Unplanned Inspection Characteristics in Routing - Operation

Hi experts,
What is the use of the function Unplanned Inspection Characteristics in Routing - Operation ? Its normally grayed off.
I am aware of the same in RR of the Inspection Lot.
Thanx
George

Hello Jomy,
Ok so you were asking the same for Production order. You wrote routing operation and my mind stuck there since I read it. I was searching for it. You make good exercised to me. LOL!!!
Anyways, in the production or process order the unplanned MIC does the same task of job what it used to de in QE51N or any other RR work sheet. And you can assign the Unplanned MIC to Pro. Order itself to the relevant operation. Let it be gray there, you just follow the steps to attach an unplanned MIC to Operation in the Order, and the same will be reflated to RR screen also.
- Select the operation line item.
- Now follow the path,,, Operation->Function for phase / for operation->Unplanned Inspection characteristics.
- Now it will lead you to the same screen for unplanned characteristic as you can have in other RR work lists.
Pls revert if there is any query.
Regards,
Shyamal

Similar Messages

Inspection characteristics wrt the operation

hi friends,
my clent uses 10 operations for the production of the finished product. in 4 th 7th and 10 th operation the material passes through Quality insp stages. how can i configure it in routing.?i do not have qm module implemented in my clients company?it is in MTS Scenario for a tool manufacturing company, where quality plays a major role. please suggest ,
Regards
omkar

Dear,
If QM is implimented then proceed as below
Activate type insp type 03 in material master
Create inspection char i.e. MIC in QS21 and other master data like sampling
Create a routing with 4th, 7th and 11 operation with cotrol key having insp char tick
Assign the MIC created to differnt operation as required by QA dept
create Prod order and release. System will create INSP lot with differnt MIC
Do the inspection and proceed.

Add inspection characteristics to production order created via CO07

Hi, all.
We're creating production orders to perform production rework on assemblies using transaction CO07.
We have a requirement to inspect and make a usage decision on the reworked assembly.
Since there is no material at the header level for CO07 orders, the system isn't allowing us to do an inspection because it has no material master QA view to reference. Although the control key is marked for in-process inspection, the production order still won't allow it.
I can't add "unplanned inspection characteristics", not can I manually create an inspection lot using QA01.
Is there a way to manually force in an inspection for an operation on a CO07 order?
Thanks.
Sarah

Hi,
We cannot do a inspection for a production order unless it has material assigned to it and the material got QM inspection type relevant to that.
regards,
Lenin. A

BAPI to update Routing operations

Hi
I want to update inspection characterstics in routing operations,
can you plz suggest any BAPI to update.
Regards,
kranti

Hi Dhirendra,
I want to update Char.number,Material Insp characterstics,method and sampling Procedure.
as u mentioned in that BAPI, BAPI_QPMK_SAVEREPLICA,i have found,Material Insp characterstics,method these two parameters,
so how can i uplopad Characterstic no and sampling procedure?
Regards,
Kranti

Material routing inspection characteristics.

Hi everybody,
I just wanted to ask whether don't you somebody know some function or bapi, that allows to change the material routing inspection characteristics listed in CA02.
Thanks a lot.
Jan.

Check it here Re: bdc problem ca02

LSMW to Load - Equipment Task List/Operations/Inspection Characteristics

Hello Experts,
Any suggestions on standard LSMW load program for this. The Standard batch Input - 0470/IBIP program does not have the option to load Maintenance Package and Inspection characteristics.
Any other suggestions please.
Thanks

Hi Ananthram,
instead of using the standard batch input program, you could also create a new recording that performs exactly the tasks you need. Mark "Batch-input-recording" and click on Overview. From there, you can start recording your transactions.
I hope this helps and solves your issue.
Marc

Link between PRT and inspection characteristics in Rate Routing

I am creating an Z report to show the details of the PRT and the inspection carried out by the same.(inspection characteristics)
Suggest me any table link between two.

got the solution

How to progammatically get Inspection Characteristics from Inspection Plan

How do I programmatically get Inspection Characteristics from an inspection plan? I am currently getting inspection characteristics from inspection lots via a QM-IDI RFC call (QIRF_SEND_REQUIREMENTS_GET_DAT2), but if the Inspection Characteristic is not in an inspection lot, I don't get it via the RFC call. What BAPI/RFC/IDOCS mechanism can I use from an external subsystem (VB.NET app) to get inspection characteristics (Spec Limits, Target, Operation, Activity) associated with a material in an inspection plan?
Thanks,
Ed

The problem is the SAP system that my external subsystem (VB.NET application using QM-IDI) is interfacing with does not have inspection lots (and the customer is not willing to add inspection lots), so the QM-IDI RFC that I'm using (QIRF_SEND_REQUIREMENTS_GET_DAT2) does not return the inspection characteristics (spec limits, etc) that I require. My customer creates a reference (QP11) with inspection characteristics, then attaches the reference to a Material (QP01). When I try to get the inspection characteristics for the material via QIRF_SEND_REQUIREMENTS_GET_DAT2, I don't get the inspection characteristics because there is no inspection lot associated with the material and inspection characteristics.
The design is for my external subsystem to do the Material Inspection Characteristic valuation, and then send the valuation results back to SAP. Is there a way to get Material Inspection Characteristics and then send the results back given the SAP setup I described above?
Thanks,
Ed

QM Inspection Characteristics table

Hi,
I am designing Inspection Report for QM Module, the thing is i am unable to find the tables for the data
1. Characteristic Specifications
2. Characteristic Results
like Characteristic Related complete data. And also can any one tell me what is the relation between Operation & Charaterisitics in the Inspection Processing?
Like the table used for that !!
Waiting for ur reply....
Regards,
Srinath

Hi,
Following is the list of related tables.
QALS - Inspection lot record : This is the table where you can get all the inspection lot numbers
QAMV - Characteristic specifications for inspection processing
QAMR - Characteristic results during inspection processing
QASR - Sample results for inspection characteristics
QASE - Results table for the sample unit
QASE and QASR give the results for individual samples and partial samples
To get the operation for the particular characteristic, call function module QEEA_READ_SINGLE_OPERATION
Pass AUFPL from QALS, VORGLFNR from QAMR and PRUEFLOS from QAMR to the function module as shown below.
The FM returns the value of operation VORNR in structure e_qapo.
call function 'QEEA_READ_SINGLE_OPERATION'
     exporting
          i_aufpl            = <fs_qals>-aufpl
          i_plnkn            = <fs_qamr>-vorglfnr
          i_prueflos       = <fs_qamr>-prueflos
     importing
          e_qapo_wa    = e_qapo
     exceptions
          not_found       = 1
          others             = 2
Hope you'll find this useful.
Regards
Radhika

Related to Inspection Characteristics load issue

Hi All,
I am trying to load inspection charatceristics - please see my requirement below
Can we use the standard SAP program for Equipment Task lists to load the Inspection Characteristics associated with the Operations?
Transaction (IA01)
The program works fine for Header and Operations (One to Many, PLKO to PLPO) but does not have a separate structure for PLMK (Inspection Characteristics) but has a structure IBIPBDCD to use.
What we're trying to achieve basically is One Header, Many Operations each having many Inspection Characteristics
Also,
In the current state the program can add one Inspection Characteristic to the First operation, is it possible to add "BDC Commands" to the file in such a way to
1. "Position on particular" operation (i.e. Position Cursor and select line on screen SAPLCPDI 3400 where PLPOD-VORNR = 'xxxx')?
2. Go back to the operations screen (i.e. SAPLCPDI 3400) at the end of each Inspection Characteristic entry in order to be able to position on either the same operation to add an Inspection characteristic or to position on a different operation (not necessarily the next one)
Could you please help me with this issue?

It is possible, Get help from ABAP.
Thanks & Rgards
Rajendran

How to split inspection lot in Routing?

Dear Gurus,
Is there any chance to create splitting inspection lot in the middle of a routing process ?
My scenarios are :
I have a BOM with finished product X and Component A
I also have Routing AA with 2 operation inside, Operation 1 for Production Process, while Operation 2 for Quality Control ( in 1 Routing )
The flow production is the BOM Component A will be issued into Operation 1(it will be issued in 1 PC), after that the output from Operation 1 will be Product X in many pieces (for example 10 pcs and also define as 10 batch number)
Now the problem is, when the 10 pcs product X have to go into the operation 2 is there should be define per inspection lot for every batch number (so in this case it should create 10 inspection lot) for QC Operation
What i know now is the inspection lot already generated for inprocess inspection (for all operation), but it is just 1 inspection lot for 1 production order
I need to create inspection lot from receiving product X after operation 1 equal to the amount batch created from finishing operation 1 ( 10 pcs = 10 inspection lots), but still inside the routing process and then process it into operation 2 (QC station), how to do that??
is there anyone who can help to solve this problem?
Regards,
Rizki

Hello Shantilal,
once you have created an inspection point you cannot change the data -> This would lead to an inconsistency simular to the following case.
This can lead to dumps if you change the data of an existant inspection point in customizing. SAP recommends creating a new inspection point definition.
The reason is the fact that key fields can be maintained via customizing, a change of these key fields means that the system will try to sort inspection points with the old key fields using the newly defined key fields.
Example: Customizing -> Define Identifier for Inspection Points
(1) indicates the position in the key
Inspection point definition for Z01
Key 1 (Original Key)
(1) Text length 18, (2) Text length 10, (3) Number length 10, (4) Number length 3
Is changed to Key 2
(1) Date, (2) Time, (3) Number length 10, (4) Number length 3
As you can imagine if the plan tries to select previously created inspection points this will lead to a dump, because the key has been changed.
In this case you need to create a new inspection point definition Z02 with the new key and create a plan which also uses the new inspection point type.
Appartently you have done so, but the plan assigned to the inspection lot uses the previous inspection point definition, if you were to change the inspection points this would also lead to a dump.
I hope that this answer helps you to understand why the requested function is not possible.
Regards,
Isabelle

Inprocess inspection characteristics missing

Dear all
i assigned 03 inspection to a material but forgot to assign inspection characteristics, lot has been created at the time of the creation of production order. now i want to do the inspection but there is no assigned characteristics. i have assigned characteristics to that material in routing but how to get the effect on that lot to get the characteristics without changing order
is there any option plz guide me

Dear Nasir,
You have to try to read the Production Order master data through Production Order --> Functions --> Read Master Data. This is the way you can reset your lot Because In process inspection lot is attached with Production / Process Order. Other wise cancel the production order and create the new one. I hope this will work.
Best Regards,
Ibne Khalil

Routing Operation item field update in configurable material

Hi All
Material is a configurable material ,which is having a selection options in a sales order and based on the selection options there is characteristics BOM quantity gets updated based on the formulae.
If you go to routing and double click on the operation to see the details , you will see the unit of measure conversion with the header and Operation fields. I want BOM quantity should get updated in the operation field (UMREN).
I was using the Reference characteristics with PLPOD table and UMREN field to update the value in the UMREN field. And i created a procedure with a logic and is assigned to configuration profile and the Routing operation.
Process is MTO process, Production order is generated when the sales order is created. i checked in production order after creating a sales order, UMREN field is not updated and dont know what where i am doing mistake and i also checked in the Routing Master Data there also its not updating.
Above mentioned is not an requirement but to calculate the costs accurately, we have to approach this way.
Please suggest.
Thanks,
Quantum

hi all,
this problem is solved...its was a simple thing...go to extra in operation tab of routing, then go to references and there is an option of unlock....
and bingo...the problem is solved.
best regards,
Maulin

Inspection characteristics based on material and goup counter

Hi,
Do we have some function module which would give us inspection characteristics based on material and group counter. I have gone through many posts in this regard but find answers to get inspection characteristics based on inspection lot number.
I do not want to get into quality at all. Is there a FM to get the inspection characteristics based on material and group counter or any related tables would be of gr8 help. T-code QP03 takes material and group counter as input and displays the inspection characteristics. Any input in this regard would be of great help.

Hi,
Use tables MMAPL , MAPL and PLMK as per your requirement.
Thanks,
Vijay

Date format in Master inspection characteristics

Hi All
I have a requirement where my user wants to enter the date format in the master inspection characteristic. For example we want to add date of manufacture and the date of expiree as a inspection characteristics and during the results recording they want to enter this characteristics in a date format.
MY question is can we have a master inspection characteristic with a date format, if so what all the settings are required.
Please suggest.
Thanks,
Quantum.

>
quantum wrote:
>Can i use characteristics in the inspection plan instead of the master inspection characteristics. I am using Work bench transaction code CWBQM to create an inspection plan.
Direct characteristic you can't use in inspection plan. If you want to use characteristic in IP then create chara. (CT04), then assign this charac. as class chanr.(QS21) in MIC. Now you can use this MIC in inspection plan.
Hope this helps.
Thanks!!!

Unplanned Inspection Characteristics in Routing - Operation

Similar Messages

Maybe you are looking for