Update stuck at terms & cons page
Updated to ios7 - made me change my id password, then once I get to the terms and conditions pages agree or disagree I cant get past that page. if connected to itunes it sees everything fine on the ipod touch. Turn it on & off still stuck. Any ideas?
Have you tried resetting it?
Reset: Press and hold the Sleep/Wake button and the Home button together for at least ten seconds, until the Apple logo appears.
Similar Messages
-
IOS 7 update stuck at terms and conditions
I have updated my ipad and now it is stuck at terms and condiotions and cannot be restored because is says i must turn off find my i pad before i can restore it. but since it is frozen at the terms and conditons screen i can not turn of find my ipad and so it just sits
Hello queeny5,
You can force it into recovery-mode; then you can restore it to get past the part that you are stuck at.
iOS: Unable to update or restore
http://support.apple.com/kb/HT1808
Thanks for using Apple Support Communities.
Regards,
-Norm G. -
IOS 8.0.2 update stuck on terms & conditions
I Have a 4th gen iPad, and downloaded 8.0.2 today. It shows as downloaded in the software update setting. When you choose Install Now, Terms & conditions pops up, I choose Agree, it asks if I'm sure, I say yes, and then the Terms & Conditions box just sits there. Choosing Agree does nothing and the update doesn't progress. I have rebooted several times to no avail. Anybody have any ideas?
Hey Lexivor,
Thanks for the question. After reviewing your post, it sounds like you are not able to update the iOS. I would recommend that you read this article, it may be able to help you resolve or isolate the issue.
If you can't update or restore your iPhone, iPad, or iPod touch
Thanks for using Apple Support Communities.
Have a nice day,
Mario -
I am trying to update my iphone 4s to ios7. It is stuck on the terms & conditions page and will not move on even if I agree or disagree. Any help?
this did not help me. Agree/disagree/turn off/turn on/ try again. Nothing gets it off the initial Icloud terms and privacy policy agree/disagree page. The phone is really of limited usefulness, being stuck on that page.
-
When trying to do an update for Settings on my iPad I had to change my password. Having done that I am now stuck at 'Terms and Conditions My iPad is locked down it will not let me 'agree' and I can't get out of the procedure.
Please help/
KathReset iPad and continue with update
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
TS3694 Updated iPad to iOS7 and page has frozen in Terms and Conditions. Help?
Just updated iPad to iOS7 and page has frozen with Terms and Conditions. How do i move on?
Reset iPad and continue with update.
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
App Store stuck on a certain page
I have an iPhone 4S, and the app store is stuck on a certain page. When I go to the Featured section, all I can access is the Vampires section that's currently on the App Store. I can access Categories, Top 25, Search, and Updates fine, but I can not get back to the normal view for the Featured section. Any ideas on how I can fix this?
I found a way to resolve the issue:
1. Close the App Store from the multitasking bar.
2. Sign out of the iTunes account from the Store section in the Settings app.
3. Sign back in.
I tried just closing the App Store from the multitasking bar and it didn't work, so I think the key is to sign out of the account and then sign back in. -
Help! I cannot access anything in adobe story. It is perpetually stuck on the loading page. I tried deleting my history and using a private browser page. Nothing is working.
Hi,
This may be an issue with the Flash Player or the Browser. First try updating to the latest version of flash player. You can install the latest one from here: Adobe Flash Player Install for all versions<https://get.adobe.com/flashplayer>. Then try to login again. ?Can you also try a different Browser to see if that is the issue?
Thanks! -
Hi,
I am upgrading the OS of my iPhone5 to iOS7 directly from the device.
It downloaded and started upgrade. During the upgrade process I got stuck in 'Terms & Condition' for iCloud.
I clicked on 'Agree' buttom multiple times. Still itnstallation is not moving forward. It always remains in the same page.
Now I cannot come out the installation process. Even the 'Disagree' option is not taking me out from the 'Terms & Condition' page.
What may be the possible reason? Am I going wrong anywhare?
Regards,
RajeshThere are various solutions to this posted in this discussion: https://discussions.apple.com/thread/5321627?start=0&tstart=0. Perhaps you'll find one that will work for you.
-
Stuck on the loading page for 5 hours
My Macbook Pro is stuck on the loading page since 4 this afternoon and nothings has change since tthen, I try to close it, reopen it and nothing happen, I even try to plug it and nothings happens, I don't know what to do. If someone can help me that would be really nice.
Take each of these steps that you haven't already tried. Stop when the problem is resolved.
Step 1
The first step in dealing with a startup failure is to secure the data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since the last backup, you can skip this step.
There are several ways to back up a Mac that is unable to start. You need an external hard drive to hold the backup data.
a. Start up from the Recovery partition, or from a local Time Machine backup volume (option key at startup.) When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.” The article refers to starting up from a DVD, but the procedure in Recovery mode is the same. You don't need a DVD if you're running OS X 10.7 or later.
b. If Step 1a fails because of disk errors, and no other Mac is available, then you may be able to salvage some of your files by copying them in the Finder. If you already have an external drive with OS X installed, start up from it. Otherwise, if you have Internet access, follow the instructions on this page to prepare the external drive and install OS X on it. You'll use the Recovery installer, rather than downloading it from the App Store.
c. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, start the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
d. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
Step 2
If the startup process stops at a blank gray screen with no Apple logo or spinning "daisy wheel," then the startup volume may be full. If you had previously seen warnings of low disk space, this is almost certainly the case. You might be able to start up in safe mode even though you can't start up normally. Otherwise, start up from an external drive, or else use the technique in Step 1b, 1c, or 1d to mount the internal drive and delete some files. According to Apple documentation, you need at least 9 GB of available space on the startup volume (as shown in the Finder Info window) for normal operation.
Step 3
Sometimes a startup failure can be resolved by resetting the NVRAM.
Step 4
If you use a wireless keyboard, trackpad, or mouse, replace or recharge the batteries. The battery level shown in the Bluetooth menu item may not be accurate.
Step 5
If there's a built-in optical drive, a disc may be stuck in it. Follow these instructions to eject it.
Step 6
Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to start up, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can start up now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
Step 7
If you've started from an external storage device, make sure that the internal startup volume is selected in the Startup Disk pane of System Preferences.
Start up in safe mode. Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Post for further instructions.
Safe mode is much slower to start and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
The login screen appears even if you usually log in automatically. You must know the login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
When you start up in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, the startup volume is corrupt and the drive is probably malfunctioning. In that case, go to Step 10. If you ever have another problem with the drive, replace it immediately.
If you can start and log in in safe mode, empty the Trash, and then open the Finder Info window on the startup volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then restart as usual (i.e., not in safe mode.)
If the startup process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
Step 8
Launch Disk Utility in Recovery mode (see Step 1.) Select the startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it may produce. Look for the line "Permissions repair complete" at the end of the output. Then restart as usual.
Step 9
If the startup device is an aftermarket SSD, it may need a firmware update and/or a forced "garbage collection." Instructions for doing this with a Crucial-branded SSD were posted here. Some of those instructions may apply to other brands of SSD, but you should check with the vendor's tech support.
Step 10
Reinstall the OS. If the Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
Step 11
Do as in Step 9, but this time erase the startup volume in Disk Utility before installing. The system should automatically restart into the Setup Assistant. Follow the prompts to transfer the data from a Time Machine or other backup.
Step 12
This step applies only to models that have a logic-board ("PRAM") battery: all Mac Pro's and some others (not current models.) Both desktop and portable Macs used to have such a battery. The logic-board battery, if there is one, is separate from the main battery of a portable. A dead logic-board battery can cause a startup failure. Typically the failure will be preceded by loss of the settings for the startup disk and system clock. See the user manual for replacement instructions. You may have to take the machine to a service provider to have the battery replaced.
Step 13
If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store, or go to another authorized service provider. -
How do you get pass the Terms & Conditions page while downloading iOS7. Nothing happens when press AGREE
Reset iPad and continue with update
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
Please help me with my ipad that is stuck on terms and conditiolns when I tried to install iOS7
Reset iPad and continue with update
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected. -
Update multiple records on one page php/mysql
Hi folks,
I am trying to adapt a page to offer the option to update multiple records on one page.
The intention is to edit FAQ categories which are contained in a table with just two fields - the category and an id.
The page lists each categories in a form with a submit button which is then repeated for each record in the recordset.
Unfortunately my plan didn't work and only the first record updates as intended.
Can anyone suggest how I can make it work?
Here's the code I have so far.
************** The Update Code *****************
$editFormAction = $_SERVER['PHP_SELF'];
if (isset($_SERVER['QUERY_STRING'])) {
$editFormAction .= "?" . htmlentities($_SERVER['QUERY_STRING']);
if (!isset($mm_abort_edit) || !$mm_abort_edit) {
if ((isset($_POST["MM_update"])) && ($_POST["MM_update"] == "form1")) {
$updateSQL = sprintf("UPDATE faq_categories SET category=%s WHERE id=%s",
GetSQLValueString($_POST['category'], "text"),
GetSQLValueString($_POST['id'], "int"));
mysql_select_db($database_con_mysite, $con_mysite);
$Result1 = mysql_query($updateSQL, $con_mysite) or die(mysql_error());
$updateGoTo = "faq-category-edit.php
if (isset($_SERVER['QUERY_STRING'])) {
$updateGoTo .= (strpos($updateGoTo, '?')) ? "&" : "?";
$updateGoTo .= $_SERVER['QUERY_STRING'];
header(sprintf("Location: %s", $updateGoTo));
************** Update Code Ends *****************
************** The Form *****************
<form name="frm_editcategory" id="frm_editcategory" method="POST" action="<?php echo $editFormAction; ?>">
<?php do { ?>
<fieldset>
<input name="id" type="hidden" value="<?php echo $row_rs_faqcategory['id']; ?>" />
<input name="category" type="text" class="formrightcolumn" value="<?php echo $row_rs_faqcategory['category']; ?>" />
<input name="save" type="submit" class="submitbutton" id="save" value="save" />
</fieldset>
<input type="hidden" name="MM_update" value="form1" />
<?php } while ($row_rs_faqcategory = mysql_fetch_assoc($rs_faqcategory)); ?>
</form>
************** The Form Ends *****************
Cheers
DaveWhat does debugging tell you? What's the value of each of the variables? Did you try using regular echo statements to monitor what's going on? That's what I always do whenever I am stuck in my PHP coding.
-
IPhone stuck on security question page
I Have a pc, iPad and iPhone 4s
on pc and iPad I can purchase apps through app store , but on iPhone I am prompted for the 4 security question . After submitting answers the iphone screen will not move forward and am stuck with question / answer page I have update os
I have restated iphoneEllennet wrote:
So did my iPhone 4 yesterday, I felt helpless that time and ask all of my friends, some of them told me to try iPhone Data Recovery. My iPhone worked normal again after I used the software. I found it very easy to use because I am a computer newbie. So you don't need to worry that it stuck on the apple logo. Just have a try.
Don't worry, just follow these steps to fix iPhone stuck at Apple logo
=> First of all Start your Computer and then connect with Internet connection, now Download the latest version of the iTunes application
=> Now install the iTunes application in your System and connect your Device with computer via Data cable
=> Now connect your Device with iTunes application and then Tab on summary option, see in the left side bar of iTunes
=> Now Select restore option from iTunes and then confirm the Restore Message for better results. After this unplug your Device and Restart it
I hope that will surely
Thank you... -
Update vanished my previous home page - how to restore?
I got an update message. I let it update. My previous home page vanished. Now I just have the very basic page and seem to be stuck with it. I am, alas, elderly and not very computer savvy. I'd like to get my page back. Please advise.
I thanks for your answer.
Where do you get the "Recycle" ??
thx in advance
xavier
Maybe you are looking for
-
is there a way to import "Jewish Holidays" into iCal? On Gmail calendar or Outlook you can add the Jewish Calendar so all Holidays are added each year, is this available for iCal too?
-
Graphs show random characters instead of image in 11.1.1.6 post upgrade
After upgrading from 11.1.15 to 11.1.16 any new or existing analysis with a graph is showing a block of random characters instead of the graph. For example, a simple line chart shows: 6NABcmBe33NAV9cyxeT52IcJe6YFmgsNIsRDMImGIpAevGSiC0t+0D8urHYnp0l+KR
-
HT1414 what to pick? ipod or ipad? i am also tempted by the amazon kindle fire hd.
Hey, I am very confused. For a present, my relatives asked me to pick whatver i want, and i really want an apple device of my own. What do i pick? i really dont need a phone, i alredy have a samsung galaxy.
-
A couple of days ago I noticed the right speaker on my Macbook started to make a "swoosh" sound (even with the volume turned completely down). This happens after I have waked up the Macbook from sleep and entered by login password... the "swoosh" noi
-
After Effects CS5 crash on RAM Preview OS X
Hello Friends. I've had a pretty great experience with AE CS5 so far, but I've been getting more and more recurring issues of AE locking up the entire computer on occasional RAM Previews. I get a spinning wheel, and the computer becomes unusable. I c