Update the firmware on my airport express from 7.4.2 to 7.5.2
When I press update the firmware on my airport express from 7.4.2 to 7.5.2 using the airport tool says:
This device and its network service is temporarily unavailable. will you continue?
When I press deliberately and pressed into the code goes started to download the update, but come quickly with this message:
Airport Utility could not find the AirPort wireless device after restarting. You may need to select your network manage network connections and try again.
But my airport lights up green as if it works and I may well be on the net and listen wireless music.
How do I get updated firmware?
Chances are, the update was downloaded and installed successfully.
Try powering down your entire network....every device.....order is not important
Wait a few minutes
Start the modem first and let it run for 2-3 minutes by itself
Start the next device connected to the modem the same way
Continue starting devices one at a time about a minute apart until everything is powered back up
What happens?
Similar Messages
-
How do I update the software on my Airport Express?
Hello everyone,
I have an Airport Extreme base station acting as WDS and an Airport Express station. I recently upgraded the security on the Airport Extreme base station from 128-WEP to WPA (Personal), but I don't know whether I have to do something to the Airport Express base station. It's green light is on. Do I need to do something? Also, how do I update the software in the Express? Whenever I open the Airport Admin Utility, the only thing that comes up on a scan is my Extreme base station. Any advice would be most appreciated.yes you need to update your Airpost Express. I just went through this last week with two of my Airport Expresses. I updated my Base and my Remote's light was green but was unable to view it in Airport Admin Utility. So this is what I ended up doing and it works great.
First bring the Airport Express you are working on in the same room as your computer......just the ease of seeing what is going on with the Airport Express. Next you need to reset it.....take a paper clip and push in the little button next to the Audio port and hold in 10 seconds. Then unplug the unit wait 10 seconds and plug it back in. wait about 3 minutes and then you will need to use Airport Set Up Assistant. You will need to make sure you have WPA Personal on your Airport Express too.
don't forget to make sure you have the update firmware too.
http://www.apple.com/support/airport/
I hope this helps.....
Powerbook G4 1.67 15", 1 gig ram, 128 vram, 80 gig harddrive Mac OS X (10.4.6) Powermac G3 266 mt, Dell 5150,ibook G4, 1 gig shuffle, epson printers, airport -
How do you configure the a network for Airport Express from a PC computer
A friend let me borrow her Airport Express so I could have wireless, but I can't figure out how to set up the network from my PC computer. She just gave me the device without any accompanying instructions or software. The intructions online only explain how to setup the network using an Apple product. How can it be done from a PC?
Use the same instructions and the Windows version of AirPort Utility:
AirPort Utility 5.5.3 for Windows -
Why can't update the firmware for my dr8-a from 120D to 130D?
Good evening MSI!
I tried everything! I tried under dos and under windows white live update. Nothing! In dos (version 6.22 bootdisk) mode display me "Bios Update Fail~~" and Win mode (WINDOWS XP) is freeze. Working the burner after update is failed. Please make working firmware update!!!
Thank you MSI!May be wait for the next version of the update then.
-
Can I choose not to broadcast the name of my AirPort Express?
I would like to know if I can keep the name of my AirPort Express from being broadcast to other computers. On my old Netgear router I could choose to not broadcast the name but, I don't seem to see the option in the AirPort Base Station Utility.
PowerBook G4 12 SuperDrive Mac OS X (10.3.9)A closed network is still broadcasting and still broadcasts the network name.
A casual user won't be able to see the network from their computer.
However anyone with easily obtained software will be able to see it just fine from their computer.
Unfortunately "Closed" networks, MAC access control lists, and reduction in transmission power are all more "feel good" security rather than real security. All these various approaches are dated and mistakenly lead to overconfidence.
WPA is your friend if you value wireless security. -
Updating the firmware of an older airport extreme
I have an early version of the Airport extreme and, probably 1st gen airport express. Is there anyway to update the firmware on these devices so that they have the most recent firmware versions available to those devices. The only identifying info on them is their model numbers.
On the express it is Model# A1084 and on the Extreme it is Model # A 1034. I realize that these are older units and don't expect much from them, just would like to be able to do it.The most recent firmware update for both devices that you mention was 8+ years ago, so you likely already have the most up to date firmware that the devices can handle.
5.7 would be the latest firmware for the AirPort Extreme and 6.3 would be the latest for the Express.
AirPort Extreme Firmware Update 5.7 for Mac OS X - Support - Apple
AirPort Express Firmware Update 6.3 for Mac OS X - Support - Apple -
I have an Ipad and Iphone but I don't have an Airprint at home but only a WIFI printer, my question is if I connect the wifi printer to Airport express, can I print from Ipad and Iphone ? Please help me if anyone knows about this.
Unfortunately, connecting a non-AirPrint-enabled printer to an AirPort base station's USB port will not make it AirPrint-ready.
You will need to use another solution, like Printopia, to be able to print to this printer from an iOS device. -
I updated the firmware to 5.0.1, then began a problem with my gadget I try to restore from a backup firmware, Itunes an error 3194, if I can, and if I do get to shsh ios 5?
Good morning
This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
http://support.apple.com/kb/TS3125
Hope this helps
Cheres -
I bought an Airport Express from a supplier who told me I'd need at least iOS 5.4 on my iPad. My first generation iPad is apparently up to date but the iOS is only 5.1.1. Before I unpack the device I want to know whether it will work with this earlier version.
Apple says that a minimum of iOS 5.0 is required. See the support document below. Look for Requirements on the left hand side of the page about half way down.
Requirements: Compatible with iPhone, iPod touch, and iPad. Requires iOS 5.0 or later.
https://itunes.apple.com/us/app/airport-utility/id427276530?mt=8 -
i have tried to restore my iPad from my computer, but it stops ones it gets to the stage where it is updating the firmware. It will then display " there was an unknown error.....Any suggestion to fix this,?
Temporarily disable antivirus and firewall on computer.
-
How can I administer a Gen1 Airport Express from, my MacPro (OS 10.9, Airport Utility 6.3.2). I can see the Express in the WiFi window but from the Airport Utility I get the following message: " This version of AirPort Utility doesn’t support this base station. Go to AirPort Service and Support for more information." Of course there's nothing of value on the support page. Any clues anyone?
Apple has dropped support in Mavericks (10.9) of the AirPort Express and AirPort Extreme models that were discontinued more than six years ago.
You can still administer the older AirPort models if you have a Mac running Leopard, Snow Leopard, or a PC. -
I need help configuring the Airport express from a PC
Hi there!
I want to configure the airport express from a PC. It runs okay but the connection is open (anyone can browse on my connection)
In a PDF that I found on Apples web site, it says go to
Start-> All programs-> Airport express setup assistant, but there are no programs named Airport on my PC!
Do I have to download a utility for this purpose?
FredrikIf all you want to do is add wireless security to an already configured Express, you'll probably want to use the Airport Admin Utility. You should be able to install it by installing this package:
http://www.apple.com/support/downloads/airport42forwindows.html
If the PC isn't running at least Windows XP, I think you're out of luck. -
I am trying to hook up a airport express from a work server that has a assigned ip address. the airport works but no internet
Encryption wouldn't matter except for Wifi.
While 10.2 might help, there's not much you can do on the Internet these days with less than 10.4.11
Tiger Requirements...
To use Mac OS X 10.4 Tiger, your Macintosh needs:
* A PowerPC G3, G4, or G5 processor
* Built-in FireWire
* At least 256 MB of RAM (I recommend 1GB minimum)
* DVD drive (DVD-ROM), Combo (CD-RW/DVD-ROM) or SuperDrive (DVD-R) for installation
* At least 3 GB of free disk space; 4 GB if you install the XCode 2 Developer Tools (I recommend 20GB minimum)
http://support.apple.com/kb/HT1514
http://www.ebay.com/sch/i.html?_nkw=mac+os+x+tiger+retail+10.4
See Tom's, (Texas Mac Man), great info on where/how to find/get Tiger...
https://discussions.apple.com/message/15305521#15305521
Or Ali Brown's great info on where/how to find/get Tiger...
http://discussions.apple.com/thread.jspa?messageID=10381710#10381710
As far as Memory, that's sort of easy, find your eMac here...
http://eshop.macsales.com/MyOWC/Models.cfm?Family=emac&sType=Memory
As far as Hard Drive, it's not easy to replace the Internal drive, I'd maybe suggest an external Firewire drive to boot from...
http://eshop.macsales.com/item/Other%20World%20Computing/MAU4S7500G16/ -
I have a Lexmark s405 printer and I've just updated the firmware and still can't print wirelessly from my iPad. Why?
That model doesn't appear to support AirPrint (those that do are listed on this page : http://support.apple.com/kb/HT4356)
Have you checked to see if Lexmark have their own app in the store, or there are third-party apps such as Print Central For iPad and Print n Share which might work with it -
HT1218 can I use the 7.3 firmware on my airport express?
can I use the 7.3 firmware on my airport express?
current version 6.3, but de airport express units are not "supported" by airport utility v6. seems that they like me to upgrade firmware?Is it true that AIRPORT UTILITY V6 doesnt support this model?
Yes
However, you can use AirPort Utility 5.6 for Mac OS X Lion to configure the older Express.....and....your newer devices as well, so you might want to make that application your "go to" utility.
Keep both AirPort Utility 5.6 and 6.x on your Mac.
Maybe you are looking for
-
How to populate a Value in popup based on value selected in Parent window
Hi Gurus, I have done a custumization to generate a PDF report for a given DocType and Document ID. I have 2 fields in xxxQuoteDevPG.xml (Parent Window) called DocType and Document Number. Doctype is dropdown list which has 2 values i.e. Sales Quote
-
I have just upgraded Microsoft Office Pro to 2010 from 2007 - I want Acrobat 9 Pro available in all Office programs - Microsoft says - call Adobe - please advise Also I purchased a new tablet pc - can I install my Acrobat 9 Pro on it - I currently ha
-
G-tech G-drive mini 100gb 72 versus LaCie 100gb 7200 RPM Rugged all-terrain
I am deciding between the above two 100GB 7200RPM Bus powered FireWire drives for video (HDV/DVCPRO) editing. While G-tech seems to have a better rep on this board, the LaCie has a FW800 connection, while the G-tech only has the FW400 connection. Is
-
Webinar- Connect Third Party Systems with SAP B1 – DI API, DI Server, B1WS
Webinar happened on 21st August. Get the Presentation, Video recording and answers of all the questions asked in the webinar through the below link. Webinar- Connect Third Party Systems with SAP B1 - DI API, DI Server, B1WS
-
Error when executing statement for table/stored proc DB2 - Data Truncation
Hi, I have one call sp in XI with n parameters int and two parameters out. well, to implement the interface gives the following error com.sap.aii.af.ra.ms.api.DeliveryException: Error processing request in sax parser: Error when executing statem