Unnecessary rebooting at the end of burning process
When I burn a CDR by itune, my PC goes rebooting unnecessarily at the very end of the burning proicess. I think that when itune gives an eject signal in the end, PC gets it as a reboot or a reset signal. CDR by the way is always burned propperly, but rebooting without normal saving process at every burning may not be healthy for the hard disk. Is it a problem in itune, or driver of the CD-burner? Or mother board?
PC given with mobile phone contract Windows XP
Free PC given with mobile phone contract Windows XP
hi ryochi!
my PC goes rebooting unnecessarily at the very end of the burning proicess.
are you getting any sort of blue screen? if so, what numerical and text codes are you getting with it? (ie 0x[zeros/letters/numbers] CAPSANDUNDERSCORES)
here's a reference on the sorts of things i'm asking about:
Troubleshooting Windows Stop Messages
if you're not seeing a blue screen (or just a flash of one), we can use this technique to make hidden blue screens appear for us:
1) Open your system control panel (Start->Control Panels->System).
2) Select the "Advanced" tab.
3) Click the "Startup and Recover" section's "Settings" button
4) Verify that under "System Failure" the "Automatically restart" checkbox is not checked.
love, b
Similar Messages
-
'Error at the end of form processing' - Adobeforms
Hi All,
I am facing an issue while opening travel request form in PDF with an error showing as 'Error at the end of form processing'.
I checked all configurations from R/3 and everything seems to be fine.
Appreciate for your valuable inputs for solving the issue.
Thanks & Regards,
Srujana.Hi,
You provide some more details for the problem. It seems FP_JOB_CLOSE is returning some error. Check that once.
Thanks,
Nitin -
IDVD doesn't respond after it says "Done" at the end of Burning
Firstly, I have burn many, many, MANY DVD's before in iDVD (for school camps, special occasions, etc.) and have met this problem before, but in a different way. Those times I was burning about 20 copies, and after about 7 or 8, it would say this problem. My solution was to press cancel, then start burning again IMMEDIATELY, and it would work again.
The Problem: that when burning a DVD (it's a project on Apple as a company. Kinda ironic, because it's all about how fantastic they are, and then this happens). What happens, is that iDVD processes the movies, menus, slideshows, etc. and then gets to the "Burn" part of the burning. Here, the process bar is slowly moving forward, and after about 5 minutes of burning (very normal for my mac) it ejects; BUT!: the menu left on iDVD stays on the "Done" screen forever (at the end of the burning, the remaining time is Done). I checked on my other computer and again on my mac, and it is positively blank (the drive also didn't make as much noise as it usually does when burning). This may have something to do with that it is the first time I have exported a Keynote to a QuickTime, and then put it into iDVD (and I also put some "Get a Mac" ads off the Apple website on it). I asked a good friend of mine about this, and suggested that I put the ads into iMovie '09 and then export into iDVD, just so that they are all definitely the same format, but it didn't work AGAIN! So I put the ads into Keynote, deleted them from iDVD, re-exported them and failed to burn AGAIN X 2! HHEELLPP!!!!!!!!!!!!!!!!!Update: The problem still occurs, but I had the project due in today, so I put the quicktime of the Keynote on a flash-drive and ran it off my School computer (not a mac... unfortunatley).
-
IPod reboots at the end of a song....Help!!!
after doing the firmware update at the weekend (and updating to itunes 7) my ipod now intermittently reboots itself at the end of a song.
it doesnt happen during every listening session, and not always with the same song - it just happens intermittently.
when it reboots it goes to the black screen with the white apple logo.
has anyone else had this problem?? it was ok prior to upgrading.
thanks in advance!some podcasts make it reboot also.
-
Itune error code 3 come at the end of restoring process
help!! my iphone 5 is stuck in recovery mode and when I try to restore it,my iphone start restoring (ios7.1)but in middle of restoring I get itune error code 3,so pls help and the error come at the end of restoring process
aparsethi wrote:
but in middle of restoring I get itune error code 3,
Check for hardware issues
Related errors: 1, 3, 10, 11, 12, 13, 14, 16, 20, 21, 23, 26, 27, 28, 29, 34, 35, 36, 37, 40, 1000, 1002, 1004, 1011, 1012, 1014, 1667, or 1669.
Try to restore your iOS device two more times while connected with a cable, computer, and network you know are good.
Also, confirm your security software and settings are allowing communication between your device and update servers.
If you still see the error message when you update or restore, contact Apple support. -
[Solved] Disable screen clearing at the end of boot process?
During the boot process Arch shows some messages on the computer screen while the system services are started. Then it clears the screen just before showing the login prompt, which means that you have to be a really quick reader to be able to catch the final boot messages before they disappear.
I'd prefer that Arch wouldn't clear the screen at all, so that the final boot messages would stay visible even when the login prompt appears (and I could scroll the framebuffer to see all the boot messages if I wanted to). Any idea how I could tell Arch not to clear the screen before the login prompt?
Last edited by darkglow (2009-08-12 19:28:48)Pressing Shift and PageUp at the same time should scroll the framebuffer up, and Shift+PageDown scrolls it down. But if you've switched to another virtual terminal and then come back, the scrolling doesn't work any more.
I just tried scroll lock, it doesn't seem to make any difference? -
Encore Crashes near end of burn process
Hello,
I am trying to burn a DVD in Encore CS4 on my MAC. I created this DVD using Premiere and then used Adobe Dynamic Link to bring the Sequences to Encore. The DVD is 13 chapters and about 1 hour 12 minutes. After creating the DVD in Encore, I was able to burn one copy. I noticed some items that needed to be updated so I made the changes in Premiere and then attempted to open the .NCOR file to bring the changes in. Many times, Encore will hang up when opening the file - I able to get the file open and made some changes, and burned one copy... Another viewing lead to so final changes. I am now trying to burn 10 copies of this DVD. Again after making the changes in Premiere, many times Encore will hang up when opening the .NCOR file. The couple times I have gotten it open, it has transcoded for 12-14 hours and then crashed prior to burning anything.
This is incredibly frustrating!
I did try to create a new Encore project using the menu and importing the same sequences as in the first project, but Encore hung up when bringing in the first sequence via Adobe Dynamic Link.
Any help would be greatly appreciated.
Thanks!
TedI am now trying to burn 10 copies of this DVD. Again after making the changes in Premiere, many times Encore will hang up when opening the .NCOR file. The couple times I have gotten it open, it has transcoded for 12-14 hours and then crashed prior to burning anything.
This does not fix your transcoding/build problems, but build to a folder or image or folder, then use that as the source (rather than the project), to avoid needing to burn one more and having the whole build hassle again.
Many times, Encore will hang up when opening the file - I able to get the file open and made some changes, and burned one copy.
On windows, so other issues may be present. I was only briefly on CS4 (on WinXP), and more on CS5 (on Win7). I found that some projects just had a very long load time - they appeared to hang, but did not.
I had one sequence (only the one from a particular project) that would hang. I found I could work around that one if I opened it in Premiere before opening the Encore project.
it has transcoded for 12-14 hours and then crashed prior to burning anything.
If it is a transcode problem, this won't help, but I prefer doing a "transcode now" so that that step is separate from the build. -
Encore crashes at the end of encoding process
CPU quad core 9550,8 RAM DDR2 memory,1000 PSU,NVIDIA nforce 780i
Can somebody help me with this problem? I'm trying to build a blu-ray disc but when is finishing the encoding the encore crash and crash. and every time when crash, there is a blue screen with a different error mesage with a different Technical info: The last today was:
Tecnical information:
***STOP: 0x0000003B (0x00000000c000001D, 0xFFFFF80001E69638, 0xFFFFFA6005F2B2d0,0x0000000000000000)
Please helpTo go along with Jeff's comments, you might want to follow the links in this ARTICLE for some very useful tools.
I also agree that a BSOD is almost always hardware, and often heat (see Speedfan), or RAM (MemTest, and others), the Powersupply, or the MoBo, pretty much in that order.
Good luck,
Hunt -
Raise event at the end of process chain
Gurus,
I would like to raise an event at the end of my process chain run. I need this event to schedule a file extract using RSCRM_BAPI.
How do we raise an event at the end of process chain?
Regards,
-Sonny1) First create an event in SM62. Lets say ur event name is ZTEST and event param is also ZTEST.
2) Then In SE8 ---> Create a program say 'ZPROGRM' as follows.
DATA: EVENTID LIKE TBTCJOB-EVENTID.
DATA: EVENTPARM LIKE TBTCJOB-EVENTPARM.
EVENTID = 'ZTEST'.
EVENTPARM = 'ZTEST'.
CALL FUNCTION 'RSSM_EVENT_RAISE'
EXPORTING
I_EVENTID = EVENTID
I_EVENTPARM = EVENTPARM.
3) Include this 'ZPROGRM' at the end of ur PC
Regards,
R.Ravi -
Systemd service at the end of boot (login prompt)
hi guys..
i'm trying to start a script using systemd..
in my script the first thing i want to start is jack server on usb audio sound card..
the problem is that jack service is started before module is loaded so it gives error that sound card does nit exist..
is there a way to start the servuce at the end of boot process or after module is loaded..?
thanksI'm back..
I tried to use:
Requires=systemd-modules-load.service
After=sound.target systemd-modules-load.service
But it loads it before dbus and some other stuff and it does not work..i still have an error no device found..
Then i added
Type=idle
And now it starts..but if i want to add more services dependent of this one..it starts them before this one loads.. -
I'm trying to burn an iMovie in iDVD and at the end of the whole burn process it says "Multiplexer Error" "there was an error during formatting". How do I fix it so that it'll burn?
Hi
Multiplexing error is a very complex problem due to many things (long long list following) - one common but not obvious reason is that material on the iDVD menu goes outside the TV-Safe area (or just touching it).
So first - turn on TV-Safe area and move any object well inside of this.
Wide screen stretched - usually (as I think) it is due to making a 4x3 movie in a 16x9 wide-screen project OR the other way around. This forces one to on flat-screen TV (or other) set the presenting view right - My has 4x3, wide-screen, zoom and auto-wide-screen and I have to switch this by my remote for some DVD I've made "wrong" way.
Now my long long list on Multiplex Error
LONG LONG LONG LIST
Multiplexing Error
PART One.
Use of strange video/audio material e.g. .avi, .wmv, .mp3 etc.
I only use.
Video - StreamingDV (miniDV tape via FireWire) and
Audio - .aiff (as on audio-CDs) (else converted to this .aiff 48KHz)
Photo - .jpg (.bmp known problematic)
Chapters !
A. Using strange letters in video project name e.g. +,/; etc. keep to a-z and 0-9 strange letters in project name e.g. +
as described by Donnyboy69. Does the title of your project have any symbols or decimal points in it. If so, that is why you are getting the error. I had a project that had a + sign which caused the same problem. I renamed it without the symbol and low and behold, it worked.
B. Location of Chapters
• Can’t be at start or end of movie (Skip first/start one - iDVD sets this by it self. At the End - no need)
• Not in a transition (or within 2-3 seconds from it)
Important when from iMovie HD6 or previous - Now also observed when using FCE 4
PART Two.
from Robert Modero.
"Multiplexing Error. Problem during initialization of tracks"
Simply remember to add subtitles to your Quicktime files and menu buttons.
Once I did that, I was back in business.
from Boise Jim
Do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
I always makes a DiskImage first and test this so that it runs OK
I use only - Verbatim DVDs
I use only - DVD-R
I burn at an as slow speed possibly e.g. x1
This gives good DVDs
PART Three.
Multiplex Error
Chuck, Chicago 2/7/2009.
Back again. Here is what I have found to work. I also have and use a LaCie DVD-R/RW DL external drive and a LaCie external hard drive as well. Since yesterday I have tried a few ways to burn a themed iDVD project having four 56 minute movies on it, amounting to 226 minutes onto a DVD DL disc, capacity 240 minutes. Apple tech support really didn't know what to do but gave me a very good tip. I had two options left. Apple tech support's tip was to try disc image. One of the replies on a thread with this subject said not to, but my experience today is good. Put your project onto "Burn to disc image," under "iDVD, file." Yesterday encoding took me 23 1/2 hours. Overnight for iDVD disc image, encoding took 21 1/2 hours (again) while I slept. This morning I tried to copy/burn disc image to a DVD with Roxio Toast 7, and it stopped near the end of the burn with some kind of "error" message. So then I tried Utilities> Disc Utility> Burn icon, and followed it through. Be sure to click the DVD DL drive in the window "Burn disc in.". I had one other problem though. At the end of a 46 minute copy, it started to verify, and at the end of verify it rejected the burn. So I tried again, and when "verify" appeared, I clicked on "Skip." The disc finished burning and is doing fine and well. A long and tortuous process, but at last something works. I made several additional copies using Disc Utility. Best wishes. Chuck, Chicago.
2. Disconnect any other external devices not absolutely needed.
e.g. external USB/USB2 hard disks, other FW hard disks etc.
3 Chapter marks in transitions - minimum 2 sec from
FROM Bev.
(Not a 'guy' but I will answer!)
First, I do not think that mixing wide-screen and standard makes a difference in iDVD.
Second, you should use a better brand of DVD disk. Also, many of us have experienced fewer problems on playback with DVD-R disks. Recommended brands here are Verbatim, Maxell and Taiyo Yuden. Memorex and TDK are not consistent and may not give you a correct burn. They apparently have fewer layers in the composition of the disk. I have always used Verbatim DVD-R disks and have not had any burn problems.
Also, choose a slower burn speed, 4x or less.
Third, to determine if the iDVD project will burn properly, create a disk image file (from within iDVD, go File->Save as Disk Image) and test it. Mount the disk image and then open DVD Player (in Applications) and view your project. If it plays correctly, you can then burn the actual DVD disk from the disk image file using Disk Utility.
From. Boise, Idaho
I did everything I've seen suggested, but a friend (who used to be an Apple Genius) suggested that I do a safe reboot (by holding down the shift key until you see the spinning gear on gray background, then release, then restart when your start-up screen appears).
It worked, and I got a clean burn from iDVD.
Hopefully this can help other people.
by dheb0422
Well, I finally got it, and it was odd enough to post here incase anyone looks this topic up again. Many things were tried, including burning the unedited film, the edited film without titles and chapter markers, abbreviating the chapter markers in case length was the issue (remember the old iMovie used to truncate them when moving to iDVD?). In the process, I noticed that one, and only one, chapter marker was on the same line as the title marker. All the others were on the line above. The only way I seemed able to change that was to clip a few seconds of film. After that last clip, the offending marker took a place on the line above, as were all the others. That run published, compiled completely and burned. That's one for the books.
One user more writes
To add my experience with Multiplex Errors using iDVD (7.0.4), I recently created two iDVD projects
Video from both passed from FCE 4.01 with chapters
One project worked fine in creating disk image file
The other gave Multiplex Errors
I tried suggestions to remove special characters and no chapter marks at beginning, but nothing worked
Note that I've used iDVD for dozens of projects and this is first time I've run into Multiplex Errors
Anyway, for problem project, I tried an experiment where I removed all chapters in FCE and passed to new iDVD project
This time multiplex errors gone
So had something to do with chapters
So now I tried numerous experiments to remove individual chapters and try again creating disk image with new iDVD project
After numerous tries, I was able to narrow problem down to 1 "Bad" chapter mark
That is, when I left the "bad" chapter in my FCE project and passed to iDVD, iDVD gave multiplex error
When I removed "bad" chapter mark (and others in), no multiplex error
As a final experiment, I moved "bad" chapter mark about 5-10 sec's beyond original point and passed to iDVD, the multiplex errors now magically went away and I was able to finally create my disk image.
I have no idea why this worked, but thought I'd mention here in case someone else runs into similar problem.
Rich839
In addition to Bengt's fine advice, burning errors can occur if you have located any of your menu buttons wholly or partly outside of the safe TV viewing area. Go to your main project menu, then click on View/Show TV Safe Area, to check. Drag into the safe viewing area any buttons that are outside the safe viewing area.
Russ One - suggest this
Multiplex Error-There was an error during muxing preparation
One thing that worked for me was to export the video w/o chapter markers as a self contained movie (thereby not loosing the edits & etc). Then make a new FCE project and import that movie into a new sequence and add the chapter markers. I've used "-", "&" and "," with no problem in the chapter names. Removing the markers or exporting without them did solve the problem but renaming them with just numbers 1,2,3....5, did not solve the problem and since this problem seems to happen with with iMovie as well, it would suggest the problem is in the video or audio and in combination with the chapter markers iDVD just can't handle it. The only other possibility is that both iMovie and FCE share the same or similar chapter marker code that some how is corrupting the markers.
Summary - What to try
1. Chapters
• Only A to Z and 0 to 9 in chapter title
• No Chapter mark at very beginning of movie
• No Chapter mark in or within 2 seconds from any transition in movie
2. TV-safe area for buttons (no one outside this)
3. Safe re-boot
4. No other external devices connected - that are not needed
SDMacuser adds to this
• On #4 ... No ext. devices. Some think this applies mainly to ext. FW. Not the case. Also applies to ext. USB2 as well (not to mention flash drives too).
Do not leave 3rd party devices / camera / camcorder plugged in unless it is being used with iDvd's One Step process. Certain web cams can trigger this also (especially ones with added features like LED light/s that draw additional power from the FW or USB bus).
5. Minimum of 25Gb free space on Start-up hard disk
6. Make a DiskImage first - reduces where problem originates
7. Trash iDVD pref. file
8. Make a new iDVD project
9. Movies in project with same aspect ratio e.g. 4x3 or 16x9
10. No other programs/applications running during iDVD process. e.g. Internet, screen & energy savers
Yours Bengt W -
I go through the process of burning a DVD from a Premier Pro Project and at the end of the process I get an encoding error and the dvd does not start burning. How do I fix this?
adam@honestmusky wrote:
Yes I am using encore. I used to have no problem doing this, but I had to get a new computer and now something isn't working right.
How about some DETAILS?
-Premiere Pro Video Editing Information FAQ http://forums.adobe.com/message/4200840
Also describe the EXACT steps you take to go from Premiere Pro to Encore -
Trying to burn a playlist in itunes and i get this message at the end 'The attempt to burn a disc failed. An nknown error occurred (4450)'. This is with a new Dell laptop running windows 8. The playlist was 17 songs from cd's and itunes. Any ideas?
try this...
This is how I managed to fix the problem...and I hope this helps others in the similar situation.
I tried with another program..latest version of Nero, and this was also stopping at the 'initialising' stage. I was now lost! I thought the last resort is to give Evesham (My PC manufacturer) a buzz. They were very helpfull. Basically go into 'Control Panel', 'System', and click on the Hardware tab, then 'Device Manager'. Uninstall everything in the DVD/CDRom Drives. Then uninstall everything under the catagory IDE ATA/Atapi disk controllers. This is where my problem was, as I only had one IDE channel here. You should have 4 or 5! Reboot your machine, and everything will automatically re-load. I tried burning using Nero and it worked. Then the big test was iTunes. It worked 1st time!
I asked why the IDE channels have dissappearred, and he said sometimes uninstalling Programmes occasionally removes them.
I hope this will help others who are having problems to burn stuff on iTunes. -
I can't burn any DVD or CD - burning process interrupts before it ends
Hi everybody !
Sorry for my bad english, but I assume you're all aware about the frenches are not very good at english.
I've got the following problem: I can't burn any dvd or cd. I've already tried with different programs such as Sonic, Nero 7.0, and I Tunes, and I got every time a mistake wich interrupted the burning process before it ends.
So I don't know what to day ! I've already tried to re install the drivers, but it's didtn't change anything.
In order to help you, I've saved an error log from nero. I hope it could be helpfull to someone who could help me !
Here is the log:
moi
5C82001080000000000666822849
Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Nero\Nero 7\Core\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 02/11/2004 13:54:32
NT-SPTI used
Nero Version: 7.0.0.0
Recorder: <MAT****A DVD-RAM UJ-841S>Version: 1.60 - HA 1 TA 0 - 7.0.0.0
Adapter driver: <IDE> HA 1
Drive buffer : 2048kB
Bus Type : default (0) -> ATAPI, detected: ?
CD-ROM: <MAT****A DVD-RAM UJ-841S >Version: 1.60 - HA 1 TA 0 - 7.0.0.0
Adapter driver: <IDE> HA 1
=== Scsi-Device-Map ===
DiskPeripheral : FUJITSU MHV2100BH PL atapi Port 0 ID 0 DMA: On
CdRomPeripheral : MAT****A DVD-RAM UJ-841S atapi Port 1 ID 0 DMA: On
CdRomPeripheral : AXV CD/DVD-ROM 2.1b axvodka Port 2 ID 0 DMA: Off
=== CDRom-Device-Map ===
MAT****A DVD-RAM UJ-841S D: CDRom0
AXV CD/DVD-ROM F: CDRom1
=======================
AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 2045MB (2095084kB)
Free physical memory: 1277MB (1308144kB)
Memory in use : 37 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)
21.9.2006
CD-ROM (ISO)
21:04:46 #1 Text 0 File Isodoc.cpp, Line 6410
Iso document burn settings
Determine maximum speed : FALSE
Simulate : TRUE
Write : TRUE
Finalize CD : FALSE
Multisession : TRUE
Multisession type: : Start multisession
Burning mode : TAO
Mode : 1
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet : TRUE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE
21:04:47 #2 Text 0 File Burncd.cpp, Line 3007
MAT****A DVD-RAM UJ-841S
SmoothLink activs
21:04:47 #3 Text 0 File ThreadedTransfer.cpp, Line 525
ReadBuffer-Pipe got 81920KB of Memory
21:04:47 #4 Text 0 File Reader.cpp, Line 124
Reader running
21:04:47 #5 Text 0 File Writer.cpp, Line 113
Writer D: MAT****A DVD-RAM UJ-841S running
21:04:47 #6 ISO9660GEN -11 File Geniso.cpp, Line 3304
First writeable address = 0 (0x00000000)
21:04:47 #7 Text 0 File Burncd.cpp, Line 3301
Turn on Track-At-Once, using CD-R/RW media
21:04:48 #8 Text 0 File DlgWaitCD.cpp, Line 277
Last possible write address on media: 359844 ( 79:59.69)
Last address to be written: 318786 ( 70:52.36)
21:04:48 #9 Text 0 File DlgWaitCD.cpp, Line 289
Write in overburning mode: NO (enabled: CD)
21:04:48 #10 Text 0 File DlgWaitCD.cpp, Line 2568
Recorder: MAT****A DVD-RAM UJ-841S
21:04:48 #11 Text 0 File DlgWaitCD.cpp, Line 456
>>> Protocol of DlgWaitCD activities: <<<
=========================================
21:04:48 #12 Text 0 File ThreadedTransferInterface.cpp, Line 846
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 318787 (318787) = #318787/70:50.37
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 318785 blocks [D: MAT****A DVD-RAM UJ-841S]
21:04:48 #13 Text 0 File ThreadedTransferInterface.cpp, Line 1058
Prepare recorder [D: MAT****A DVD-RAM UJ-841S] for write in TAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc not fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 307200 653182976, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
-150 | lead-in | 0 | 0x41 | 0x00
-150 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
318787 | lead-out | 1 | 0x41 | 0x00
21:04:48 #14 Text 0 File ThreadedTransferInterface.cpp, Line 1126
Removed 2 run-out blocks from end of track 1. Length: 318787 -> 318785.
21:04:48 #15 Text 0 File SCSIPassThrough.cpp, Line 34
SPTILockVolume - completed successfully for FCTL_LOCK_VOLUME
21:04:48 #16 Phase 24 File dlgbrnst.cpp, Line 1724
Caching of files started
21:04:49 #17 Text 0 File Burncd.cpp, Line 4129
Cache writing successful.
21:04:49 #18 Phase 25 File dlgbrnst.cpp, Line 1724
Caching of files completed
21:04:49 #19 Phase 32 File dlgbrnst.cpp, Line 1724
Simulation started at 24x (3 600 Ko/s)
21:04:49 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2669
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
21:04:49 #21 Text 0 File MMC.cpp, Line 21541
Set BUFE: SmoothLink -> ON
21:10:08 #22 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
21:10:10 #23 Phase 33 File dlgbrnst.cpp, Line 1724
Simulation completed successfully at 24x (3 600 Ko/s)
21:10:11 #24 Phase 36 File dlgbrnst.cpp, Line 1724
Burn process started at 24x (3 600 Ko/s)
21:10:11 #25 Text 0 File ThreadedTransferInterface.cpp, Line 2669
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0
21:10:11 #26 Text 0 File MMC.cpp, Line 21541
Set BUFE: SmoothLink -> ON
21:12:16 #27 SPTI -1040 File SCSIPassThrough.cpp, Line 306
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1040)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x10
Sense Qual: 0x00
CDB Data: 0x2A 00 00 01 76 C0 00 00 20 00 00 00
Sense Area: 0xF1 00 03 00 01 74 5D 0A 00 13 00 00 10
Buffer x03390000: Len x10000
0x72 F1 87 E5 D3 3D 4A 96 F9 B0 73 83 D3 14 72 A1
0xF3 49 6E 93 44 25 04 6D E5 CE 44 5F 3E C6 79 47
0xDD DD EA 3A FD 71 4D 32 CB 35 F3 DF 4B 18 BD 7D
21:12:16 #28 CDR -1040 File Writer.cpp, Line 302
Illegal block size for command
D: MAT****A DVD-RAM UJ-841S
21:12:16 #29 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion
21:12:17 #30 Text 0 File ThreadedTransfer.cpp, Line 222
conversion idle, stopping reader
21:12:17 #31 CDR -201 File WriterStatus.cpp, Line 200
Invalid write state
D: MAT****A DVD-RAM UJ-841S
21:12:17 #32 TRANSFER -18 File WriterStatus.cpp, Line 200
Could not perform EndTrack
21:12:17 #33 Text 0 File MMC.cpp, Line 16273
<MAT****ADVD-RAM UJ-841S > start Close Session
21:12:30 #34 SPTI -1040 File SCSIPassThrough.cpp, Line 306
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1040)
Sense Key: 0x03 (KEY_MEDIUM_ERROR)
Sense Code: 0x10
Sense Qual: 0x00
CDB Data: 0x00 00 00 00 00 00 00 00 00 00 00 00
Sense Area: 0x71 00 03 00 00 00 00 0A 00 13 00 00 10
21:12:30 #35 CDR -1040 File WriterStatus.cpp, Line 249
Illegal block size for command
D: MAT****A DVD-RAM UJ-841S
21:12:30 #36 TRANSFER -19 File WriterStatus.cpp, Line 249
Could not perform Fixation
21:12:30 #37 Text 0 File WriterStatus.cpp, Line 258
falling back to disc fixation
21:12:30 #38 Text 0 File MMC.cpp, Line 16273
<MAT****ADVD-RAM UJ-841S > start Close Session
21:12:30 #39 SPTI -1046 File SCSIPassThrough.cpp, Line 306
CdRom0: SCSIStatus(x02) WinError(0) NeroError(-1046)
Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
Sense Code: 0x30
Sense Qual: 0x05
CDB Data: 0x5B 01 02 00 00 00 00 00 00 00 00 00
Sense Area: 0x70 00 05 00 00 00 00 0A 00 AA 00 00 30 05
21:12:30 #40 CDR -1046 File WriterStatus.cpp, Line 249
Illegal disc
D: MAT****A DVD-RAM UJ-841S
21:12:30 #41 TRANSFER -19 File WriterStatus.cpp, Line 249
Could not perform Fixation
21:12:30 #42 Phase 38 File dlgbrnst.cpp, Line 1724
Burn process failed at 24x (3 600 Ko/s)
Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.32a, size=20640 bytes, created 25/04/2005 11:03:00 (Prassi/Veritas driver for win 2K)
Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)
So, thanks to you !
See you !
RomainHi
The error log doesnt provide any very useful information.
According to this error log the simulation was running correct but the burning process was not started.
In such case its very hard to say why it happens. Possibly the drive is damage and cannot calibrate the lens properly or you use not compatible medias.
The burning process depands also on the fiels and data which youwant to burn.
Some data, CD, DVDs are encrypted and its not possible to burn and to copy it.
In other case you could also try to burn the medias with lower speed and not with 24x.
But in worth case you the drive has a malfunction and you have to replace it ;( -
"Errors found during the burning process"
Hello,
I created an iDVD project that includes:
1. 108-minute movie
2. 6-minute movie
3. 3-minute movie
4. 12-minute slide show (3 four-minute slide shows)
The project worked fine in the iDVD Preview. I then attempted to burn the DVD right from iDVD, and after 8 hours of encoding, I got the "Errors found during the burning process" message.
I've read so many posts here with a hundred different possible solutions, but what is the best place to start to try to determine what the errors are and how to fix them?
Following one suggestion, I am now creating a Disk Image first, but if errors still exist with a Disk Image, what do I do then?
I'm working on a Powerbook G4 with the iLife upgrade. Thanks for any advice.
LarryLarry,
Here's my philosophy on iDVD troubleshooting, largley based upon my experience here at this forum, with heavy doeses of input from Ken Tidwell, Len Goff, Old Toad, F Shippey, with more recent input from SDIllini, Hui Cheng, and Beverly M.......
#0 - always use "Save as Disk Image" instead of burning when troubleshooting iDVD
#1 Try the easy usual suspect fixes first! After all if these don't work you can always try the hard fixes!
Check the list on this download:
http://dvd.kentidwell.com/iDVDUOFAQ2005.pdf
But here are easy solutions IMHO:
Get free space on the startup drive -20GB recommended
Delete the iDVD plist file com.apple.iDVD.plist
Repair Disk Permissions
Clear Cache Files (CacheOutX, TigerCacheCleaner, Onyx)
Do you have 12 bit audio - check your camcorder.......if not 16 bit you will have problems
Fix Chapter Markers-don't put one at the beginning in iMovie (iDVD will do it for you)
Chapter Markers - don't put one at the end.
Chapter Markers - don't put one within 2 secs of a transition
Delete other corrupt preference files (try using Preferential Treatment)
#2 When the easy fixes don't work, you need to divide and conquer. The suspects are your a) your project media, b)your hardware, c)your system/user preferences, d)iDVD.
A good test for a&d is to build a simple test project with other photos/movies/themes/audio and see if you can "save as disk image" the test project. The iDVD4 tutorial project is great if you've ever had iDVD4 installed on your machine. If this works it suggests that iDVD is working OK, and that something in your project is causing the hiccup.
The most common problems in projects are CMs, audio and transitions. One way that sometimes clears them up is to export to full quality DV (or to tape!) and re-import into iDVD. In slideshows, funny JPEGs can bring iDVD down. The only method here is to try different groups to find the bad actor.
OK let's assume that you can't burn (I mean "Save as Disk Image") the test project or the tutorial. This suggest that your hardware/system/iDVD is having problems and your project is probably fine. Then what?
c) Hardware: if you can make a disk image but can't burn it, or it plays badly, then try creating a data DVD - if you can't do that I'd suspect your DVD drive. Try different brands of DVD-R (and I'd stick to -R, not +R nor +RW), I like Verbatim. Next on the suspect list is RAM. iDVD is the best test for RAM known to mackind. Try pulling non-Apple supplied modules and try again.
OK, let's assume you can make data DVDs, but you can't make a good disk image, and you've tried pulling all non-Apple RAM. What next?
Try creating a new user. New users have more limited sets of fonts and all new preference files and caches, not only for iDVD but for everything, and few (if any) third party plug-ins installed.
Finally try reinstalling iDVD.......
If you've done all this, a new system install might be in order, but come here first for advice from others before going that far!
john b
Maybe you are looking for
-
Regarding report for daily GRN
Sapgurus, Any report where we can see all daily stock report in MM side Thanking you
-
Purchase to Order Scenario - Partial Confirmation Issue
Hello Team, We are using Item Category with Purchase to Order Scenario. When the Sales Order is booked, Purchase Requisition is Created. Sales Order Line is linked to the Purchase Requision/Purchase Order. In this scenario, we are getting confirmatio
-
Problem with using isAuthenticate method in my applet
Hi everyone I want to be sure that everytime that I select my applet the secure channel has been opened. I found isAuthenticate method from SecurityService Interface and I think that I can use this method in my applet's select method for this purpose
-
Badi name for Sales order download from R/3 to CRM
Hi Guys, Can some one give me the badi name for below requirement. Requirement: We are downloading the orders from R/3 to CRM system.while downloading the Order history from R/3, top level VC (Variant config data) is also comming to CRM. But we want
-
Disable/Disabling "Save As" shorcut Shift+Ctrl+S
I have removed the "Save As" item from the file menu, but also want to disable the shortcut (Keyboard Accelerator): Shift+Ctrl+S Here is the code I have so far: AVMenubar avMenubar; AVMenuItem avMenuitem; avMenubar = AVAppGetMenubar(); avMenuitem = A