Unknown failure on TC and Airport Express

Hello there,
I've got some problems with connecting my TC and Airport express to extend my network.
Both show up in Airport Configuration program, but then give an "unknown failure, please try again" notice.
Tried is several times, but nothing works, even after a hard reset/factory reset.
Anybody got an idea?
Kind regards,
Angelo

I suggest that you back track a bit here when you say that you have problems with both the TC and AirPort Express (AX).
If you power off the AX, is the Time Capsule working correctly?
What version of AirPort Utility are you using to configure things?  If you are not sure, click the AirPort Utility menu in the upper left corner of the screen, then click on About AirPort Utility.
Please post back with the version number that you see there.

Similar Messages

  • Airport Extreme and Airport Express conflict and failure

    I spent 2.5 hours on the phone with Apple and still could not get my Airport Extreme and Airport Express to function. My Apple TV failed as well:
    * Connected AEX through Airport Utility to internet. Airport Utility replaced my old configuration on my LinkSystem router. Green light.
    * Checked Apple TV. No connection available. Unplugged cable modem, waited 1 minute and tried again. Apple TV connected. No problem.
    * Flashing amber light on Airport Express for Airtunes. Does not show up in wireless device list. I call Apple.
    * Reset Express. Still no signal. Connect via Ethernet cable. Reconfigure. Green Light. Music works.
    * Check internet connection, in order. Apple TV fails. No connection to server.
    * Apple TV reset. No connection. No wireless network found.
    * Reset Airport Express. Reconfigure channel specifications. No connection with ATV or Airport Express.
    * Disconnect Airport Express. Reconfigure. With ATV disconnected I get Airport Express back. Green light but this time no music. Remote speakers appear on itunes, but no music is transmitted.
    * Did a total wireless reset on Extreme, and now both Express and ATV are not working.
    Frustrated and dissapointed I disconnected everything put back my 5 year old Linksys router and within 15 seconds both ATV and Airport Express worked flawlessly.
    How can this happen? What is wrong with this device? It is my second one in a week. The first one made no wireless connection to my Mac at all.
    After sulking for hours I tried again, this time leaving the Express out of the equation and reconfiguring the ATV to take over airtunes. After a reset it did fine. Now I have a pure n signal running at 5hz. ATV works again. So does internet.
    Any suggestions? Is there something I did not try?
    I tried the Firewall trick, the accept all incoming connections trick, the disabling of the iv6 trick, the join a wireless connection trick, and everything else Apple Care could think of.

    Maybe I was not clear enough on my post and configurations,
    I had a Linksys before I purchased the airport extreme. My airport express joined the Linksys network for the purpose of airtunes. This worked flawlessly from day one.
    Airport Extreme asked in the utility to take over an existing network or replace a router. If you chose this option it adopts all passwords, wpa/2 configurations for security and such.
    I chose this option thinking that since it is an apple product it would take over everything and work. My airport express had origianlly been set to join my old Linksys network. Since the airport extreme took over this configuration it should work.
    Apple stated many times that there seemed to be a conflict and kept asking me about the placement of my airport extreme.
    My Linksys was never part of a bridge or a network within a network. It was removed before the Extreme was ever turned on.
    After all the problems and hours of trying with Apple, i find it funny that all I had to do to restore eveything was plug my old Linksys back in and conect all the cables, and bam....it worked.
    So what is wrong with the airport extreme, or is there something wrong with itunes 8 and its interface with the express? For whatever reason the extreme cannot make the express and my ATV work at the same time.

  • Wireless modem and Airport Express.. one at a time

    Recently my internet provider upgraded my old plug in modem to a newer wireless model. Now it seems that the current setting allow communication with only one or the other at the same time. If I want to be online with the wireless modem and send my iTunes music via Airport Express to my sound system, no dice. I have to either click on the modem up in the Airport choices to be online and listen to iTunes through the computer speakers, or go offline to listen to music through the sound system and Airport Express.
    I'm sure I'm just missing something in preferences or settings somewhere.
    Can someone point me in the right direction?
    Thanks, and Happy New Year!

    No ideas?

  • How to Set Up Time Capsule With Airport Extreme and Airport Express

    Just got a new 1TB Time Capsule. I want it to be the main base station for my network. I already have a network set up with an older Airport Extreme base station and an Airport Express to extend it. I am thinking that rather than setting up the Time Capsule to "join" the old network, the best approach is to disconnect the Airport Extreme and Airport Express and reset them. Then set up the Time Capsule as a brand new network and bring the reset Aiport Extreme and Express onto the new network as if my original network never existed.
    Is that the right approach or am I complicating it? Can I just join the Time Capsule to the existing network and still make it the main base station for the network?

    evelK wrote:
    Just got a new 1TB Time Capsule. I want it to be the main base station for my network. I already have a network set up with an older Airport Extreme base station and an Airport Express to extend it. I am thinking that rather than setting up the Time Capsule to "join" the old network, the best approach is to disconnect the Airport Extreme and Airport Express and reset them. Then set up the Time Capsule as a brand new network and bring the reset Aiport Extreme and Express onto the new network as if my original network never existed.
    Is that the right approach or am I complicating it? Can I just join the Time Capsule to the existing network and still make it the main base station for the network?
    I'd first use AirPort Utility to "Save a Copy As" of your AirPort Extreme settings. Then disconnect it, connect the Time Capsule in its place, and use AirPort Utility's "Import" function to read those settings. (Both of those functions are under AirPort Utility's "File" menu.) You may have to adjust a few settings. Once you have the Time Capsule working as you want, you can reconfigure your AirPort Extreme unit as you wish.

  • Can I stream music to apple tv and airport express at the same time?

    Does anyone know if I can stream music to both AppleTV and Airport Express (speakers) at the same time?
    I have a TV in my living room and external speakers on my deck and want to stream music to both at the same time so I have the same music playing in both rooms - but I can't get an answer on IF I can do both at the same time or it I'd have to select one over the other?
    Anyone know?

    yes - the built-in music app allows to select one speaker only at the same time.
    now i've found the WHAALE Multiroom Player App (http://www.whaale.com) - and it sends directly from the iOS Device to my 6 AirPlay speakers. One of them is an Apple TV...
    all "in sync" and without any special hardware and additional software.
    And i am able to stream different songs to different rooms...
    Just AirPlay speakers - wifi router - WHAALE -> that's easy :-)

  • I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

  • Connecting wireless modem and airport express

    I currently run internet with an old Motoirola Sideboard cable modem and Airport Express - previous version. All runs well. Now my Optus provider has upgraded my service with a Premium account for higher speed. They have also given me a free wi fi Cisco modem - DPQ3925. How can I replace my old Motorola modem and still maintain Air play etc with my new modem using Airport Express. I need to know exactly wire per wire help - please, if possible - Thanks
    Mac

    Hi - I have a similar issue.
    I have a new macbook pro, ATV (3rd Gen) and AXn (purely for Airplay of itunes).
    All three are wirelessly connected to my HG556a Huawei WiFi Router.
    The Macbook pro and ATV work fine and can see each other for airplay mirroring and itunes.
    The AX connects and comes up in Airport Utility (AU) and itunes shortly after you turn it on, but if you either dont use it or stop using it and switch to ATV or whatever it dissapears from itunes and AU says it cant find it. Randomly the light on the AX stays green the whole time.
    I have to switch the AX off and on to get it back working again (i.e. itunes and AU can see it).
    Following other forum posts I've set the AX up by hard connecting it to my router, setting a static iP and reserving ports 5353 and 3689 to that address. I've also turned off ipv6 or whatever using the networksettings Terminal code string. I have also repaired permissions with disk utility!
    It still dissapears from available options in iTunes and AU. ideas?

  • Network set up using airport extreme, time capsule and airport express

    I have searched for relevant answers but can only find different bits here and there.
    My set up is as follows:
    I have a Linksys wireless router running a stable wireless network for the other computer users in the house and wish to create an extended, additional network using airport extreme connected to the Linksys by ethernet to create the network and then time capsule close to my Mac Mini on my desktop and airport express at the other end of the house to try and extend the range of the network.
    I have been trying for 4 days to set this up but without success. I have tried all of the options mentioned in different posts, using WDS, extending a new network etc. I can get connection between the three devices but monitoring on iStumbler there appears to be little improvement in the strength of the signal, iStumbler also shows the time capsule dropping it's signal totally every 10 or so seconds for a few seconds and then I get a positive signal strength for another ten seconds or so.
    Can anyone help, it is driving me insane. I am a recent convert to apple computing and have been hugely impressed with all products until now. The claim that the set up of these wireless products is simple seems to be very exaggerated.
    I am happy to provide any relevant system or hardware information.
    Thanks in anticipation.

    I have an AirPort Extreme acting as a wireless base station, connected to a BT router by ethernet.
    Then the correct setting for Connection Sharing on the AirPort Extreme would be "Off (Bridge Mode)".
    If I set Connection Sharing to "Share a public IP address", I'm told that:  "The DCHP range you have entered conflicts with the WAN IP address of your Apple Wi-Fi base station"
    Exactly. You have two routers....The BT device and the AirPort Extreme in series with both of them trying to act as the "main" router when you configure the AirPort this way. That won't work.
    Only one can be the main router, and it must be the BT device in your setup. So, the AirPort Extreme....and any other AirPorts on your network must be setup to work in Bridge Mode to allow the network to operate correctly.

  • Apple TV Inference with Time Capsule and Airport express?

    I have recently bought an Apple TV 2, which seem to be working fine, however since installing it on my wireless network both my Time Capsule and Airport Express can't be found. Following some fault finding it seems that when I unplug the Apple TV I can reconfingure the TC and AE.
    The TC and AE are configured to join my existing network....and have happy sat there for a few years.
    I would really welcome any ideas.
    Thanks
    R

    Welcome to the discussions!
    It sounds like you have the basic configuration covered correctly.
    You might want to check some settings on the TC:
    Wireless Mode would be create a wireless network
    "Allow this network to be extended" should be checked
    The AX should be set to "extend a wireless network"
    The "allow wireless clients" box should be checked
    In this configuration, the ethernet port on the AX is active so things should work.
    A minor point...Although the TC is a dual band device, the AirPort Express is not. Can you make sure that that the Express is connecting to the "main" network on your TC? The "guest" network cannot be "extended".
    If you place your laptop close to the Express and hold down the option key while you click on the AirPort icon, some connection information will be displayed. The MAC address of the device that the laptop is connecting to will be indicated. Make sure that that this is the MAC address of the AX, and not the TC.
    Another note...If you have not changed the default "main" network, the radio mode is broadcasting 802.11n only at 5 GHz. These higher frequencies are absorbed by walls, ceilings and any obstructions much more quickly than 2.4 GHz signals. So, if you AX is some distance away, you may not be receiving a strong signal for the device at that location.
    If you have a signal strength utility on your laptop (the "bars" at the top of the screen are not a very good indicator of actual signal strength), turn off the AX and take a reading to see what kind of signal the Express is receiving where it is located.
    Please post back with your results.

  • Bt Infinity, HH3 and Airport Express

    am thinnking about taking BT infinity. THis apparently needs HH3. Have seen threads about connection problems between HH3 and airport express. (I had similar problems with HH2, so resorted to old BT Voyager)
    1. does anyone know if problems with HH3 and airport express can be fixed
    2. Can I use BT infinity with a BT Voyager
    thanks

    Re: "If you get Infinity you will not need the HH3 in the first place you can just connect the Airport Express to the Openreach modem."
    No use at all. I don't know what you use your Airport Express for, but mine is used to send music to our hi-fi, and so has to be connected to the hi-fi. Therefore it cannot also be connected to the modem.
    This worked fine when I used to get my internet via (whisper quietly) Virgin. But with BT Infinity it would lose its connection every now and then. Apple provided a free replacement but that was no better. Following a few tips (e.g. connect to one's laptop via ethernet cable for setup) I was able to set up a connection eventually, but it still loses connection quite frequently. Interestingly enough, resetting the hub gets it going again, though restarting AE does not!

  • How to setup ADSL moden router and Airport Express 802.11n (1st Generation) to provide internet and airplay connections to multiple devices?

    I have a Netgear wireless ADSL modem router (wireless + four ethernet out ports)  that i'd like to connect to a 1st gen Airport Express to create a small home network to provide internet access for a MacBook, iPhone and Apple TV, and to provide Airplay connection to the Apple TV and Airport Express audio output jack.
    I'd like to turn off the wireless function of the ADSL modem router, and to have from one of its ethernet out ports an ethernet cable providing internet directly connected to my MacBooks ethernet port.
    Then from one of the other ethernet outs on the ADSL modem router an ethernet cable connected to the Airport Express's ethernet port. This would be to provide wireless internet connection for the Apple TV and iPhone via WiFi from the AE.
    At the same time as the MacBook is receviing internet soley via the ethernet in port, i'd like it to have WiFi connection to the AE to provide Airplay connection to the Apple TV and the AE's audio out jack.
    Is this all possible? How should I go about to configure this? How should the AE's ethernet port be configured?
    Any special modes the ADSL modem router or Airport Express should be in? ie bridge or client?
    Thanks

    On the ADSL modem router web-based interface, should I set any security setting? I think not as there'll be no wireless signal coming from it, only wired ethernet connections to both MacBook and AE. Security should only be set on the AE to prevent someone from accessing its WiFi signal. Is this assumption correct?
    These are all correct!
    How should I go about setting up security for this network?
    First I would recommend that you configure the AirPort Express for WPA2 Personal. This will provide you with the greastest level of security while still providing excellent bandwidth performance.
    You would configure wireless security for the Express by using the AirPort Utility on a Mac, PC, or iOS device. Using your MacBook Pro as an example, you would do so as follows:
    Run the AirPort Utility.
    Select the Express, and then, click on Edit.
    Select the Wireless tab to enable it.
    Set the Wireless Security option to: WPA2 Personal
    Enter the desired password in both the Wireless Password & Verify Password fields. Note: Use of a "strong" password is encourage here. By strong, I mean use a mix of upper/lowercase letters, numbers, & punctuation marks. Try not to use common dictionary words. If you operate your wireless in an area where security is of an utmost concern, I would further suggest that you change the wireless security password every 60-90 days. Also don't forget to change the default AirPort Base Station Administrator password as well.
    Click on Update and allow the Express to restart.

  • Apple TV doesn't show up in iTunes when AirPort Express is running at the same time - Can't play music on both Apple TV and AirPort Express speakers together

    Hi there!
    I am trying to play music from my Mac on multiple speakers, Apple TV and AirPort Express. But as soon as the AirPort Express station is plugged in, the Apple TV does not show up in iTunes anymore. When trying the same using iPhones Remote app it works perfectly.
    Does anyone of you have an idea why iTunes does not show me both Apple TV AND AirPort Express? (it has nothing to to with the IP adress as the adresses are different).
    Thanks for any help!

    As my english isn't too good I made a screenshot to show you what I mean.
    As you can see in the image below iTunes only shows me the computer speakers and the AirPort Express. But at the bottom you can see that iTunes actually recognized 3 different speaker (Mac, AirPort, Apple TV 2). Why does the Apple TV not show up in the multiple speakers window? Any ideas?

  • I just purchased Apple TV AND AIRPORT EXPRESS. I am questioning if  I need it when I already have a Netgear Powerline AV 200 Adapter Kit XAVB2001. Does the Airport Express do the same thing?

    I just purchased Apple TV AND AIRPORT EXPRESS. I am questioning if  I need it when I already have a Netgear Powerline AV 200 Adapter Kit XAVB2001. Does the Airport Express do the same thing?

    Thank you so much.  Any specifics I should know about prior to connecting? The goal is to watch  Netflix from my iPad or iPhone 5 on my tv (located in different room from where Comcast internet modem is hard wired to main computer in house).  Movies would depend on wireless transmission to a smart tv not connected to modem.

  • Is there a limit to the number of airport extremes and airport expresses one should have in a network?

    Is there a practical limit to the number of airport extreme base stations and airport express units one should have in a home network?

    Then, I had an older Airport extreme that I was thinking about connecting wirelessly in my living room and connecting the DirectV DVR to it by ethernet cable.
    Is this older AirPort Extreme the "round" version or the "square" shaped version? The "round" version will not do what you want.
    Whenever you extend an AirPort using wireless only, you will experience a loss of bandwidth (speed) on the entire network. That loss might be anywhere from 15-50% depending on how far the extending AirPort device is located from the "main" AirPort.
    Even with an excellent signal, if you have 3 AirPorts extending the signal, you will lose 40-50% of the bandwidth on the network. The other AirPorts that are being used just for music are also slowing things down.
    He thought there might be problems with using that third airport with the DVR and wondered if I should just use an Airport express there.
    It would make no difference whether you used an AirPort Extreme....assuming it was the "square" version or a new AirPort Express as far as performance is concerned.
    As to whether you connect the DVR to another AirPort, it might be OK, but you will not know until you try. 
    If you find that things slow down noticeably, you will need to look for ways to connect the AirPorts together using a wired Ethernet connection. This is always the preferred connection method since there is no bandwidth loss when you do this.
    Since downloading video places a high demand on a wireless network, you might want to look for a way to connect the DVR back to your "main" router directly using a wired Ethernet connection as well.

  • Can you share iTunes music w/Apple TV and Airport Express?

    Can you share iTunes music between Apple TV and Airport Express?
    I have been very happily using 2 Airport expresses to share my itunes library from my iMac to 2 other rooms. I just bought an Apple TV for the bedroom (and I ASSUMED to replace the Airport Express), and can not figure out any possible way to have the same music in 3 rooms any more.
    Anybody have any ideas?

    I think you may have misunderstood the OP, I believe they wish to be able to walk from room to room and listen to the same music over the tv and the express. itunes will send music to the tv and the express at the same time but in two different streams, so even if you chose the same music over each device it would be quite difficult to sync.

Maybe you are looking for

  • My iMac has the Mac OS x 10.5.8.

    Will I be able to update it to 10.6.8 which seems to be required to get snow leopard and following upgrades? i have 4GB ram and the required processor.

  • Data Warehouse report query using Entity Beans

    I have used the EJB technology on one project, so I am not all that familiar with best practices. In my new project, I have to produce reports using a query that goes against a dimensional database. I am wondering what options I have to run the query

  • Short dump in delta extract  using bgRFC in NW 2004s

    Short dump in delta extract after Support Pack install, using bgRFC.  InfoSet Query extractor from Z-table residing on BW system into ODS.  Init and Full loads load successfully, delta loads short dump. "MESSAGE_TYPE_X"         "SAPLARFC" or "LARFCU2

  • Choose a Text Object that...

    Hi, I want to have a multiline text field (3 lines) that puts automaticly text in a new line if the text is longer the the line's lengh. I used JTextField and JTextArea, couldn't set it to fulfill my needs. Maybe something different? Or maybe I could

  • A website offers me to save a file as .xls, but when I try to save, it gets saved as .do file type?

    The service website offers 3 options: Save as csv Save as xls Save as xml All 3 options when tried to save, saved as a .do file. Why is it so?