Unknown Skill Group in IPPA Stats

Hi,
I have recently install CAD 8.5(2a) in two lab environments both experienced the same issue. Basically, when I login an agent to IPPA, the Skill Status dislplays two queues. One of it is what I configured, but the other one is showing as 12 digit string, which I don't recognize at all. Checked skill group explorer no such item in there, but in CUIC it pickes up a funny group as well, named as "PIM1.Cisco_V.40178".
Any idea why this unknown SG is created on the system?
Thanks

That is a default skill, used for outbound calls. Some related threads:
https://supportforums.cisco.com/message/3164470#3164470
https://supportforums.cisco.com/message/1033029#1033029
https://supportforums.cisco.com/message/3298523#3298523
HTH,
Chris

Similar Messages

Queue to skill group node with consider if statement.

Hello,
I have a question on a queue to skill we have set up. There have been complaints that calls have not been able to be answered after the center closes even though they are logging in an agent or two to clean up these calls. Within the queue to skill is consider if statement that says:
IF call center location is open and there is at least one agent logged in, queue the call to this skill group.
This applies to both skills that are in this queue to skill node. What they are saying is that if there are calls queing after the center is closed and they have already passed the consider if statements and are sitting in MOH/queuing, would these consider if statements not allow the call to be delivered to an agent if they log in after the center is closed as they are stating that they will log an agent in and they still can't pick up the call. However, these are agents at 2 different locations on 2 separate PGs so that throws another variable into the mix. Not sure how much of the truth they are telling either....
Also, is there a way to check if the call is queing to both groups or just one? Not sure if there is something in the DB that will tell you this, I know there is a route field in RCD but I'm assuming this will only popluate after a call is handled.
There is also a TOD check that will not allow calls to this queue if it past hours of op built in as well.
Thanks

Paul,
It sounds like the first "IF" statement is being used as an "accept or deny" calls access to the queue node-
If the queue to skill group node is the where this decision is made(perfectly acceptable to do so)- once a call passes through the queue to node- calls do not return to it unless you loop though it.
Think linear-
Start----Queue to(with if) -----play music-----play announcement--------wait-------loops back to play music-------
Queue to node (conditions-if agents logged on queue the call, if not, the call is not queued)-If calls do not get queued in this step, calls are just in the treatment, not actually queueud- even if your subsequent steps are to play music, play prompts etc- the call is not queueud.
I do not recommend this---but it would resolve the issue if agents logged on after the call was in the treatment----
Start----Queue to(with if) -----play music-----play announcement--------wait-------loops back to queue to(with if)------
Logging in agents to the queue would not automatically add callers to the queue-
the script would need a new queue to node during the treatment- again looking to see if agents signed on.
I would advise adding an Admin Script with TOD/ DOW conditions and then set a variable for open/ closed-
If the script is "open" queue the calls to the skill group, then if agents do sign on to the queue the calls can be answered.
Start---
IF Node(if open)---->Queue to(if not required here) -----play music---play announcement---wait---loops back to play music-
'------>(if closed) play after hours greeting/ route to voicmail/hangup.

Skill Group Name is not coming on Cisco CTI Tool Kit real time status

Hi,
I have UCCE 9.0.3 in my environment but when supervisor is monitoring agent state on CTI Toolkit Team Real Time Status we are not able to see Skill Group name.
For your reference I have enclosed screen shot of that.

Hi,
first, read this document: Recommended Tracing Levels for Troubleshooting IPCC Issues. Apply the recommended trace levels to the following services:
CTI OS Server
CTI Server
But first take note of the original values (so you can switch back to normal tracing).
Dump the logs for both the above services: How to Use the Dumplog Utility.
For instance: dumplog ctisvr /hr 1 /of c:\temp\ctisvr.log
Post the logs to here.
G.

Will Enterprise Skill group allow queuing with interrupt ?

Dear All,
I have a requirement to use three enterprise skill group in a single ICM script.
Customer dials TFN and if agents are in ready state they will take a call.
If no agents were available in both enterprise skill group the call goes to queue(hold music), once agent become available customer call will patched to the agent.
In our case, we have three enterprise skill group with overflow concept assume no agents are available and the call sucessfully goes to queue, and once the agent become available, call was not landing to agent instead of this call gets disconnected after queue prompt was played.
Note: Interruptible was working if we use Queue to skill group and the same was not working if we use enterprise skill group
This was my script
Kindly do let me know the solution for this
Thanks
Srinivasan

David,
Thanks for reply, yes every thing was working as expected. Only interrupting was not working and also queue music was playing only one time.After queue music played the call get disconnected
If i use queue to skill group with the same scenario it was working, pls tell me why the same was not working if i use enterprise skill group..kindly find the below screen shot which is working if i use queue to skill group
Srini...

UCCE 7.5 Skill group expansion

I have an issue where
I want to queue to a skill group for say 5 mins and then expand it to another skill group or groups. What is the best way to do this?
My thoughts:
1) add skill group to initial queue to node with a consider if statement
2) add an if statement after the initial queue to node?
Other options or opinions?

1. Will not work assuming this if the first queue to SG node it sees. So you just queue the call.
2. This will work assuming you have the check in the right place. For example, to check after 30 seconds of music on hold.
david

Queue to Skill Group node Failure

Queue to Skill Group node failing on load and sometimes witout load
Router Log Viewer
3/28/2013 1:04:07 PM          Call route request from routing client CVP_PG_1G (ID 5015) with unknown DN of 7771111000.
3/28/2013 1:04:08 PM          Call route request from routing client CVP_PG_1G (ID 5015) with unknown DN of 7771111000.
3/28/2013 1:04:12 PM          Call route request from routing client CVP_PG_1G (ID 5015) with unknown DN of 7771111000.
3/28/2013 1:04:12 PM          Call route request from routing client CVP_PG_1G (ID 5015) with unknown DN of 7771111000.
3/28/2013 1:04:14 PM          Call route request from routing client CVP_PG_1G (ID 5015) with unknown DN of 7771111000.
rtrtest logs
:40:29:245 ra-rtr Trace: (29437 29438 12329 : 0 0) CallEventReport: CID=(150565,47621458),Event=DISCONNECT, DlgEnds=1, FromVRU=0, CallState=2, Cause=NORMAL
16:40:29:245 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog received event report 6 from NIC during RunScript.
16:40:29:245 ra-rtr Trace: (29437 29438 12329 : 0 0) Canceling queuing for CID=(150565,47621458)
16:40:29:245 ra-rtr Trace: (29437 29438 12329 : 0 0) Unqueuing Call CID=(150565,47621458) for SkillGroup CUCM_PG_1.Cisco_Voice.SMDSkill, pos=14
16:40:29:246 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog sending VRUQueueEvent to VRU (4)
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog handling script resp
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) CallEventReport: CID=(150565,47621458),Event=DISCONNECT, DlgEnds=1, FromVRU=0, CallState=22, Cause=INVALID_CAUSE
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog (callstate:22) received event(6)(Call disconnected. (Event has dialog end set.))
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog resuming (Call disconnected. (Event has dialog end set.)) status (3)
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog aborted and was deleted.
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) Dialog sending release call to VRU
16:40:29:252 ra-rtr Trace: (29437 29438 12329 : 0 0) Deleting Dialog.
16:40:29:252 ra-rtr Trace: For message (9) from routing client CVP_PG_1F (ID 5014) could not find dialog id (29438).
16:40:29:254 ra-rtr Trace: Received dialog fail for unknown dialog(29438) from PG.
CVp VRU PIM logs
Line 15925: 16:46:11:090 PG1A-pim7 Trace: DIALOGUE::NoSuchRouterDIDError:DIALOG_FAIL RCID=5014 PID=5000 FailureType=2 NumOfEvents=1 DID=29677 DIDRelSeqNo=-1 ReasonCode=1
Line 15946: 16:46:19:533 PG1A-pim7 Trace: DIALOGUE::NoSuchRouterDIDError:DIALOG_FAIL RCID=5014 PID=5000 FailureType=2 NumOfEvents=1 DID=29695 DIDRelSeqNo=-1 ReasonCode=1
Line 15958: 16:46:20:690 PG1A-pim7 Trace: DIALOGUE::NoSuchRouterDIDError:DIALOG_FAIL RCID=5014 PID=5000 FailureType=2 NumOfEvents=1 DID=29584 DIDRelSeqNo=-1 ReasonCode=1
Line 15960: 16:46:20:691 PG1A-pim7 Trace: DIALOGUE::NoSuchRouterDIDError:DIALOG_FAIL RCID=5014 PID=5000 FailureType=2 NumOfEvents=1 DID=29584 DIDRelSeqNo=-1 ReasonCode=1
Trying on Simple Script now:
Ideas and response appreciated. Thanks.

What ivr type is being used. It seems the call correlation is failing when the number ends 0 check either your translation routes or that you correlation I'd does not start as 0 as this will cause calls to fail
Sent from Cisco Technical Support iPad App

Cisco ICM CMS intergartion to check skill group status

Hi,
We are trying integrate Cisco ICM (8.5.6)with Avaya CMS.
The goal is to check agents stats in skill group configured in Avaya and queue call to VDN.
I am following Avaya-ICM integration guide and trying to build best formula for this.
Please let me know if anyone has done this before.
Thank You!

I could see and monitor the Avaya agents from PG PIM and were able route calls also.
I am using following formula to calculate EWT,
ValidValue(((SkillGroup.SY1_CMC_Tech_01.RouterCallsQNow+1)*(ValidValue(SkillGroup.SY1_CMC_Tech_01.AvgHandledCallsTimeTo5,50))/max(SkillGroup.SY1_CMC_Tech_01.Ready,(SkillGroup.SY1_CMC_Tech_01.TalkingIn+SkillGroup.SY1_CMC_Tech_01.TalkingOut+SkillGroup.SY1_CMC_Tech_01.TalkingOther))),100)
I used set variable to write the value in DB.With 4 agents logged in and talking and 4 calls in queue,I am getting 16.XX as EWT time.
The business requirement is 180 seconds of EWT and if not then route the calls to different destination.This formula is working but LAB has some limitation of number we can log in.
Any help in approach to test this formula will be appreciated.Thanks!

UCCE - Default Skill Group Clarification

Looking for clarification on which stats track against an agent's default skill group - ucce 9.1. Specifically, in which circumstances would calls offered/answered be incremented against the default skill group?
The scenario is an agent with 2 lines - 1 DID and one not. The agent states that he logs in using the non-DID line and that no calls were placed/received on the DID line. Grain of salt. Occasionally, there will be a single offered and answered call on a skillgroup report against the default skill group -- and not just for this one agent -- it's happened with a couple of agents. It's my understanding that if an agent manually places an outbound call, it'll be tracked against the default sg, but when would an inbound call hit that sg?
I've made some tests (transferred call to either line, inbound call to the DID line, etc) but haven't been able to make any test call hit the default sg. Any ideas?
thanks,
will

Will,
Offered/Handled should only occur for calls delivered by call center. The a few ways I can think of to deliver a call center call to a default skill group (without selecting the skill group):
Queue to Agent node
Select node followed by Agent node
Agent to Agent node
Label node, routed to extension that the Agent is logged into
That said, I think 1-3 are likely the only options that will increment Offered/Handled.
-Jameson

UCCE 7.5.10 - Modify Agent Skill Groups via Database instead of Config or Re-Skill tool?

Background - We would like to bulk modify agent skill groups on a weekly basis, but have over 400 agents, 3 teams and over 5 skill groups per agent. We are hoping to build a query to modify the tables required to skill an agent properly. We would problably use a .csv file from our fiance dept. to determine skill groups per agent.
Has anyone been successful or know what tables must be updated/inserted to change an agent's skill groups? Is there a hack/workaround to do it using POST/URL in the Cisco Reskill Tool?
Thanks,
Ray Khan

It is about time for Cisco to realize that this is something that their biggest contact center competitor, Avaya offers as a standard feature, out of the box (I'm sure they know it without me pointing it out). This is "old" technology for Avaya.
We are doing this now in our Avaya contact center with a VB Script and scheduled tasks in Windows. Needless to say, it didn't take a developer to set it up. The scheduled tasks run twice per day to "reset" the agents' skills to pre-determined default values. This allows us the spend less time worrying about intraday skill changes, and whether or not any additional skills were removed from an agent's profile. We know that they'll be changed back twice per day.
We essentially have three different configurations based on time of day and day of week: Monday through Friday, 6:00am to 6:00 pm (Business Hours); Saturday and Sunday 6:00am to 6:00pm (Weekend Daytime); and Sunday through Saturday, 6:00pm to 6:00am (Overnights). We would have to have three UCCX skills with time of day routing to every one Avaya skill achieve this in UCCX.
Also, this capability enables us to re-skill our entire call center, or any subset thereof to a predetermined skill-set with a single mouse click.
I'd love to see Cisco allow and support this or similar functionality.
Sent from Cisco Technical Support iPhone App

RoutercallsQnow not displaying in Skill group statics in ctios desktop 9.0

RoutercallsQnow not displaying in Skill group statics in ctios client Desktop.
I reviewed this bug
CSCma08461 but was repaired in version 5.0 and the problem as I have in version 9.0
any recommendations?
Thanks
Ivan

Hi,
what does it mean "not displaying"? What do you see? Zero? NULL? An error message?
Was the CTI OS server restarted recently?
G.

Is there a way to add multiple agents to a skill group at once?

Hi All,
Is there a way to add multiple agents to a skill group at once by using bulk edit or some other means?
I am using ICM 8.0
Thanks in advance.

Hi Piyush,
There is a tricky way of doing it in the config manager. Say for example, if you have 100 agents to be added, rename the agent so that they get listed first while adding to the skill group. This will reduce the effort of searching the agents. You can scroll and select the total number of agents till it is renamed and revert back once added to the skill groups
Hope this helps
Cheers,
Dass
Please rate useful posts

UCCE 7.2 Missing Skill Groups in Supervisor Work Flow Setup

Hi, one of our customers reported that when they try to configure a Work Flow for their supervisors in Supervisor Desktop, there are Skill Groups missing from the Available Skill Group List.
I've tried to figure out what might cause this, and the only thing I've found that is different between the visible Skill Groups and the missing ones is that in Desktop Administrator => Personnel Configuration => Teams I can see that the missing Skill Groups don't have any Skills listed in Selected Skills under the Skills tab.
I've tried to find out where in ICM I can add the Skills, as the documentation says it's configured there, but I haven't had any luck so far.
Anyone have any helpful tips please?

Hi
From the problem description I understand that you are seeing "available Skill groups" empty while trying to add a new work flow through CSD.
This is a known defect with 5.x version which has not been fixed yet
http://tools.cisco.com/Support/BugToolKit/search/getBugDetails.do?method=fetchBugDetails&bugId=CSCth04959
In 7.x this issue is not seen
Hope this helps
Regards
Anuj

Query Skill Group - Translation Route mapping from Routing Script

Hi,
Is there a way we can query against the individual routing scripts and extract the PSG-TR mapping?
In ICM we can map any particular Peripheral Skill Group (PSG) to a specific Translation Route (TR) defined on the same Peripheral Gateway through ICM routing scripts.
The PSG and TR are both configured through ICM configuration manager and the details are stored in the ICM DB which can be queried against.
However the mapping between the PSG and TR is done through a routing script using Script Editor.
We would like to make an SQL query where we can see PSGs associated to a Translation route on Routing Scripts.
Product: Unified Contact Center Enterprise (UCCE)
Version: 8.5(4)

Hi Gergely - how would you then query this data if you required it? Is there a way to map the PSGs to the Translation routes they are associated to?
Thanks!

UCCX 7 Supervisor Workflow Skill Groups Missing

I am trying to make a new work flow rule in CSD, under the "Tools -> Supervisor Work Flow Administrator" option. I already have multiple rules that are running with no issues. However for the new rule that I am trying to create, I've noticed that the skills I want to add as the Skill Groups, are not showing as available. These skills (and a lot of others) are not under any other rule that is currently in place, so they aren't missing because they are in another rule. They just plain aren't there. Has anybody run into this issue and if so, were you able to resolve it and how? Thanks.

If you look at the team configuration in appadmin, is this supervisor in a team that has CSQ assigned to that team? Also check the version of CSD, make sure it matches the server version in the compatibility information.

Export Skill Group Members list for UCCE 8.5

Hello,
We are working with UCCE 8.5 and will be making some major bulk skill group changes. We are looking to do the following:
-Export a list of the members of specific skill groups so that we can revert to original skilling if necessary.
-Bulk editing the members of specific skill groups. The current method of adding/removing skills via Agent Explorer or Skill Group Explorer will not be scalable in the future.
I've tried a variety of SQL queries and manipulation of the Bulk Insert/Edit tools, but have not come up with a solution yet and am hitting my head against the desk at this point. Any direction or advice is appreciated. Thanks!

Hi,
exporting is easy with SQL. The simplest query may be:
USE [icmInstance]_awdb
GO
SELECT
ag.*, sg.*
FROM Skill_Group_Member sgm
LEFT OUTER JOIN Agent ag ON sgm.AgentSkillTargetID = ag.SkillTargetID
LEFT OUTER JOIN Skill_Group sg ON sgm.SkillGroupSkillTargetID = sg.SkillTargetID
The Database Schema docs contain all the necessary info:
http://www.cisco.com/en/US/products/sw/custcosw/ps1844/prod_technical_reference_list.html
Bulk editing: this is what the various "Bulk edit" options are within ICM Configuration Manager. Yes, that's it.
Before you start experimenting with writing into the configuration tables: that's an excellent way of losing Cisco's support. And no, there's no public configuration API available.
G.

Unknown Skill Group in IPPA Stats

Similar Messages

Maybe you are looking for