Updated to iOS 8 yesterday, sound not working anymore

i updated my iPAD to iOS 8 yesterday and now no form of sound works. volume conditions all perfect

(A) Try reset iPad
Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears
Note: Data will not be affected.
(B) Try reset all settings
Settings>General>Reset>Reset All Settings
Note: Data will not be affected but settings for Wi-Fi, FaceTime, Message, Home Sharing will be reset

Similar Messages

  • Mac os 10.4.10 software update problem -- my mac does not work anymore :(

    hello!
    i have a powerbook G4- PPC. just today, i did a software update of my OS to 10.4.10 (it was the available update version according to the automatic uptae) and during the final stage of the installation, it says "a problem was encountered...installation package is moved to trash"
    when i browsed my mac, my apps does not work anymore!!! they just bounce from the dock when i clicked it but it won't open any window. i emptied the trash and restarted my mac but sadly, it just boot but won't continue to the log in part, only in the silver window with the apple logo and mac os x tiger... and the mouse just turns into the color wheel. i waited for 30 mins and nothing happened.
    i don't have a startup disc because the mac is a gift and it was long time ago. is ther a software i can use to fix or revert the changes of the unsuccessful OS update? why is there always a problem when i do OS update? isn't apple software stable?
    My mac problems' driving me crazy!!!

    There are no guarantees, but following this procedure when installing updates and upgrades on your Mac will go a long way towards avoiding unpleasant after effects and ‘post-update stress disorder’.
    It is also worth noting that it is an extreme rarity for updates to cause upsets to your system, but they may well reveal pre-existing ones, particularly those of which you may have been unaware. If you are actually aware of any glitches, make sure they are fixed before proceeding further.
    So before you do anything else:
    If you can, make a full backup first.
    Turn off sleep mode for both screen and hard disk.
    1. Repair Permissions (in Disk Utility)
    2. Verify the state of your hard disk using Disk Utility. If any faults are reported, restart from your install disk (holding down the C key), go to Disk Utility, and repair your startup disk. Restart again to get back to your startup disk.
    At least you can now be reasonably certain that your system does not contain any obvious faults that might cause an update/upgrade to fail.
    3. Download the correct version of the COMBO update from the Apple download site. If your car runs on gasoline you would not want to fill the tank with diesel, so don’t try to install the PPC updater on an Intel Mac!
    If you prefer to download updates via Software Update in the Apple menu (which would ensure that the correct version for your Mac was being downloaded), it is not recommended to allow SU to install major (or even minor) updates automatically. Set Software Update to just download the updater without immediately installing it. There is always the possibility that the combined download and install (which can be a lengthy process) might be interrupted by a power outage or your cat walking across the keyboard, and an interrupted install will almost certainly cause havoc. Once it is downloaded, you can install at a time that suits you. You should make a backup copy of the updater on a CD in case you ever need a reinstall.
    Using the Combo updater ensures that all system files changed since the original 10.4.0 are included, and any that may have been missed out or subsequently damaged will be repaired. The Delta updater, although a temptingly smaller download, only takes you from the previous version to the new one, i.e. for example from 10.4.9 to 10.4.10. Software Update will generally download the Delta updater only. The preferable Combo updater needs to be downloaded from Apple's download site.
    Now proceed as follows:
    4. Close all applications.
    5. Unplug all peripherals except your keyboard and mouse.
    6. Install the update/upgrade. Do not under any circumstances interrupt this procedure. Do not do anything else on your computer while it is installing. Be patient.
    7. When it ask for a restart to complete the installation, click restart. This can take longer than normal, there are probably thousands of files to overwrite and place in the correct location. Do nothing while this is going on.
    8. Once your Mac is awake, repair permissions again, and you should be good to go!
    If your Mac seems slightly sluggish or ‘different’, perform a second restart. It can’t hurt and is sometimes efficacious!
    9. Open a few of your most used applications and check that all is OK. In this connection please remember that not all manufacturers of third party applications and plug-ins, add-ons, haxies etc, will have had time to do any necessary rewrites to their software to make them 10.4.10. compliant. Give them a weeks or two while you regularly check their websites for updates. This applies particularly to plug-ins for Safari 3.
    N.B. Do not attempt to install two different updates at the same time as each may have different routines and requirements. Follow the above recommendations for each update in turn.
    Lastly, Apple's own article on the subject of Software Update may also be useful reading:
    http://docs.info.apple.com/article.html?artnum=106695

  • Migrating V9 to V10: Update XML Fragment CLOB does not work anymore

    I have an XML Schema that contains an element, named Operazione, mapped to a CLOB.
    I just migrate to Oracle 10.1.0.2.0 from version 9.2.0.2.0 and the code I developed does not work anymore.
    To get a CLOB on v 9.2.0.2.0 I issued the following statement:
    select extractValue(value(p),'/operazione.log/Operazione') from XMT_OPERAZIONE_LOG p
    where existsNode(value(p),'/operazione.log/Journal[NumeroElettronico=1234567890]') = 1
    To make it working on V10 I have to change it as follow:
    select extract(value(p),'/operazione.log/Operazione').getClobVal() from XMT_OPERAZIONE_LOG p
    where existsNode(value(p),'/operazione.log/Journal[NumeroElettronico=1234567890]') = 1
    So using extract intead of extractValue and adding getClobVal() I was able to read the CLOB.
    The problem that I was not able to solve is related to CLOB update. In V9 just adding the “for update” clause I was able to change the CLOB value on DB.
    In V10 if I run the V9 statement I get the error:
    ORA-03113: end-of-file on communication channel
    If I use the statement modified for V10, adding the “for update” clause, I get the CLOB and I can change the CLOB value but nothing goes on the DB. Probably I am working on a copy of the DB CLOB.
    If I remove the getClobVal() I get an OPAQUE type that I can use on a XMLType but, still, nothing is stored on DB.
    Any suggestion ?
    I tried with both OCI and Thin Client

    Can anybody help me ?
    Is it better to use different strategies ( eg. Stored Procedure, DBMS_XMLSTORE etc, etc. ) ?
    Any experience updatating XML Fragment CLOB on Oracle V10 ?

  • Why does my sound not work anymore?

    Hi all,
    The problem im having with my iPhone is that im not able to listen music anymore. My phone does play sounds, but only when docked or having my earphones plugged in.
    It does NOT work without earphones and the volume slider does not show up when playing music.
    However, it DOES make sounds when my alarm goes off or when im getting called, ringtones work fine too.
    Anyone knows what could be the issue?
    Thanks

    I had the same issue, after I made 2 changes in the iPad settings! (1) Side switch changed from mute to lock rotation! and (2) the auto lock changed from never to 10 minutes!. I changed these settings back to previous and cured the problem instantly, I then changed the auto lock time and have so far 2 weeks later had no issues. This seems to indicate a problem with the allocation program for the side button!

  • Since last software update, pre-paid internet does not work anymore. Get "you have not signed up for a data plan" message. Pre-paid acct is in order! What's up???

    I have had  an iPad 3G for more than a year now. I did not get it with a SIM card, since I expected to use almost completely at home, where we have wireless internet. Eventually, I decided  it would be handy to be able to take it on the road, and signed up for pre-paid Internet with KPN (national Dutch telecommunications company). That worked fine, until the last big iPad software update. Since then, whenever I try to make a connection outside the house, I get the following message…
    Mobile Data Account
    You have not signed up for a data plan.
    Would you like to set up a new account?
    If you don’t, you can do it later in Settings.
    …with the options of ‘Later’ or ‘Now’ to press. If I press Now, I get a screen “Please wait while the page is loading – this should only take a few seconds to complete.” But it never does, the ball just keeps spinning and spinning and spinning….
    To my mind, with pre-paid internet I should not HAVE to set up a Mobile Data Account in the first place. I’ve checked with KPN, and my account is completely in order. I’ve checked with the local Apple store, and the geniuses say they’ve never seen this. Can anyone help me?

    I updated to 3.6.4 and when I went to NetFlix to watch the next show of a series, it said
    something like
    Installation complete, restart your browser.
    I restarted browser, same problem. Restarted comp. Same problem.
    I updated Adobe Flash 10.1, still same problem.
    But able to watch some vids on other sites, but full screen gave me the big blank white screen with audio only, had to click around in the dark ( so to speak) to find the minimize button.
    I did a System Restore to before the Firefox and Adobe updates.
    I then did not update Firefox as recommended and went to NetFlix and wellah, i can view the movies again.
    And Full Screen is fine.
    I then experimented and updated Firefox only, went to NetFlix and got same msg with no viewable shows.
    So did a System Restore once more.
    Staying at 3.6.3 for a while longer until I know I can watch my movies.
    I don't own a TV, so this is my only form of an occasional escape.
    I do hope this is figured out soon.
    With what I have done, it seems to be Firefox, Not Flash.
    Good Luck to us all.

  • IChat chat sounds not working anymore

    About a week ago, the sounds for iChat stopped sounding. This includes when I log-in, receive and send messages, etc. I check preferences, and all of those are enabled. I do have Chax installed, but it was still working for a while. Any suggestions?

    Hi HalfHazzard,
    The Alerts that you have set either globally in the iChat preferences or indvidually in the Buddy list are stored in one of the iChat .plists so it may be a good time to delete this .plist and possibly reset them.
    The one in question is com.apple.ichat.plist
    It is found in /users/(your account)/Library/Preferences
    Delete with iChat active and then restart iChat.
    If it does not work this way then delete it with iChat shut down.
    10:39 PM Tuesday; April 25, 2006

  • After update Gedit and Epiphany plugins not working anymore

    Gedit and Epiphany plugins stopped working after recent update. They are listed in plugin dialog, but can't be enabled. Does anybody know how to solve this problem?

    I was able to successfully enable the plugins by re-compiling gedit using the ABS system.
    However, I do think this is a bug, and that we should report it.  I'm unfamiliar with that
    process as well.  If anyone can post a quick suggestion as to the best place to file a bug report,
    I would appreciate it :-)
    In the meantime, here's what I did.  This was my first time using the ABS system, so
    I went to http://wiki.archlinux.org/index.php/ABS All the below instructions are on the wiki,
    these instructions are specific to gedit:
    I installed abs using pacman.
    # pacman -Sy abs
    I edited /etc/abs.conf, and put a ! in front of the testing REPOS:
    REPOS=(core extra community !testing)
    As root, I ran
    # abs
    A bunch of stuff was downloaded to my /var/abs folder.
    I make a directory in my home folder for gedit's stuff:
    $ mkdir -p /home/yourusername/abs
    I copied gedit's stuff from /var/abs to my abs folder:
    $ cp -r /var/abs/extra/gedit/ ~/abs
      $ cd ~/abs/gedit
    I ran makepkg -s
    $ makepkg -s
    A bunch of stuff downloaded and compiled.  When it was done, there was a new gedit-2.24.3-1-i686.pkg.tar.gz file in the same directory.
    I told pacman to install the tar.gz file.  Note that I did not have to uninstall gedit.
    As root:
    # pacman -U gedit-2.24.3-1-i686.pkg.tar.gz
    And that was it!  I could then go into gedit and enable/disable whatever plugins I wanted.
    Hope this helps,

  • Fading of sound not working anymore

    Hi All,
    I've been working on this big project for a while now and I'm in the proces of adding music to the video. All of a sudden the added music clips don't fade out anymore, they just break off. Nothing I've tried seems to work including re-adding, Converting the music to aif, Restarting the copmuter & trashing the plist file. Has anybody had this porblem before, and if so is there a quick solution?
    Thanks

    I've transferred the project to FCP and edited it there.

  • Error updating CC on Mac, apps not working anymore

    Hi, I'm getting an error 595629d0-4f3e-4383-8ec4-ae90204c08de when I update CC. CC askes me to login again whem I want to update and it's sending this error back. I also can't open any CC apps.
    Thank you!

    Hi Jeff, I'm using OS X Mavericks 10.9.1
    In the first attachement you can see the Creative Cloud screen that always stays blank.
    In the second attachement you can see an error screen (more a pop up) that show an errro after I tried to login with my Adobe ID. I have to do that when I start up any of the Adobe apps (Photoshop, Premier, Acrobat etc).
    Thanks in advance!
    Regards,
    iToony

  • Enter key does not work anymore in address bar after FF update

    After the update the Enter key does not work anymore. Neither when I type the url directly, nor when I select it from the history.
    In short FF has become unusable. Now I need to install and use a less crappy browser. Extremely sloppy, amateuristic update.

    see if this is helpful : go to Tool > Options > Advanced > General tab > Browsing and '''Uncheck''': "Use hardware acceleration when available" .

  • Since update my IPAD 4 Wi-Fi   Cellular (MM) A1460 to iOS 7.0.3 is not working anymore

    Hello!
    My iPAD 4 with WI-FI and Cellular (MM) model number A1460 (iPAD 3,6) after an update to iOS 7.0.3 from iTunes is not working anymore.
    I tryed for 3 times than I put him in recovery mode and hw gave me this error:
    [11:24:27.0127] Restore completed, status:1
    [11:24:27.0127] Failure Description:
    [11:24:27.0127] Depth:0 Error:AMRestorePerformRestoreModeRestoreWithError failed with error: 1
    [11:24:27.0127]    Depth:1 Error:The operation couldn’t be completed. (AMRestoreErrorDomain error 1 - Failed to handle baseband update status message)
    I can't get him out of recovery mode
    If someone cand help me, I'll give him a big gift.
    If you need I have the log from updater.
    Thank you in advance and I'll wait for an answer.
    Cheers!

    Hey rmacbeth, I'm sorry to hear about your iPad troubles. It seems like with every major iOS release, these issues come up on older models (the iPad 3 is relatively new though...weird)
    Anyways, it sounds like you've tried everything already and nothing seems to be working. If you're sure that it's a software issue with iOS and has nothing to do with your physical home button, I'd recommend restoring your iPad to factory settings by doing the following:
    1. Make a backup of your iPad (just connect it and select the backup option in iTunes)
    2. Next, select factory restore. It'll ask you to back up your iPad here if you haven't already.
    3. Try quickly setting it up as a new iPad.
    4. Try to duplicate the issue with the freezing, just use it for a day and see if it happens at all
    5. If everything seeems to be working, restore again except this time, do it from the backup you made earlier
    6. Try again to see if the issue comes up by using it normally in a day
    7. If it does happen again, take it in to the Apple store to get it looked at as there may be some underlying software issue that a factory restore can't resolve
    Again, sorry about your iPad, I hope you can resolve your issues quickly!

  • My iPhone crashing after latest IOS Update. Screen is not working anymore. I cannot use buttons, the screen is freezing up.Only thing I am able, is to 'restart' the phone. Now it does it after 5 minutes itself! Already removed en reset phone, no success!

    My iPhone crashing after latest IOS Update. Screen is not working anymore. I cannot use buttons, the screen is freezing up.Only thing I am able, is to 'restart' the phone. Now it does it after 5 minutes itself! Already removed en reset phone, no success!
    Can anyone help me?

    Hi there Cinthia88,
    I would recommend taking a look at the troubleshooting steps found in the article below.
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/ts3281
    -Griff W.

  • Just updated my iPad with iOS 7 and now internet does not work anymore, how to fix if???? Desperate

    Just updated my iPad with iOS 7 and now internet does not work anymore, how to fix if???? Desperate

    Try resetting your iPad:
    Double click the Home button. Slide up with one finger on ALL your apps to close them.
    Then, Press the Sleep/Wake button + Home button and hold 15 seconds or until you see the Apple logo.
    This will reset your device without erasing data, apps or settings.

  • I am using iPhone 4S lock came from Japan. From beginning, it is IOS 5.1.1 but now i have updated to IOS 7 and it is not working anymore now. Can you tell me what i have to do now?

    I am using iPhone 4S lock came from Japan. From beginning, it is IOS 5.1.1 but now i have updated to IOS 7 and it is not working anymore now. Can you tell me what i have to do now?

    No Japanese carrier provides unlocking services. Therefore, your phone must have been hacked to unlock it. That hack was removed when you updated the software. You need to be a legitimately unlocked phone.
    Best of luck.

  • So I have updated my iphone4 GSM to ios 6.01, however after updating, my safari and mail could not work anymore, when i open these 2 apps, it just opens and hangs then it crashes.

    So I have updated my iphone4 GSM to ios 6.01, however after updating, my safari and mail could not work anymore, when i open these 2 apps, it just opens and hangs then it crashes.
    anybody can help me ?

    So I have updated my iphone4 GSM to ios 6.01, however after updating, my safari and mail could not work anymore, when i open these 2 apps, it just opens and hangs then it crashes.
    anybody can help me ?

Maybe you are looking for