Updated to windows 10 and now my computer stays black when it goes into sleep mode
I just updated my computer to windows 10. Whenever it goes into sleep mode and i try to move the mouse it just stays black and i have to turn my computer off and then on again. after that it finally works but its just annoying. I already tried updating my card driver, but it said it was already up to date.
My iMac i7 quad was having the same symptoms with the blue screen and long startup times a couple of months ago. Apple Care told me to bring it in to the local Apple Store, and after some diagnostics, the hard drive required replacing. It took one day to replace the hard drive and my iMac is running great. I only had the iMac for about 12 months when the drive needed to be replaced. Not sure if that is your Mac's problem, but it was for mine.
Similar Messages
-
W510 does not wake up when it goes into Sleep mode - Windows 7 Bit
Hi All,
The Lenovo thinkpad w510 does not want to wake up once it goes into sleep mode, I have to push the power button until it shuts down completely and then reboot it completely, I have tried different settings in the power management etc. We have the same pissue on 3 different w510`s with Windows 7 pro 64 Bit
Has anybody got a solution for this problem?
Regards,
Solved!
Go to Solution.Hi russellwth,
Welcome To Lenovo Forums.
This issue has been solved with the latest BIOS for the W510.
Please check our Knowledge Base Article regarding this issue.
//JameZ
Check out the Community Knowledge Base for hints and tips.
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"!
X240 | 8GB RAM | 512GB Samsung SSD -
For the past few days now whenever I go to turn on my iMac it takes roughly ten or more minutes to boot up. For the portion of this time it sits on a blank blue screen. At first it comes up to a plain white screen which after about 30 seconds has the apple logo on it and the spinning circle for about a minute then to the blue screen, every time. Then, to top it off right when this started happening another problem began occurring. The computer is set to go into sleep mode after 15 minutes of no use. But, if it is in sleep mode for too long I am unable to get it out and I have to restart the entire computer, but if it is just for a few seconds into sleep or a minute I am able to get the screen to come back. I can still here the fan running and such so I don't know what is going on. I have searched through discussion after discussion. I have tried: repairing disks, repairing permissions, starting up in safe mode, and such. There has been no luck so far. I was wondering if anyone could offer insight into fixing at least one of these problems since my schooling relies on the computer.
By the way I this is an iMac 10.6.4 refurbished which we just bought about two weeks ago.
Thanks for any suggestions!My iMac i7 quad was having the same symptoms with the blue screen and long startup times a couple of months ago. Apple Care told me to bring it in to the local Apple Store, and after some diagnostics, the hard drive required replacing. It took one day to replace the hard drive and my iMac is running great. I only had the iMac for about 12 months when the drive needed to be replaced. Not sure if that is your Mac's problem, but it was for mine.
-
I installed the latest update of iTunes and now my computer is extremely slow and it freezes. When I click on the itunes icon, nothing happens, if it opens is a long time afterwards. Most of the time it does not even open, but the computer is very slow. It is a PC desktop running windos xp.
Hey ArgentoSB!
I have an article for you that can help you troubleshoot these issues:
iTunes for Windows XP: Troubleshooting unexpected quits, freezes, or launch issues
http://support.apple.com/kb/ts1421
Take care, and thanks for visiting the Apple Support Communities.
-Braden -
I installed Yosemite and now my computer is slow when logging in. Also when I type my password, a bar appears measuring the process and then all of a sudden the screen images are distorted. After that my home screen appears and everything seems normal. What can I do to fix this?
Here is what the etrecheck results are:
Problem description:
slow at start up, screen is distorted while logging in, it is fine after
EtreCheck version: 2.1.8 (121)
Report generated April 5, 2015 at 9:42:01 AM PDT
Download EtreCheck from http://etresoft.com/etrecheck
Click the [Click for support] links for help with non-Apple products.
Click the [Click for details] links for more information about that line.
Hardware Information: ℹ️
MacBook Pro (13-inch, Early 2011) (Technical Specifications)
MacBook Pro - model: MacBookPro8,1
1 2.3 GHz Intel Core i5 CPU: 2-core
4 GB RAM Upgradeable
BANK 0/DIMM0
2 GB DDR3 1333 MHz ok
BANK 1/DIMM0
2 GB DDR3 1333 MHz ok
Bluetooth: Old - Handoff/Airdrop2 not supported
Wireless: en1: 802.11 a/b/g/n
Battery Health: Normal - Cycle count 297
Video Information: ℹ️
Intel HD Graphics 3000 - VRAM: 384 MB
Color LCD 1280 x 800
System Software: ℹ️
OS X 10.10.2 (14C109) - Time since boot: 0:7:0
Disk Information: ℹ️
Hitachi HTS545032B9A302 disk0 : (320.07 GB)
EFI (disk0s1) <not mounted> : 210 MB
Recovery HD (disk0s3) <not mounted> [Recovery]: 650 MB
Macintosh HD (disk1) / : 318.84 GB (174.85 GB free)
Encrypted AES-XTS Unlocked
Core Storage: disk0s2 319.21 GB Online
MATSHITADVD-R UJ-898
USB Information: ℹ️
Apple Inc. Apple Internal Keyboard / Trackpad
Apple Inc. BRCM2070 Hub
Apple Inc. Bluetooth USB Host Controller
Apple Inc. FaceTime HD Camera (Built-in)
Apple Computer, Inc. IR Receiver
Thunderbolt Information: ℹ️
Apple Inc. thunderbolt_bus
Gatekeeper: ℹ️
Mac App Store and identified developers
Kernel Extensions: ℹ️
/System/Library/Extensions
[not loaded] com.devguru.driver.SamsungComposite (1.1.0) [Click for support]
[not loaded] com.logmein.driver.LogMeInSoundDriver (1.0.3 - SDK 10.5) [Click for support]
/System/Library/Extensions/ssuddrv.kext/Contents/PlugIns
[not loaded] com.devguru.driver.SamsungACMControl (1.1.0) [Click for support]
[not loaded] com.devguru.driver.SamsungACMData (1.1.0) [Click for support]
Startup Items: ℹ️
HP Trap Monitor: Path: /Library/StartupItems/HP Trap Monitor
Startup items are obsolete in OS X Yosemite
Problem System Launch Daemons: ℹ️
[failed] com.apple.ucupdate.plist
[failed] com.apple.watchdogd.plist [Click for details]
Launch Agents: ℹ️
[not loaded] com.google.keystone.agent.plist [Click for support]
[not loaded] com.hp.help.tocgenerator.plist [Click for support]
[not loaded] com.logmein.LMILaunchAgentFixer.plist [Click for support]
[not loaded] com.logmein.logmeingui.plist [Click for support]
[not loaded] com.logmein.logmeinguiagent.plist [Click for support]
[not loaded] com.logmein.logmeinguiagentatlogin.plist [Click for support]
Launch Daemons: ℹ️
[not loaded] com.adobe.fpsaud.plist [Click for support]
[not loaded] com.google.keystone.daemon.plist [Click for support]
[not loaded] com.logmein.logmeinblanker.plist [Click for support]
[not loaded] com.logmein.logmeinserver.plist [Click for support]
[not loaded] com.logmein.raupdate.plist [Click for support]
[not loaded] com.microsoft.office.licensing.helper.plist [Click for support]
User Launch Agents: ℹ️
[not loaded] com.adobe.ARM.[...].plist [Click for support]
[not loaded] com.facebook.videochat.[redacted].plist [Click for support]
[not loaded] com.google.GoogleContactSyncAgent.plist [Click for support]
User Login Items: ℹ️
iTunesHelper UNKNOWN Hidden (missing value)
AdobeResourceSynchronizer Application Hidden (/Applications/Adobe Reader.app/Contents/Support/AdobeResourceSynchronizer.app)
Android File Transfer Agent Application (/Users/[redacted]/Library/Application Support/Google/Android File Transfer/Android File Transfer Agent.app)
HP Product Research Application (/Library/Application Support/Hewlett-Packard/Customer Participation/HP Product Research.app)
HPEventHandler Application (/Library/Printers/hp/hpio/HPEventHandler.app)
Internet Plug-ins: ℹ️
o1dbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
LogMeInSafari64: Version: 1.0.660 [Click for support]
Default Browser: Version: 600 - SDK 10.10
Silverlight: Version: 5.1.10411.0 - SDK 10.6 [Click for support]
FlashPlayer-10.6: Version: 17.0.0.134 - SDK 10.6 [Click for support]
LogMeIn: Version: 1.0.660 [Click for support]
Flash Player: Version: 17.0.0.134 - SDK 10.6 [Click for support]
LogMeInSafari32: Version: 1.0.660 [Click for support]
QuickTime Plugin: Version: 7.7.3
googletalkbrowserplugin: Version: 5.40.2.0 - SDK 10.8 [Click for support]
AdobePDFViewer: Version: 10.0.1 [Click for support]
SharePointBrowserPlugin: Version: 14.1.0 [Click for support]
iPhotoPhotocast: Version: 7.0 - SDK 10.7
3rd Party Preference Panes: ℹ️
Flash Player [Click for support]
Time Machine: ℹ️
Time Machine not configured!
Top Processes by CPU: ℹ️
7% ocspd
4% WindowServer
1% kextd
0% ps
0% securityd
Top Processes by Memory: ℹ️
137 MB Microsoft Word
120 MB Safari
86 MB ocspd
82 MB CalendarAgent
77 MB WindowServer
Virtual Memory Information: ℹ️
310 MB Free RAM
1.89 GB Active RAM
1.55 GB Inactive RAM
544 MB Wired RAM
1.13 GB Page-ins
8 KB Page-outs
Diagnostics Information: ℹ️
Apr 5, 2015, 09:32:47 AM Self test - passed
Apr 5, 2015, 09:30:05 AM /Users/[redacted]/Library/Logs/DiagnosticReports/AdobeResourceSynchronizer_2015 -04-05-093005_[redacted].crash
Apr 4, 2015, 01:12:41 PM /Users/[redacted]/Library/Logs/DiagnosticReports/AdobeResourceSynchronizer_2015 -04-04-131241_[redacted].crash
Apr 4, 2015, 08:13:57 AM /Users/[redacted]/Library/Logs/DiagnosticReports/AdobeResourceSynchronizer_2015 -04-04-081357_[redacted].crashReinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Reinstalling OS X Without Erasing the Drive
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility and press the Continue button. After Disk Utility loads select the Macintosh HD entry from the the left side list. Click on the First Aid tab, then click on the Repair Disk button. If Disk Utility reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit Disk Utility and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Alternatively, see:
Reinstall OS X Without Erasing the Drive
Choose the version you have installed now:
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless. -
Ever since I got the new update 5.1 my iPod's been dying faster, even after I charge it. It used to last for at least 3 hours, now it won't even last one hour and dies for no reason (even when it's in sleep mode, and not in use) What's wrong with it? Is it the update? It's lagging as well..
Some Users have Reported that a Restore as New has helped Resolve issues...
Backup and Set Up as New Device
http://support.apple.com/kb/HT4137 -
I just updated my ipad and now I can't get my kindle books in landscape mode. I have th elock roatation off everythign else goes to landscape
iPhone, iPad or iPod screen will not rotate, fix
http://appletoolbox.com/2013/03/iphone-ipad-or-ipod-screen-will-not-rotate-fix/
iOS Screen Does Not Rotate
http://support.apple.com/kb/ts3805
Cheers, Tom -
My macbook boots up and only stays on for 30sec and goes into sleep mode
My macbook boots up and only stays on for 30sec and goes into sleep mode! Any suggestions as to why this might be happening? Thanks....
I assume you have checked your sleep settings in System Preferences>Energy saver
I also assume this has just happened recently and spontaneously, not after installing any particular hardware or software or you would probably have mentioned it...if anything new has been added recently, obviously just remove it!
It could be the battery - have your tried it just on mains? If it's a pre unibody MacBook try it without the battery at all. This could happen if you have a non-Apple (cheap Chinese) replacement battery.
Try NVRAM, PRAM & SMC resets (Google if you don't know how)
Try booting from the install media and repairing or reinstalling OS X. (Back up first!)
Just out of interest if you boot from a DVD or go into Open Firmware or Boot Select modes, does it still sleep after 30 seconds or is it just in OS X? -
My Imac goes into sleep mode but won't come out. The keyboard/mouse won't rouse it and the power button won't do it either. I have to unplug the computer, re-plug it in and then hit the power button. Help?
I looked around the internet and found an old post that seems to have solved the problem. I had a relatively new USB port (powered) that I unplugged and, ta da, the problem disappeared. I'm not sure why this happens (I'm not a tech person) but it seems like this should have been worked out in testing somewhere.
-
Apple tv loses home sharing when my computer goes into sleep mode
Just recently, my Apple TV says that home sharing is off when my computer goes into sleep mode. It never used to do that - any suggestions?
I have the same problem here. Always back-ed up with Time Machine (OSX 10.9 Mavericks) to Western Digital drives. MyBooks, MyPassport 1TB (USB 3.0), all works fine. Time Machine is actually doing back-ups overnight. Since I got this new 2TB MyPassport Ultra USB 3.0 it's working perfect during days, but every morning when I wake up the MacBook from sleep, I get this annoying error:
Time Machine couldn’t complete the backup to “MyPassportUltra”.
Unable to complete backup. An error occurred while creating the backup folder.
Latest successful backup: Today, 02:27 am
I'm also not able to write anything to that drive, or unmount it. It stil shows up in Finder, and I'm able to read all the data perfectly fine. When I do a Disk Utility Verify Disk directly after, I get this:
Checking volume
disk3s2: Scan for Volume Headers
Invalid Volume Header @ 0: I/O error
Invalid Volume Header @ 2000021315072: I/O error
disk3s2 is not a CoreStorage volume
Error: This disk needs to be repaired. Click Repair Disk.
I don't click Repair Disk, as this will probably screw up my partition. Instead, I have to unplug the USB cable (which is bad for the drive, there's no time to park the drive's heads) and plug it in again. After clicking Backup Now, Time Machine immediately starts backing up, and the drive works fine the rest of the day.
I contacted WD Support, and they are sending me a booster USB cable. As System Information reports, the drive receives enough power though:
Current Available (mA): 900
Current Required (mA): 224
Unfortunately there's no firmware update for this drive, which will probably fix this. See this topic: https://discussions.apple.com/thread/4196704. -
Monitor goes into sleep mode and will not wake up
My monitor goes to sleep and will not wake up. I try powering off and that will not respond. I have to unplug the workstation and start back up. I have turn off sleep to never sleep and now it just goes to sleep when Im working.
Hello @rosendahl14,
Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More.
I have read your post on how your monitor goes into sleep mode and will not wake up, and I would be happy to assist you in this matter!
To rule out any sleep mode issues with the monitor, I am providing you with some steps you can try below:
Step 1. Unplug the power cord from the back of the monitor and the wall
Step 2. Hold the power button down for at least one minute
Step 3. Plug the power cord back into the monitor and then into the wall outlet (not a power bar or surge protector)
Step 4. Press the Menu button on the monitor
Step 5. Navigate to the Factory Reset option and select it
Step 6. Try a different cable connecting your monitor to your computer
If the above steps did not resolve your issue you can try the monitor on a computer or other device to see if the issue persists. Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region.
http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html
To further diagnose a possible hibernation issue with your desktop, I recommend following the steps in this document on Troubleshooting sleep and hibernate issues (Windows 7). I also recommend following the steps below to reset your system's power management settings:
Step 1. Click the Start button
Step 2. In the search box, type "Command Prompt"
Step 3. Right-click Command Prompt
Step 4. Click Run as administrator
Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter
reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone
Please re-post with the results of your troubleshooting, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping! -
I am Streaming audio from my IPAD to my Apple TV from Rhapsody application. when Apple TV go into Screen Saver mode, about 5 minutes after that it stops playing the Audio Stream and goes into Sleep mode. I am using the Optical Out from the Apple TV to my receiver, the Apple TV is hard Wired to the Network, the IPAD is Wirelessly attached to the network (it continues to play the Audio Stream). When the Apple TV is turned back on it resumes playing once I manual select it for output from the IPAD. All device are on current releases of software. I have no Video hooked up to the Apple TV. How do I correct this?
Intermittent problems are often a result of interference. Interference can be caused by other networks in the neighbourhood or from household electrical items.
You can download and install iStumbler (NetStumbler for windows users) to help you see which channels are used by neighbouring networks so that you can avoid them, but iStumbler will not see household items.
Refer to your router manual for instructions on changing your wifi channel or adjusting your multicast rate.
There are other types of problems that can affect networks, but this is by far the most common, hence worth mentioning first. Networks that have inherent issues can be seen to work differently with different versions of the same software. You might also try moving the Apple TV away from other electrical equipment. -
24" imac goes into sleep mode and lights on circuit flicker
Hi -
I have a 24" imac and have found that when the display goes into sleep mode the lights on the circuit flicker.
I have searched the web and other users have complained of the same issue with no resolution.
Here is a similiar post - https://discussions.apple.com/thread/2606099?start=0&tstart=0. The resolution is probably you need to get the iMac serviced, what i'm wondering is what is the problem in the imac that is causing the issue. Is this a defect?
Before anyone questions the circuitry in my house here is what I have verified.
An electrician has come and verified the electric panel is good and all circuit breakers are good. All circuits in my house are copper, no aluminum.
I can plug the iMac into any circuit and the problem starts right when the Imac's display goes to sleep. I have owned the iMac for approximately 5 months now (bought it used) and the problem started about a month ago.
Assuming this has to be serviced I dread to wonder the price .
Thanks for anyones help.The sleep timeout has nothing to do with disk activity. It's based on user input, although some background processes can pre-empt it. If you don't want the machine to sleep automatically, disable automatic sleep in the Energy Saver preference pane.
-
RBDAPP01 going into SLEEP Mode and Idocs still in 64 status
Hey all,
I have a Inbound Idoc interface which is being processed using RBDAPP01 Program. The Issue I am facing is that the job running the rbdapp01 program goes into sleep mode even though there are idocs present in 64 status. I tried to debug the work process using SM66 but it does not open any debugging window although it says debugging started. If I cancel the Job and run it again it processes those Idocs Any input on how one can resolve this issue?
Thanks.Hi Aparna,
Here is extract from SAP material on running RBDAPP01 transaction and possible reasons for delay in processing. HOpe this can help you.
To automate the treatment of IDocs, you must run the ABAP program RBDAPP01 (transaction BD20) in job. This program has a very good option for parallel processing which can reduce a lot the time required for treatment. However use it carefully and make sure you set a packetsize high enough to avoid that your SAP system be overwhelm by demands for available dialog tasks (don't forget one dialog task is monopolized per IDocs packed to treat).
Best Regards,
Krishna -
Since yesterday I am facing problem,when it goes in sleep mode it actually turn off and does not come up after pressing start button but every time I have to hard reset it to turn it on .It is 4 gen running on 4.3.3.Please help
so I have called HP tech support 12 times over the last 6 weeks and still my HP Officejet 4620 loses connection overnight. Of course becasue it was a birthday present I spent more time than I normally would have on this issue. While the tech are very polite they have not fixed my problem and now it is too late to return printer to store. This is a lot of money wasted and I think they need to admit this is a bug in this printer and resolve the problem!!!!!
Maybe you are looking for
-
VGA to S-video or composite video adapter
I need some way to get the video output of my computer to my T.V. The computer has no S-video or anything other outputs for video besides the VGA one. And I don't have a T.V. with VGA input. Has anyone ever seen an adapter for something like this? I
-
HI Gurus Please tell me the T code for report which will list the IOs and corresponding PR s Thanks Avadhut
-
"No Access" privelage on external drive?
I purchased a SMARTDISK 250gig USB2 drive for my iMac G4 and MacBook Pro. Unfortunately, playing around with permissions for the drive (via Get Info), I set all to "No Acceess" and logged out. When logging back in, the drive does not appear. Firing u
-
Muse/Acrobat question about interactive PDFs linked to in Muse...
So I made a link to email, gave it a blue rollover state, exported this in an interactive PDF which I then have a link to in Muse. When you click on it, it opens in a new window/tab, w/ this weird gray color behind it. Any ideas how I can remove this
-
Hi, While setting autotrace i get the below error, SQL> grant all on plan_table to user; Grant succeeded SQL> grant plustrace to user; Grant succeeded connecting through the user i get this error SQL> set autotrace on; SP2-0613: Unable to verify PLAN