Unreadable Files After installing Leopard UPDATE

Okay, so I went through a bunch of problems and though I should share my experience to hopefully help others with the same problem.
Installed leopard after being told it had no conflict with FCP6. Well, it did, as i couldn't open any of my older project files and got the dreaded error message: Unreadable or may be too new for this version of Final Cut."
Tried many things, like trashing preferences, reinstalling FCP6, opening files different ways. None were successful, heard I had to do a clean install, which I didn't want to do. Went to the genius bar, spoke with tech support and browsed these forums for another way.
After realizing that there wasn't any way for me at leats I decided to do a clean install, and IT WORKS now.
Bad points: H
1. Have to back up all your content on harddrive.
2. Spend a lot of time installing everything again
3. Spending time updating everything again.
Good points:
1. You can work again with FCP and Leopard
2. The computer runs faster.
3. You realize a lot of junk you didn't need to begin with and you have a nice new clean computer.
Hopefully this will help others.

Also my boss figured out another solution. On the computer that I was getting the other files from, I had to have it export the FCP file in an XML format. Then once I opened the XML file on my computer I just reconnected all of my media and it worked.
For some reason the intel/G5 switching didn't like something about FCP6 project files but it worked when the file is in XML format.

Similar Messages

UNABLE TO OPEN FCP 6.02 PROJECT FILES AFTER INSTALLING LEOPARD!

**Unable to open FCP 6.02 project files after installing Leopard**. Tested and found that the files can be opened on another computer with OS 10.4.10, but not OS 10.5. Spoke to apple support many times, and have tried reinstalling FCP, but it didn't work.
Apple is now saying to erase my HD and reinstall from scratch. This presents a problem since i have software installed but no disc due to a move, (they are deep in offsite storage).
Anyone have this problem? Anyone know a fix?

Lynne,
There is a section in the manual on the migration tool... I don't have my machine fired up right now so can't direct you to the exact page. I think a search for migration or migrate should do it.
Two other things to try:
1. There have been numerous reports that Quicktime 7.3 is what is killing older projects. According to one of the third party program makers Apple re-wrote Quicktime changing the null value to Zero from minus-one. I'm not a code junkie so can't vouch for this but the upshot would be, go back to Quicktime 7.1 or 7.2 not 7.3
2. There is a Quicktime plugin called "Perian". For lots of people it has caused numerous problems.
Look for Perian on your machine and if you find it, drag the app to the trash... re boot and try again.
Of course the ultimate solution would be to reinstall Tiger, Final Cut Studio 2 and Quicktime 7.2. So far the most stable combined setup for me and lots of others on G5 machines.
36 degrees and thunderstorms with sleet here this afternoon. The door on my storage unit is staying closed.
Message was edited by: John Criswell

Can't open any excel files after installing Snow Leopard

I can't open any excel files after installing Snow Leopard. Is anyone else having this problem?
I have a standard iWork '08 install. Has anyone experienced? And better yet, know of a fix?

Welcome to Apple Discussions
Most users who have had a problem opening Office files with the iWork apps after upgrading to Snow Leopard have the problem fixed by updating to the latest versions. For iWork '08 that is Pages 3.0.3 & Numbers 1.0.3. For iWork '09 it's Pages 4.0.2 & Numbers 2.0.2. I don't use Keynote, but it should also be updated. If you're not running the latest versions & Software Update says your software is up to date, make sure the applications are where the installer initially put them. The updaters are very picky. If the location is not where the updater is programmed to look or if the folder doesn't have the name the updater looks for, it will not work. The applications cannot be renamed or moved. They must be in the iWork '08 or iWork '09 folder in Applications. That iWork folder must be named iWork '08 or iWork '09. If it doesn't have the '08 or '09 Software Update won't find them & the updaters won't work.

After installing two updates, I cannon create .pdf documents as the window says "Missing PDF Maker Files." I've uninstalled Acrobat and re-installed twice, same problem

After installing two updates, I cannon create .pdf documents as the window says "Missing PDF Maker Files." I've uninstalled Acrobat and re-installed twice, same problem. How do I correct problem?

Thank you. I googled my problem and got good answers involving making changes to my Office settings - which worked.
Sent via the Samsung GALAXY S® 5, an AT&T 4G LTE smartphone

I can't seem to install flash player on iPhone or MacBook after snow leopard update...why??

I can't seem to install flash player on iPhone or MacBook after snow leopard update...why?? How can I fix this?

Flash Player doesn't work on IOS devices.
On Macbook, try un-installing and then re-installing.
Adobe Flash Uninstaller
Adobe Flash Player

Cd burning issue after installing and updating snow leopard

After installing and updating snow leapard to the latest version, the cd burner for i-tunes quit working. it says" burning disk initializing" then "burning disk finishing" comes up with the error "the attempt to burn a disk failed. the disc drive didn't respond properly and can't recover or retry. Any suggestions to fix this problem?

First try other disks, brand new, then try another brand, then consider backup user files and (clean and polish then) c booting off the 10.6.3 disk and simply reinstalling OS X then updating to 10.6.8 again.
Hopefully this should fix the issue in OS X software, you may have to reinstall certain third party software again that it's kext files got kicked out of OS X by the reinstall.
If you get hung booting at any time, simply hold the shift key down and then update your software then reboot normally

Error Messages After Installing Leopard 2

After installing Leopard from the Install DVD, I used Software Update to update to 10.5.1, and updated QuickTime, etc. I also ran Cocktail, the Leopard edition. The Hard Drive checked out OK. When I ran Repair Permissions in Disk Utility, I got a number of error messages. One set starts like this: "Warning SUID file "System/Library/Private Frameworks/DiskManagement.framework/Versions/A/Resources/DiskManagementTool" has been modified and will not be repaired."
There are a number of messages like this. What shall I do?

Download and install this update, even though you've already updated.
(26492)

Finder not working after installing Leopard!!!

Hi everyone.
I'm getting a strange Finder behavior on my Intel iMac (not the newest version) after installing Leopard. The thing is, after instalation, when I start the computer, the top bar on the screen starts blinking, and there's no way to open a Finder window. And it stays like that forever! I tried to open Finder from the Dock, but the blue dot of the active programs blinks 3 or 4 times and then disapears. Plus, the only way to access the Apple logo on the corner to switch the computer off or restart it, is by opening one other program from the dock (in this case I have Safari running), because this way the top bar stops blinking.
So, I thought I should try to update Leopard to 10.5.1, and this could solve the problem. But no. It searches for new software updates, tells me that there are new updates, but I cannot see them nor install them!
This is really weird and annoying!
Anyone had this problem? Please, help me.
P.S.: Yes, I've tryed a second install of Leopard. Same thing!

anamorphis wrote:
Hi everyone.
I'm getting a strange Finder behavior on my Intel iMac (not the newest version) after installing Leopard. The thing is, after instalation, when I start the computer, the top bar on the screen starts blinking, and there's no way to open a Finder window. And it stays like that forever! I tried to open Finder from the Dock, but the blue dot of the active programs blinks 3 or 4 times and then disapears. Plus, the only way to access the Apple logo on the corner to switch the computer off or restart it, is by opening one other program from the dock (in this case I have Safari running), because this way the top bar stops blinking.
So, I thought I should try to update Leopard to 10.5.1, and this could solve the problem. But no. It searches for new software updates, tells me that there are new updates, but I cannot see them nor install them!
This is really weird and annoying!
Anyone had this problem? Please, help me.
P.S.: Yes, I've tryed a second install of Leopard. Same thing!
Do NOT install any updates until you resolve the problem, which is unrelated to any updates. Updating a computer that is not working correctly will only make the problems worse, never better.
If this is the second install, was it on an erased HD or did you import your previous programs, etc?
It sounds like you might have some errant 3rd party software running.
Did you run a disk check and file permission verify/repair before installing?
Check your startup program window and remove everything there. Write them down so you can put them back later.

After installing Leopard I cant

After installing Leopard I cant upload pictures through myspace I have even tryed firefox and it doesnt work I also you safari . I called apple and they said something about a plug in issue. Has anyone else had this problem.
Just wondering?

I had installed Snow Leopard on my iMac 24" 2.4GHZ Intel machine. Previously everything had been working fine prior to my install. Coincidence being what it is, after I installed SL from DVD my menu bar items in the top right were not showing up and then my CD/DVD drive was not working. Would say that it can't read the inserted disc and my options were to choose ignore and eject.
I chose Ignore and went to Disk Utility and it could see the blank DVD I had inserted. But I could not burn the disc.
*Due to me having two issues at the same time, this complicates my ability to pinpoint what the solution was, but here's what I did and now everything is fine*
Before everything granular, I tried installing from SL disc again, in case that had been an issue...when that didn't work then...
First I removed a series of suggested .plist files that pertain to the menu bar, finder, clock, etc... That was for my menu bar issue (which didn't fix it by the way)
I then used disk utility from the SL DVD using that as start up disc, yes it loads fine. Verified and Repaired Disc permissions and drive. No issues.
I ran software update and installed 10.6.1 (still no fix to either problem)
I ran firmware update using the hold power button process during startup
(still no fix to either problem)
I reset the PRAM using boot up key sequence...still appeared to be no fix.
Then one more complete shut down and reboot...VOILA! *EVERYTHING REPAIRED*!!!
So I have no idea WHAT did it, or WHY. However, that process now has me burning DVDs successfully and I have all my menu items back.
I know it's not the most helpful response, but I can tell you everything works fine now.

Powermac g4 shuts down during start up after installing Leopard and upgrade

I have a powermac g4 (agp), 1ghz, 120gig hd
I successfully installed Leopard. After install the updater came up so I updated the files. I think they were OSX update, quicktime, itunes, and a couple of others I can't recall. I was prompted to restart for updates and when I did it will get to the white screen with the grey apple and spinning wheel then it just shuts off. I have tried to start it up several times and it does the same thing each time. I can't start with the leopard disk since I can't get the dvd drive to open without it running. I've looked at other similar posts on this subject but don't see any that are similar to mine. Any help would be appreciated.

Hi, Claire -
I can't start with the leopard disk since I can't get the dvd drive to open without it running.
Couple of ways to work around that -
• Restart or boot the machine, immediately press the mouse button, keep it held down. This is a hardware command to the Mac to eject all removable media, which should open the drive tray. Insert the disk and close the tray, restart and press the C key.
• Try restarting or booting the machine, then immediately press the Option key (ideally before or simultaneous with the startup chime), keep it held down. This should bring up Startup Manager (a vivid blue screen with a few large icons showing). Once Startup Manager has fully loaded, press Command-. (Command-PeriodKey). This should open the optical drive tray. Insert the Leopard disk and close the tray; wait a bit for the drive to spin up; then click the circular arrow icon on the left. This will cause the machine to rescan the available buses and find the Leopard disk. Once that has displayed, click it to select it and then click the straight arrow icon on the right. It should now boot to that disk.
Article #HT1310 - Startup Manager: How to Select a Startup Volume
powermac G4 (agp/sawtooth), 1ghz....
The fastest G4 (AGP), aka "Sawtooth", machine shipped was 500MHz. If your machine is 1GHz, then it has either had a processor upgrade, or it is a later model. It helps us to know which it actually is. These articles can help you identify it -
Article #58418 - Power Mac G4: How to Differentiate Between Models
Article #42739 - Power Mac G4: How to Differentiate Between Models (part 2)
The fact that it may have an AGP graphics card does not make it a G4 (AGP), or Sawtooth, model - all G4's after the G4 (PCI) model shipped with AGP graphics cards, including the Quicksilver and MDD models.

Disk permissions problem after installing Leopard

Hi!
I performed a Repair Permissions after installing Leopard. Firstly, I noticed that this procedure took a lot longer than before the upgrade. I also received the following error messages -
Repairing permissions for “Macintosh HD”
Warning: SUID file "usr/libexec/load_hdi" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/DiskManagement.framework/Versions/A/Resources /DiskManagementTool" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/DesktopServicesPriv.framework/Versions/A/Reso urces/Locum" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/Install.framework/Versions/A/Resources/runner " has been modified and will not be repaired.
Permissions differ on "private/var/log/secure.log", should be -rw------- , they are -rw-r----- .
Warning: SUID file "System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/readconf ig" has been modified and will not be repaired.
Warning: SUID file "System/Library/PrivateFrameworks/Admin.framework/Versions/A/Resources/writecon fig" has been modified and will not be repaired.
Warning: SUID file "usr/libexec/authopen" has been modified and will not be repaired.
Warning: SUID file "System/Library/CoreServices/Finder.app/Contents/Resources/OwnerGroupTool" has been modified and will not be repaired.
Warning: SUID file "System/Library/CoreServices/RemoteManagement/ARDAgent.app/Contents/MacOS/ARDAg ent" has been modified and will not be repaired.
ACL found but not expected on "Applications".
ACL found but not expected on "Library".
Permissions repair complete
What does all this mean? How can I fix it?
Thanks.

You suggest I reinstall all of Leopard and then update to 10.5.1?
No. Download and install the standalone 10.51 updater without reinstalling the entire OS.
I found 2 Remote Desktop updates (Client and Admin) - version 3.2. Are these for Leopard?
Use the client version.
How will this help my problem?
Those are status messages. You don't have a problem.
(26178)

Mail wont open after snow leopard update

Mail refuses to open after update,when initated it flashes in the tray then disappears,has apple a fix for this problem?
Or admits it exists.
Thanks

Mac OS X v10.6: Mail.app won’t open, or "You can't use this version of Mail…" alert after installing Security Update 2012-004:
http://support.apple.com/kb/TS4424?viewlocale=en_US&locale=en_US
Fellow user Grant Bennet-Alder offers this solution:
Some users have reported this problem if the Mail Application has been moved out of the top-level /Applications folder, or duplicated in another location.
When the Security Update is done, the old version of Mail is disabled.
The solution has been to:
1) make certain Mail is in the /Applications folder
2) There is no other copy anywhere else.
3) Once steps 1 and 2 have been done, Manually download and re-apply the Security Update (2012-004) by hand.
Security Update 2012-004 (Snow Leopard)
If the Mail.app has been LOST, it can be re-installed by applying the 10.6.8 version 1.1 combo update. But this update is quite large and it is usually not necessary:
Mac OS X 10.6.8 Update Combo v1.1

After installing Leopard, my G4 will no longer boot in OS 9.22. (Classic still works, but I need it to boot in OS 9.) Any clues about what the Leopard installer might have done to my machine that rendered OS 9 boot unusable? What can I do to fix it?

After installing Leopard, my G4 will no longer boot in OS 9.22.
(Classic still works, but I need it to boot in OS 9.)
Any clues about what the Leopard installer might have done to my machine that rendered OS 9 boot unusable? (And what can I do to fix it?)
Details:
G4 Gigabit Ethernet
Boot ROM version: 4.2.8fl
Accelerator card added: 1.6 MHz
1.5 Gig Ram
I have erased the partition that had Leopard installed on it.
I zapped the pram.
In Open Firmware, I "reset-nvram", and then "reset-all"
I tried to reinstall G4 FW Update 4.2.8, but that must be done when booted from OS 9, and of course, that's the problem: it won't boot into 9.
I tried restarting from 9.2.1 DVD.
I tried restarting from an external firewire drive containing OS 9.2.2.
I tried moving a fresh OS 9.2.2 system folder into an empty partition on an internal hard drive. (Partition was created WITH OS 9 drivers installed.)
All attempts to boot into OS 9 give me the same results - grey screen - no spinning beach ball, no icons or logos - just a blank grey screen.
This machine still works fine in OS 10.3 and 10.4, and it worked fine for many years booting into OS 9, until I installed Leopard, and I haven't been able to boot into OS 9 since then, although I have done considerable research online and tried many things.
I have since learned that this machine does not support Leopard - 10.5. Fine, but how did it break 9.2.2?
Any help greatly appreciated.

Thanks for checking in, BDAQua.
Problem solved.
In the docs that came with my Powerlogix accelerator card, I found this sentence buried:
"If you reset the PRAM, the NVRAM code for OS9 compatibility is cleared, so you will have to boot from the Firmawre Update CD and perform this process again in order to boot in OS9."
The "process" it's referring to is the process of setting up the NVRAM for booting into OS9 from the CD.
Fortunately, I was able to find the disk, and it worked as expected. I can now, once again boot into OS9.
Conclusion: My (unadvised) attempt to load Leopard on this old machine apparently reset the PRAM on the accelerator card and cleared the NVRAM code for OS9 boot. Although I did attempt to reset the NVRAM via Open Firmware, it did not reset it on the accelerator card.
So, thank you BDAQua, for your "Ah yes" . . . that's all I needed to steer me in the right direction.
Gratefully,
tupester

MacBook Pro hanging with blue screen and spinner after installing Software Update

Hi I was wondering if someone could help me with this current issue. Just a few hours ago I finished reinstalling Mac OS X Snow Leopard in my MacBook Pro. I performed a clean installation as part of a yearly spring cleaning that I do on all my systems to keep them optimized. So there was I downloading some software updates which included the combo update of OSX 10.6.8 and others. The updates finished downloading and the system logged out to install the updates, when the updates finished installing my MacBook proceeded by logging out into a blue screen and show a gray spinner similar to the one seen when you start your Mac. Here's the problem after 2 hours the system is showing the spinner and the blue screen, I think that my computer has just hanged in the reboot process.
I was wondering what should I do? Do a force restart? Or leave it overnight?
Also, where can I find any information on what error is causing this issue?
I appreciate your responses and help.
By the way, I installed Mac OS X from a USB stick that has the original image of the disk installer that came bundled with my computer.

Kappy wrote:
Force a shutdown. Do not restart yet, but first do the following:
Repair the Hard Drive
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Next, boot into Safe Mode then restart normally.
Hi Kappy,
Checked the hard drive after forcing a shutdown and booting from my Snow Leopard Installer USB Key and the status of the HDD says "Verified". I ran the repair and the volume was repaired successfully. Clicked on "Verify Disk" and it says "Macintosh HD appears to be OK". So I ran a second repair and again no errors were reported.
As suggested I booted back again in Safe Mode and restarted normally. All software appears to have been installed successfully. But I don't understand why my computer hanged and showed the spinner after installing the updates in the blue screen that appears just before rebooting. I am aware that the system shows that spinner after a OS update but the longest it lasts is 30 seconds at the most in my previous cases.

My external drive went dead after installing Leopard

Hey guys
I'm very bummed out, my external HD went dead after installing Leopard on my Dual 2.3 GHz PowerPC G5. It was working perfectly fine before, had not a single problem with it but now, I've just lost all my work. I tried Disk Utility from the disc with no luck, it gave tons of errors and it say it couldn't be repaired. Now, it doesn't show up at all. Every single time I connect it I get a message saying the disk I inserted is not readable by the computer. This is a 200GB Maxtor external drive. Is there anything I can do to fix it? Any hardcore Software to retrieve my files? I'd appreciate if anyone can help me with this.
Thank you in advance

Movies are currently a one time download. Because of this, it is your responsibility to back them up so when something like this happens, you can simply copy them over the new drive.
You can't download them again with purchasing once again.

Unreadable Files After installing Leopard UPDATE

Similar Messages

Maybe you are looking for