Up: error fetching interface information: device not found

Hiya,
FIrst off... apologies that I've already made a thread on this - but I still haven't found a fix
I'm thinking I might have more luck in the Networking section
Here's my original post: https://bbs.archlinux.org/viewtopic.php?pid=827958
I appreciate it

Maybe U need change MAC address of your network card.
ifconfig eth0 hw ether 00:00:00:00:00:01 .
Where the 00:00:00:00:00:01 is the MAC of your desktop with windows.

Similar Messages

My computer wont start up says boot device not found how can i fix that

I HAVE AN HP PROBOOK 4430S
SERIAL NUMBER {Removed for privacy}
THE ERROR MESSAGE IS BOOT DEVICE NOT FOUND HOW CAN I FIX THAT ERROR

Hi:
Go into the BIOS and run the hard drive diagnostics test and see what that reports.
Sounds like the hard drive failed.
Paul

1045: Interface IFocusManagerComponent was not found.

i get this error
"1045: Interface IFocusManagerComponent was not found."
any ideas why im getting this error ? ive searched around but only get flash cs5 related info
thanks in advance

Hi?
Having the same problem!
How to add library fds2_sdk\frameworks\libs\fds.swc.

Start-up problem with hp pavilion dv6t-7000‏: "Boot Device Not Found. Hard Disk (3F0)" error

I started getting start-up problems with my hp pavilion dv6t-7000‏. It happens intermittently.
The boot error is:
Boot Device Not Found
   Please install an operating system on your hard disk.
   Hard Disk (3F0)
   F2 System Diagnostics
   For more information, please visit: www.hp.com/go/techcenter/startup
Could a faulty BIOS update cause this problem?
Anyone else who may have experienced a similar problem?
I'd appreciate any help about this problem. Thanks.

Hi
Please find the link given below might help you to fix your issue.
Resolve Boot Device not Found Error Message
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

HP Device Not Found Error when trying to print or scan wireless- HP Officejet Pro L7590

Have had HP Officejet Pro L7590 All-In-One Printer for years. Always worked fine and I had no issues printing via wireless connection. Several months ago.. Possibly after a Windows 8 update. From Windows 8 to Windows 8.1 I have not been able to use the printers wireless feature. When I try to print or scan it shows the printer as offline. Also get an error message that tells me "HP Imaging device is not found". I can still print when connected to USB. Cannot scan or use features of the HP software suite. I have tried several times to correct. Reloading the software and drivers several times, but no success. I just tried again and was able to print the test page wireless, so got all excited and thought I fixed it. Then tried to print something and got the same error message I have seen in the past. I have talked to certain supports saying that it may be a firewall setting within Windows. Any other suggestions? Thanks

Hi @rfjones002,
Welcome to the HP Support Forums! I see you are not able to print or scan wirelessly to your HP Officejet L7590 and your computer running the Windows 8.1 Operating system. You get a 'Printer offline' or 'HP Imaging device not found' errors.
I would like you to start with the steps listed below:
Hold down the Windows Logo key () on the keyboard and the 'R' to open the run box, type %temp%
Delete all files and folders from the temp folder. Choose skip if any pop ups appear saying any of the files could not be deleted
Uninstall the software again - Uninstall the Printer Software Instructions
When the uninstall has completed restart the computer
Follow these steps to reset the registry settings and options for Windows Installer.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
In the Open box, type
msiexec /unregister
and then click OK.
Hold down the Windows Logo key on the keyboard and the 'R' to open the run box
In the Open box, type
msiexec /regserver
and then click OK
*Note: there is a space between the c and the /
If you have any difficulty with this step, please use this link to perform it another way. Restarting Windows Installer
Run Disk cleanup from Accessories\ System Tool < How to Delete files using Disk Cleanup
Download and install the latest version of Adobe flash player http://www.adobe.com/support/flashplayerflashplayer/downloads.html
Perform a clean boot > How to perform a clean boot in Windows
Download the following SP40669 File Download - if this does not download and or install please proceed to the next step.
Turn off the Real-Time Scanning and Firewalls; The image below is a McAfee example, if you have a different antivirus program and need help disabling Real-Time Scanning and Firewalls let me know.
- Image source
Now you can go ahead and download and install the software here >
HP Officejet Pro Full Feature Software and Driver
If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know if this was successful! I will watch for your reply.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

I'm receiving error Boot Device Not Found and Hard disk not exist when I boot up my laptop

I'm receicing the error Boot Device Not Found when i power on my HP G60-235DX laptop. After following HP's recommended troubleshooting steps, I receive error Hard disk not exist. Hmmmm....that's a little concerning. My guess is I need a new hard drive? I have the 17 recovery disks I made when I setup this laptop, however I'm not sure if they will resolve this issue. Any suggestions?

One of 3 things has happened, listed from most likely to least likely
1. Hard drive has died, replace it with one of the same size or larger, then use the HP recovery discs to re-install windows.
2, The motherboard has serious problems. (Replace the notebook)
3. The hard drive cable that connects it to the motherboard has somehow failed, not very likely. (replace the cable)
Replace the hard drive with a new one and use your recovery discs to get Windows back on it.
Here is your service manual, will show you how to replace the hard drive
http://h10032.www1.hp.com/ctg/Manual/c02985882.pdf
Recovery Instructions for Vista
Recovery Instructions for Windows 7

Boot Device Not Found Error Message

I've had my laptop since May 2011. HP Pavilion dv6
Quad-Core AMD Phenom II 2.2 GHz
DDR3 SDRAM 8 GB
500 GB Serial ATA 7200 rpm hard drive.Originally Windows 7 64-bit upgraded to Windows 10 64-bit One morning I turned on my laptop and I received the following error. The laptop lives on my desk, hasn't undergone any major changes, and I haven't moved or dropped it. I've run every diagnostic test from the F2 menu. The hard drive and memory both passed, the system tune up passed, and I've restored the BIOS to the default settings with no changes. If I hold the power button and restart the laptop usually on the 2nd or 3rd attempt the system will start normally with no issues and continue on as if nothing is wrong. This is a helpful work around but it doesn't solve the problem which is a bit of an annoyance and leaves me worried that eventually it might refuse to start at all. Thinking that a system restore might help I ran a recovery and brought it to an "out of the box" state. After that failed I decided to go ahead and upgrade from Windows 7 to Windows 10. I performed a clean install keeping none of my programs or personal files. Despite a successful Windows 10 install I still receive the same error every time I restart. The short version:When I turn on my laptop I encounter a Boot Device Not Found Error Message.My hard drive passes diagnostic tests.My laptop will start eventually if I continue to power cycle it.

@pkharel ,
Hello and thank you for posting on the HP support forums. So that I can better help you here with this hard drive issue . Can you explain what diagnostic you ran on the hard drive.
Did you run the diagnostics from the BIOS?
HP Notebook PCs - System Diagnostics (F2)
HP PC Hardware Diagnostics
If you have attempted the diagnostics from the BIOS and are not finding the Hard drive. See if you can find the hard drive in another computer. If you can not find it using another computer replace the drive. If you can and it is not located on your notebook then you have a possible issue with the motherboard.
First thing I would do is try and restore your BIOS first.
Restoring the BIOS
After attempting this and you still can not find the Hard drive and you can see it in another system please contact HP phone support for repair options.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
If the hard drive is not detected in another system then replace hard drive.
Please click the "Thumbs Up" on the bottom right of this post to say thank you if you appreciate the support I provide!
Also be sure to mark my post as “Accept as Solution" if you feel my post solved your issue, it will help others who face the same challenge find the same solution.
D5GR
I work on behalf of HP

"boot device not found. please install an operating system on your hard disk error on Dm3 1030us

Hi
I have the following computer:
name: hp pavilion Dm3 1030us
serial number: {Removed for privacy}
product number: VM073UA#ABA
when i boot up my laptop it says "boot device not found. please install an operating system on your hard disk."
this laptop does not have a cd drive but I do have a external one. since it does not have a cd drive therefore they didnt give me a recovery cd.
It had Windows 7 on it.
Is there a way to get the issue resolved

You would have to call in to HP tech support ( 1-800-HP-INVENT) and have them order you some RCD's.
I work for HP.
Please click the White Kudos star on the left to say thanks.
Please mark Accept As Solution if this resolves your issue.

Please help me with this error: "Apple application support was not found... Error 2"

Can anyone please help me with this error: "Apple application support was not found... Error 2"
I've followed the instructions by removing all Apple files from my laptop, but when I reinstall the iTunes software it still comes up with this message:
"Apple application support is required to run iTunesHelper. Please uninstall iTunes, then install iTunes again. Error 2"
Thank you

iTunes "Apple Application Support is required... Error 2" and possible fix.
I know this is a bit late but I came accross this thread trying to resolve this same problem and came up with a solution that worked for me, so thought I would share it here too. I hope it helps someone else.
I just resolved this on Win Vista (should apply equally for Win7 too). Please uninstall iTunes before proceeding though. I'll walk you through the process I followed, if you like you can jump straight to the Solution section.
Problems:
The initial error during the installation of iTunes was:
An error occurred during the installation of assembly 'Microsoft.VC80.CRT,version="8.0.50727.4053",type="win32",publicKeyToken='1fc8b 3b9a1e18e3b",processorarchitecture="x86". Please refer to Help and Support for more information. HRESULT:0x8007054F
The error (after installing iTunes) when trying to run iTunes was:
Apple Application Support is required to run iTunes. Please uninstall iTunes, then install iTunes again. Error 2 (Windows error 2).
After trying various fixes around the forums I came across this MSKB article, which relates to the first installation error:
http://support.microsoft.com/kb/2688946
This lead me to trying to install MS Visual C++ but I received the following error trying to install that:
Error 1935.An error occurred during the installation of assembly ‘Microsoft.VC80.ATL,type=”win32”,version=”8.0.50727.762”,publicKeyToken=”1fc8b3 b9a1e18e3b”,processorArchitecture=”amd64”’. Please refer to Help and Support for more information. HRESULT: 0x80070BC9. Assembly interface: IassemblyCacheItem, function: Commit, component: {837BF1EB-D770-94EB-A01F-C8B3B9A1E18E}
Note: The installation of VC++ rolls back when it fails.
Solution:
Through this error I found this MSKB article:
http://support.microsoft.com/kb/946414
The Automated MS "Fix It" msi package didn’t work.
Note: Please backup your registry first (see the above MSKB article for instructions).
I opened the registry and (as instructed in the MSKB article) deleted the following keys:
HKEY_LOCAL_MACHINE\COMPONENTS\
PendingXmlIdentifier
NextQueueEntryIndex
AdvancedInstallersNeedResolving
Reboot and reinstall iTunes.
If it helps you please like this so others can find it.

HP 3050A : Device Not Found on Network

Hi,
Laptop Model: MacBook Air
Operation System: OSx Lion 10.7.3
Printer Model: HP 3050A
Router Model: Linksys WAG160N
WiFi Security Protocol: WPA
TCP/IP IPv4 Protocol: DHCP
Firewall Software: None
I have manage to connect the printer to my WiFi network as the blue indicator is ON and got an IP 192.168.1.104 with Excellent signal strength on the printer. But when follow the HP Setup Assistant I unpluged the USB then I got stuck with the following error message:
Device Not Found on Network
The wireless network settings were successfully downloaded to your device. However, your Mac was unable to locate the device on the network.
Please make sure that:
• Your Mac is connected to a wired or wireless network that has access to your device.
• Your device is connected to the wireless network "speedy".
Click "Retry" to attempt to connect again using the current settings. Click "Go Back" to enter different settings.
I also tried to ping the printer IP but no success
Aliss-MacBook-Air:~ ali$ ping 192.168.1.104
PING 192.168.1.104 (192.168.1.104): 56 data bytes
Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
Request timeout for icmp_seq 2
Request timeout for icmp_seq 3
ping: sendto: No route to host
I am able to print using USB without any problem, but the WiFi never success! Please help!
Regards

Hello,
Thanks for the post. With this one, we may a couple of issues. I've included a link below with some excellent information regarding network connectivity. I might suggest that we start there and try to determine if it's the printer, the MAC or the network. Good Luck!
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c02731071&tmp_task=solveCategory&cc=us&dlc=en&la...
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

What do i do if my computer says boot device not found

I turned on my computer and all it does is pop up a screen says boot up device not found please install operation system what do I do to fix it

may i have some more information about the product you have? check if there is some external device connected, and check for HDD self test in BIOS. if test passes without any error and there is no external device or disc on ODD. you may need to re-install OS.
Regards,
WW
“I am an HP Employee“
***** Click the KUDOS star on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem***

Problem with Home Sharing. Getting the error "The Requested URL was not Found on this Server"

I recently purchased an iPhone 5. As I do with all of my AppleTVs, iPads, iPods and an iPhone 4 in my home, I connected the 5 to my home network and accessed the shared video library using home sharing. My iTunes library is roughly 85% iTunes purchases, a handful of videos taken with iOS devices, and some video ripped with Handbrake. All of these videos work fine on all devices in my home except my new iPhone 5. When I access the shared video library on my iPhone 5, all of the textual data for all of the videos appears, however, I can only get the iPhone to play 1 video of the dozens in my iTunes library. When I try to play any other, I get the error, "The Requested URL was not Found on this Server."
Interestingly, only one video in my entire shared library displays the artwork associated with it in my iTunes library on my iPhone 5, and that's the one I can stream without a problem. Even more interestingly, that video I am able to stream was ripped using Handbrake (there are a number in my library ripped using Handbrake, but just this one will stream to my iPhone 5 for some reason).
I'm using the latest version of iTunes (10.7) on my home (iMac) computer (running OSX 10.8.2- Mountain Lion)and of course iOS 6 on the iPhone 5. I've tried resetting my iPhone several times as well as restarting my iMac which holds my iTunes library.
Does anyone have any ideas as to what's going on?

Can you see if you can view index page from a browser on iPhone.
Have you seen live streams working from a different computer...
if not then check if a proper crossdomain.xml file in its place(webroot folder).

'Error loading plugin: Plugin file not found' message on ONLY 5 sites, but all others OK. Help, please!

Hi Again!
I posted this problem here before, but since I really need to access the sites that receive this error message in less than a month, I had to re-post; hopefully someone who didn't see it before will see it & have a solution for me.
Here are the details: I'm running windows 8.1 & I use Firefox 33.1.1, Pale Moon 25.1.0 or Opera 26.0 as my browsers, (I have IE installed & up-to-date, but I never use it). I followed the 10-point checklist on Adobe & everything was done, except for "uncheck Hardware Acceleration" in Flash 'Settings'; I tried to uncheck it on this site, where it's indicated, as well as in my 4 browsers when I'm doing something that uses Flash, but no matter how hard I try, I can't 'uncheck' the check mark in that tiny box! Since this error problem only affects 5 web sites, & I can watch streaming media on all other sites, I don't think it's an issue.
Here's how this problem began: I was watching a live, streaming nest-cam on 5/09/14 around 11:00AM, (yes, I DO know the exact time & date, because it happened so suddenly while I was watching this website that I'd been watching since the end of February, 2014), when my screen went black. I thought it was probably an Adobe Crash, but when the usual Crash Report window didn't show up, I just closed Firefox & reopened it, expecting to resume watching the nest-cam. When I went back to the site, I got the black screen with the "Error loading plugin: Plugin file not found" message. The chat portion on the site still works, though. I know there are other sites with this nest-cam feed, so I started trying them, but it took several tries for me to find one that didn't get the error message! I posted this problem on "Windows BBS" forum, & someone else posted that the same thing happened to them AND on the same sites! They didn't have a solution, either. I cleared my cache, rebooted my PC & even did a System Restore, but whatever happened in that brief second made using ONLY 5 sites impossible. Here are the sites that receive the error message:
http://pixcontroller.com/eagles, (but I CAN go to http://pixcontroller.com, but there isn't any streaming media)
http://cbslocal.com/eagles
http://westmorelandconservancy.org/BlueBirdwebcam-1.htm
http://wildearth.tv/cam/pittsburgh-bald-eagles, (I get the error message on ALL cams on this site)
http://aviary.org/BE-NestCam1 (I get the error message on ALL cams on this site)
Now if any videos from the 5 websites above are uploaded to YouTube, I can watch them perfectly...no error message if I watch the videos elsewhere. Luckily, I found Ustream, & they have most of the nest cams I watch, but I need to fix this issue, because it's nearing nesting time! I'm an amateur nest-watcher & it's vital that I have access to these 5 sites, so if anyone knows how to fix this, PLEASE tell me!
Thanks for taking the time to read my post.
All suggestions/solutions are gratefully accepted.
Thanks in advance for your help!
DogPal

File Not Found Error in Welcome Screen
07-Nov-2013 10:25
Tags: #dreamweaver_cs6_update
Help please!
Live preview also not working.
I have exactly the exact problem described below but do not have a folder with the same name as the volume created under the volume. Please can someone help - I've tried everything. This problem only happened when I upgraded to Dreaweaver CC!
"On launching Dreamweaver on your Macintosh if your Welcome Screen is not loading and if you see a "File not found" error, please check if you have a folder with the same name as your volume created under the volume. For more info on this please go through the attached pdf document. Other dialogs/panels in dreamweaver that will be blank due to this issue are Jquery Swatches panel, Adobe Edge Webfonts tab in Manage Fonts dialog,W3c Error Info dialog, Externalise Javascript dialog and svn revert dialog. After following the changes mentioned in the attached document please check all the affected dialogs/panels to confirm everything is working as expected."
Thanks,
Martin Bond
[personal information removed by moderator]

TS1369 Hello! I have an Ipod Shuffle 2nd Generation and it is not recognized by my Windows 8 based laptop. An error message of 'USB device not recognized' is shown. I have the latest ITunes version installed, and tested the dock in other pc's.

Hello!
I have a problem connecting my Ipod Shuffle 2nd generation to my Windows 8 based laptop. The computer doesn't recognize the Ipod and issues an error message saying 'USB device not recognized'. I tried uninstaling ITunes(latest version) and all other Apple software and reinstaling it back again, checked my USB hubs in the 'Device Manager' section of the Control Panel, you name it.
I could really use some help solving this.
I've turned to the troubleshooting section in Apple Support but it has nothing concerning situations in wich the device isn't even shown in the 'My Computer' folder.
Help a brother out, will you???

Found a solution in another forum http://en.kioskea.net/forum/affich-63733-ipod-not-detected-on-computer (a few posts down).
It was for an IPOD so you can see those details in the link.
Found how to reset a shuffle and inserted it into these instructions - did not have to follow his last steps.
- Turn off computer.
- Plug Shuffle into usb.
- Then you must reset your shuffle
To reset iPod shuffle:
Disconnect iPod shuffle from the computer (if connected).
Move the switch on the iPod shuffle to the OFF position. Note that when iPod shuffle is off, the green stripe by the switch is not visible
Disconnect iPod shuffle from the computer (if connected).
Move the switch on the iPod shuffle to the OFF position. Note that when iPod shuffle is off, the green stripe by the switch is not visible.
- Start computer and it should install the usb driver for the ipod automatically.
- Your i pod will say do not unplug so don't. then open itunes and it will be there.
I did not have to do these thing below – did not get error message and shuffle was displayed in Itunes. / LMc
Just remember to not only eject ipod from itunes but stop usb.
Go to the program icons near the clock and right click the usb icon and "safely remove hardware" will appear and click it.
Stop it and select "apple ipod".

I am trying to install adobe livecycle designer es4 trial version on my computer and i keep getting the message Error 13.11 Source file not found: c:\ verify that the file exist. I have tried to install on both windows 7 and windows 8 and i still get the

error 13.11 Source file not found verify that the file exsist

Try a more recent version of my advice. The "for older video cards version" may work when the default version doesn't.
For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) release as a workaround for installation or performance issues, or compatibility with QuickTime or third party software.
Your library should be unaffected by these steps but there are also links to backup and recovery advice should it be needed.
tt2

Up: error fetching interface information: device not found

Similar Messages

Maybe you are looking for