Unsteady clips

I have managed to get the video on to dvd, in the correct aspect ratio. (I got a sony dealer to do it for me, for now, so I still don't understand how to do it myself, and couldn't get mydvdedit to work, as it quits every time I try to set aspect ratio)
Problem: a few clips vibrate. I think they are all still-frames, either extracted as stills from the clips, or imported as jpegs. When the dvd plays, at these clips, they wobble, more or less violently, up and down. Other stills, imported or freezeframed, are ok.
Any suggestions?
Thanks
Mike

Stills extracted from Video will need to be De-Interlaced.
There is a de-interlace filter in FCE just for the job.
Al

Similar Messages

Is there a way to steady a clip that was shot unsteady

I am trying to use a clip that someone shot. The clip is moving around quite a bit, is there a way to take the unsteadiness out of this clip? I thought about slowing it down, but I don't think I would like the looks of that? any suggestions?
thanks
ruez30

Take a look at iStabilize.

Camileo Clip - shaky video

I bought the clip to use for recording my walks. I tested it using the stabiliser and holding the clip as I walked along, but the resulting video was jumping around so much it was unwatchable! How on earth can I overcome this problem? If I do 'clip' it to myself then the shaking will be even worse as at least in my hand its steadier. I even tried video stabilisation software but the original footage is so unsteady the software cant cope!

Well, I wrote already in your other thread about this camcorder.
The Camileo clip its a fun, party camcorder designed for shooting small segments of an party event. You should not expect too much from this fun camcorder.
As far as I know this camcorder supports the image stabilization
The electronic image stabilization helps you to minimize the shaky video effect but you of course you should not expect too much from a 60 camcorder.

Cs5.5 losing ability to manipulate clip envelopes, with 5.5 reactions also

I'm trying out the 30 day demo of Audition 5.5 - there can be some advantages to having this beside old trusty and capable 1.5, even before it's finished. It is a lot faster, and has some advantageous VST plugins, even if it's not quite finished.
However, a session where I was using clip volume envelopes became unable to manipulate them. Holding the cursor over the envelop shortly gave a tooltip saying Volume, but no prior points showed, and I couldn't add any new ones.
After the requisite hair pulling, I tried deleting preferences (under Win7, in c:\Users\Username\AppData\Roaming\Adobe\Audition, you rename or delete the folder named 4.0). This recovered Clip Envelope abilities.
In the same area, there are also Track Envelopes, which may in future be a better way to work most of the time, as you can turn them off. Howeverr this functionality is a bit unsteady to use in the 5.5 initial release.
-- If you use the pulldown to change to Off or Read while playing the track, the setting will be ignored. You have to stop playback before changing the setting, then start it again. Then track envelopes are appropriately read or not read.
-- I have some feeling that it was originally playing with this pulldown that zapped the ability to use clip envelopes as above, so that might be looked into.
Very happy to keep hearing from Durin and others on the Adobe team. This is a big plus for 5.5 itself.
I'm getting along with most things, while still on the learning curve.
One thing that still bothers a lot is the action of the Play Head. I can't seem to get it to return to its original position upon stopping playback, as earlier Audition did. A marker is the only way work can be done, and that's not the best. The other odd thing is the ghostly quasi-marker that appears if you click during playback. This disappears on stopping, so it's not clear what it's useful for, if it is tantalizing.
5.5 seems generally very fast and pretty solid -- appreciating the framework you are freshly building.
Regards,
Clive

Thanks on the CTI/cursor tip -- I'd managed to miss that across several trawls of Preferences. Probably missed by not scanning the CTI acronym.
When set to return to initial position on Stop, the function of the ghost cursor is clear in that mode.
Function looks unfinished as yet for the non-return mode -- presumably when setting the ghost cursor by a click, that should be the new return point, but it isn't; the ghost just disappears on Stop then.
That visit to Preferences, dealing with its acronyms, got me to try to the joys of multispeed JKL key scrubbing -- that's pretty nice.

Partner application and web clipping.

Hi All,
I am trying to add an external application (say my.yahoo.com) to a webclipping and its throwing the below error in the application log.
WC-517 : SSL handshake failed with the url ...
I have checked the file ca-bundle.crt and the certificates are in place. Does anybody know how to go about debugging this problem as I am quite new to portals and at my wits end to solve it.
Also I would be greatful if anybody can suggest me the steps on adding an Apex application configured as partner application with SSO authentication to a web clipping.There seems to be little or no-documentation at all in this regard(as far as my search goes).
Thanks in advance
-Venkat

I finally got it working by VERY CAREFULLY reading the instructions in the install.txt document in the SSO SDK package. You have to set up the partner application with a new schema in the login server database, and run the regapp.sql script AFTER editing it to insert data from the Login Server Partner Application admin screen. After you register the partner app in Portal, it gives you some info (site token, listener token, encryption key, etc). You have to MANUALLY copy these and paste them into the regapp.sql script, then run the script in the partner app schema. Make sure you don't confuse capital I with numeral 1 (like I did, since Oracle so nicely uses a non-serif font where you can not tell the difference).
Also make sure you copy the exact values for these parameters into your code when you use the SSOEnabler class. The listener token was very confusing since different documents appear to disagree on whether it should include the partner app name or not. It does require the partner app name:
app-name:hostname:port
hostname and port are for the web server that is handling http requests for the login server (usually your main portal web server).
John H.

Loading sound clips in my swing application

I have searched all the forums, din't find what i want.
I have many small sound files to be played in my application. Even on mouse Pressed, Drage etc etc....
Now I was looking for a better way of Loading the Sound files in memory as the application starts.....
If I use the Clip Interface of javax.sound and initilize them and open a stream, invoke the open() method, and store it in hashmap. So that when ever i need that file i will lookup for that clip and trigger the start() method which actually plays the sound. IS the approach the right approach, will not the Cip object keep the IO handle open, I have nearly 40 Clips to be loaded.
Can any one suggest me the better way of implementing this.
TIA
Zoha

As far as I know,there is no facility for detecting mouse scrolling wheel in JDK 1.3.
Check it in the later releases of JDK.

Problem with clipping and concerned objects (or rather their color)

Greeting everyone,
I hope i don't bother you with things that are already known or, in the end, are a product of my own stupidity ;P
My problem is the following:
I was working on a neat design for a list. The first version (without clipping) looked like this:
[http://www.7pics.info/?image=GHApp-Gradient-Mobile-HowItShouldBe_2c5.jpg]
As you can see on the bottom, the list was on top of all graphical elements.
And because this looks stupid, i decide to simply clip the list via "clip: Rectangle{...}".
Well... turns out it's not as easy as i hoped it would be; all of a sudden the list looks like this:
[http://www.7pics.info/?image=GHApp-GradientProblem-Mobile-1_fb7.jpg]
From the left to the right you see the following: first picture is what you'd see initially, from the second to the last i scrolled down one entry each (respectively moved the list up 30 pixels).
Further scrolling down doesn't change the look, it stays like in the last picture.
Scrolling up again delivers the same image, but in reverse order.
The clipping seems to change something in the style of the list elements.
To be more specific, the gradient of a single element is now applied to the whole list.
here is a Listing
//the group which contains the list and the clipping
Group{
     clip: Rectangle {
          x: 0, y: 70
          width: PublicVars.screenWidth, height: 210
          fill: Color.BLACK        //which color i use doesn't change the look
     content:[
          createChoicesList()
//create a box for each entry and add text from a string sequence "results"
createChoicesList():Node[]{
      for(result in results){
                       singleField = Group{
               Rectangle {
                    fill: LinearGradient {
                         startX : 0.0
                         startY : 0.0
                         endX : 0.250
                         endY : 0.250
                         stops: [
                              Stop {
                                   color : Color.LIGHTBLUE
                                   offset: 0.0
                              Stop {
                                   color : PublicVars.coolGradientBlueTransparent
                                   offset: 0.5
}I have no clue why this happens. I tried to shift some things around, thinking it had to do something with the order of some elements but... it didn't change anything.
Another thing i noticed afterwards:
If i run the App as a desktop program, the gradient effect is all messed up. but this time it doesn't matter if I clip the list or not:
[http://www.7pics.info/?image=GHApp-GradientProblem-Desktop-1_d5e.jpg]
The gradients are totally misplaced and if I scroll down they move and appear/disappear randomly across the list entries. sometimes the highlighted elements even look like this:
[http://www.7pics.info/?image=GHApp-GradientProblem-Desktop-2_89f.jpg]
Any Ideas?
P.s.:
Could it be that retrieving the resolution of a mobile device via
"var screenWidth = java.lang.Integer.parseInt(FX.getProperty("javafx.screen.width"));"
isn't very accurate?
If i use the values i get from this method for the desktop application, the screen will be smaller than in the emulated mobile phone
Edited by: Mr._Moe on 04.09.2009 21:31

Not sure about your problem, but I can answer your last question: you can now use the [javafx.stage.Screen|http://java.sun.com/javafx/1.2/docs/api/javafx.stage/javafx.stage.Screen.html] class to get screen dimensions.

How can I display & split the audio & video from the same digitized clip?

I digitized a scene into iMovie that I edited on a professional system which I don't have access to anymore. The whole scene is 1 clip. Now I see a few tweaks that I want to make, so I was hoping to do them in iMovie.
I want to "pull up" the audio in one section - meaning I want to take cut about 20 frames of audio from the end of a shot, and then move all the other audio up to fill the hole. To compensate for the missing 20 frames, I'll cut video off the head of the next shot. Some call this prelapping. Some call it an L-cut. Some call it asymmetrical trimming. Either way, I can't figure out how to do it in iMovie.
My clip appears in the timeline as one track - a single track that contains the video and 2 audio tracks. How can I display the audio that's tied to the video on its own track? Then I think I could split audio & video wherever I wanted and trim things up - but I can't figure out how to do it.
Am I asking too much of this software?
BTW, I never see the option to "Split audio clip at playhead". I'm not displaying clip volume or waveforms. Choosing to display waveforms doesn't show me anything. Maybe iMovie thinks I'd only want to see waveforms of audio that isn't tied to my video-and-audio clips?
Thanks in advance for any help...

Jordon,
"Am I asking too much of this software?"
No, you're not.
You first want to select your clip(s) and choose Advanced>Extract Audio.
This will copy the audio from the video clip and place it on one of the two separate audio tracks while lowering the audio level to zero in the original video track.
You can now edit and move the audio independently of the video.
With the audio clip selected, you'll find you now have access to Edit>Split Selected Audio Clip at Playhead.
Matt

How can I move clips from one library to another? Clips are still in original drive and not in new drive.

I am using iMovie 10.0.7 on a 1-week old iMac 27" running Yosemite 10.10.2. I migrated from iMovie 9 on a 2008 iMac running Snow Leopard and updated the libraries and events, etc.
I have two external drives connected via USB. I want to move / consolidate the library and clips from one of the external drives to the new iMac's 3TB fusion drive. This is to make room on the external drive to run Time Machine backups.
Apple's instructions on managing libraries and moving/copying clips/events tell me to drag to move between libraries and to Option-drag to copy. However, simply dragging only copies. I find that if I Command-drag the events/clips, I can "move" them. But when I look outside iMovie in the Mac OS X Finder, the event folders and clip files themselves are still sitting in the original drive.
I'm very perplexed as to how to really move the clips and event structure. Should I manually copy the clips and event folder structure outside of iMovie? I worry I will mess up iMovie's internal record keeping and folder structure information.
Thanks in advance.

Ahh, Ok. I actually had to go to Lynda.com to watch a training video of this highly bassackwards maneuver, but now I have it. In other words, while the intuitive thing is to make a new event to hold the clip you want and then open the old event and drag the clip into it's new event, the only way to accomplish this maneuver is to NOT create a new event, but rather, go to the clip AFTER the one you want to move, select it and then Right-Click on it and select SPLIT EVENT BEFORE SELECTED CLIP (or go to FILE>SPLIT EVENT BEFORE SELECTED CLIP). Then you wait a few seconds while the program thinks a bit (no feedback it is doing this - just a pause) and then it automatically creates a new event with the clip you wanted. Now just double-click the new event and name it something meaningful.
Thanks for your help!

How to play one clip multiple times at the same time?

I am writing a little game where a certain sound has to be played quite frequently. I load it as a Clip and play it with
myClip.setFramePosition(0);
myClip.loop(0);If the sound has to be played again but is still being played by another event, the setFramePosition() method resets the sound and the first playing instance is cut off.
A workaround would be that each object that needs to play this sound would get its own copy, but that is not feasible due to heavy memory consumption.
So here it goes: How can I play a single sound multiple times at the same time? Is that possible?
Edited by: andrasz on Feb 27, 2009 12:37 AM

If the sound has to be played again but is still being played by another event, the setFramePosition() method resets the sound and the first playing instance is cut off.
A workaround would be that each object that needs to play this sound would get its own copy, but that is not feasible due to heavy memory consumption.
So here it goes: How can I play a single sound multiple times at the same time? Is that possible?Ummmm, if you're using a clip, you'll have to maintain one copy per object that needs to play the sound concurrently. You could keep one master copy, and then create copies of the clip as necessary to play them, and then just dump the copies to decrease memory consumption.
A second idea would be to write your own Clip class. Esentially, all you would need to do is dump some sound data onto a TargetDataline to play it. It'll handle the buffering and playing at the correct speed itself. If that's all you did, you should be able to dump multiple times from the same instance and play it multiple times.
Obviously, that's just a theory. In practice, it may not work that way...

How can I create a video clip that has multiple copies of the same subject playing at the same time? Basically like one person became 50 backup dancers!

Hello Everyone,
I am trying to create a single video clip where my original subject (dancer) is multiplied on the screen many times. Basically I am trying to create a background video for a dance team and want to make it look like an army of the same person dancing behind them. Amy guidance would be great!
Thanks
Madisonman 2013

Motion ($50) can do this with a replicator.
Russ

Managing Family Clips on a Mac - Help - New Mac User

I am new to the Mac and am looking for the most efficient way to manage my media. I have 300+ files that are in the later stages of being converted to Mp4. All of the files will reside in /Movies/imported.
What should I do next?
Should I import everything into iMovie using the "move" option?
Should I import into Itunes and only import Movies I want to edit or post online. I am assuming this option will give me duplicates.
I think iPhoto can manage movies thoughts ?
My goal is to have only one local copy of the files (30+ gig), have access through iTunes, and finally iMovie access to edit and post online without importing and duplicating data.
Does any of this make sense ? I think I am OCD...
What would you do with 30gig of family clips?
null

Hello Richard,
I would place all the MPEG4 clips into iPhoto, where you could sort them to subject, year, etc. Then you could make a copy by dragging a clip to your desktop, leaving your original in iPhoto. Work with that copy in iMovie.

How do I move multiple clips at once in the project rather than one a time?

I know how to cut and then paste to move one clip within the project to a new place within the project, but how do I move a group all at once rather than one at a time?

This did not help and that did not work. I had already tried that Holding down either the command key does "highlight" multiple items but then you cannot move those items to a new spot.

HT4589 How do I move video clip clip up or down after setting letterbox, i used to be able to do this until i upgraded to 10.0.6

I used to be able to manually move my video clip up and down in the event the browser using one of the settings. It was a vertical settings that i would use to pull a video clip down after i applied a letterbox to the clip, so I could see the top of the the video clip that got blocked out by the letterbox. Still looking no luck....I used to be able to do this just upgraded to FCPX 10.0.6 now i dont have the setting..

think i might have solved my own problem the feature is not there i have to upgrade again to 10.0.7...this is getting annoying...

How do I sync multiple audio clips to one video clip?

I have video (with stereo audio from a camera mic), and for each take, there are also four additional mono audio tracks that line up with it. It was footage shot outdoors in the city, so I guess the filmmakers just wanted to have as many options for sound mixing as possible given how much background noise there would be. I have tried selecting the video clip and the four audio clips at once and selecting "synchronize clips," but it doesn't work. It spits out a synchronized clip that seems to have converted two of the mono tracks into one stereo track... and then disregarded the remaining two mono tracks. It's a mess. It's likely someone else will fine tune the audio once I'm done cutting the video together... but I'd like to get all the audio tracks properly synced from the start. Thanks for any help you can offer.

Do you mean manual syncing? I've been reading this thread about workaround, which aren't working for me: http://forums.creativecow.net/thread/344/21236
But the question they are asking is the same one I am asking. Isn't this a typical situation, having multiple mics for one camera? For example, if someone filmed a concert with one camera but used both the camera audio, and ambient mic, and a mix from the board, then that would be 3 audio tracks with 1 video track. I'm in a similar situation, and I'm finding it hard to believe that FCPX isn't equipped to edit this way. There must be some way to get one video clip (with reference audio) to sync with four audio tracks.

Unsteady clips

Similar Messages

Maybe you are looking for