Universal WorkGroup Bridge (uWGB) support dropped for 1130AG?
why Cisco dropped support for this in 1130AG model?
What was the last version of IOS that supported it?
Hi David,
what makes you say that the support for that got dropped ?
I have a 1130 on my desk running 12.4.25 and it definitely can be configured for universal WGB ...
This said, it's a bet strange to configure a ceiling-mountable AP for uWGB but you probably have your reasons :-)
Nicolas
===
Don't forget to rate answers that you find useful
Similar Messages
-
Why was Extension Manager support dropped for Bridge?
Title says it all. Adobe Extension Manager supported Bridge in CS4, CS5 and CS5.5 and now it doesn't. From what I understand, the simple addition of the "configuration" folder and the files it contains from a CS5.5 installation suddenly makes it work, so my question is: why was this dropped for CS6? Is there more to it?
...MikeHi David,
what makes you say that the support for that got dropped ?
I have a 1130 on my desk running 12.4.25 and it definitely can be configured for universal WGB ...
This said, it's a bet strange to configure a ceiling-mountable AP for uWGB but you probably have your reasons :-)
Nicolas
===
Don't forget to rate answers that you find useful -
Windows 7 support dropped for Mac Pro 2013
I have sent feedback to Apple already as I understand from the support page Windows 7 x64 support has been dropped for the new Mac Pro.
Bearing in mind the corporate workstation market has largely shunned Windows 8/8.1 I find the dropping of support inexplicable and plain daft to enable the Mac Pro to take market share from the windows hardware domain.
My clients have purchased two Mac Pro's on launch day on the prerequisite that they can run Windows 7 with the possibility of more orders after the new year once testing is complete. Unless it can be made to work using EFI boot which as I suspect is the reason support and can easily be worked around you lose in my case 2 orders with the possibility if 10/20 more after. No workaround will mean cancelled orders.
Hopefully if enough of us air our disappointment Apple will reconsider because they will lose a sizeable chunk of sales because of this near sighted policy.If what you say is true, then it would be a question of hardware support capabilities in Win 7, not a near-sighted policy. In any event, these are user forums. You aren't speaking to Apple, so I suggest you speak to Apple. Don't complain here. It's inappropriate and violates the Terms of Use.
-
1602 AP - Workgroup Bridge Cannot Associate to Parent AP
Hi All,
For a few weeks now, I have been trying to connect a Cisco 1602 standalone AP to our unified wireless network as a workgroup bridge. Eventually this AP is to be moved to another wireless network where I will need it to run in universal workgroup bridge mode (for non Cisco wireless networks), so I just want to get this working in the office before I take it elsewhere and try to get that to work, as the configuration will be similar.
So far I've been unable to get this 1602 AP to associate to our network. The particular SSID I'm trying to set up is a BYO style SSID, normally if you connect a device you provide your Active Directory username / password and your laptop / phone / whatever connects. I know the username is fine because if I use it on another device it's not a problem.
The AP keeps repeating this message: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating. Cisco.com tells me that this is to do with MFP, however I've changed a number of MFP settings in the SSID and this seems to have made no difference.
I'm thinking this is a problem with authentication or association. I have a question, why do I need to input Radius server information into the config (eap_methods)? When you connect a regular device to this SSID it doesn't require any Radius server settings in order to connect, I don't understand why the AP needs these settings. Also, when authenticating to AD, do you need to include the domain name as part of the username?
Wireless isn't my strong point unfortunately. Is anyone able to help with this? Config and log is below. Many thanks.
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname WGB-AP
logging buffered 10000
logging rate-limit console 9
enable secret 5 xxxx
aaa new-model
aaa user profile userprofilename
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
no ip routing
no ip cef
dot11 syslog
dot11 ssid BYO
authentication open eap eap_methods
authentication shared eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
infrastructure-ssid
ids mfp client optional
eap profile EAPTLS
method mschapv2
method peap
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-88743315
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-88743315
revocation-check none
rsakeypair TP-self-signed-88743315
crypto pki trustpoint WGB-PEAP
enrollment terminal
subject-name CN=username
revocation-check none
rsakeypair manual-keys 1024
crypto pki certificate chain TP-self-signed-88743315
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 38383734 33333135 301E170D 39333033 30313030 30383234
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D383837 34333331
3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100BB10
F5361E52 A573FE8A 247142AD CF53D762 38F7BB42 7E723B2B 5C78100E 7F312442
3BE63A8B 7E826758 3F2914D0 4BBC93A6 CCACA795 927514E7 74561589 444D03BA
C20B80D8 85E52A18 C3B287BF 4A1EEF83 B43DD673 12BF075F 7CA038C0 C31F1FB4
F75C3F86 C09DC703 FB05676B 16B86754 F0F11D4D 36B61F81 DF15C02A 9C410203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14999B3B 7F4B10FA B95CC90B D7218636 39280AFE 4E301D06 03551D0E
04160414 999B3B7F 4B10FAB9 5CC90BD7 21863639 280AFE4E 300D0609 2A864886
F70D0101 05050003 81810076 27E215C4 C105C66D 15124645 D3F4A538 F977A95F
7AF0FF05 648D41A4 A796F9CB CC6327FF 726DA1D6 290CD438 C2111DF8 208B92B5
63B09FEC 1CA334F7 A4607E71 18EBCB44 0A175BEE 30689849 B4D9222E 7EB1C1DB
F36BDDD3 3F5514A6 8A006A8A A113A44D 7337B6D8 7860AA25 EBAD5588 8543DF88
9E6A3D62 6E875372 277B57
quit
crypto pki certificate chain WGB-PEAP
dot1x credentials MyCreds
username DOMAIN\AD-USER
password AD Password
username Cisco password 7 00271A150754
username DOMAIN\AD-USER
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid BYO
antenna gain 0
stbc
beamform ofdm
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm tkip
ssid BYO
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
no ip address
no ip route-cache
ip forward-protocol nd
no ip http server
ip http authentication local
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host xxxx auth-port 1812 key 7 xxxx
radius-server vsa send accounting
bridge 1 route ip
line con 0
logging synchronous
line vty 0 4
transport input all
end
Jan 5 14:34:30.636: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:23.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:42.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:38:19.833: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:39:33.901: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:40:49.948: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:42:10.123: %SYS-5-CONFIG_I: Configured from console by console
Jan 5 14:42:42.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
Jan 5 14:42:46.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:43:06.058: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:45:18.173: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: AssociatingWith PEAP there is a certificate being used on the radius server for securing the first phase (outer tunnel). In this scenario the access-point acts like a dot1x client, so like any other client it has to validate the certificate the radius server uses. Therefor the root certificate (and intermediates, if being used) needs to be installed on the access-point.
I never configured an WGB in this way, so I fired on my lab to see if I could get it to work. Sadly I did not manage to get it to work properly, I'm running into "EAP session timed out" messages in ACS (my radius server). I did also ran into the MFP issue, but as long as you configure MFP as optional on the network side, it should work. Because of the CCIE exam, I'm running old AirOS software on the WLC and also the software on the access-point I tested this configuration on (2600) is not that new. So it could be that I ran into a bug testing this, so I would advise you to run the latest software on your 1600. There are WGB related bugs fixed not so long ago. This configuration is supported since IOS 15.2.2(JA) and higher.
If I look at your configuration you still need to actually install the certificate, the trustpoint is empty. Besides that the following configuration changes needs to be made:
eap profile EAPTLS
no method mschapv2
method peap
dot11 ssid BYO
authentication open eap PEAP
no authentication shared eap eap_methods
authentication network-eap PEAP
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
no infrastructure-ssid
no ids mfp client optional
For more information look at this document. -
HT4942 my iwork says it no longer supports drag & drop for excel... why?
my iwork says it no longer supports drag & drop for excel... why?
'''Swarnava''', I do believe he has already been downloading and installing Firefox 9.0.1 three times already.
'''avowedrep''', your user agent appears as if it is Firefox 3.5.19 in more system details link on right of your post.
Mozilla/5.0 (Macintosh; U; Intel Mac OS X 10.6; en-US; rv:1.9.1.19) Gecko/20110420 Firefox/3.5.19
See this on how to reset to default.
https://support.mozilla.com/en-US/kb/websites+or+add-ons+incorrectly+report+incompatible+browser#w_reset-your-user-agent
As for the ''"Warning: this version of firefox is no longer supported?"'' is sounds as if you still have the old http://www.google.com/firefox Firefox start page hosted by Google as your homepage. This old default homepage is no longer used (Firefox 3.6.* and earlier) as '''about:home''' has been in use since Firefox 4.0
Either ignore the "You're not on the latest version of Firefox" message, change homepage to '''about:hom'''e, change it to another page or leave blank.
http://support.mozilla.org/en-US/kb/How+to+set+the+home+page -
Has anyone setup a Workgroup Bridge on a remote H-REAP site and got it working? I have the AP associated to the controller but the AP cannot ping the controller and the controller cannot see the wired clients on the AP.
Hello, yes we current have many WGB's connected to FlexConnect LAP's. Support for connecting to FlexConnect LAP's (formerly H-REAP) has been added in WLC Code 7.3. Please refer to release notes: http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn73.html
Thank you. -
I am trying to install windows 7 on my macbook pro 13", when i run bootcamp it tells me that there is not a windows support software available for my computer. Where can i get the windows support software for my macbook?
Apple only supports Windows on certain hardware.
http://www.apple.com/support/bootcamp/
Apple provides their framework for Windows to run on a Mac, a piece of software called a Hybrid MBR that bridges the gap between how Windows reads the drive partition table (MBR) and EFI/GUID partition table that Mac's use.
It doesn't mean Windows can't run on your Mac, a third party solution called rEFIt will also bridge the gap and allow booting of more that just Windows, Linux as well for a triple booting computer.
Your hardware has to meet the other requirements the second and third operating system needs as as being able to install drivers that will work for your hardware, especially the fans or they will run loud and fast by default.
http://refit.sourceforge.net/
This above is a advanced procedure which requires knowledge how computers and various operating systems, drive formats and so forth work.
I even admit I don't know everything myself, but I experiment on a separate piece of Mac hardware (out of warranty/AppleCare) designed for this purpose so in case something screws up I'm not taking down my only machine and can use the other to get online and find solutions.
There is a very high potential for losing your data if your using advanced/non-Apple methods to install Windows on your only Mac where Apple doesn't support it. Also one shouldn't be doing this on Mac hardware that is under AppleCare or warranty as it might be voided. Proceed at your own risk and education. -
Cisco AP1121G Workgroup Bridge Problem
Hello,
For reference I have attached the following:
Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
I am seeking assistance with the following problem.
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction.
Also attached is a result table of ping attempts through the ap1121wgb from each side.
I don't have a problem with the wireless connections. The ap1121g's associate ok.
Based on the ping results the problem appears to be in the ap1121g-wgb configuration, but I have run out of ideas.
The following two cisco documents have been my main reference, besides the cisco command lookup site.
http://www.cisco.com/en/US/customer/products/hw/wireless/ps430/products_configuration_example09186a00805b9b87.shtml
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap19-wgb-standby.pdf
Any insight will be greatly appreciated.
Thanks...Robert,
Going back to your original post and looking through the example given in the first URL, I spotted a few lines in the example configurations which apply to older revisions of code, but not newer AP code, so they may be misleading. Based on the parameter availability of station-role workgroup-bridge in your last message, would you be wiling to try the following?
Reset both 1121 APs to factory default configuration (#write erase -- do not save config to startup if prompted)
Give each AP an IP address on BVI1 so that both APs are in the same subnet
Apply the following configuration to the infrastrucuture (root) AP:
dot11 ssid WGB-SSID
authentication open
interface dot11radio 0
ssid WGB-SSID
station-role root
no shutdown
Apply the following configuration to the workgroup-bridge (client) AP:
dot11 ssid WGB-SSID
authentication open
interface dot11radio 0
ssid WGB-SSID
station-role workgroup-bridge
no shutdown
The intended goal with this exercise is to get rid of all config and to try only basic required elements of a WGB configuration, starting with fresh factory defaults. Let's see if it will work for you as a bare-bones setup and then you can add other configuration like encryption and ACLs back in later.
Justin -
Using the 1262 AP in Workgroup Bridge Mode
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perfom this functions? I will put a Layer 3 switch on both ends to route traffice (3560C-8). Should I use the Yagi antenna's for outdoor use? Thanks!
You could go WGB, but root/non-root might work better. This will allows you to pass multiple VLAN across the link.
This is a bit old, but it' the Bridge Range utility
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps458/prod_technical_reference09186a00800a912a.xls
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
Can a Workgroup bridge 352 act as a LEAP client (supplicant) ?
Is it possible for a WGB in Version 8.84 to act as a LEAP client (supplicant) instead of the connected client NICs in the workgroup?
This question is as important as the workgroup could be composed of IP Cameras or other IP devices who could not act as a LEAP Client.
Thank you
JackyHi,
It is not so clear as it seems to be, because several CCO documents are introducing this LEAP ability of the WGB but none of them give details.
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_data_sheet09186a0080088833.html
"For authentication of devices attached to the workgroup, a username and password may be stored in the workgroup bridge in either static or dynamic memory. When authenticated, the workgroup bridge receives a single-session, single-user encryption key from the Remote Access Dial-In User Service (RADIUS) server via the associated AP. With this centralized and standards-based architecture, wireless security scales to meet the requirements of any enterprise."
AND
http://www.cisco.com/warp/customer/cc/pd/witc/ao1200ap/prodlit/wrsec_an.htm
"Figure 6: Workgroup Bridge Security Configuration"
What do you mean about ??
Jacky -
Workgroup Bridge and local Wifi Config
Hi all, hoping you can help me with this, just need an other brain as mine is empty as I've been staring at this for too long!!!
What I'm trying to config is to have a standalone local WLAN (Built into a VAN) running on the 2.4ghz and then also have a workgroup bridge on the 5ghz to the corporate lan.
Setup is this:
2960<-->1142(autonomous) <--Workgroup bridge on 5Ghz--> 1131(Lightweight)<3560>--<5508WLC> (hope that makes sense!!)
So far I have the bridge working, the 1142 connects to a ssid on the 1131 using psk. I can see the 1142 as an assosiated client on the wlc and I can ping the the lan from the 1142 so I'm happy the bridge is working.
Clients connected to the 2.4ghz ssid on the 1142 can only ping through as far as the AP(1142) I can't seem to get the traffic to pass across the bridge, is there something I need to do to link the 2.4 to the 5ghz bridge link?
Any help always appreciated, cheers.dmantill - Thanks for your link. I have read through and checked my config but my plan is to have a number of clients, all dhcp assigned, connecting to the do0 int for local wlan breakout.
I'm not sure that the passive config will help me there.
Steven - I have enabled the wgb on the do1 int and I am connecting clients on the do0 int for local wlan breakout. Enabling the WGB has not disabled the other radio on my setup.
I was running 7.0.98.0 but have today upgraded to 7.0.98.218 on my WLC but that has not helped.
From what I can tell it looks like my problem just lies with routing traffic across the 2 radios. My local clients can ping as far as the WGB and if I CLI into the WGB AP I can ping the corporate lan on the otherside of the bridge and can also ping from the lan to the WGB. I just cannot seem to get the 2 ssid's to route between each other.
Here's my WGB config, hope this brings some more ideas!!
Cheers,
Jason.
Current configuration : 1555 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX
logging rate-limit console 9
enable secret 5 $1$ujWI$HMYMAjMfJV2J2WaGa1/JJ0
no aaa new-model
dot11 syslog
dot11 ssid XXX
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 105A0C0A11001D1908
dot11 ssid XXX
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 080F15480C090D1221
username Cisco password 7 02250D480809
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
bridge 1 aging-time 216000
line con 0
line vty 0 4
login local
end -
Workgroup Bridge between WRVS440n and WAP321
Hi, i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.
First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference
I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
What am i missing?Hello Lars,
Just wanted to add a note to this as well. Pretty much the workgroup bridge is made to be used with other wireless devices that are not WAP121's and WAP321s. Cisco pretty much recommends to use WDS bridge if you have another WAP321 or WAP121.. if that is not the case then workgroup bridge is your other options. The admin guide should have some good documentation on this and also if you click on help in the GUI of the WAP321 it provides a lot of great information as well! It gives you recommended set up for this configuration.
Other than that you do not have to set up WDS on the WRVS4400n. As long as the SSID, wireless channel, wireless mode, wireless bandwidth and secuirty is the same on the WAP321 and the WRVS4400n this should work out just fine. Maybe have to power cycle the devices a couple times to get it to come up but I know I have gotten this to work between a RV220w and a WAP321... so I do not see why it shouldn't work between the WRVS4400n and the WAP321.
Hope that helps!
Thanks,
Clayton Sill -
Aironet 1242AG duel antenna Workgroup Bridge
I have an Aironet 1242 AG that I have configured as a mobile workgroup bridge. I have noticed when you enable the bridge on Radio0 (G) Radio1 (A) is disabled or cannot be configured as a bride on top. I read it several places in the documentation that it will do this but I haven't seen an explanation as to why. The 1242 is going to be moving throughout a building so if it is possible I need to find a way to configure it so that if Radio0 looses signal it will jump to Radio1 until Radio0 has a good signal again. I can't make any modifications to the stationary broadcasting access points but they are also 1242 access points. If anyone could tell me if this is possible and how to do it or why it is not possible I would be grateful.
Thanks,
MattEnabling the Hot standby activates both the Radio. But both the Radios will be activated at a time meaning communication happens simultaneously on both the Radios. One Radio will not act a s a backup Radio for the other.
-
Hi Team
Can anybody tell me if a 1522 (or, I guess 1510) Mesh bridge can support VLAN tagged packets? ie Multiple VLANs on either side of the bridge. Is anybody using this in production?
Also is anybody using this with wireless clients on the MAP also?
My aim is to get wireless clients onto one VLAN, some remote wired workstations onto either the wireless client VLAN or a separate VLAN, plus a VLAN for the AP IP address (AP-Manager).
Thanks
LPIt allows the LWAPP access points to communicate with the controller via a Layer 2 (L2) or Layer 3 (L3) network. For the further description of the Cisco Aironet 1522 Lightweight Outdoor Mesh Access Point follow the URL :
http://www.cisco.com/application/pdf/en/us/guest/netsol/ns107/c649/ccmigration_09186a0080775ae7.pdf -
Unreachable device behind a workgroup bridge
Hello,
we have a problem, that already occured at two locations:
We installed workgroup bridges (at one location a AP-1242AG connecting to an IOS-AP, at the other location a AP-1131AG connecting to a controller-based WLAN). Behind these workgroup bridges there are devices that talk very little by themselves (about one packet per hour).
So in the IOS-WLAN they are reachable only after pinging the device from the AP to which the WGB is connected. In the controller-based WLAN they are only reachable from the WGB itself, not from the rest of the LAN.
My suspicion is, that these devices disappear from the ARP-/Mac-Address-tables because of the little traffic they send. How can we work around this problem? Static ARP- and/or MAC-Entries? But where to place them, in the core, on the APs?
I would appreciate any help.
Thanks,
SebastianHere is the URL for the WLC configuration and troubleshooting guide which will help you :
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a0080810880.shtml
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_tech_note09186a0080811085.shtml
Maybe you are looking for
-
Hello all, I am looking to see how to create a page turning effect in Motion. I want to animate the pulling of a corner of a jpg from bottom right to centre left to resemble a book page turning. The image should also curve with the motion. Any ideas?
-
Numeric key pad is not working, card reader is not working
Numeric key pad is not working, card reader is not working,
-
There is insufficient system memory
I have 6 GB of ram,6GB swap space,i7 and a GTX480 1.5GB and I'm getting this error: There is insufficient system memory available to run textures with the highest quality.To enable you to play normally ,textures are used with lower quality. The game
-
HT201441 What if the previous owner to my new iPad is dead?
I just got a new iPad mini from a close family friend who died. I don't know the password, nor does anyone else. Is there some way I can completely wipe the iPad, including the iCloud account?
-
This one has me pulling my hair out. I have a file with pre stored data (sequentially written) now I want to pull the strings of data back into my program. Everytime I click the next-> button I have set up it seems to read the first string of data an