getting the same result. I tried calling from E1 connection and T1 connection but with the same results.
I have run out of ideas...
===============================
Here is a call trace from an internal call:
CallData, 1, CallerId=2003, CalledId=2002, RedirectingId=2002, Origin=16, Reason=4, CallGuid=8B7859FD6C16417A9A07F507418DD25B, CallerName=, LastRedirectingId=2002, LastRedirectingReason=4, PortDisplayName=PhoneSystem-1-001
Application, 1, 2003, AttemptForward
State, 1, 2003, State - AttemptForward.cde!Dummy
State, 1, 2003, Event is [NULL]
Application, 1, 2003, PHTransfer
State, 1, 2003, State - PHTransfer.cde!LoadInfo
State, 1, 2003, Event is [TrueEvent]
Application, 1, 2003, PHGreeting
State, 1, 2003, State - PHGreeting.cde!PlayGreeting
Display, 1, 2003, Call answered if needed
Display, 1, 2003, Playing greeting for Subscriber: hq2
Display, 1, 2003, No DTMF received
Display, 1, 2003, Playing greeting for Subscriber: hq2
State, 1, 2003, Event is [RecordMsgEvent]
State, 1, 2003, State - PHGreeting.cde!RecordMsg
State, 1, 2003, Event is [NULL]
State, 1, 2003, State - PHGreeting.cde!RunEditMsg
Application, 1, 2003, -->MessageEditing
State, 1, 2003, State - MessageEditing.cde!CheckMsgMenuOpt
State, 1, 2003, Event is [EditMessageMenuEvent]
State, 1, 2003, State - MessageEditing.cde!PlayEditMenu
State, 1, 2003, Event is [HangupEvent]
State, 1, 2003, State - MessageEditing.cde!CheckMsgLength
State, 1, 2003, Event is [ManyEvent]
State, 1, 2003, State - MessageEditing.cde!SendMsg
State, 1, 2003, Event is [TrueEvent]
State, 1, 2003, State - MessageEditing.cde!ConfirmSend
State, 1, 2003, Event is [HangupEvent]
Application, 1, 2003, <--MessageEditing
State, 1, 2003, Event is [HangupEvent]
Display, 1, 2003, Idle
Display, 1, , Dialing (MWI) '2002'
Display, 1, , Idle
and here is a trace from an external (PSTN) call
Trying 142.100.64.13, 5000 ... Open
CallData, 1, CallerId=911, CalledId=2002, RedirectingId=2002, Origin=16, Reason=4, CallGuid=CA3DFD90846C4FE7B0D68298A7698287, CallerName=PSTN Emergency, LastRedirectingId=2002, LastRedirectingReason=4, PortDisplayName=PhoneSystem-1-001
Application, 1, 911, AttemptForward
State, 1, 911, State - AttemptForward.cde!Dummy
State, 1, 911, Event is [NULL]
Application, 1, 911, PHTransfer
State, 1, 911, State - PHTransfer.cde!LoadInfo
State, 1, 911, Event is [TrueEvent]
Application, 1, 911, PHGreeting
State, 1, 911, State - PHGreeting.cde!PlayGreeting
Display, 1, 911, Call answered if needed
Display, 1, 911, Playing greeting for Subscriber: hq2
Display, 1, 911, No DTMF received
Display, 1, 911, Playing greeting for Subscriber: hq2
State, 1, 911, Event is [RecordMsgEvent]
State, 1, 911, State - PHGreeting.cde!RecordMsg
State, 1, 911, Event is [NULL]
State, 1, 911, State - PHGreeting.cde!RunEditMsg
Application, 1, 911, -->MessageEditing
State, 1, 911, State - MessageEditing.cde!CheckMsgMenuOpt
State, 1, 911, Event is [EditMessageMenuEvent]
State, 1, 911, State - MessageEditing.cde!PlayEditMenu
State, 1, 911, Event is [HangupEvent]
State, 1, 911, State - MessageEditing.cde!CheckMsgLength
State, 1, 911, Event is [NULL]
Application, 1, 911, <--MessageEditing
State, 1, 911, Event is [NULL]
State, 1, 911, State - PHGreeting.cde!AfterMsg
State, 1, 911, Event is [NULL]
Display, 1, 911, Idle

Sounds like one way audio from PSTN to your Unity Connection, couple of things to check:
1. ensure your protocols are bound properly on the GW, i.e. SIP/H323/MGCP
2. Make sure IP routing is OK between Unity and the voice gateway
HTH,
Chris

Cisco Unity 7: Voice mail cann't get the name or Number phone of the caller

Hi,
I have installed Cisco Unity Messaging Unified version 7 and integrated with Exchange 2010.
I have two scenario, and I want to know if are normal or not:
1. If the 2 IP phones are subscribed with Cisco Unity: the first IP phone call the other IP phone and let a voice mail. When the second IP phone check his message vocal it can get the name of the caller or his number phone (the message is: You have One message from XXXX) and he get e-mail as objet: Voice Mail from XXXX.
2. If one IP phone is not subscriber with cisco unity call other Ip phone subscribed with cisco unity and let him a voice mail. The second IP phone when check his message vocal it can’t get the name of the caller or his number phone: The message is: You have one voice mail xxxx; without indicate from!! and he get a e-mail as object: Voice mail from Unknown.
Please, I want to know if the second scenario is normal ? if not, who to resolve this problem? I want that he indicate the number of caller same he isn't subscriber with cisco unity?
Thanks a lot,
Best regards,
Omar YUNSI

So for the 2nd scenerio you would want to check what your Message Subjects were set to. For Unity 7 open Web SA, click Configuration and then Message Subjects. Make sure that the Outside Caller Message has %CALLERID% in it somewhere. The value %CALLERNAME% will return unknown if we do not receive a name from the PSTN.
Try setting the Outside Caller Message to:
%U% %P% Voice Message from %CALLERID%
and that should get you your desired results.
The default Message subject is:
%U% %P% Voice Message from %CALLERNAME% (%CALLERID%). So with that it would say Voice Message fom Unknown (xxxx) if it was not able to determine the name of the user which is usually normal from a PSTN call.
Just to note, the From address is always going to say from Unity Messaging System, it will only be the subject that has the extension in it.
Bryan

Unity Connection Voice Mail Only- NO MWI template

I am deploying a site with 8,000 mailboxes. 4,000 of those users are voice mail only without a telephone and will NOT require MWI.
I can manually remove the MWI setting from each mailbox, but I am looking at either a BATCH CSV setting or a TEMPLATE that I can turn OFF mwi when creating the users.
Any ideas?
TIA

Hi there,
This setting change is available via Bulk Edit
Bulk Edit> Messages> Disable MWI functionality for this user
Bulk Edit changed in 8.x from where it was accessed in 7.x.
Here's a clip that speaks to how this is run now. You first search and select all
the users you want to change and then choose Bulk Edit;
To Edit User Account Information in Bulk Edit Mode (some editing from original > this example
is for Caller Input settings but you'll see the point)
Step 1 In Cisco Unity Connection Administration, on the Search Users page, check the applicable user check boxes, and select Bulk Edit.
If the user accounts that you want to edit in bulk do not all appear on one Search page, check all applicable check boxes on the first page, then go to the next page and check all applicable check boxes, and so on, until you have selected all applicable users. Then select Bulk Edit.
Step 2 On the Edit Caller Input page, change settings as applicable.
Note The Status message at the top of the Edit Caller Input page tells you how many user accounts are being edited. Also note that the page is populated only with the fields that you are allowed to edit in bulk mode, and that the fields available for edit also depend on whether all of the user accounts reside on the local server.
Step 3 If applicable, set the Bulk Edit Task Scheduling Fields to schedule the Bulk Edit operation for a later date and/or time.
Step 4 Select Submit.
Step 5 If applicable, continue to change settings for these user accounts on the related pages available from the Edit menu. As you make changes on each page, select Submit before going on to the next page to make additional changes.
http://www.cisco.com/en/US/docs/voice_ip_comm/connection/8x/user_mac/guide/8xcucmac090.html#wp1049545
Try a couple of test users first to come up with the exact plan.
If you prefer you can also use Bulk Edit via .csv
As a test here I tried the Bulk Edit and chose;
User with Voicemail > Users referenced in this CSV file > Next
This then allowed me to browse to an existing "basic" .csv that I had
used to create a test user recently when playing with BAT. In this .csv
I had one user named Bob Uncle with DN/ext 5126. So when I used this method
the Bulk Edit tool (smart puppy ) selected only Bob Uncle for my edit choices
and I was able to change the Disable MWI functionality for this user
Again, please try manipulating some test users to perfect
your methodology.
I have attached the test .csv I used
Cheers!
Rob
Attachments: buncletest Mailboxes.csv.zip (255 bytes)
"Show a little faith, there's magic in the night" - Springsteen

Unity Connection Voice Mail ports

Hi experts
I hava simple question.
I have a UCS M3BE server with 2 CPU, as per the link http://www.cisco.com/en/US/docs/voice_ip_comm/connection/9x/supported_platforms/9xcucspl.html#wp810181 with 2 No's of CPU it supports only 100 ports per Virtual Machine and for the cluster it supports 200 ports.so in the CUCM Voice Mail Port Wizard i shld put figures 200 or 100??,
i think i shld put voice mail ports 100 on CUCM with name CiscoUM1-VI with 100 ports when selecting ports on CUC-publisher
then again creating voice mail ports 100 on CUCM with name CiscoUM2-VI with 100 ports when selecting ports on CUC-subscriber
Thanks

Hi Jack,
Can you try installing the cop file from the following link
https://supportforums.cisco.com/community/netpro/collaboration-voice-video/unified-comm-application/blog/2013/04/17/unity-connection-911-unable-to-create-more-than-8-ports
Although this bug fix is for installations with one CPU you can give it a try.
HTH
Manish

Unity Connection Auto Attendant direct to voice mail, MWI issue

hi,
First time encountering this issue with call transfer from AA and MWI.
An Auto Attendant have been setup for a branch office. All employees at the Branch office phones are assigned a DID.
Customers can dial the 10 digit or dial the main line (auto attendant) and then dial the last 4 digit extension to reach the employee.
Problem I am having is there is a range of numbers that when being transferred from AA, goes directly to voicemail. Also when there is a message left on the voicemail, the MWI is not lit. It does show the envelope icon and the message "you have vociemail" on the phone display.
I can call the DID directly and it does not go directly to voicemail but MWI is still not on when a message is left.
This only happens within a range of numbers.. for example, I have 50 DID assigned to this office from XXX-XXX-0100 to XXX-XXX-0150. Only the phones within the range of XXX-XXX-0120 to XXX-XXX-0130 have this issue with the AA going directly to vociemail and MWI not on when a message is left.
For phones outside this range of numbers, AA transfer works fine and MWI works.
anyone ran into this issue before?
thank in advance.

Hi,
The range in which you are facing issue is XXX-XXX-0120 to XXX-XXX-0130, just try to open any one of the extension in this range and go to edit -- transfer rules -- standard/alternate (if alternate is enabled) -- Transfer calls -- may be this is set to Greetings. If so the transferred call goes to voicemail directly. Try enabling Extension.
Just try this for one extension and see...
Hope this helps, i had the same issue.
Regards
Jagadish G

Unity 7 Voice Mail Message Details

Just wondering if there is a tag in the message that a Unity Administrator can retrieve in order to find out if the message was delivered with an Automated FWD with a future date and time.
We had one user reported that they received an old test message that they sent themsleves from a long time ago but just came up in their inbox. I'm assuming they put a delivery time stamp to reflect a future date and time but they don't remember.
Thanks,
J

So for the 2nd scenerio you would want to check what your Message Subjects were set to. For Unity 7 open Web SA, click Configuration and then Message Subjects. Make sure that the Outside Caller Message has %CALLERID% in it somewhere. The value %CALLERNAME% will return unknown if we do not receive a name from the PSTN.
Try setting the Outside Caller Message to:
%U% %P% Voice Message from %CALLERID%
and that should get you your desired results.
The default Message subject is:
%U% %P% Voice Message from %CALLERNAME% (%CALLERID%). So with that it would say Voice Message fom Unknown (xxxx) if it was not able to determine the name of the user which is usually normal from a PSTN call.
Just to note, the From address is always going to say from Unity Messaging System, it will only be the subject that has the extension in it.
Bryan

Jabber for Windows and Unity Connection Voice mail out of sync

Hello all,
Now that Jabber is pretty much part of every install you begin to notice some trends. One trend that I have noticed happening across several of customers is complaints about Jabber and the Voicemail server getting out of sync. It’s never really been a wide spread issue but it has be noticed by several of my customers enough so that I’m reaching out to see if others are experiencing the same problem. Here are the symptoms, a person sitting at their desk they have a physical phone, and a windows PC running Jabber 4 Windows. They miss a call and the MWI lamp gets lit on the phone but not on Jabber. When you click on HELP / Show Connection status, you see all green checks, and Voicemail shows connected from Jabbers standpoint. When you exit the application and come back in, then it sync’s back up just fine. I have never seen it happen myself, but to be honest I’m never at my desk enough to even notice if my phone lamp is lit.
Anyway has anyone had similar issues? If so is there a fix?

Symptom:
User logged in Jabber and do not log-off/sign-out for more than 24 hours and then jabber does not receive new voicemails from Unity Connection. User will be able to receive voicemails from other interfaces like Outlook, TUI but voicemails will not show up in Jabber.
Conditions:
User does not sign out from jabber for more than 24 hours since last log on.
Workaround:
Sign out from jabber at-least once a day and sign-in back so that subscription will not expire in Unity Connection database.
Voicemail does not sync if Jabber left logged in for more than 24 hours
CSCuo46274
Can be fixed, depends on releases, TAC offered me a fix in version 10.5(1)ES29

Voice Mail Greeting Issue

I cannot reset my outgoing message. I'll record a new one and play it back, but when I call my phone from someone else's they get the old greeting.

Voicemail is a wireless carrier function. call them and ask.

Cisco Unity Express 8.6.6 Voice Mail not deleting when e-mail with attachment deleted

I have a Cisco Unity Communications Manager rel 9.1.2 that supports a remote location with a Unity Express rel 8.6.6 voice mail service module in the voice gateway to insure if WAN goes down the location still has voice mail. We have Voice Mail to E-Mail working. The problem is that when the e-mail with the voice mail is deleted the message stays in the Unity Express Voice Mail Box. All of our local users on the same Call Manager Cluster using a local Unity Connection Cluster rel 9.1.2 have the voicemails deleted when the e-mail is deleted.
How can I resolve this issue?

Found another post that referenced Cisco Bug ID CSCti37610.
CUC plays message is from Unity Connection Messaging system
Symptom:Before message playback, Unity Connection plays the message is from Unity Connection Messaging System instead sender's ANI
Conditions:Problem was observed on Unity Connection cluster and appropriate services are not rebooted after changing the SMTP domain name
Workaround:
Restart the Unity Connection servers
It should have been fixed in 8.5 but we did change the SMTP domain name on 8.6 and now see the problem. Will schedule a reboot and see if the issue goes away.

Callmanager, Unity Issue with Voice Mail

Hello Guys,
I am currently facing an issue with a Callmanager <-> Unity integration.
The situation is the following one:
All user own a voice mail box. User A forwarded its phone to his voice mailbox. User B forwarded its phone to User A.
If now User C calls User B, he gets forwarded to User A , of course. But if user A does not take the call, User C hears the voice mailbox from User B.
I would like to have for a special situation that User C hears the voice mailbox of User A.
Is this possible?
Thanks!

Hi there,
You can have a look into this setting which is available in Unity Connection 7.x ;
Via
Cisco Unity Connection Administration
Advanced (towards the bottom of the page)
Conversation Configuration
**Use Last (Rather than First) Redirecting Number for Routing Incoming Call**
You would need to think about what impact this might have on your setup, but it does allow
for users to Forward to their personal VM at times and the Helpdesk mesage when necessary
Hope this helps!
Rob

Unity Express - Incoming calls wont get voice mail

CUE works fine with telephones on my local network. Incoming and outgoing calls work fine.
However when I get an incoming call via SIP trunk the call will not get forwarded to unity express after 10 seconds. The line goes dead.
I searched for another post which suggested the following commands:
telephony-service
call-forward pattern .T
voice service voip
allow connections from h323 to sip
I've double checked them and there's still something wrong.
Here's my current configuration:
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
voice class codec 1
codec preference 1 g711ulaw
codec preference 2 g711alaw
telephony-service
load 7910 P00403020214
load 7960-7940 P00305000301
max-ephones 24
max-dn 24
ip source-address 192.168.20.1 port 2000
auto assign 1 to 24
system message Comtek
voicemail 3000
max-conferences 8 gain -6
call-forward pattern .T
moh music-on-hold.au
time-webedit
transfer-system full-consult
transfer-pattern 2...
transfer-pattern 3...
directory last-name-first
directory entry 2 2001 name Phone Two 7912
directory entry 3 2000 name Phone One 7970
ephone-dn 1 dual-line
number 2000 secondary 441833000000
call-forward busy 3000
call-forward noan 3000 timeout 10
no huntstop
ephone 1
no multicast-moh
device-security-mode none
mac-address 0017.0EF0.3642
type 7970
button 1:1
So pros, any suggestions?
Thanks

I made a new dial-peer to handle incoming calls as follows.
dial-peer voice 1000 voip
description Incoming SIP
translation-profile incoming SIPin
voice-class codec 1
session protocol sipv2
incoming called-number .T
dtmf-relay rtp-nte
no vad
The translation-profile puts the call through to my 2000 extension.
This is my "show call active voice brief" when an external incoming call is ringing through to my 2000 ephone-dn.
To me this seems to show the dial-peer "1000" matching and using the g711ulaw codec
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
1715 : 552 596706500ms.1 +-1 pid:1000 Answer +441833696807 connecting
dur 00:00:00 tx:0/0 rx:0/0
IP 87.127.240.98:16188 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1715 : 553 596706510ms.1 +-1 pid:20001 Originate 2000 connecting
dur 00:00:00 tx:0/0 rx:0/0
Tele 50/0/1 (553) [50/0/1.0] tx:0/0/0ms None noise:0 acom:0 i/0:0/0 dBm
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
This is the "show call active voice brief" for an external incoming call when the call is established.
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
1731 : 569 597220040ms.1 +3730 pid:1000 Answer +441833696807 active
dur 00:00:02 tx:105/16800 rx:104/16640
IP 87.127.240.98:15162 SRTP: off rtt:0ms pl:0/0ms lost:0/0/0 delay:0/0/0ms g711ulaw TextRelay: off
media inactive detected:n media contrl rcvd:n/a timestamp:n/a
long duration call detected:n long duration call duration:n/a timestamp:n/a
1731 : 570 597220060ms.1 +3700 pid:20001 Originate 2000 active
dur 00:00:02 tx:0/0 rx:105/16800
Tele 50/0/1 (570) [50/0/1.0] tx:16180/16180/0ms g711ulaw noise:0 acom:0 i/0:0/0 dBm
Telephony call-legs: 1
SIP call-legs: 1
H323 call-legs: 0
Call agent controlled call-legs: 0
SCCP call-legs: 0
Multicast call-legs: 0
Total call-legs: 2
Not too sure where to go from here.

Unity Express: More than one phone / DN with a voice mail box

I'm running Unity Express 8.0.2.
Is there a way to associate two extensions on separate phones, with one voicemail box?

Hi
From memory, you can add the second extension number as the "Primary E.164 number" on the user associated with the voicemail box.
That way both phones should be associated with the same VM box.
HTH. Barry

Voice mail and Embedded-Service-Engine0/0 issue

Recently I added PSTN and SCUE-ISM-8.6-K9 to be applay (IVR and Voicemail) on my Cisco Router 2921 ,
The PSTN now is working properly ,But I facing three issue of the voicemail ,Embedded-service Engine and IVR configuration as the following:
1- I recieved the following error message when enable the Embedded-Service-Engine0/0
"Memory size does not meet the requirements of Embedded-Service-Engine0/0"
Cisco CISCO2921/K9 (revision 1.0) with 479232K/45056K bytes of memory.
Processor board ID FCZ162670HW
4 Gigabit Ethernet interfaces
2 terminal lines
1 Virtual Private Network (VPN) Module
2 Voice FXO interfaces
1 Internal Services Module (ISM) with Services Ready Engine (SRE)
Cisco Unity Express 8.6.6 in slot/sub-slot 0/0
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
2- Kindly the attached file of the Voice mail configuration but not working.
3- Please, can you provide of a document about IVR configuration ?

Hello Ammar,
As per the error you required more memory for ESE module to work, you have only 512MB memory. Now I assuem you configured on Service-Module right ? It will work fine without any issue.
Next for your voicemail not working can verify that you have configured the SIP dial-peer to reach the Voicemail tiggered phonenumber i.e. 700 in your case.
dial-peer voice 101 voip
session protocol sipv2
session target ipv4:192.168.130.101
destination-pattern 700
Thanks
Selva

Jabber for Windows client Voice Mail issue

hi, cisco guys
    i have a collaboration test for my customer in resent days.
    the follow picture is the topo of my test system
   1. cucm1 use ICT non-GK trunk to connected with cucm2 and the ip phones with dn 56xx registered on cm1
    the iphones and jabber clients with dn 54xx registered on cm2
   2. cm2 intergrated with Unity Connection server and Cups server
       the version of cm1 and cm2 and unity connection is 8.6.2-21900
      the version of cups is 8.6.4
3. the issue occurrenced when the ip phone user 5412 call to 5411 but no answered, user 5412 sent a
      voice mail to user 5411，only MVI of the ip phone 9951 with dn 5411 turned on but jabber client wihtout any prompt message
      but when the user 5665 which registered on cm1 called user 5411 and sent a voice mail , status in normal,
      mvi turned on , the jabber client also can recived the prompt message and the the vocie mail could be played on the jabber client
      what's the issue probably be caused by & how can i solve it
      need your help!!!!

I don't know if you have a specific subnets permitted in the CUPS ACL
This is dangerous and incorrect guidence. The Incoming ACL allows the addresses defined to bypass authentication. In other words, I could impersonate your CEO if I wanted to. There are only two common use cases where doing this is appropriate: 1) the CUxAC server IP; or 2) older versions of CCX where CAD didn't support DIGEST authentication.
As for the original question: your English is difficult to understand. Is the following problem statement accurate?
When 5412 on CM2 leaves a voicemail for 5411 on CM2, the MWI is lit for 5411 but Jabber does not reflect the waiting message?
If this is accurate, is the message also shown in the Web Inbox? https:///inbox
The serverIP should be the CUC server defined in the voicemail profile on CUPS for the user who owns 5411.
Please remember to rate helpful responses and identify helpful or correct answers.

Unity Express voice mail timing issue.

Similar Messages

Maybe you are looking for