Universal plug and play for iMac

I'm presently using TVMOBiLIi (Universal plug n play) and T Link extenders to enable our iMac (upstairs) to stream to our Sony Bravia TV (downstairs) enabling access to the internet via cat 5 network cable.  Mainly used to watch iPlayer on our telly.
We keep getting alerts for TVMOBiLi to say our streaming limit has been capped. How do others stream without problems? Do you use another universal plug n play software?

Thank you for taking the time to reply.  The ISP isn't limiting the bandwidth as I can still access the internet,  The message is from TVMOBiLIi within the TVMOBiLIi screen but I can still access iPlayer anyway.  I was hoping to find a recommendation for another upnp, also have EyeConnect.  It doesn't seem Windows users have this kind of problem.

Similar Messages

  • Re: NB200 - Automatic plug and play for Ethernet cable

    Do you know why I do not have automatic plug and play when I connect an ethernet cable for internet on my NB200?

    Hey mate,
    Which automatic configuration you mean exactly?
    Normally nothing is plug and play. If you want an Internet connection via Ethernet cable you have configure this port. That means you have to set a static IP address for example or DHCP.

  • Universal plug and play

    Does the air extreme has UPnp? (Universal Plug 'n Play)?

    Apple's corresponding setting for UpnP translates to NAT-PMP.  This is a Port Mapping Protocol that allows you to assign the port values that you need.
    You might want to review the User Tip from forum expert Tesserax on this, depending on which version of AirPort Utility that you might be using:
                     AirPort - Port Mapping Basics using AirPort Utility v6.x
                     AirPort - Port Mapping Basics using AirPort Utility v5.x

  • Plug and Play for Cisco Small Business 300 Series Managed Switch

    Good day
    what are the Auto-Install options available for the Cisco Small Business 300 Series Managed Switch ?
    It would appear there are none, the operating system is not the standard IOS I'm used to.
    Would like to use it with Cisco Prime Infrastructure's PnP Gateway capability.
    Regards
    Pierre

    Prime Infrastructure uses and assumes a CNS (Cisco Network Services) agent on the other side when enabling "plug & play". 300/500 Series do not run IOS and does not include a CNS agent, but there is a way to enable auto-configuration. The switches support DHCP Autoconfiguration (using DHCP options 66, 67, and others) whereby they automatically download their config from a TFTP server at boot time. This allows an administrator to put the configs for all the switches on a TFTP server and simply boot a factory-defaulted switch in order to get its config.
    Attached is a document showing how this is done.
    Hope the information would be of assistance.

  • Airport Extreme Universal Plug and Play

    Hello,
    I recently spoke to my service provider. They told me my Airport Extreme is vulnerable to UPnP. However, apple doesn't have UPnP.
    You can use this website to check:
    http://upnp-check.rapid7.com/
    What can I do about this?
    Thanks.

    You are safe .. there is some false reading that the ISP is getting.. if they are sending you a message.. please post the exact message as several posts are here about them.. and mostly you just need to get the ISP to stop sending them.

  • How do I set MacBook to an external display when the plug and play doesn't recognize it?  I am trying to set my Samsung 530 LCD as a monitor but HDMI and VGA cords (and the adaptor for them) doesn't seem to work.

    I have tried everything I can find on line but they all claim that the plug and play works, and they don't for me.  I tried the mini dvi to HDMI and a HDMI cord and that was not recognized no matter which unit I rebooted first.  I found someone who said that my Macbook might be too old for the HDMI technology so I returned the cords and went to the VGA cord and adaptor.
    I tried this first with the HDMI setup:
    http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx= 167919&modelname=LN40C650L1F&modelcode=&session_id=NDhJrD0DQT0Z8KRsm62yhxJxqnyPy SKhlhpB8vQ6h9Q7R2BZJGzj!-1089109758!1761676444!7501!-1!434477884!1761676348!7501 !-1!1292098185857
    Then I tried this with the VGA setup:
    http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx= 167901&modelname=LN40C650L1F&modelcode=&session_id=NDhJrD0DQT0Z8KRsm62yhxJxqnyPy SKhlhpB8vQ6h9Q7R2BZJGzj!-1089109758!1761676444!7501!-1!434477884!1761676348!7501 !-1!1292098185857
    I contacted Samsung support and they said I needed to set the display settings to external display on the mac.  I went to the display settings and moved the icon to my status bar.  When I click on search for displays or whatever it says (I'm not at my Mac right now) it does nothing.
    What am I missing?

    I am using MAC OSx 10.5.8 (9L31a) as my operation system.  The TV says "No signal.  Check connected device's power, cable connection and source selection."  Seems to me that that goes in hand with what the Samsung tech said about the Mac needing to be forces to use the external display.  But how do I do that?

  • I have a new iPad Air. Can I use plug in USB camera reader to have a load of movies etc on an external hard drive and then plug and play so to speak. I'm off on holiday and haven't got the capacity to have everything on that I'd like for the kids

    Can I use a plug in USB camera reader to have a load of movies etc on an external hard drive and then plug and play so to speak? I'm off on holiday and haven't got the capacity on the iPad to have everything on that I'd like for the kids.
    So basically I want a hard drive with X amount of films etc on. Can I then watch them on my iPad?
    Hope this makes sense.

    External HDD won't work.
    You need something like this:
    http://www.seagate.com/goflexsatellite/

  • My classics IPOD has died over the weekend and I plan to but an IPOD Touch -- but need to to 'work' and simply sync all my 'old' music on a plug and play basis -- or is that wishful thinking ? I need it urgently for a holiday so only time to buy it n run

    Any advice on :
    1. The Touch as a product
    2. The likely chances of plug and play resync to new device without hours of 'fiddling' / support calls
    or I can just use my Shuffle I guess ----

    There should be no problems, make sure to have all the needed software updates for Windows and the new iTunes 10.5 installed before connecting your iPod touch.
    You already know how the basic sync process is working, there are a few more features added like mail for example: iOS: Syncing with iTunes

  • Help file for the Plug and Play driver of Agilent Technologies E5071C

    I just download the Plug and Play driver of Agilent Technologies E5071C from the below link:
    http://sine.ni.com/apps/utf8/niid_web_display.model_page?p_model_id=5692
    I find that there is only some examples and not any help file with detail description for each input of those VIs. Although there is brief description for each VI when I press "Ctrl+H" on the VI,I still can't figure out how to use this driver. :-(
    Is there any help files with more detail description?
    Or any related examples for my reference? I hope to measure the S11 and S21 of the SMA cables

    The driver implements the commands defined by agilent.
    So look in the agilent programmers manual to find the meaning and how to handle the instrument.
    greetings from the Netherlands

  • Is the 595759-001 DVD burner for Elitebook 8540p plug and play

    I have a DVD ROM player, only, in my Elitebook 8540P, and I just ordered a DVD writer (595759-001) to replace it with. Do I just install the hardware? Is this going to be a plug and play experience, or do I need to locate drivers for the replacement? Do I need to uninstall the driver for the original DVD ROM? 

    Hi, The driver for any optical drive is provided by Windows, so you should just have to connect the new device, however it can sometimes avoid any issue by doing this as follows. Hold down the Windows key and press R.  Into the Run box type devmgmt.msc and hit enter.  Expand DVD/CD=ROM drives, right click the existing device and select Uninstall. When done, shutdown the notebook and fit the new optical drive. When you then boot Windows, give it a few minutes to fully load and you should find the new drive is up and running. Regards, DP-K

  • Apple plug-and-play driver for AOC monitor

    I just purchased a new 23" AOC monitor to "clamshell" with my macbook. I have purchased the appropriate cables to connect with my macbook to discover that the monitor software doesnt have a mac driver and the AOC website says to download a Mac Plug and Play driver to work with the monitor. The monitor turns on but mirrors my macbook and jumbles up my desktop. I am unable to locate one of these "drivers" with apple's help. Is anyone familiar with this issue that might be able to recommend a solution? I would hate to take my brand new monitor back.

    I just got my new MacBook 15 the other day and today decided to set it up wiht my AOC E2251Swdn monitor.  Black monitor screen.  Grrrr.  It worked fine with my old laptop (mid 2007).  I got the mini dv adapter as I saw it didn't have the DVI port I'm used to seeing.  However, the monitor when I got it only came with the old school VGA cord, not a DVI, thank goodness I finally had a use for the one that must have originally come with the previous laptop, and that worked just fine.  Right now I have the VGA cable with the DVI apple adapter then plugged into the DVI to Thunderbolt adapter.  Could this cord issue be why my monitor claims no signal no matter what I do?
    Also, when I looked for drivers and click the link in the post above, it downloads a folder for drivers, however, I dont' know what to do with the files in that folder (2251w.cat, 2251w.icm and 2251w.INF).  I have a hunch they are windows only. 
    If I need to get a strictly DVI cable I can do that, but would like to know if that's likely my problem before I buy it.  The monitor is only about 2 months old give or take. 
    Thank you in advance

  • How can I configure and control a non-plug and play VXI card using the NI-controller (NI-VXI/NI-VISA software)?

    Defining the slot, logical address and sending data across the card bus are the main operations I would like to perform. The non plug&play card is a VXI send & receive slave card. Low-level programming is probably required. Has anyone tried this before? If so I would be so grateful if you could share your experiences or refer me to someone who has.
    Thank you for your time and help,
    Nandeesh

    VXI cards are, by specification, plug and play, so I'm not exactly sure what you mean by a "non plug&play card." I'm guessing that the card is effectively a VME card. In this case, you can just add the VME device in the proper configuration utility. Here is a link to a document on our website about configuring VME cards (http://ni.com/support/vxi/vmeinfo.pdf).
    You should easily be able set the slot, pseudo Logical Address and memory space. Once configured, you should be able to write to registers using NI-VISA commands (viIn, viOut, and viMove). These high level commands are included in the highreg.c example which shipped with your NI-VISA software (installed in vxipnp directory).
    I hope this helps.
    Trey Hamilton
    National Instruments
    Applications Enginee
    ring
    http://www.ni.com/support

  • Seagate Plug and Play from Macbook Pro to Macbook Air

    Recently bought a new Macbook Air to upgrade my 2010 Macbook Pro 13 inch.
    I had been using a Seagate Plug and Play external hardrive that needed no formatting on my Macbook Pro . However when I tried to use the same on my Macbook Air it did not allow me to drag files across the the hardrive.
    I can see it in the Finder but unable to drag files to it.
    I thought Plug and Play woudl across all Macs?

    OS X comes with the ability to read NTFS but not write it. Some Seagate drives come with software to enable writing NTFS on that drive. You probably installed it on your 2010 MBP when you got the drive, then forgot you had done so. Find the software installer if it is still on the drive and run it on your MBA. (You might have to locate a newer version online.)
    Alternatively, you can purchase a version that can run on any NTFS disk. I use Paragon NTFS for Mac. I initially got a limited version with a Seagate drive, then purchased the full version.

  • I have a Keyrig 49 m-audio and it is not recognize by OS 10.9.4 when it says that mavericks is plug and play. I would really like to do what I am able to do on earlier version of OS... Please help

    I have a Keyrig 49 m-audio and it is not recognize by OS 10.9.4 when it says that mavericks is plug and play. I would really like to do what I am able to do on earlier version of OS... Please help

    it the link it seem someone made it work. How can a new OS make things more difficult... it seem crazy too me.
      via: http://community.m-audio.com/m-audio/topics/m_audio_keystation_with_osx_maverick s_9_1_doesnt_work_via_plug_n_play
    pavery85   8 months ago
    **UPDATE*** All is working on Mavericks 10.9.1 for me!! Back in business!
    Drivers seem to working now!

  • How to create plug and play design pattern on a environment

    Hi All,
    Help me to get a best design for my problem statement.
    Problem Statement: I have to create a platform where I should be able to plug and play different components. explaining better with example
    Example:
    1. I have to create a platform for school
    2. In this school platform we have to plug in multiple components like "Student", "Teacher", "Subjects", "ClassPeriods" etc.,
    3. These components should be easily plug/unplug and play
    4. Like, the component "ClassPeriods" want to purchase from Vendor 1 and plug it to "School" platform it should work.
    5. Incase if we want to unplug the "ClassPeriod" component provided bfy Vendor 1 from "School" platform and want to plug the "ClassPeriod" from Vendor 2. then the Design should support without any extra effort.
    Suggest me the best design pattern for the problem
    This design pattern is for ASP.Net
    Thanks,
    S.Kannan

    Sounds like you're looking at 'Composition'. As a background, and possible solution, take a look at MEF;
    http://mef.codeplex.com/
    http://pauliom.wordpress.com

Maybe you are looking for

  • What network audio sounds systems (e.g. Sonos) are recommended to work well with Macs?

    I'm looking to replace my audiophile stereo system with a network audio system at home.  Had NAD components with English Epos hand-made speakers that sounded great, but very immobile.  I need speakers in each room of the house that can be networked,

  • Creative Cloud Shows Multiple Versions - Why?

    I've been running Photoshop and Lightroom via Creative Cloud since January on Mavericks.  Updates are offered once in a while and I accept to keep up to date.  What I don't understand though, is why CC on the menu bar lists 'Photoshop CC' and 'Photos

  • Why doesn't iPhoto allow dragging multiple items?

    The last few versions of iPhoto (maybe since installing Mavericks) do not have to ability to drag and drop multiple items. I can highlight multiple items, but if I want to drag photos into folders to organize them, I have to drag them ONE AT A TIME!

  • Can't see ANY of my Match/Cloud items

    I have just authorized my work computer in iTunes and signed into iTunes match.  It says that I am signed in and have over 7000K songs availabe but I don't see ANY of them -- no listings whatsoever. Thoughts?

  • Who wants Duke Dollars?

    I have a program with a problem no one has helped me solve yet. And it's stupidly simple. me ?? stupid? maybe. I want to make a directory on a server if it doesn't exist, using sun.net.ftp. Who can help me?