Updating iphone drivers access denied
My iphone wont connect to itunes it doesnt even show up, my computer makes the noise when I connect it but the iphone is unresponsive, it wont even charge it. I tried all the usb cables in my house, then went so far as to buy two new ones incase that was the problem...it was not.
I apparently dont have the right drivers installed for my iphone.
I read through this http://support.apple.com/kb/TS1538 and the iphone usb driver isn't even under 'Universal Serial Bus Controllers' its under 'Other Devices' and it has a yellow exclamation point, when I right click the click on properties it says;
The drivers for this device are not installed. (Code 28)
Access is denied.
To find a driver for this device, click Update Driver.
So naturally I click update driver but it says access denied again, so I went through the support article linked above found the "usbaapl64" file and tried updating that way, I still get access is denied and of course my luck the article covers error code 52 but not 28...Theres nothing there to help me figure out why it says access denied or where to go from this point. All help would be greatly appreciated.
Hy there,
In order for you to solve this problem you have to follow these stept if your running windows:
1'st step is to go into the device manager
2 step is to go to portable devices (it is rught under network adapters)
3 step is to right clic apple iphone and click update drivers
4 step is to brows your drivers from C:\Program Files\Common Files\Apple\Mobile Device Support\Drivers
After that your itunes will pump up alown and youl see your iphone right there.
Good luck and sry for my bad righting.
Andrei
Similar Messages
-
HT4623 Iphone 4s access denied error message when importing photos
ok got iphone 4s in feb have used windows live photo gallery to import since i got the phone and never had any problems started having problems with itunes not working say it was on a locked disk and/or didint have write permissions fixed this with a total uninstall and reinstall of itunes and now that works fine but at the same time the itunes stopped working i started getting an access denied error when importing photos via usb via windos live photo gallery i was however able to import my husbands photos from his ipad three days ago the same way i do my iphone and it worked fine with the ipad but not my iphone so here is what i do click for click i plug in the iphone via usb and the autoplay and itunes starts. i close itunes and go to autoplay click on import using windows live photo gallery than the pops open i check the folder to import too (which is on an exterial hard drive) and then i click import and it starts to import and on the very first photo and all photos the access is denied error message pops up help please this is driving me crazy that it worked fine one day and now it doesnt work
Good afternoon
There seem to be a number of possibilities.
Here is a thread that conatins a number of solutions. The most common one is to load 50 pics at a time.
https://discussions.apple.com/thread/3947440?start=0&tstart=0
Hope this helps -
Cannot install any device drivers - access denied
Hi,
Anytime I plug a device into my usb port/s and it tries to load the driver it fails. I've also tried directly installing the driver and I get access denied. Can anyone help me resolve this please?
I have windows 7 home laptop, I am the administrator.
Thanks
CasHi,
Please try to replaces ACLs with default inherited ACLs for all matching files:
1. Open an elevated command prompt, go to the drive:
cd /d X: (X represent your problematic drive letter, here I recommend the OS drive)
2. Type the following command:
icacls * /T /Q /C /RESET
You could also refer to the following article:
Icacls
Karen Hu
TechNet Community Support -
Cannot install drivers - Access denied (exteral hdd)
Hey there, i have a serious problem with my brand-new exteral hard drive (toshiba STOR.E canvio, it works with usb 3 ''AND'' usb 2). It works fine with my old windows XP laptop.
When i connected it on my new pc, it worked. But i could not find it on My Computer.
Finnaly i found it like an ''unknown external USB 3''. I tried to install the drivers, but i failed. A message appeared: ''Windows found drivers''. But drivers were not installed. The problem:
!!!ACCES DENIED!!!
PLS HELPHello! After 4 days of searching and searching, i found the solution.
1. Restart your PC.
2. Before the windows logo appears, press F8.
3. Select Safe Mode.
4. Install drivers.
5. Restart your pc, this time in normal mode.
6. Plug your HDD
7. ENJOY!!! -
I can't seem to connect my iPhone 5 to windows 7, it shows up under unspecified in the control panel but when I try to update the drivers it says access denied! Been at this for 3 days now! Tried numerous fixes, any help please?
The iPhone 5 and iOS 6 require iTunes 10.7. Depending on what OS you have for your comptuer, could restrict you.
Windows System Requirements
PC with a 1GHz Intel or AMD processor and 512MB of RAM
Windows XP Service Pack 2 or later, 32-bit editions of Windows Vista or Windows 7
64-bit editions of Windows Vista or Windows 7 require the iTunes 64-bit installer
250MB of available disk space
Broadband Internet connection to use the iTunes Store
Macintosh System Requirements
Mac computer with an Intel Core processor and 512MB of RAM
OS X version 10.6.8 or later
Safari 4.0.3 or later
400MB of available disk space
Broadband Internet connection to use the iTunes Store -
Hi everyone
Need some help desperately
Was syncing my iphone through itunes and it wanted me to update the version which I thought it did
Now my phone keeps telling me to connect to itunes which I have tried without success.
In device manager it's showing as apple mobile device in recovery mode with an exclamation mark
Have tried so many options from this site but nothing works.
When I tried to update in device manager it says access denied
Have also tried reboot without success
Going absolutely mad need a real expert
Pleeeaaase thanksHi Brenni17,
If you had an issue during an update and now having issues restoring your iPhone, you may find the troubleshooting steps outlined in the following article helpful (apologies if you have already seen it):
Apple Support: If you can't update or restore your iOS device
http://support.apple.com/kb/ht1808
Regards,
- Brenden -
"Access Denied" error when attempting to update HP w2207h monitor drivers
CPU Product Name and Number: HP Pavillion a6700y
Monitor: HP w2207h
Operating system: Windows Vista 64-bit. SP2
Error Message: I receive an "Access Denied" error screen when attempting to update drivers for my HP w2207h monitor. HP solution of deleting monitor(s) from Device Driver and reloading did not work. Patch file called DRVFix download can not be opened by WINZIP. I have tried reloading from the original w2207h monitor disk but receive the same error. Attempting to download from Windows Update results in the same error. Any suggestions? ;
Recent Changes: Installed new hard drive to replace an "imminent failure" drive; used system recovery disks and am now reloading all software. All works week except fro this driver issue with the monitor. All Microsoft and Windows security and hotfix updates have been installed. System is wireless.Hi,
I solved the issue of Access Denied by installing the driver (inf file) manually.
Go to Device Manager and locate the Monitor
Right mouse click and select update driver software
Browse my computer
Select let me pick from a list
Select have Disk
Browse to C:\swsetup\monitors\HP_2159_2.0\files\
Select HP_2159.inf
Click to install from disk
Next
You might even be able to just navigate directly to the HP folder, locate the .inf file, right mouse click on it and select install.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
Access denied error while trying to install graphics drivers
Hello,
I have a new toshiba laptop P70-A. I have installed windows 7 and the pc was working excellent up until now. Noticed yesterday that the nvidia automated system failed to install the new update. When I tried to install the new driver manually, even from the
device manager, I got the access denied message.
A day now wasted reading all the possible causes and solutions but with no luck. Read all the forums and all the posts, tried almost everything. Below youll find everything I tried as a solution and failed.
1.Disabled UAC
2.Enabled the administrator account and trying to take control from there
3.Run the subinacl and the reset.cmd
4.Tried manually to take control the folder windows (and access denied while changing the rights)
5. Scanned the system with everything there is available ( Kaspersky, MalwareBytes, RegCurePro, Tuneup Utilities, CCleaner) The system came out clean.
6. Tried restoring the system to an earlier time (got again access denied error code 0x80070005)
7. Checked all the group policies (all seem to be fine)
8. Run a script to take immediate ownership over all of C:
TAKEOWN /A /F C:
then the next one
TAKEOWN /F C:
9. With subinacl I run all the above scripts... (still nothing changed)
@echo off
title Resetting ACLs...
echo.
echo Determine whether we are on an 32 or 64 bit machine
echo.
if "%PROCESSOR_ARCHITECTURE%"=="x86" if "%PROCESSOR_ARCHITEW6432%"=="" goto x86
set ProgramFilesPath=%ProgramFiles(x86)%
goto startResetting
:x86
set ProgramFilesPath=%ProgramFiles%
:startResetting
echo.
cd /d "%ProgramFilesPath%\Windows Resource Kits\Tools"
echo.
echo Resetting ACLs...
echo (this may take several minutes to complete)
echo.
echo IMPORTANT NOTE: For this script to run correctly, you must change
echo the values named Athena to be the Windows user account that
echo you are logged in with.
echo.
echo ==========================================================================
echo.
echo.
subinacl /subkeyreg HKEY_CURRENT_USER /grant=administrators=f /grant=system=f /grant=restricted=r /grant=Athena=f /setowner=administrators > %temp%\subinacl_output.txt
echo.
echo.
subinacl /keyreg HKEY_CURRENT_USER /grant=administrators=f /grant=system=f /grant=restricted=r /grant=Athena=f /setowner=administrators >> %temp%\subinacl_output.txt
echo.
echo.
subinacl /subkeyreg HKEY_LOCAL_MACHINE /grant=administrators=f /grant=system=f /grant=users=r /grant=everyone=r /grant=restricted=r /setowner=administrators >> %temp%\subinacl_output.txt
echo.
echo.
subinacl /keyreg HKEY_LOCAL_MACHINE /grant=administrators=f /grant=system=f /grant=users=r /grant=everyone=r /grant=restricted=r /setowner=administrators >> %temp%\subinacl_output.txt
echo.
echo.
subinacl /subkeyreg HKEY_CLASSES_ROOT /grant=administrators=f /grant=system=f /grant=users=r /setowner=administrators >> %temp%\subinacl_output.txt
echo.
echo.
subinacl /keyreg HKEY_CLASSES_ROOT /grant=administrators=f /grant=system=f /grant=users=r /setowner=administrators >> %temp%\subinacl_output.txt
echo.
echo.
echo System Drive...
subinacl /subdirectories %ProgramFilesPath%\ /grant=administrators=f /grant=system=f /grant=users=e >> %temp%\subinacl_output.txt
echo.
echo.
echo Windows Directory...
subinacl /subdirectories %windir%\ /grant=administrators=f /grant=system=f /grant=users=e >> %temp%\subinacl_output.txt
echo.
echo.
echo ==========================================================================
echo.
echo FINISHED.
echo.
echo Press any key to exit . . .
pause >NUL
Im frustrated really... ANY help at all would be really appreciated.
Thanks in Advance and sorry for the long post
AthenaHello,
Thanks for the replies, i much appreciate it. I tried all of the above with no luck again. Safe mode allows me though to install drivers but thats reverting the moment im entering windows. Im always running commands and programs as a administrator or in
the Admin enabled account.
It seems the problem is solved today. Via tune up utilities I disabled most of the startup programs and services and it seems that 1 service is causing this issue. Although I havent played much with the disabled services but 3 remain to be checked. One of
the three is causing this.
Thanks again guys and Ill keep you posted about the soft. conflict.
Athena -
G580 Can't Update Driver - "Access Denied"
I'm trying to update my drivers which was successful apart from the one for the Synaptics touchpad. It starts to install but eventually aborts saying 'Access Denied' to a file called Thumbs...
My touchpad works fine but I thought it was always best to update the drivers? I was hoping the new driver would include a few more options for the touchpad as my old Acer laptop had a synaptics touchpad but with many more options to configure. I'm using the official driver from this site and I've double checked I've downloaded the right one for Windows 7. I'm already logged on as administrator and I've tried opening the setup file as an administrator but nothing works.
Does anyone know what the problem could be? Is it even worth updating this particular driver, the one on my system dates back to April 2011.
Thank you in advance for any suggestions.guess that your account was in Local Admin group...?
This is because all accounts in local Administrators group are working as standard accounts. When an Administrator action need to be performed, a prompt will occurs for permission to promote to admin permission. As only Administartors
group has permission on a folder and the account we are using is working like a standard account, we will be denied from accessing.
run all accounts in Administartors group in Admin mode...http://technet.microsoft.com/en-us/library/dd835564(WS.10).aspx can
be OK?
for PolicyDefinitions, group policy location... suggest to use central store...
http://blog.mpecsinc.ca/2009/06/sbs-2008-create-group-policy-central.html
Best,
Howtodo -
Why do I get general access denied trying to update my own field in Active Directory?
I am trying to update a field pertaining to my own user object in Active Directory using ADSI and C++ app. The operating system
is Windows Server 2012 Standard.
I am able to read, I am able to call Put without problems, but when I call SetInfo, it returns with "General access denied". I have
confirmed that it's my own user object I'm trying to access.
I obtain my own FQDN like this:
GetUserNameEx(EXTENDED_NAME_FORMAT::NameFullyQualifiedDN, pszFullyQualifiedDN, &dwFullyQualifiedDN);
Then I use it like this:
LPTSTR pszObj = (LPTSTR)LocalAlloc(LPTR, dwMemToAlloc);
wcscpy_s(pszObj, dwMemToAlloc / sizeof(TCHAR), L"LDAP://");
wcscat_s(pszObj, dwMemToAlloc / sizeof(TCHAR), pszFullyQualifiedDN);
I bind to an object like this:
ADsGetObject(pszObj, IID_IADs, (LPVOID*)&pObject);
This call succeeds:
pObject->Get(CComBSTR("Description"), &var);
This call also succeeds:
VariantClear(&var);
V_BSTR(&var) = SysAllocString(L"Some new value");
V_VT(&var) = VT_BSTR;
hr = pObject->Put(CComBSTR("Description"), var);
Trying to commit the above change using the following:
pObject->SetInfo();
This is where it fails.
It returns E_ACCESSDENIED General access denied error.
As you can see, that is my own user object I am trying to update. To my understanding that is supposed to work provided I am a member of Domain
Users group. Which I am.
What could possibly be the problem?The problem is that in Windows Server 2012 Domain Controller, permission to write to public (and personal,
for that matter) properties is not granted to "SELF". The field I am trying to write to belongs to public properties. The only property set a user is able to change for himself in Windows Server 2012, by default, seems to be "Private-Information",
which consists of ms-PKI-Credential-Roaming-Tokens,ms-PKI-RoamingTimeStamp, ms-PKI-DPAPIMasterKeys, ms-PKI-AccountCredentials
Why on earth a user doesn't have permission to write to his own personal fields in Windows Server 2012 AD, Microsoft??!?!?! -
Access denied error on updating list through custom webpart
hi
I have created one webpart having multiple view option.
On selection of items from one view user is clicking on next button to get 2nd view (THis is causing postback) and on selection of 2nd view items user is clicking on next buton for 3rd view.
On third view he can see the submit button. On click on submit button the selected items are updateing in one list and also updating data in other lists.
The list in which we are updating data have limited access to all users. But previously user were able to upate the list.
But after implimenting this multiple view with next button which postbacks on click user are getting access denied error while updating the list. If i provide contribute access to that list then they able to submit the changes properly. But even after
that they got the error at first time.
Any body got this type of issue?
Is the post back on custom webpart cause access denied error?
i have written my code like this to updat list,
protected void btnUpdate_Click(object sender, EventArgs e)
try
SPSite site = new SPSite(SPContext.Current.Site.ID);
SPWeb myWeb = site.OpenWeb(SPContext.Current.Web.ID);
SPSecurity.RunWithElevatedPrivileges(delegate()
using (SPSite ElevatedSite = new SPSite(site.ID))
using (SPWeb ElevatedWeb = ElevatedSite.OpenWeb(myWeb.ID))
ElevatedSite.AllowUnsafeUpdates = true;
ElevatedWeb.AllowUnsafeUpdates = true;
//code to update multiple lists
catch (Exception ex)
Please suggest any solution for this.Yes I checked with ULS log viewer.
Its very helpfull as reading that text log file is very difficuelt.
I found that if user spend more time on that webpart then session veriables on that webpart gets expired and at the time of redirection of user to newly created list using below code currentNewList becomes empty and its redirection to wrong list(_abc) which
is dummy list and user dont have any access.
currentNewList = NewListName+ "_abc"
SPUtility.Redirect(currentNewList.DefaultViewUrl, SPRedirectFlags.Default, HttpContext.Current);
So I modified the code to reload the session data when user clisk on submit button. -
While trying to schedule Update stats db13 : getting access denied
HI Experts
I have scheduled update statistics for all tablespaces in DB13 transaction of ECC system. Once the job completed, ended with below error, saying "Access Denied". But this SAP is on Windows system.
Job started
Step 001 started (program RSDBAJOB, variant &0000000000008, user ID GRCUSER)
Execute logical command BRCONNECT On host GRC10DCSWS
Parameters: -jid STATS20140606020000 -u / -c -f stats -t ALL
BR0801I BRCONNECT 7.20 (29)
BR0252E Function CreateFile() failed for 'E:\oracle\G10\11203\database\spfileG10.ora' at location BrFileStatGet-2
BR0253E errno 5: Access is denied.
BR0273E Determination of file status for E:\oracle\G10\11203\database\spfileG10.ora failed
BR0806I End of BRCONNECT processing: cenzzwvg.log2014-06-06 02.00.16
BR0280I BRCONNECT time stamp: 2014-06-06 02.00.16
BR0804I BRCONNECT terminated with errors
External program terminated with exit code 3
BRCONNECT returned error status E
Job finished
Pl suggest in this regards.
Regards
Vyjayanth MFor general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down page in case one of them applies.
Your library should be unaffected by these steps but there is backup and recovery advice elsewhere in the user tip.
tt2 -
Can't open ANY pdf files. Updated to 10.1.8--still "Access Denied."
Hello everyone,
I am currently unable to open any PDF files.
I recently did a clean re-install of Windows 7 (restored my Toshiba Satellite to out-of-the-box state).
After that, I restored all of my personal files from an external HD.
Now, every time I try to open a PDF, Adobe Reader gives me the following message:
"There was an error opening the file. Access denied."
The only solution I've been able to find online has been this:
Edit > Preferences > General> Clear "Enable Protected Mode at Startup"
Also,
Edit > Preferences > Security (Enhanced)> Clear "Enable Enhanced Security"
Neither of these has fixed my problem.
I also updated to the lastest version--10.1.8--with no success.
I also re-downloaded and installed PDF Creator and its companion, PDF Architect. Curiously enough, I can't open any PDF in that program either. I'm not sure if there is some global setting I'm missing or something.
Access to these files is critical to my work, so any help is appreciated!
Thanks,
LaurenI updated from within the Adobe Reader X program (Help > Check for Updates) and it tells me: No updates available. Installed: Adober Reader X (10.1.8) MUI
Is 11.0.5 something I would have to access another way?
Also, I'm still not sure if that would fix my problem. It seems most people with the "Access Denied" error had it fixed with the very first 10.1 update, and I have 10.1.8, so I'm not sure what's causing mine. -
Publishing cancels with "access denied" error when publishing updates to desktop layout
Hello, all,
Wondering if anyone else has run into this issue: we update and republish our help projects frequently. We're currently using a layout based on the desktop layout (colors, fonts, and some other screen elements have changed). The project generates successfully. We publish via file transfer and have the "republish all" setting selected. Sometimes when we publish our multiscreen HTML5 layout, it cancels about halfway through the estimated time with a "publishing cancelled - access denied" error. If we delete the layout folder ("desktop" in this case) from the publishing location and retry publishing, it succeeds.
Has anyone else encountered this issue? If so, what fixes (other than deleting content and republishing) have you found?
FYI, we also publish the same projects to the WebHelp Pro layout without any issues.
Thanks in advance for your help.This problem used to occur with Publishing from Rh but I have not seen it for a long time, either myself or in posts.
Maybe Item 5 at http://www.grainge.org/pages/snippets/snippets.htm#webhelp will help.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge -
I updated iphone 4s to 7.02 and now cannot access icloud server.
I updated iphone 4s to 7.02 and now cannot access icloud server.
One of these:
Restart:
1. Press and hold the Sleep/Wake button until the red "slide to power off" slider appears, and then slide the slider.
2. Press and hold the Sleep/Wake button until the Apple logo appears.
Reset: Hold down the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Note: You will not lose any data
Restore from backup
Restore as new
http://support.apple.com/kb/HT1414
Maybe you are looking for
-
Apple iPhone 4 Dock not working with Apple A/V Component Cables.
Okay, Got a problem here, or I think its a problem. I purchased the iPhone 4 dock and the A/V component cables with power connection. When I connect the A/V cables to the iphone, they work fine and I see the video and hear the audio on the tv. When I
-
How do i stop getting emails sent from apple community, any help please
Hi, how do i stop the emails from Apple support community any help please!!!
-
HP2610 cannot print -network - wired - cannot see printer - Win7 64bit
In the solution center I get message that the system cannot see my HP Photosmart 2610. I can however ping the printer with no issues. I can also print if I use the USB connection. This has worked for a couple years without issue, this problem suddenl
-
Multithread program with socket, help me
Hi all, I have had some troubles with my multithread program, that is when I make 4 threads to send messages to 4 accepted ports: 2001, 2002, 2003 and 2004, it leads to the error: "Java.net.SocketException: Software caused connection abort: recv fail
-
When I try importing certain songs I get this annoying error message: http://img365.imageshack.us/img365/3083/errorga4.png