Updating firmware in Airport Express disables connection to Internet

After updating my Airport Express to firmware 7.6.1 it will no longer connect to the internet via a 4-port router that is connected to a DSL modem. This arrangement was working immediately prior to the firmware upgrade. I have unplugged/plugged in the AE, turned off then on the modem/router/AE combo all to no avail.
The AE establishes a LAN, but Airport Utility indicates that the AE beleives that the Internet is disconnected, when in fact all the other devices attached to the router via ethernet cableing works as expected.
Any suggestions for reestablishing a working internet connection via the AE would be appreciated. Thanks.

I was able to fix the issue by directly connecting my AE to my MBP with an ethernet cable and using Airport Utiliites to reset the AE to factory conditions. I then had to reenter the various usernames & passwords on each of my connected devices, a pain but at least the AE now works well.

Similar Messages

  • Can't get airport express to connect to internet after ISP changed my modem

    Hi. My internet service provider installed fibre optic to my house, so they gave me a new modem. Have not been able to get airport express to connect to the internet ever since. Just get the flashing amber light. Other than paying $50 for phone support, I have no idea what to do. I just use the airport so I can play music from iTunes from my stereo using airplay. I use the airport utility on my laptop.

    Does the new modem provide a Wi-Fi network? If it does, and your only goal with Express is for iTunes streaming, the Express would just need to be reconfigured to join the new modem's wireless network. Please check out the following Apple Support article for details.

  • Airport express wont connect to internet

    i cant get my airport express to connect to the internet

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Continue with step 2 in the first set of steps.
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Can't stream music from iPhone to airport express when connected to internet

    I have an issue with my airport express. When the unit is used solely for streaming music from my IPhone to connected stereo speakers without an Ethernet cable attached it works fine.  When I attach an Ethernet cable to the airport express and connect to the Internet on my iPhone, the airport express will no longer stream music from the iPhone. This is a recent problem, previously I was able to access the Internet on my iPhone from the airport express, whilst simultaneously streaming music from the iPhone back to the airport express.

    Do you mean Lan cable? Can this be done wirelessly from itunes to airport express without the internet connections?  I can't connect to an airport express that's not connected to the internet.

  • Airport Express - cant connect to internet via PPPoE

    Hi guys/girls,
    I am having trouble getting internet access with my newly bought Airport Express 802.11n Wi-Fi. I was connected to the internet via an Arcor DSL-speed modem 200 (Arcor is my provider here in Germany), using the PPPoE protocol, and an Ethernet cable.
    I have set up Airport Express (AX) to use PPPoE, and managed to get a connection to the internet for about 5 seconds (even up to 20 secs once - YAY!)... before the connection drops again. AX tries continuously to connect to the internet, as if it is stuck in a loop, but never manages to make the connection last. The trouble I am experiencing look very much similar to what is described on the threads below from about 2 years ago. There it is suggested that the Firmware could be the problem. Or is it my provider?
    In German: http://www.macuser.de/forum/f15/arcor-speed-modem-178771/
    In English: http://discussions.apple.com/thread.jspa?messageID=1481024
    Since both posts are from 2 years ago, and I would have expected the problem to be solved. Apparently not. Any suggestions?
    cheers

    Yes - I was still old-school: plugging in my Ethernet DSL cable into my laptop every time, using PPPoE as that is what my internet provider requires.
    I have now indeed attached AX to my DSL modem via the Ethernet cable. Following your suggestion,I set-up a network location where PPPoE is disabled. But unfortunately no effect... After 5-15 secs (even up to 35 secs this time!) i get the message that my Ethernet is unplugged. Which it obviously is not, and I even cant blame the cat for it!
    Two problems keep being listed:
    Ethernet unplugged
    PPPoE server
    Could the problem be with my internet provider?

  • Airport Express Stopped Connecting to Internet, but Computer Says It Is

    Hi,
    I usually can find answers on these forums, through FAQs and troubleshooting, but this one's got me stumped. I've got an Airport Express Base Station. It worked great and then one day - it stopped working. Literally, I was online until about 12:30am, went to bed, and then at 10:00am the next morning all was lost. In the airport status in the menu bar, both my laptop (running 10.4.11) and my husband's (running 10.5.x - not sure which)show the base station is connected and working. In Internet Connect, it says the base station is working. But I cannot connect through Firefox, Safari or iChat. I know its not the cable modem because right now I'm directly connected through the ethernet line (and obviously it works since I'm on this discussion board). I've rebooted, my machine, the Airport Express, the cable modem about 20 times, in all different sequences, with the same results. I tried troubleshooting through Network System Preferences and still, a no-go. The funny thing is, if I plug in the printer and the ethernet line to the Airport Express, I can't connect to the internet but can print just fine. I've also tried to reboot the base station to Factory Settings and it doesn't seem to be doing that (plug it in while putting a paperclip in the reset button). Is it broken? Did it fry inside? Anyone have any suggestions? Help!

    Well, to anyone else that may have had this problem, I was able to reset the base station to its factory settings. Turns out I wasn't holding the reset button down long enough (duh). Went through Airport Setup Assistant and everything's working fine now. Phew!

  • Airport express cant  connect to internet through linksys wrt54g router

    Hi, i need some help.
    I have an airport express that i cant seem to get to connect to the internet.
    I have a cable modem to linksys wrt54g wireless router. An xp computer connected by LAN to the router.
    An Imac wirelessly.
    An xp laptop wirelessly.
    And a printer via the LAN
    All work just fine.
    But when i configured the aiport express to be a wds for the linksys to increase the range for my laptop or imac for that matter. It displays a green light, but has no connection, because it doesnt give the laptop or the imac a correct ip adress, that is what i seem to think the problem is.
    Please can someone help, i'm desperate.
    Thanks
    Core duo 17" IMAC   Mac OS X (10.4.7)  

    Did you follow instructions like this to add the AE to your Linksys network?
    http://www.macosxhints.com/article.php?story=20060609053254368&query=linksys%2Bw rt54g
    Also, make sure that "Distribute IP addresses" is NOT checked.

  • Airport express not connecting to internet

    I am switching from Clear to Comcast hopefully for faster, more reliable service.
    Connected the Comcast modem directly to my Mac Mini, activated...voila on the internet.
    Plug in Airport Express so that the Mini and my MBpro can share internet and a printer.
    AE powers up,gives the green light, but no internet service.
    System preferences>network states that WiFi has a self-assigned IP address of 169.254.xx.xx
    that will not connect to internet.
    With each reset the number changes slightly but still no internet.  I tried a manual number or 192.168.xx.xx
    and WiFi connects but still no internet. 
    1-1/2 hours with Comcast provided no help other than to call Apple.  Is this really that difficult? 
    With Clear it was a snap, but I am at the edge of the coverage zone and it sometimes fades.
    Please guide me through the steps.
    Thanks,
    JM

    I would recommend that you do the following as a minimum:
    Power-down the modem, AirPort base station, and computer(s).
    Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
    Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
    Power-up your computer(s).
    If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
    Disconnect the AirPort base station from the Internet broadband modem.
    While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref:Resetting an AirPort Base Station or Time Capsule)
    After the base station resets, go ahead and power it back down.
    Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
    Continue with step 2 in the first set of steps.
    In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

  • Blinking amber light, cannot update firmware on Airport Express

    Hey all:
    I can't find a prior question that addresses this problem exactly.
    A couple of weeks ago (about the time that AE Firmware was updated to 7.4.1) my AE started blinking amber. I was concurrently getting alerts that Airport Utility was finding a problem with my Airport Extreme, that it needed to have the firmware updated to the new version.
    When I try and update the firmware, though, the progress bar just zips along with nothing coming down. I can't get the update.
    This seems to have NO effect on my internet use, including three household computers connecting to the internet or to each other. I'm fine - but a little concerned.
    I tried to reset things manually, thinking if I start from scratch and basically reinstall the unit that would help, but it just kinds of spins its wheels and doesn't actually go into into settings windows.
    Ideas???
    Thanks much in advance
    Carlos

    You post may have more answers if posted in the airport section of the forum. That being said I would suggest you open airport utility select your base station and then from the base station menu choose restore default settings. Then try updating the firmware.

  • Just did firm ware update on time capsule an now my airport express not connected do to air port utilities doesn't support base station ??

    just did firm ware update on time capsule an now my airport express not connected do to air port utilities doesn't support base station ?

    mickair wrote:
    I have been experiencing some networking problems
    Welcome to Apple's discussion groups.
    I have the latest Time Capsule ("TC"), an old Airport Extreme Base Station ("AEBS") bought in 2007 and 2 Airport Expresses, one bought in 3 months ago ("AE-Alpha") and the other bought back in 2007 ("AE-Beta"). All of them have been updated with the latest firmware.
    Based on those dates, the AirPort Extreme is probably flat (as opposed to dome-shaped), making it 802.11n-capable. The Newer AirPort Express is probably an 802.11n-capable model A1264, while the older one is probably a model A1084 or A1088.
    I use {the TC's} DHCP function ... to avoid unauthorized use.
    This a discussion for another thread, but that's not what DHCP is for.
    The wireless setting for it is to participate as WDS Main, but after reading various posts, it seems WDS is a bad idea
    With that older AirPort Express you're stuck with WDS unless you decide to replace it with a newer model.
    The AEBS is currently setup as being a WDS Relay at the moment
    Why a relay? That's only needed if there's another base station "beyond" it that is configured to depend on it.
    Since the AEBS is connected to the TC via Ethernet, you should probably configure it as a "roaming network":
    http://discussions.apple.com/thread.jspa?threadID=2273124
    {The AE-Alpha} connects fine as WDS remote at the moment
    I don't have any experience with mixed WDS and non-WDS networks, but since it's 802.11n-capable, you may be able to configure it to "extend" the network of the TC rather than as WDS. Look for a setting on the TC to "Allow this network to be extended".
    Physical location:
    AEBS in one end, TC and AE-Alpha in the middle while AE-Beta on the other end.
    A device such as "AE-Beta" that's supposed to extend a network shouldn't be "at the end" but should be half way between the central base station and the clients that need an extended network.

  • Having trouble with my Airport Utility not supporting either of my Airports Expresses or Basestation. Do i have to update Firmware of airports or is the issue with my version of Utility which i believe is the latest. Thank you.

    having trouble with my Airport Utility not supporting either of my Airports Expresses or Basestation. Do i have to update Firmware of airports or is the issue with my version of Utility which i believe is the latest. Thank you.

    AirPort Utility in Mountain Lion will not support the older versions of the AirPort Express.....model numbers A1084 and A1088. Check on the side of the Express for the model number.
    In addition, AirPort Utility in Mountain Lion will not support the older "round" or "dome" shaped versions of the AirPort Extreme.
    Can you check to see how your devices might be affected?

  • How do I use the airport express to connect a remote PC via ethernet cable and access the internet via wireless connection, How do I use the airport express to connect a remote PC via ethernet cable and access the internet via wireless connection

    Trying to connect my xbox to the airport express. Have wireless in home and do not have a ethernet point behind tv/xbox. How do I configure the airport express to connect to my wireless network and then the airport express can use its connection via ethernet to connect the xbox to the internet.

    Is your AirPort Express Base Station (AX) a 802.11n model? If it is, you can reconfigure it as a wireless Ethernet bridge or ProxySTA. This would allow the AX to join another wireless network and have its Ethernet port enabled for wired clients, like the Xbox 360.
    To activate ProxySTA, you must set up the Express to join a wireless network and then enable the Allow Ethernet Clients setting; both settings are located in the Wireless tab of AirPort Utility.

  • Can I use the Airport Express to connect to a Linksys Wireless Network and then use the Ethernet port on the Airport for a wired connection to a device for internet access?  Would I be able to then also use that Ethernet pt to a Ntwk Hub for more wired c

    Thanks for the help.  Looked but not clear on what I am trying to do as being possible.  Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it? 
    I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located.  Would prefer to replace Linksys with all Apple, but just not possible financially yet.  Thanks for the help.

    If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.

  • I can print from my macbook pro using airport express usb connected printer, however my iPad is looking for an airprint printer.  Can I direct the iPad to the usb connected printer.  Both macbook and iPad confirm a wifi connection through the airport exp.

    I can print from my macbook pro using airport express usb connected printer, however my iPad and iphone are looking for an airprint printer.  Can I direct the iPad/iphone to the usb connected printer.  Macbook iphone and iPad confirm a wifi connection through the airport express.

    You will need to install an App like Print Central on the iPad to try to print to the printer. It will allow you to print to most printers. Check with their support folks if you need more info.
    PrintCentral for iPad on the iTunes App Store

  • Do I need to have Airport Express to connect to other computers on our homer network?

    Do I need to have Airport Express to connect to other computers on our homer network?

    Not necessarily. You could use the "Create Network" feature of your MBP's built-in AirPort card to provide an Ad-hoc wireless network for local wireless-capable computers to connect to.

Maybe you are looking for