Updating to 9.2 caused error to boot up

I ran Software update on my 8600 to get OS 9.2.2 from OS 9.2.1 and at the ending came up with an error message and froze. I get " Cant reboot from this update."
My CDrom drive is acting up, it wont reboot from my original disc. I tried the C key reboot and nothing. I'm going to let it sit over night and try again. Any ideas why I cant see the OS 9.2.2 update?

Your 8600 isn't officially supported to run OS 9.2.1/9.2.2. You need to download and run the "OS9 Helper" utility to update OS 9.1 on your Power Mac.

Similar Messages

  • BCDEDIT.EXE /CREATESTORE causes error the boot configuration store could not be opened

    I'm upgrading XP to Windows 7 with dual boot using an image and successfully installed on 6 other computers, the last two are failing when I issue the command:
    bcdedit.exe /createstore
    The boot configuration data store could not be opened.
    The requested system device cannot be found.
    I'm using a known good WINPE 4.0 (Windows 8) x64 USB boot environment, so most solutions that state to run elevated as an administrator do not apply.
    C: is NTFS active partition, chkdsk doesn't find any errors on C:
    I've updated the bootsector with the command
    bootsect /nt60 c: /force /mbr
    this of course disables booting into XP, but I can reboot and re-enable XP via
    bootsect /nt52 c: /force /mbr
    If I try a modified command
    bcdedit.exe /createstore c:\BOOT\BCD
    this also fails, and I've verified that the hidden system C:\BOOT folder does not exist before issuing the command
    If I pre-create c:\BOOT (w/o hidden or system attributes) the command
    bcdedit.exe /createstore c:\BOOT\BCD
    does run successfully, but the following commands to add the Windows 7 boot entries and legacy NTLDR for XP dual boot still fail!
    bcdboot.exe d:\windows /s c: /v
    bcdedit.exe /create {ntldr} /d "Windows XP SP3"
    bcdedit.exe /set {ntldr} device partition=C:
    bcdedit.exe /set {ntldr} path \ntldr
    bcdedit.exe /displayorder {ntldr} /addfirst
    bcdedit.exe /default {ntldr}
    bcdedit.exe /timeout 5
    The two failing computers are older Dell OptiPlex 960 models, so I'm using traditional BIOS boot, EFI is not supported on these models.  Hard drives are regular SATA (1 per computer), no other mass storage devices present besides DVD (empty), and hard
    drives are not GPT formatted.  Drives are old enough that they are regular 512 sector devices (no 512 emulation or 4K issues).

    Thanks for your response Niki Han, the current status is the computers are booting correctly into the original XP SP3, since I've started them with my WINPE
    4.0 x64 USB flash  drive and issued the command to restore the original NTLDR boot process "bootsect /nt52 c: /force /mbr".
    I also verified that there are no hidden partitions, and that there is only one active partition, C: which is a standard NTFS volume:
    Partition 1
    Type  : 07
    Hidden: No
    Active: Yes
    I've also verified that the BIOS is the same and the hard drive mode set in the BIOS is the autodetect RAID in both the working and non-working systems.  I'll review the article you provided at
    http://technet.microsoft.com/en-us/library/ee829686(v=ws.10).aspx#BKMK_Step4
    which may allow me to get these two systems dual booting.  I do know that I'll need to delete the corrupted hidden system c:\Boot folder to avoid any issues.
    I do want to figure out why the command
    bcdedit.exe /createstore
    is outputting this error on just these two systems:
    The boot configuration data store could not be opened.
    The requested system device cannot be found.
    What exactly does bcdedit.exe do when given the /createstore command, does it create a new empty store from the exe itself, or does it copy a store from the running system?  I think the key to figure this out is understanding what the error "The
    requested system device cannot be found." is trying to tell us.

  • Updating Acrobat 9.0 causes error "Acrobat.exe - Bad Image"

    Full error is:
    Acrobat.exe - Bad Image
    C:\Program Files (x86)\adobe\acrobat 9.0\acrobat\BIB.dll is either not designed to run on Windows or it contains an error. Try installing the program again using the original installation media or contact your system administrator or the software vendor for support.
    Running repair doesn't fix it, only un-installing it and re-installing from scratch. This happens on multiple machines with the same result. As soon as the update is ran it no longer opens and has the error.
    I've tried manually updating it version to version starting at the first 9.1 release but I run into the same error after installing the first update. Uninstalling Acrobat after manually running the first update produced another error durring uninstallation. Error 1905.Module C:|Program Files (x86)\Adobe\Acrobat 9.0\Acrobat\authplay.dll failed to unregister. HRESULT -2147220472. Contact your support personnel.
    System is Windows 7 Enterprise 64bit running on a VDI in a box from Citrix. Version of Acrobat is Pro.
    Any thoughts or ideas on this would be great, thanks.
    Joel

    Are you running updates from the Help menu in Acrobat or by downloading the updates. When you have problems, it is probably best to try running the updates as downloads from http://www.adobe.com/support/downloads/product.jsp?product=1&platform=Windows. You will need to generally install the updates in order. You would reboot after the last update.

  • Updating Adobe XI Pro causes Error 16

    Every time I try and upgrade my XI pro beyond 11.0 I get the error 16 and I have to reload. I'm running Win7 64 Ultimate. I have tried some of the permission fixes but nothing worked. I turn the updates off and I still get nag notices.
    Any help would be great

    Hi mancinjm1,
    Please try the troubleshooting steps mentioned in the KB Doc :http://helpx.adobe.com/x-productkb/policy-pricing/configuration-error-cs5.html
    Regards,
    Rave

  • Update 17.0.1 causes errors while launching Illustrator

    Since doing the latest Illustrator CC update yesterday, I can't open the application as it says that the font Verdana needs to be activated - I have the latest version of Suitcase Version 5 & it says that Verdana is permanently activated (Tahoma too, I read this is another thread here, it is permanently enabled), I've tried a shutdown & restart, an uninstall & reinstall of Illustrator CC from Creative Cloud & still it won't work. Any suggestions? I've had issues with CC & font activation for some unknown reason, I have the latest version of Suitcase Fusion 5 which I thought would fix any problems (instead seems to have created them)

    Hi Personified & Monika,
    Personified with the AI CC latest update on MAC 17.0.2 you need not to disable any of your fonts. Just check that all the 4 fonts of Verdana family are present and are in enabled state in the System Fonts folder.
    @Monika: Thanks a lot for sharing the thread but that thread was more related with the crash issue on MAC with 17.0.1 update which AI team has fixed in 17.0.2 update.
    With Best Regards,
    Raghuveer

  • Installed Trend Micro Smart Surfing on new MacBook Pro and now it has caused error that won't let computer boot up.  How do I get it to a point that I can delete program?

    Installed Trend Micro Smart Surfing on new MacBook Pro and now it has caused error that won't let computer boot up.  How do I get it to a point that I can delete program?

    Try booting up in Safe mode (holding down the Shift key while booting). If the software came with an unistaller, use it to remove alll traces of the software - it's nothing that you need and, as you've experienced, can do more actual hard than good (as is the case with most software of this type). When you're booted in Safe Mode, if you can't run an uninstaller, at least check to make sure that there are no Trend Micro items that are set for automatic log in, at least.
    Clinton

  • November updates cause error in IE group policy files

    Hi,
    I reinstalled Windows 8.1 with Update today and noticed an error after installing either the IE 11 cumulative update or the optional November rollup update package. The error pops up only if either or both are installed. If they are uninstalled, the error
    no longer appears.
    The error pop up displays when group policy editor is opened,
    "Resource '$(string.VerMgmtAuditModeEnable)' referenced in attribute displayName could not be found. File C:\windows\PolicyDefinitions\inetres.admx, line 1495, column 249."

    Hi Sahil,
    This issue is related with the ADMX files of Internet Explorer. The error was often caused by mis-matched ADMX and ADML files.
    Here is a similar thread for reference: Group Policy Editor problem
    The fix:
    Unzipping the download (THIS ONE
    http://www.microsoft.com/en-us/download/details.aspx?id=40905), then copy the related language\inetres.adml file to the c:\Windows\PolicyDefinitions\language directory, overwriting the existing one in the destination.
    Best regards
    Michael Shao
    TechNet Community Support

  • The recent software update on my HTC One has caused errors with Exchange ActiveSync issues. Calendar, mail and tasks sync fine but contacts won't sync. How do you correct this?

    The recent software update on my HTC One has caused errors with Exchange ActiveSync issues. Calendar, mail and tasks sync fine but contacts won't sync. How do you correct this?

    I had the same problem.  Here is what worked for me.  Open the mail app and delete your exchange account (Settings > Delete Account).  Then re-add your Exchange account.  After this my Exchange contacts showed up again. 

  • Did recent recommended update cause incompatibility with HP printer, causing error message and printer to print blank pages?

    did recent recommended update cause incompatibility with HP printer, causing error message and printer to print blank pages?

    Why not contact HP tech support for assistance since they make the printer. While on their site you can look for an updated printer driver. Otherwise, try deleting the current installed driver, reset the print system, then reinstall your printer's driver.
    Mac OS X- How to reset the printing system

  • HT201413 My ipod is a 4.3.5 and im trying to update it but cant cause is freezes on turn i try rebutting it does not wrok so i try restoring it and it wont even let me do that what do i do it just keep popping up a error code 3194 please help

    my ipod is a 4.3.5 and im trying to update it but it keeps freezing on me so i try restoring it but it just keeps puting error code 3196

    Have you checked the Apple support site? If not, take a look at this -> iTunes: Specific update-and-restore error messages and advanced troubleshooting
    Unable to contact the iOS software update server gs.apple.com
    Error 1004, 1013, 1638, 3194: These errors may be the result of the connection to gs.apple.com being redirected or blocked. Follow these steps to resolve these errors:
    Install the latest version of iTunes.
    Check security software. Ensure that communication to gs.apple.com is allowed. Follow this article for assistance with security software. iTunes for Windows: Troubleshooting security software issues.
    Check the hosts file. The restore will fail if there is an active entry to redirect gs.apple.com. Follow iTunes: Advanced iTunes Store troubleshooting to edit the hosts file or revert to a default hosts file. See section "Blocked by configuration: (Mac OS X/Windows) > Rebuild network information".
    Try to restore from another known-good computer and network.
    If the errors persist on another computer, the device may need service.
    If you've used some progam with your iPod that wasn't made by Apple, it might have modified the host file.

  • Error while booting maverick

    error while booting maverick

    The most likely causes of this error are:
    1) Failing to execute tmloadcf after updating the UBBCONFIG file.
    2) Failing to set TUXDIR correctly in the UBBCONFIG file.
    3) Failing to set TUXCONFIG, PATH, or
    LD_LIBRARY_PATH(Unix)/SHLIB_PATH(HP)/LIBPATH(AIX) correctly in your
    enviroment.when executing tmboot or tlisten.
    You should verify that your environment is set correctly and you should
    execute tmunloadcf to see the contents of the configuration file that has
    been loaded.
    Ed
    <Kaustubh Deoghare> wrote in message news:[email protected]..
    Hello,
    I am getting following error while booting tuxedo
    exec TMS_ORACLE8I -A :
    TMS_ORACLE8I: symbol lookup error: TMS_ORACLE8I: undefined symbol:
    kgsmp789_compat_
    CMDTUX_CAT:819: INFO: Process id=2568 Assume started (pipe).
    Though I have installed Oracle9i, in ubbconfig it is still taking
    TMS_ORACLE8I and hence trying to access Oracle8i library files.
    Pl suggest in this regard
    Thanx in advance

  • Errors At Boot

    I should preface this with I'm not a Linux noob, but I am no expert either (I get by).  Also I hope this is the right forum to post in. So after I updated about a week ago I start seeing errors at boot.  Never could quite see exactly what they were so today I logged dmesg to a text file.  I should also say the only real problem I have seen outside of the errors showing is Plex Media Server having an issue streaming my media that is kept on a separate hard drive from the main system.  After the errors show the system continues to boot to Openbox.  I was hope someone could tell me what the errors are and how to not get them anymore.  I have posted the dmesg log below, thanks in advanced for any help.
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.12.1-1-ARCH (tobias@T-POWA-LX) (gcc version 4.8.2 (GCC) ) #1 SMP PREEMPT Thu Nov 21 08:18:42 CET 2013
    [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=f3bb4b9d-d9f1-4ef7-9180-07f1d4a00fc2 rw quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffdffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000bffe0000-0x00000000bffe2fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000bffe3000-0x00000000bffeffff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000bfff0000-0x00000000bfffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013fffffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.5 present.
    [ 0.000000] DMI: Unknow Unknow/HA04, BIOS 6.00 PG 04/16/2008
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x140000 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-C7FFF write-protect
    [ 0.000000] C8000-FFFFF uncachable
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0000000000 mask FF80000000 write-back
    [ 0.000000] 1 base 0080000000 mask FFC0000000 write-back
    [ 0.000000] 2 base 0100000000 mask FFC0000000 write-back
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] TOM2: 0000000140000000 aka 5120M
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xbffe0 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000f3c70-0x000f3c7f] mapped at [ffff8800000f3c70]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b32000, 0x01b32fff] PGTABLE
    [ 0.000000] BRK [0x01b33000, 0x01b33fff] PGTABLE
    [ 0.000000] BRK [0x01b34000, 0x01b34fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x13fe00000-0x13fffffff]
    [ 0.000000] [mem 0x13fe00000-0x13fffffff] page 2M
    [ 0.000000] BRK [0x01b35000, 0x01b35fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x13c000000-0x13fdfffff]
    [ 0.000000] [mem 0x13c000000-0x13fdfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x13bffffff]
    [ 0.000000] [mem 0x100000000-0x13bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0xbffdffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0xbfdfffff] page 2M
    [ 0.000000] [mem 0xbfe00000-0xbffdffff] page 4k
    [ 0.000000] RAMDISK: [mem 0x37a04000-0x37cf9fff]
    [ 0.000000] ACPI: RSDP 00000000000f7e70 00024 (v02 790FX )
    [ 0.000000] ACPI: XSDT 00000000bffe3080 00044 (v01 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: FACP 00000000bffeaa40 000F4 (v03 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: DSDT 00000000bffe3200 07822 (v01 790FX AWRDACPI 00001000 MSFT 03000000)
    [ 0.000000] ACPI: FACS 00000000bffe0000 00040
    [ 0.000000] ACPI: HPET 00000000bffeac00 00038 (v01 790FX AWRDACPI 42302E31 AWRD 00000098)
    [ 0.000000] ACPI: MCFG 00000000bffeac40 0003C (v01 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: APIC 00000000bffeab40 00084 (v01 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] Scanning NUMA topology in Northbridge 24
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000013fffffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
    [ 0.000000] NODE_DATA [mem 0x13fff8000-0x13fffcfff]
    [ 0.000000] [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013b600000-ffff88013f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x13fffffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0xbffdffff]
    [ 0.000000] node 0: [mem 0x100000000-0x13fffffff]
    [ 0.000000] On node 0 totalpages: 1048446
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 12224 pages used for memmap
    [ 0.000000] DMA32 zone: 782304 pages, LIFO batch:31
    [ 0.000000] Normal zone: 4096 pages used for memmap
    [ 0.000000] Normal zone: 262144 pages, LIFO batch:31
    [ 0.000000] Detected use of extended apic ids on hypertransport bus
    [ 0.000000] ACPI: PM-Timer IO Port: 0x4008
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbffe0000-0xbffe2fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbffe3000-0xbffeffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbfff0000-0xbfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xdfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
    [ 0.000000] e820: [mem 0xc0000000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88013fc00000 s86464 r8192 d24128 u524288
    [ 0.000000] pcpu-alloc: s86464 r8192 d24128 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1032041
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=f3bb4b9d-d9f1-4ef7-9180-07f1d4a00fc2 rw quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Node 0: aperture @ b4000000 size 32 MB
    [ 0.000000] Aperture pointing to e820 RAM. Ignoring.
    [ 0.000000] Your BIOS doesn't leave a aperture memory hole
    [ 0.000000] Please enable the IOMMU option in the BIOS setup
    [ 0.000000] This costs you 64 MB of RAM
    [ 0.000000] Mapping aperture over 65536 KB of RAM @ b4000000
    [ 0.000000] PM: Registered nosave memory: [mem 0xb4000000-0xb7ffffff]
    [ 0.000000] Memory: 3981312K/4193784K available (5115K kernel code, 806K rwdata, 1708K rodata, 1144K init, 1288K bss, 212472K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] NR_IRQS:8448 nr_irqs:712 16
    [ 0.000000] spurious 8259A interrupt: IRQ7.
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 16777216 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration failed
    [ 0.000000] tsc: Unable to calibrate against PIT
    [ 0.000000] tsc: using HPET reference calibration
    [ 0.000000] tsc: Detected 2700.249 MHz processor
    [ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
    [ 0.013338] Calibrating delay loop (skipped), value calculated using timer frequency.. 5402.51 BogoMIPS (lpj=9000830)
    [ 0.013342] pid_max: default: 32768 minimum: 301
    [ 0.013386] Security Framework initialized
    [ 0.013395] AppArmor: AppArmor disabled by boot time parameter
    [ 0.013396] Yama: becoming mindful.
    [ 0.013706] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.015721] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.017157] Mount-cache hash table entries: 256
    [ 0.017396] Initializing cgroup subsys memory
    [ 0.017414] Initializing cgroup subsys devices
    [ 0.017417] Initializing cgroup subsys freezer
    [ 0.017418] Initializing cgroup subsys net_cls
    [ 0.017420] Initializing cgroup subsys blkio
    [ 0.017442] tseg: 0000000000
    [ 0.017449] CPU: Physical Processor ID: 0
    [ 0.017450] CPU: Processor Core ID: 0
    [ 0.017452] mce: CPU supports 5 MCE banks
    [ 0.017458] LVT offset 0 assigned for vector 0xf9
    [ 0.017462] process: using AMD E400 aware idle routine
    [ 0.017464] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
    Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
    tlb_flushall_shift: 4
    [ 0.017546] Freeing SMP alternatives memory: 20K (ffffffff819e9000 - ffffffff819ee000)
    [ 0.018244] ACPI: Core revision 20130725
    [ 0.021196] ACPI: All ACPI Tables successfully acquired
    [ 0.023362] ftrace: allocating 20290 entries in 80 pages
    [ 0.034097] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.068081] smpboot: CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ (fam: 0f, model: 6b, stepping: 02)
    [ 0.069999] Performance Events: AMD PMU driver.
    [ 0.069999] ... version: 0
    [ 0.069999] ... bit width: 48
    [ 0.069999] ... generic registers: 4
    [ 0.069999] ... value mask: 0000ffffffffffff
    [ 0.069999] ... max period: 00007fffffffffff
    [ 0.069999] ... fixed-purpose events: 0
    [ 0.069999] ... event mask: 000000000000000f
    [ 0.083388] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.090068] smpboot: Booting Node 0, Processors # 1 OK
    [ 0.183403] Brought up 2 CPUs
    [ 0.183406] smpboot: Total of 2 processors activated (10805.89 BogoMIPS)
    [ 0.183927] devtmpfs: initialized
    [ 0.188111] PM: Registering ACPI NVS region [mem 0xbffe0000-0xbffe2fff] (12288 bytes)
    [ 0.188111] RTC time: 8:27:34, date: 12/02/13
    [ 0.188111] NET: Registered protocol family 16
    [ 0.188127] cpuidle: using governor ladder
    [ 0.188128] cpuidle: using governor menu
    [ 0.188133] node 0 link 0: io port [b000, ffff]
    [ 0.188135] TOM: 00000000c0000000 aka 3072M
    [ 0.188137] node 0 link 0: mmio [a0000, bffff]
    [ 0.188140] node 0 link 0: mmio [c0000000, dfffffff]
    [ 0.188142] node 0 link 0: mmio [f0000000, fe02ffff]
    [ 0.188144] node 0 link 0: mmio [e0000000, e04fffff]
    [ 0.188145] TOM2: 0000000140000000 aka 5120M
    [ 0.188148] bus: [bus 00-04] on node 0 link 0
    [ 0.188149] bus: 00 [io 0x0000-0xffff]
    [ 0.188151] bus: 00 [mem 0x000a0000-0x000bffff]
    [ 0.188152] bus: 00 [mem 0xc0000000-0xefffffff]
    [ 0.188153] bus: 00 [mem 0xf0000000-0xffffffff]
    [ 0.188155] bus: 00 [mem 0x140000000-0xfcffffffff]
    [ 0.188168] ACPI: bus type PCI registered
    [ 0.188170] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.188231] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.188234] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.199259] PCI: Using configuration type 1 for base access
    [ 0.199433] mtrr: your CPUs had inconsistent variable MTRR settings
    [ 0.199434] mtrr: probably your BIOS does not setup all CPUs.
    [ 0.199435] mtrr: corrected configuration.
    [ 0.200005] bio: create slab <bio-0> at 0
    [ 0.200048] ACPI: Added _OSI(Module Device)
    [ 0.200050] ACPI: Added _OSI(Processor Device)
    [ 0.200052] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.200053] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.200693] ACPI: EC: Look up EC in DSDT
    [ 0.201612] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.204741] ACPI: Interpreter enabled
    [ 0.204755] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
    [ 0.204760] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20130725/hwxface-571)
    [ 0.204770] ACPI: (supports S0 S1 S4 S5)
    [ 0.204771] ACPI: Using IOAPIC for interrupt routing
    [ 0.204841] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.204933] ACPI: No dock devices found.
    [ 0.217777] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.217785] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM
    [ 0.217787] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08)
    [ 0.218038] ACPI: \_SB_.PCI0.SYSR: can't evaluate _ADR (0x5)
    [ 0.218040] ACPI: \_SB_.PCI0.FDC0: can't evaluate _ADR (0x5)
    [ 0.218043] ACPI: \_SB_.PCI0.UAR1: can't evaluate _ADR (0x5)
    [ 0.218045] ACPI: \_SB_.PCI0.UAR2: can't evaluate _ADR (0x5)
    [ 0.218047] ACPI: \_SB_.PCI0.IRDA: can't evaluate _ADR (0x5)
    [ 0.218050] ACPI: \_SB_.PCI0.LPT1: can't evaluate _ADR (0x5)
    [ 0.218052] ACPI: \_SB_.PCI0.ECP1: can't evaluate _ADR (0x5)
    [ 0.218054] ACPI: \_SB_.PCI0.PS2M: can't evaluate _ADR (0x5)
    [ 0.218057] ACPI: \_SB_.PCI0.PS2K: can't evaluate _ADR (0x5)
    [ 0.218058] PCI host bridge to bus 0000:00
    [ 0.218061] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.218063] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.218065] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.218068] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.218069] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
    [ 0.218072] pci_bus 0000:00: root bus resource [mem 0xbfff0000-0xffffffff]
    [ 0.218083] pci 0000:00:00.0: [1002:5956] type 00 class 0x060000
    [ 0.218097] pci 0000:00:00.0: reg 0x1c: [mem 0xe0000000-0xffffffff 64bit]
    [ 0.218196] pci 0000:00:02.0: [1002:5978] type 01 class 0x060400
    [ 0.218233] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
    [ 0.218280] pci 0000:00:02.0: System wakeup disabled by ACPI
    [ 0.218322] pci 0000:00:06.0: [1002:597c] type 01 class 0x060400
    [ 0.218357] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
    [ 0.218402] pci 0000:00:06.0: System wakeup disabled by ACPI
    [ 0.218438] pci 0000:00:07.0: [1002:597d] type 01 class 0x060400
    [ 0.218473] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
    [ 0.218518] pci 0000:00:07.0: System wakeup disabled by ACPI
    [ 0.218573] pci 0000:00:12.0: [1002:4380] type 00 class 0x01018f
    [ 0.218594] pci 0000:00:12.0: reg 0x10: [io 0xff00-0xff07]
    [ 0.218605] pci 0000:00:12.0: reg 0x14: [io 0xfe00-0xfe03]
    [ 0.218616] pci 0000:00:12.0: reg 0x18: [io 0xfd00-0xfd07]
    [ 0.218626] pci 0000:00:12.0: reg 0x1c: [io 0xfc00-0xfc03]
    [ 0.218637] pci 0000:00:12.0: reg 0x20: [io 0xfb00-0xfb0f]
    [ 0.218648] pci 0000:00:12.0: reg 0x24: [mem 0xfe02f000-0xfe02f3ff]
    [ 0.218671] pci 0000:00:12.0: set SATA to AHCI mode
    [ 0.218780] pci 0000:00:13.0: [1002:4387] type 00 class 0x0c0310
    [ 0.218795] pci 0000:00:13.0: reg 0x10: [mem 0xfe02e000-0xfe02efff]
    [ 0.218895] pci 0000:00:13.0: System wakeup disabled by ACPI
    [ 0.218932] pci 0000:00:13.1: [1002:4388] type 00 class 0x0c0310
    [ 0.218947] pci 0000:00:13.1: reg 0x10: [mem 0xfe02d000-0xfe02dfff]
    [ 0.219048] pci 0000:00:13.1: System wakeup disabled by ACPI
    [ 0.219087] pci 0000:00:13.2: [1002:4389] type 00 class 0x0c0310
    [ 0.219102] pci 0000:00:13.2: reg 0x10: [mem 0xfe02c000-0xfe02cfff]
    [ 0.219203] pci 0000:00:13.2: System wakeup disabled by ACPI
    [ 0.219238] pci 0000:00:13.3: [1002:438a] type 00 class 0x0c0310
    [ 0.219253] pci 0000:00:13.3: reg 0x10: [mem 0xfe02b000-0xfe02bfff]
    [ 0.219354] pci 0000:00:13.3: System wakeup disabled by ACPI
    [ 0.219390] pci 0000:00:13.4: [1002:438b] type 00 class 0x0c0310
    [ 0.219405] pci 0000:00:13.4: reg 0x10: [mem 0xfe02a000-0xfe02afff]
    [ 0.219506] pci 0000:00:13.4: System wakeup disabled by ACPI
    [ 0.219554] pci 0000:00:13.5: [1002:4386] type 00 class 0x0c0320
    [ 0.219575] pci 0000:00:13.5: reg 0x10: [mem 0xfe029000-0xfe0290ff]
    [ 0.219665] pci 0000:00:13.5: supports D1 D2
    [ 0.219668] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
    [ 0.219716] pci 0000:00:13.5: System wakeup disabled by ACPI
    [ 0.219759] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
    [ 0.219783] pci 0000:00:14.0: reg 0x10: [io 0x0b00-0x0b0f]
    [ 0.219793] pci 0000:00:14.0: reg 0x14: [mem 0xfed00000-0xfed003ff]
    [ 0.219934] pci 0000:00:14.1: [1002:438c] type 00 class 0x01018a
    [ 0.219952] pci 0000:00:14.1: reg 0x10: [io 0x0000-0x0007]
    [ 0.219963] pci 0000:00:14.1: reg 0x14: [io 0x0000-0x0003]
    [ 0.219974] pci 0000:00:14.1: reg 0x18: [io 0x0000-0x0007]
    [ 0.219984] pci 0000:00:14.1: reg 0x1c: [io 0x0000-0x0003]
    [ 0.219995] pci 0000:00:14.1: reg 0x20: [io 0xf900-0xf90f]
    [ 0.220124] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
    [ 0.220151] pci 0000:00:14.2: reg 0x10: [mem 0xfe024000-0xfe027fff 64bit]
    [ 0.220234] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
    [ 0.220287] pci 0000:00:14.2: System wakeup disabled by ACPI
    [ 0.220322] pci 0000:00:14.3: [1002:438d] type 00 class 0x060100
    [ 0.220460] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
    [ 0.220536] pci 0000:00:14.4: System wakeup disabled by ACPI
    [ 0.220575] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
    [ 0.220645] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
    [ 0.220712] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
    [ 0.220779] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
    [ 0.220904] pci 0000:01:00.0: [10de:042c] type 00 class 0x030000
    [ 0.220917] pci 0000:01:00.0: reg 0x10: [mem 0xfa000000-0xfaffffff]
    [ 0.220929] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.220942] pci 0000:01:00.0: reg 0x1c: [mem 0xf8000000-0xf9ffffff 64bit]
    [ 0.220951] pci 0000:01:00.0: reg 0x24: [io 0xcf00-0xcf7f]
    [ 0.220959] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    [ 0.226682] pci 0000:00:02.0: PCI bridge to [bus 01]
    [ 0.226687] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
    [ 0.226690] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xfbffffff]
    [ 0.226694] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.226751] pci 0000:02:00.0: [11ab:4364] type 00 class 0x020000
    [ 0.226769] pci 0000:02:00.0: reg 0x10: [mem 0xfdcfc000-0xfdcfffff 64bit]
    [ 0.226780] pci 0000:02:00.0: reg 0x18: [io 0xee00-0xeeff]
    [ 0.226813] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    [ 0.226865] pci 0000:02:00.0: supports D1 D2
    [ 0.226868] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.233345] pci 0000:00:06.0: PCI bridge to [bus 02]
    [ 0.233349] pci 0000:00:06.0: bridge window [io 0xe000-0xefff]
    [ 0.233352] pci 0000:00:06.0: bridge window [mem 0xfdc00000-0xfdcfffff]
    [ 0.233356] pci 0000:00:06.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.233407] pci 0000:03:00.0: [197b:2363] type 00 class 0x010185
    [ 0.233479] pci 0000:03:00.0: reg 0x24: [mem 0xfdefe000-0xfdefffff]
    [ 0.233491] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
    [ 0.233534] pci 0000:03:00.0: PME# supported from D3hot
    [ 0.233590] pci 0000:03:00.1: [197b:2363] type 00 class 0x010185
    [ 0.233608] pci 0000:03:00.1: reg 0x10: [io 0xdf00-0xdf07]
    [ 0.233617] pci 0000:03:00.1: reg 0x14: [io 0xde00-0xde03]
    [ 0.233626] pci 0000:03:00.1: reg 0x18: [io 0xdd00-0xdd07]
    [ 0.233635] pci 0000:03:00.1: reg 0x1c: [io 0xdc00-0xdc03]
    [ 0.233644] pci 0000:03:00.1: reg 0x20: [io 0xdb00-0xdb0f]
    [ 0.233730] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.233738] pci 0000:00:07.0: PCI bridge to [bus 03]
    [ 0.233742] pci 0000:00:07.0: bridge window [io 0xd000-0xdfff]
    [ 0.233745] pci 0000:00:07.0: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.233749] pci 0000:00:07.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
    [ 0.233826] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode)
    [ 0.233831] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff]
    [ 0.233835] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff]
    [ 0.233840] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff pref]
    [ 0.233843] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.233845] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.233847] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.233850] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
    [ 0.233852] pci 0000:00:14.4: bridge window [mem 0xbfff0000-0xffffffff] (subtractive decode)
    [ 0.234022] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234071] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234118] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234165] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234213] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234260] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234308] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234355] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.235135] ACPI: Enabled 2 GPEs in block 00 to 1F
    [ 0.235141] ACPI: \_SB_.PCI0: notify handler is installed
    [ 0.235177] Found 1 acpi root devices
    [ 0.235262] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.235262] vgaarb: loaded
    [ 0.235262] vgaarb: bridge control possible 0000:01:00.0
    [ 0.235262] PCI: Using ACPI for IRQ routing
    [ 0.244778] PCI: pci_cache_line_size set to 64 bytes
    [ 0.244786] pci 0000:00:00.0: address space collision: [mem 0xe0000000-0xffffffff 64bit] conflicts with PCI Bus 0000:01 [mem 0xf8000000-0xfbffffff]
    [ 0.244846] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
    [ 0.244848] e820: reserve RAM buffer [mem 0xbffe0000-0xbfffffff]
    [ 0.244956] NetLabel: Initializing
    [ 0.244957] NetLabel: domain hash size = 128
    [ 0.244959] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.244971] NetLabel: unlabeled traffic allowed by default
    [ 0.244995] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    [ 0.244999] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
    [ 0.246697] Switched to clocksource hpet
    [ 0.251917] pnp: PnP ACPI init
    [ 0.251938] ACPI: bus type PNP registered
    [ 0.252120] pnp 00:00: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.252151] pnp 00:00: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
    [ 0.252156] pnp 00:00: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:02:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
    [ 0.252160] pnp 00:00: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref]
    [ 0.252195] system 00:00: [io 0x4100-0x411f] has been reserved
    [ 0.252199] system 00:00: [io 0x0228-0x022f] has been reserved
    [ 0.252201] system 00:00: [io 0x040b] has been reserved
    [ 0.252204] system 00:00: [io 0x04d6] has been reserved
    [ 0.252206] system 00:00: [io 0x0c00-0x0c01] has been reserved
    [ 0.252209] system 00:00: [io 0x0c14] has been reserved
    [ 0.252211] system 00:00: [io 0x0c50-0x0c52] has been reserved
    [ 0.252214] system 00:00: [io 0x0c6c-0x0c6d] has been reserved
    [ 0.252216] system 00:00: [io 0x0c6f] has been reserved
    [ 0.252219] system 00:00: [io 0x0cd0-0x0cd1] has been reserved
    [ 0.252221] system 00:00: [io 0x0cd2-0x0cd3] has been reserved
    [ 0.252224] system 00:00: [io 0x0cd4-0x0cdf] has been reserved
    [ 0.252226] system 00:00: [io 0x4000-0x40fe] could not be reserved
    [ 0.252229] system 00:00: [io 0x4210-0x4217] has been reserved
    [ 0.252231] system 00:00: [io 0x0b10-0x0b1f] has been reserved
    [ 0.252235] system 00:00: [mem 0xfee00400-0xfee00fff window] has been reserved
    [ 0.252239] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.252336] pnp 00:01: [dma 4]
    [ 0.252360] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.252442] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.252487] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.252510] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.252544] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.252614] system 00:06: [io 0x04d0-0x04d1] has been reserved
    [ 0.252617] system 00:06: [io 0x0f40-0x0f45] has been reserved
    [ 0.252620] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.252767] pnp 00:07: [dma 2]
    [ 0.252808] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
    [ 0.253041] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.253372] pnp 00:09: Plug and Play ACPI device, IDs PNP0510 (active)
    [ 0.253612] pnp 00:0a: Plug and Play ACPI device, IDs PNP0400 (active)
    [ 0.253805] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.253859] pnp 00:0c: disabling [mem 0x000f0000-0x000fffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253862] pnp 00:0c: disabling [mem 0x00000000-0x001fffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253865] pnp 00:0c: disabling [mem 0x00000000-0x0009ffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253868] pnp 00:0c: disabling [mem 0x00100000-0xbffdffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253878] pnp 00:0c: disabling [mem 0xfed00000-0xfed000ff] because it overlaps 0000:00:14.0 BAR 1 [mem 0xfed00000-0xfed003ff]
    [ 0.253911] system 00:0c: [mem 0xbffe0000-0xbfffffff] could not be reserved
    [ 0.253914] system 00:0c: [mem 0xffff0000-0xffffffff] has been reserved
    [ 0.253917] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.253919] system 00:0c: [mem 0xfee00000-0xfee00fff] could not be reserved
    [ 0.253922] system 00:0c: [mem 0xfff80000-0xfffeffff] has been reserved
    [ 0.253924] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.253938] pnp: PnP ACPI: found 13 devices
    [ 0.253939] ACPI: bus type PNP unregistered
    [ 0.261111] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb01ffff pref]
    [ 0.261115] pci 0000:00:02.0: PCI bridge to [bus 01]
    [ 0.261118] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
    [ 0.261121] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xfbffffff]
    [ 0.261124] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.261129] pci 0000:02:00.0: BAR 6: assigned [mem 0xfdf00000-0xfdf1ffff pref]
    [ 0.261131] pci 0000:00:06.0: PCI bridge to [bus 02]
    [ 0.261133] pci 0000:00:06.0: bridge window [io 0xe000-0xefff]
    [ 0.261136] pci 0000:00:06.0: bridge window [mem 0xfdc00000-0xfdcfffff]
    [ 0.261139] pci 0000:00:06.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.261144] pci 0000:03:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd0ffff pref]
    [ 0.261146] pci 0000:00:07.0: PCI bridge to [bus 03]
    [ 0.261148] pci 0000:00:07.0: bridge window [io 0xd000-0xdfff]
    [ 0.261151] pci 0000:00:07.0: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.261154] pci 0000:00:07.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
    [ 0.261158] pci 0000:00:14.4: PCI bridge to [bus 04]
    [ 0.261161] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff]
    [ 0.261166] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff]
    [ 0.261171] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff pref]
    [ 0.261178] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.261180] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.261182] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.261184] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
    [ 0.261186] pci_bus 0000:00: resource 8 [mem 0xbfff0000-0xffffffff]
    [ 0.261188] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
    [ 0.261190] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff]
    [ 0.261192] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.261195] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
    [ 0.261197] pci_bus 0000:02: resource 1 [mem 0xfdc00000-0xfdcfffff]
    [ 0.261199] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.261201] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
    [ 0.261203] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
    [ 0.261205] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
    [ 0.261207] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff]
    [ 0.261209] pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
    [ 0.261211] pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff pref]
    [ 0.261213] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
    [ 0.261215] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
    [ 0.261217] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.261219] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
    [ 0.261221] pci_bus 0000:04: resource 8 [mem 0xbfff0000-0xffffffff]
    [ 0.261266] NET: Registered protocol family 2
    [ 0.261475] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.261731] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.261986] TCP: Hash tables configured (established 32768 bind 32768)
    [ 0.262046] TCP: reno registered
    [ 0.262057] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.262089] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.262209] NET: Registered protocol family 1
    [ 0.616902] pci 0000:01:00.0: Boot video device
    [ 0.616913] PCI: CLS 32 bytes, default 64
    [ 0.616966] Unpacking initramfs...
    [ 0.676909] Freeing initrd memory: 3032K (ffff880037a04000 - ffff880037cfa000)
    [ 0.677630] PCI-DMA: Disabling AGP.
    [ 0.677710] PCI-DMA: aperture base @ b4000000 size 65536 KB
    [ 0.677712] PCI-DMA: using GART IOMMU.
    [ 0.677715] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
    [ 0.682349] Scanning for low memory corruption every 60 seconds
    [ 0.682695] audit: initializing netlink socket (disabled)
    [ 0.682709] type=2000 audit(1385972853.679:1): initialized
    [ 0.693650] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.695128] zbud: loaded
    [ 0.695281] VFS: Disk quotas dquot_6.5.2
    [ 0.695335] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.695554] msgmni has been set to 7910
    [ 0.695944] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.695993] io scheduler noop registered
    [ 0.695995] io scheduler deadline registered
    [ 0.696025] io scheduler cfq registered (default)
    [ 0.696145] pcieport 0000:00:02.0: irq 40 for MSI/MSI-X
    [ 0.696229] pcieport 0000:00:06.0: irq 41 for MSI/MSI-X
    [ 0.696299] pcieport 0000:00:07.0: irq 42 for MSI/MSI-X
    [ 0.696374] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.696391] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.696444] vesafb: mode is 640x480x32, linelength=2560, pages=0
    [ 0.696445] vesafb: scrolling: redraw
    [ 0.696447] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.696504] vesafb: framebuffer at 0xf9000000, mapped to 0xffffc90010800000, using 1216k, total 1216k
    [ 0.702849] Console: switching to colour frame buffer device 80x30
    [ 0.709096] fb0: VESA VGA frame buffer device
    [ 0.709135] GHES: HEST is not enabled!
    [ 0.709196] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.729882] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
    [ 0.750605] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
    [ 0.750958] Linux agpgart interface v0.103
    [ 0.751006] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    [ 0.751007] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
    [ 0.751728] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.751860] mousedev: PS/2 mouse device common for all mice
    [ 0.751927] rtc_cmos 00:03: RTC can wake from S4
    [ 0.752067] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 0.752106] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 0.752187] drop_monitor: Initializing network drop monitor service
    [ 0.752254] TCP: cubic registered
    [ 0.752361] NET: Registered protocol family 10
    [ 0.752553] NET: Registered protocol family 17
    [ 0.752565] Key type dns_resolver registered
    [ 0.752847] registered taskstats version 1
    [ 0.753423] Magic number: 9:957:471
    [ 0.753514] rtc_cmos 00:03: setting system clock to 2013-12-02 08:27:34 UTC (1385972854)
    [ 0.753559] PM: Hibernation image not present or could not be loaded.
    [ 0.755068] Freeing unused kernel memory: 1144K (ffffffff818cb000 - ffffffff819e9000)
    [ 0.755072] Write protecting the kernel read-only data: 8192k
    [ 0.758083] Freeing unused kernel memory: 1016K (ffff880001502000 - ffff880001600000)
    [ 0.759079] Freeing unused kernel memory: 340K (ffff8800017ab000 - ffff880001800000)
    [ 0.769771] systemd-udevd[47]: starting version 208
    [ 0.794492] Floppy drive(s): fd0 is 1.44M
    [ 0.803163] ACPI: bus type USB registered
    [ 0.803196] usbcore: registered new interface driver usbfs
    [ 0.803207] usbcore: registered new interface driver hub
    [ 0.804032] usbcore: registered new device driver usb
    [ 0.804145] SCSI subsystem initialized
    [ 0.804718] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.805817] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.805956] ohci-pci: OHCI PCI platform driver
    [ 0.806132] ohci-pci 0000:00:13.0: OHCI PCI host controller
    [ 0.806149] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 1
    [ 0.806197] ohci-pci 0000:00:13.0: irq 16, io mem 0xfe02e000
    [ 0.808453] ehci-pci: EHCI PCI platform driver
    [ 0.810692] FDC 0 is a post-1991 82077
    [ 0.810859] libata version 3.00 loaded.
    [ 0.811723] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
    [ 0.811823] pata_jmicron 0000:03:00.1: setting latency timer to 64
    [ 0.812133] scsi0 : pata_jmicron
    [ 0.812212] scsi1 : pata_jmicron
    [ 0.812251] ata1: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16
    [ 0.812253] ata2: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16
    [ 0.860877] hub 1-0:1.0: USB hub found
    [ 0.860890] hub 1-0:1.0: 2 ports detected
    [ 0.861158] ohci-pci 0000:00:13.1: OHCI PCI host controller
    [ 0.861166] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 2
    [ 0.861205] ohci-pci 0000:00:13.1: irq 17, io mem 0xfe02d000
    [ 0.917507] hub 2-0:1.0: USB hub found
    [ 0.917518] hub 2-0:1.0: 2 ports detected
    [ 0.917709] ohci-pci 0000:00:13.2: OHCI PCI host controller
    [ 0.917715] ohci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3
    [ 0.917744] ohci-pci 0000:00:13.2: irq 18, io mem 0xfe02c000
    [ 0.974160] hub 3-0:1.0: USB hub found
    [ 0.974171] hub 3-0:1.0: 2 ports detected
    [ 0.974357] ohci-pci 0000:00:13.3: OHCI PCI host controller
    [ 0.974364] ohci-pci 0000:00:13.3: new USB bus registered, assigned bus number 4
    [ 0.974382] ohci-pci 0000:00:13.3: irq 17, io mem 0xfe02b000
    [ 1.030833] hub 4-0:1.0: USB hub found
    [ 1.030843] hub 4-0:1.0: 2 ports detected
    [ 1.031028] ohci-pci 0000:00:13.4: OHCI PCI host controller
    [ 1.031034] ohci-pci 0000:00:13.4: new USB bus registered, assigned bus number 5
    [ 1.031049] ohci-pci 0000:00:13.4: irq 18, io mem 0xfe02a000
    [ 1.087499] hub 5-0:1.0: USB hub found
    [ 1.087509] hub 5-0:1.0: 2 ports detected
    [ 1.190024] usb 1-1: new low-speed USB device number 2 using ohci-pci
    [ 1.483353] usb 1-2: new low-speed USB device number 3 using ohci-pci
    [ 1.643840] usb 1-1: USB disconnect, device number 2
    [ 1.644033] usb 1-2: USB disconnect, device number 3
    [ 1.760279] ehci-pci 0000:00:13.5: EHCI Host Controller
    [ 1.760288] ehci-pci 0000:00:13.5: new USB bus registered, assigned bus number 6
    [ 1.760297] ehci-pci 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
    [ 1.760313] ehci-pci 0000:00:13.5: debug port 1
    [ 1.760381] ehci-pci 0000:00:13.5: irq 19, io mem 0xfe029000
    [ 1.770022] ehci-pci 0000:00:13.5: USB 2.0 started, EHCI 1.00
    [ 1.770182] hub 6-0:1.0: USB hub found
    [ 1.770191] hub 6-0:1.0: 10 ports detected
    [ 1.826731] hub 1-0:1.0: USB hub found
    [ 1.826742] hub 1-0:1.0: 2 ports detected
    [ 1.828066] hidraw: raw HID events driver (C) Jiri Kosina
    [ 1.828580] usbcore: registered new interface driver usbhid
    [ 1.828583] usbhid: USB HID core driver
    [ 1.883417] hub 2-0:1.0: USB hub found
    [ 1.883431] hub 2-0:1.0: 2 ports detected
    [ 1.940057] hub 3-0:1.0: USB hub found
    [ 1.940067] hub 3-0:1.0: 2 ports detected
    [ 1.996722] hub 4-0:1.0: USB hub found
    [ 1.996732] hub 4-0:1.0: 2 ports detected
    [ 2.053388] hub 5-0:1.0: USB hub found
    [ 2.053398] hub 5-0:1.0: 2 ports detected
    [ 2.053683] ahci 0000:00:12.0: version 3.0
    [ 2.053835] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
    [ 2.053933] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    [ 2.053937] ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio ccc
    [ 2.054699] scsi2 : ahci
    [ 2.054775] scsi3 : ahci
    [ 2.054850] scsi4 : ahci
    [ 2.054920] scsi5 : ahci
    [ 2.054967] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
    [ 2.054971] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
    [ 2.054974] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
    [ 2.054977] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
    [ 2.056192] scsi6 : pata_atiixp
    [ 2.056251] scsi7 : pata_atiixp
    [ 2.056292] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
    [ 2.056294] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
    [ 2.066728] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
    [ 2.066733] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
    [ 2.067129] scsi8 : ahci
    [ 2.067200] scsi9 : ahci
    [ 2.067257] ata9: SATA max UDMA/133 abar m8192@0xfdefe000 port 0xfdefe100 irq 19
    [ 2.067260] ata10: SATA max UDMA/133 abar m8192@0xfdefe000 port 0xfdefe180 irq 19
    [ 2.213828] ata7.00: ATAPI: HL-DT-ST RW/DVD GCC-4481B, 1.04, max UDMA/33
    [ 2.227109] ata7.00: configured for UDMA/33
    [ 2.373413] ata6: SATA link down (SStatus 0 SControl 300)
    [ 2.386722] ata9: SATA link down (SStatus 0 SControl 300)
    [ 2.386768] ata10: SATA link down (SStatus 0 SControl 300)
    [ 2.540027] ata3: softreset failed (device not ready)
    [ 2.540185] ata3: applying PMP SRST workaround and retrying
    [ 2.540217] ata5: softreset failed (device not ready)
    [ 2.540381] ata5: applying PMP SRST workaround and retrying
    [ 2.540408] ata4: softreset failed (device not ready)
    [ 2.540563] ata4: applying PMP SRST workaround and retrying
    [ 2.566689] usb 1-1: new low-speed USB device number 4 using ohci-pci
    [ 2.706711] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.706750] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 2.706786] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 2.707572] ata3.00: ATA-7: ST3200826AS, 3.03, max UDMA/133
    [ 2.707575] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32)
    [ 2.707578] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.708066] ata4.00: ATA-8: TOSHIBA DT01ACA200, MX4OABB0, max UDMA/133
    [ 2.708068] ata4.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 2.708070] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.708443] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.708445] ata3.00: configured for UDMA/133
    [ 2.708626] scsi 2:0:0:0: Direct-Access ATA ST3200826AS 3.03 PQ: 0 ANSI: 5
    [ 2.709433] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.709436] ata4.00: configured for UDMA/133
    [ 2.709543] scsi 3:0:0:0: Direct-Access ATA TOSHIBA DT01ACA2 MX4O PQ: 0 ANSI: 5
    [ 2.709897] sd 2:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
    [ 2.709940] sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
    [ 2.709942] sd 3:0:0:0: [sdb] 4096-byte physical blocks
    [ 2.710054] sd 2:0:0:0: [sda] Write Protect is off
    [ 2.710057] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.710081] sd 3:0:0:0: [sdb] Write Protect is off
    [ 2.710083] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    [ 2.710108] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.710131] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.713184] ata5.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
    [ 2.713188] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
    [ 2.713191] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.716937] sdb: sdb1
    [ 2.717244] sd 3:0:0:0: [sdb] Attached SCSI disk
    [ 2.719680] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.719683] ata5.00: configured for UDMA/133
    [ 2.719828] scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
    [ 2.720076] sd 4:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    [ 2.720133] sd 4:0:0:0: [sdc] Write Protect is off
    [ 2.720136] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
    [ 2.720160] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.721044] scsi 6:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4481B 1.04 PQ: 0 ANSI: 5
    [ 2.723354] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
    [ 2.723359] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.723609] sr 6:0:0:0: Attached scsi CD-ROM sr0
    [ 2.726375] ata5.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
    [ 2.726661] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 2.726858] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 2.727057] ata5.00: failed command: READ FPDMA QUEUED
    [ 2.727277] ata5.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
    res 40/00:04:00:00:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 2.728116] ata5.00: status: { DRDY }
    [ 2.728231] ata5: hard resetting link
    [ 2.736521] sda: sda1 sda2 < sda5 >
    [ 2.736973] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 2.744047] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:13.0/usb1/1-1/1-1:1.0/input/input1
    [ 2.744380] hid-generic 0003:0518:0001.0001: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:13.0-1/input0
    [ 2.744812] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:13.0/usb1/1-1/1-1:1.1/input/input2
    [ 2.745088] hid-generic 0003:0518:0001.0002: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:13.0-1/input1
    [ 2.990025] usb 1-2: new low-speed USB device number 5 using ohci-pci
    [ 3.156230] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:13.0/usb1/1-2/1-2:1.0/input/input3
    [ 3.156413] hid-generic 0003:045E:0040.0003: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.0-2/input0
    [ 3.213356] ata5: softreset failed (device not ready)
    [ 3.213519] ata5: applying PMP SRST workaround and retrying
    [ 3.380031] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 3.386448] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 3.392796] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x100)
    [ 3.392798] ata5.00: revalidation failed (errno=-5)
    [ 8.380028] ata5: hard resetting link
    [ 8.866697] ata5: softreset failed (device not ready)
    [ 8.866861] ata5: applying PMP SRST workaround and retrying
    [ 9.033366] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 9.039792] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 9.046258] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 9.046260] ata5.00: configured for UDMA/133
    [ 9.046276] ata5: EH complete
    [ 9.052053] sdc: sdc1
    [ 9.052397] sdc: detected capacity change from 0 to 1000204886016
    [ 9.052488] sd 4:0:0:0: [sdc] Attached SCSI disk
    [ 9.102207] ata5.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
    [ 9.102441] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 9.102622] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 9.102820] ata5.00: failed command: READ FPDMA QUEUED
    [ 9.102979] ata5.00: cmd 60/08:00:a8:6c:70/00:00:74:00:00/40 tag 0 ncq 4096 in
    res 40/00:04:a8:6c:70/00:00:74:00:00/40 Emask 0x50 (ATA bus error)
    [ 9.103442] ata5.00: status: { DRDY }
    [ 9.103556] ata5: hard resetting link
    [ 9.590022] ata5: softreset failed (device not ready)
    [ 9.590182] ata5: applying PMP SRST workaround and retrying
    [ 9.756697] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 9.763109] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 9.769456] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x100)
    [ 9.769458] ata5.00: revalidation failed (errno=-5)
    [ 9.969270] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    [ 14.756687] ata5: hard resetting link
    [ 15.243350] ata5: softreset failed (device not ready)
    [ 15.247493] ata5: applying PMP SRST workaround and retrying
    [ 15.413369] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 15.419789] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 15.426253] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 15.426255] ata5.00: configured for UDMA/133
    [ 15.426271] ata5: EH complete
    [ 15.457509] ata5.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
    [ 15.466153] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 15.470623] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 15.475077] ata5.00: failed command: READ FPDMA QUEUED
    [ 15.479477] ata5.00: cmd 60/08:00:f8:69:70/00:00:74:00:00/40 tag 0 ncq 4096 in
    res 40/00:04:f8:69:70/00:00:74:00:00/40 Emask 0x50 (ATA bus error)
    [ 15.497016] ata5.00: status: { DRDY }
    [ 15.501349] ata5: hard resetting link
    [ 15.986684] ata5: softreset failed (device not ready)
    [ 15.990999] ata5: applying PMP SRST workaround and retrying
    [ 16.156695] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 16.163100] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.169558] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.169560] ata5.00: configured for UDMA/133
    [ 16.169567] ata5: EH complete
    [ 16.230439] ata5: limiting SATA link speed to 1.5 Gbps
    [ 16.230445] ata5.00: exception Emask 0x50 SAct 0x1c SErr 0x680900 action 0x6 frozen
    [ 16.239215] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 16.243744] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 16.248330] ata5.00: failed command: READ FPDMA QUEUED
    [ 16.252861] ata5.00: cmd 60/38:10:40:00:00/00:00:00:00:00/40 tag 2 ncq 28672 in
    res 40/00:24:78:01:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 16.270799] ata5.00: status: { DRDY }
    [ 16.275275] ata5.00: failed command: READ FPDMA QUEUED
    [ 16.279713] ata5.00: cmd 60/f8:18:80:00:00/00:00:00:00:00/40 tag 3 ncq 126976 in
    res 40/00:24:78:01:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 16.297504] ata5.00: status: { DRDY }
    [ 16.302022] ata5.00: failed command: READ FPDMA QUEUED
    [ 16.306524] ata5.00: cmd 60/88:20:78:01:00/00:00:00:00:00/40 tag 4 ncq 69632 in
    res 40/00:24:78:01:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 16.324306] ata5.00: status: { DRDY }
    [ 16.328707] ata5: hard resetting link
    [ 16.813352] ata5: softreset failed (device not ready)
    [ 16.817758] ata5: applying PMP SRST workaround and retrying
    [ 16.983368] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 16.989783] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.996261] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.996263] ata5.00: configured for UDMA/133
    [ 16.996279] ata5: EH complete
    [ 17.672607] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
    [ 17.677851] systemd[1]: Set hostname to <ROTATION-STATION>.
    [ 18.109971] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 18.109984] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 18.110330] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 18.110410] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 18.110428] systemd[1]: Expecting device sys-subsystem-net-devices-enp2s0.device...
    [ 18.110443] systemd[1]: Starting Remote File Systems.
    [ 18.110456] systemd[1]: Reached target Remote File Systems.
    [ 18.110468] systemd[1]: Starting Delayed Shutdown Socket.
    [ 18.110505] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 18.110517] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 18.110546] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 18.110558] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 18.110583] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 18.110595] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 18.110624] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 18.110638] systemd[1]: Starting Encrypted Volumes.
    [ 18.110651] systemd[1]: Reached target Encrypted Volumes.
    [ 18.110664] systemd[1]: Starting Journal Socket.
    [ 18.110711] systemd[1]: Listening on Journal Socket.
    [ 18.110728] systemd[1]: Starting Setup Virtual Console...
    [ 18.138476] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 18.139007] systemd[1]: Mounting Huge Pages File System...
    [ 18.139550] systemd[1]: Starting Journal Service...
    [ 18.140217] systemd[1]: Started Journal Service.
    [ 18.406055] systemd-journald[127]: Vacuuming done, freed 0 bytes
    [ 18.685974] EXT4-fs (sda1): re-mounted. Opts: data=ordered
    [ 18.806623] systemd-udevd[155]: starting version 208
    [ 19.322248] parport_pc 00:0a: reported by Plug and Play ACPI
    [ 19.322309] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    [ 19.331550] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
    [ 19.331559] ACPI: Power Button [PWRB]
    [ 19.331882] ACPI: Fan [FAN] (on)
    [ 19.332660] ACPI: [Package] has zero elements (ffff8800bf306e80)
    [ 19.337757] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
    [ 19.337764] ACPI: Power Button [PWRF]
    [ 19.337878] ACPI: Invalid passive threshold
    [ 19.338149] thermal LNXTHERM:00: registered as thermal_zone0
    [ 19.338151] ACPI: Thermal Zone [THRM] (40 C)
    [ 19.387889] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 19.388553] wmi: Mapper loaded
    [ 19.549117] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \SOR2 1 (20130725/utaddress-251)
    [ 19.549126] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \SOR1 2 (20130725/utaddress-251)
    [ 19.549131] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 19.717185] MCE: In-kernel MCE decoding enabled.
    [ 19.733875] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
    [ 19.746781] input: PC Speaker as /devices/platform/pcspkr/input/input6
    [ 19.780737] [drm] Initialized drm 1.1.0 20060810
    [ 19.801750] EDAC MC: Ver: 3.0.0
    [ 19.808239] sky2: driver version 1.30
    [ 19.808388] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 5
    [ 19.808451] sky2 0000:02:00.0: irq 43 for MSI/MSI-X
    [ 19.808698] sky2 0000:02:00.0 eth0: addr 00:30:18:a6:19:e3
    [ 19.835294] snd_hda_intel 0000:00:14.2: irq 44 for MSI/MSI-X
    [ 19.870517] AMD64 EDAC driver v3.4.0
    [ 19.895226] microcode: AMD CPU family 0xf not supported
    [ 19.929703] systemd-udevd[156]: renamed network interface eth0 to enp2s0
    [ 20.021077] kvm: Nested Virtualization enabled
    [ 20.073770] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
    [Firmware Bug]: powernow-k8: First, make sure Cool'N'Quiet is enabled in the BIOS.
    [Firmware Bug]: powernow-k8: If that doesn't help, try upgrading your BIOS.
    [ 20.088804] checking generic (f9000000 130000) vs hw (d0000000 10000000)
    [ 20.088805] checking generic (f9000000 130000) vs hw (f8000000 2000000)
    [ 20.088806] fb: conflicting fb hw usage nouveaufb vs VESA VGA - removing generic driver
    [ 20.100569] Console: switching to colour dummy device 80x25
    [ 20.101154] [drm] hdmi device not found 1 0 1
    [ 20.101224] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x086c00a2
    [ 20.101227] nouveau [ DEVICE][0000:01:00.0] Chipset: G86 (NV86)
    [ 20.101229] nouveau [ DEVICE][0000:01:00.0] Family : NV50
    [ 20.101830] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
    [ 20.113952] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
    [Firmware Bug]: powernow-k8: First, make sure Cool'N'Quiet is enabled in the BIOS.
    [Firmware Bug]: powernow-k8: If that doesn't help, try upgrading your BIOS.
    [ 20.157989] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
    [ 20.158048] sp5100_tco: PCI Revision ID: 0x13
    [ 20.158077] sp5100_tco: failed to find MMIO address, giving up.
    [ 20.162297] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
    [ 20.162300] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
    [ 20.162421] nouveau [ VBIOS][0000:01:00.0] BIT signature found
    [ 20.162424] nouveau [ VBIOS][0000:01:00.0] version 60.86.65.00.51
    [ 20.182582] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
    [ 20.182585] nouveau [ PFB][0000:01:00.0] RAM size: 512 MiB
    [ 20.182586] nouveau [ PFB][0000:01:00.0] ZCOMP: 1292 tags
    [ 20.204429] nouveau [ PTHERM][0000:01:00.0] FAN control: none / external
    [ 20.204439] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
    [ 20.204442] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
    [ 20.204613] [TTM] Zone kernel: Available graphics memory: 2026408 kiB
    [ 20.204615] [TTM] Initializing pool allocator
    [ 20.204619] [TTM] Initializing DMA pool allocator
    [ 20.204630] nouveau [ DRM] VRAM: 512 MiB
    [ 20.204632] nouveau [ DRM] GART: 1048576 MiB
    [ 20.204636] nouveau [ DRM] TMDS table version 2.0
    [ 20.204638] nouveau [ DRM] DCB version 4.0
    [ 20.204641] nouveau [ DRM] DCB outp 00: 01000302 00020030
    [ 20.204644] nouveau [ DRM] DCB outp 01: 02000300 00020028
    [ 20.204646] nouveau [ DRM] DCB outp 02: 02011312 00020030
    [ 20.204648] nouveau [ DRM] DCB outp 03: 04011310 00c0c028
    [ 20.204650] nouveau [ DRM] DCB outp 04: 010223f1 00c0c080
    [ 20.204652] nouveau [ DRM] DCB conn 00: 2030
    [ 20.204655] nouveau [ DRM] DCB conn 01: 1130
    [ 20.204657] nouveau [ DRM] DCB conn 02: 0210
    [ 20.204659] nouveau [ DRM] DCB conn 03: 0211
    [ 20.204660] nouveau [ DRM] DCB conn 04: 0213
    [ 20.210863] nouveau W[ DRM] failed to create encoder 0/1/0: -19
    [ 20.210865] nouveau W[ DRM] TV-1 has no encoders, removing
    [ 20.210895] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 20.210897] [drm] No driver support for vblank timestamp query.
    [ 20.211027] nouveau [ DRM] 1 available performance level(s)
    [ 20.211031] nouveau [ DRM] 0: core 500MHz shader 1250MHz memory 400MHz fanspeed 100%
    [ 20.211033] nouveau [ DRM] c: core 459MHz shader 918MHz memory 399MHz voltage 1320mV
    [ 20.214375] ppdev: user-space parallel port driver
    [ 20.218673] nouveau [ DRM] MM: using CRYPT for buffer copies
    [ 20.270146] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input14
    [ 20.276729] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
    [ 20.276801] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
    [ 20.276871] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
    [ 20.276937] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
    [ 20.277003] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
    [ 20.277072] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
    [ 20.277146] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
    [ 20.288590] nouveau [ DRM] allocated 1680x1050 fb: 0x70000, bo ffff88013974c000
    [ 20.288622] EDAC amd64: DRAM ECC disabled.
    [ 20.288629] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
    Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
    (Note that use of the override may cause unknown side effects.)
    [ 20.288675] fbcon: nouveaufb (fb0) is primary device
    [ 20.376049] Console: switching to colour frame buffer device 128x48
    [ 20.376338] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
    [ 20.376340] nouveau 0000:01:00.0: registered panic notifier
    [ 20.376346] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
    [ 20.568688] Adding 2500432k swap on /dev/sda5. Priority:-1 extents:1 across:2500432k FS
    [ 20.811563] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 20.855298] systemd-journald[127]: Received request to flush runtime journal from PID 1
    [ 22.153827] sky2 0000:02:00.0 enp2s0: enabling interface
    [ 22.153887] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
    [ 24.883373] sky2 0000:02:00.0 enp2s0: Link is up at 1000 Mbps, full duplex, flow control both
    [ 24.883402] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
    [ 102.400031] ata4.00: exception Emask 0x0 SAct 0x2 SErr 0x0 action 0x6 frozen
    [ 102.400038] ata4.00: failed command: READ FPDMA QUEUED
    [ 102.400044] ata4.00: cmd 60/c8:08:40:0e:00/00:00:94:00:00/40 tag 1 ncq 102400 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 102.400046] ata4.00: status: { DRDY }
    [ 102.400051] ata4: hard resetting link
    [ 102.933349] ata4: softreset failed (device not ready)
    [ 102.933356] ata4: applying PMP SRST workaround and retrying
    [ 103.100029] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 103.101156] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 103.102323] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 103.102326] ata4.00: configured for UDMA/133
    [ 103.102330] ata4.00: device reported invalid CHS sector 0
    [ 103.102340] sd 3:0:0:0: [sdb]
    [ 103.102342] Result: hostbyte=0x00 driverbyte=0x08
    [ 103.102344] sd 3:0:0:0: [sdb]
    [ 103.102345] Sense Key : 0xb [current] [descriptor]
    [ 103.102348] Descriptor sense data with sense descriptors (in hex):
    [ 103.102349] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 103.102355] 00 00 00 00
    [ 103.102358] sd 3:0:0:0: [sdb]
    [ 103.102359] ASC=0x0 ASCQ=0x0
    [ 103.102361] sd 3:0:0:0: [sdb] CDB:
    [ 103.102363] cdb[0]=0x28: 28 00 94 00 0e 40 00 00 c8 00
    [ 103.102369] end_request: I/O error, dev sdb, sector 2483031616
    [ 103.102415] ata4: EH complete
    [ 103.157724] EXT4-fs error (device sdb1): __ext4_get_inode_loc:3917: inode #77597314: block 310378696: comm Plex Media Serv: unable to read itable block
    [ 133.386698] ata4.00: exception Emask 0x0 SAct 0x1ffffe0 SErr 0x0 action 0x6 frozen
    [ 133.386706] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386711] ata4.00: cmd 60/08:28:70:0e:00/00:00:94:00:00/40 tag 5 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386714] ata4.00: status: { DRDY }
    [ 133.386716] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386721] ata4.00: cmd 60/08:30:78:0e:00/00:00:94:00:00/40 tag 6 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386723] ata4.00: status: { DRDY }
    [ 133.386725] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386729] ata4.00: cmd 60/08:38:80:0e:00/00:00:94:00:00/40 tag 7 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386731] ata4.00: status: { DRDY }
    [ 133.386733] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386738] ata4.00: cmd 60/08:40:88:0e:00/00:00:94:00:00/40 tag 8 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386740] ata4.00: status: { DRDY }
    [ 133.386742] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386746] ata4.00: cmd 60/08:48:90:0e:00/00:00:94:00:00/40 tag 9 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386748] ata4.00: status: { DRDY }
    [ 133.386750] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386755] ata4.00: cmd 60/08:50:98:0e:00/00:00:94:00:00/40 tag 10 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386757] ata4.00: status: { DRDY }
    [ 133.386759] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386763] ata4.00: cmd 60/08:58:a0:0e:00/00:00:94:00:00/40 tag 11 ncq 4096 in
    res 40/00:00:00:00:00/00:00:

    I should preface this with I'm not a Linux noob, but I am no expert either (I get by).  Also I hope this is the right forum to post in. So after I updated about a week ago I start seeing errors at boot.  Never could quite see exactly what they were so today I logged dmesg to a text file.  I should also say the only real problem I have seen outside of the errors showing is Plex Media Server having an issue streaming my media that is kept on a separate hard drive from the main system.  After the errors show the system continues to boot to Openbox.  I was hope someone could tell me what the errors are and how to not get them anymore.  I have posted the dmesg log below, thanks in advanced for any help.
    [ 0.000000] Initializing cgroup subsys cpuset
    [ 0.000000] Initializing cgroup subsys cpu
    [ 0.000000] Initializing cgroup subsys cpuacct
    [ 0.000000] Linux version 3.12.1-1-ARCH (tobias@T-POWA-LX) (gcc version 4.8.2 (GCC) ) #1 SMP PREEMPT Thu Nov 21 08:18:42 CET 2013
    [ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=f3bb4b9d-d9f1-4ef7-9180-07f1d4a00fc2 rw quiet
    [ 0.000000] e820: BIOS-provided physical RAM map:
    [ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009f3ff] usable
    [ 0.000000] BIOS-e820: [mem 0x000000000009f400-0x000000000009ffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bffdffff] usable
    [ 0.000000] BIOS-e820: [mem 0x00000000bffe0000-0x00000000bffe2fff] ACPI NVS
    [ 0.000000] BIOS-e820: [mem 0x00000000bffe3000-0x00000000bffeffff] ACPI data
    [ 0.000000] BIOS-e820: [mem 0x00000000bfff0000-0x00000000bfffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved
    [ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000013fffffff] usable
    [ 0.000000] NX (Execute Disable) protection: active
    [ 0.000000] SMBIOS 2.5 present.
    [ 0.000000] DMI: Unknow Unknow/HA04, BIOS 6.00 PG 04/16/2008
    [ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
    [ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
    [ 0.000000] No AGP bridge found
    [ 0.000000] e820: last_pfn = 0x140000 max_arch_pfn = 0x400000000
    [ 0.000000] MTRR default type: uncachable
    [ 0.000000] MTRR fixed ranges enabled:
    [ 0.000000] 00000-9FFFF write-back
    [ 0.000000] A0000-BFFFF uncachable
    [ 0.000000] C0000-C7FFF write-protect
    [ 0.000000] C8000-FFFFF uncachable
    [ 0.000000] MTRR variable ranges enabled:
    [ 0.000000] 0 base 0000000000 mask FF80000000 write-back
    [ 0.000000] 1 base 0080000000 mask FFC0000000 write-back
    [ 0.000000] 2 base 0100000000 mask FFC0000000 write-back
    [ 0.000000] 3 disabled
    [ 0.000000] 4 disabled
    [ 0.000000] 5 disabled
    [ 0.000000] 6 disabled
    [ 0.000000] 7 disabled
    [ 0.000000] TOM2: 0000000140000000 aka 5120M
    [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
    [ 0.000000] e820: update [mem 0xc0000000-0xffffffff] usable ==> reserved
    [ 0.000000] e820: last_pfn = 0xbffe0 max_arch_pfn = 0x400000000
    [ 0.000000] found SMP MP-table at [mem 0x000f3c70-0x000f3c7f] mapped at [ffff8800000f3c70]
    [ 0.000000] Scanning 1 areas for low memory corruption
    [ 0.000000] Base memory trampoline at [ffff880000099000] 99000 size 24576
    [ 0.000000] init_memory_mapping: [mem 0x00000000-0x000fffff]
    [ 0.000000] [mem 0x00000000-0x000fffff] page 4k
    [ 0.000000] BRK [0x01b32000, 0x01b32fff] PGTABLE
    [ 0.000000] BRK [0x01b33000, 0x01b33fff] PGTABLE
    [ 0.000000] BRK [0x01b34000, 0x01b34fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x13fe00000-0x13fffffff]
    [ 0.000000] [mem 0x13fe00000-0x13fffffff] page 2M
    [ 0.000000] BRK [0x01b35000, 0x01b35fff] PGTABLE
    [ 0.000000] init_memory_mapping: [mem 0x13c000000-0x13fdfffff]
    [ 0.000000] [mem 0x13c000000-0x13fdfffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x100000000-0x13bffffff]
    [ 0.000000] [mem 0x100000000-0x13bffffff] page 2M
    [ 0.000000] init_memory_mapping: [mem 0x00100000-0xbffdffff]
    [ 0.000000] [mem 0x00100000-0x001fffff] page 4k
    [ 0.000000] [mem 0x00200000-0xbfdfffff] page 2M
    [ 0.000000] [mem 0xbfe00000-0xbffdffff] page 4k
    [ 0.000000] RAMDISK: [mem 0x37a04000-0x37cf9fff]
    [ 0.000000] ACPI: RSDP 00000000000f7e70 00024 (v02 790FX )
    [ 0.000000] ACPI: XSDT 00000000bffe3080 00044 (v01 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: FACP 00000000bffeaa40 000F4 (v03 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: DSDT 00000000bffe3200 07822 (v01 790FX AWRDACPI 00001000 MSFT 03000000)
    [ 0.000000] ACPI: FACS 00000000bffe0000 00040
    [ 0.000000] ACPI: HPET 00000000bffeac00 00038 (v01 790FX AWRDACPI 42302E31 AWRD 00000098)
    [ 0.000000] ACPI: MCFG 00000000bffeac40 0003C (v01 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: APIC 00000000bffeab40 00084 (v01 790FX AWRDACPI 42302E31 AWRD 00000000)
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] Scanning NUMA topology in Northbridge 24
    [ 0.000000] No NUMA configuration found
    [ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000013fffffff]
    [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x13fffffff]
    [ 0.000000] NODE_DATA [mem 0x13fff8000-0x13fffcfff]
    [ 0.000000] [ffffea0000000000-ffffea0004ffffff] PMD -> [ffff88013b600000-ffff88013f5fffff] on node 0
    [ 0.000000] Zone ranges:
    [ 0.000000] DMA [mem 0x00001000-0x00ffffff]
    [ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
    [ 0.000000] Normal [mem 0x100000000-0x13fffffff]
    [ 0.000000] Movable zone start for each node
    [ 0.000000] Early memory node ranges
    [ 0.000000] node 0: [mem 0x00001000-0x0009efff]
    [ 0.000000] node 0: [mem 0x00100000-0xbffdffff]
    [ 0.000000] node 0: [mem 0x100000000-0x13fffffff]
    [ 0.000000] On node 0 totalpages: 1048446
    [ 0.000000] DMA zone: 64 pages used for memmap
    [ 0.000000] DMA zone: 21 pages reserved
    [ 0.000000] DMA zone: 3998 pages, LIFO batch:0
    [ 0.000000] DMA32 zone: 12224 pages used for memmap
    [ 0.000000] DMA32 zone: 782304 pages, LIFO batch:31
    [ 0.000000] Normal zone: 4096 pages used for memmap
    [ 0.000000] Normal zone: 262144 pages, LIFO batch:31
    [ 0.000000] Detected use of extended apic ids on hypertransport bus
    [ 0.000000] ACPI: PM-Timer IO Port: 0x4008
    [ 0.000000] ACPI: Local APIC address 0xfee00000
    [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
    [ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
    [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
    [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
    [ 0.000000] IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
    [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
    [ 0.000000] ACPI: IRQ0 used by override.
    [ 0.000000] ACPI: IRQ2 used by override.
    [ 0.000000] ACPI: IRQ9 used by override.
    [ 0.000000] Using ACPI (MADT) for SMP configuration information
    [ 0.000000] ACPI: HPET id: 0x10b9a201 base: 0xfed00000
    [ 0.000000] smpboot: Allowing 4 CPUs, 2 hotplug CPUs
    [ 0.000000] nr_irqs_gsi: 40
    [ 0.000000] PM: Registered nosave memory: [mem 0x0009f000-0x0009ffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000effff]
    [ 0.000000] PM: Registered nosave memory: [mem 0x000f0000-0x000fffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbffe0000-0xbffe2fff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbffe3000-0xbffeffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xbfff0000-0xbfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xc0000000-0xdfffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xe0000000-0xefffffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xf0000000-0xfebfffff]
    [ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xffffffff]
    [ 0.000000] e820: [mem 0xc0000000-0xdfffffff] available for PCI devices
    [ 0.000000] Booting paravirtualized kernel on bare hardware
    [ 0.000000] setup_percpu: NR_CPUS:128 nr_cpumask_bits:128 nr_cpu_ids:4 nr_node_ids:1
    [ 0.000000] PERCPU: Embedded 29 pages/cpu @ffff88013fc00000 s86464 r8192 d24128 u524288
    [ 0.000000] pcpu-alloc: s86464 r8192 d24128 u524288 alloc=1*2097152
    [ 0.000000] pcpu-alloc: [0] 0 1 2 3
    [ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 1032041
    [ 0.000000] Policy zone: Normal
    [ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-linux root=UUID=f3bb4b9d-d9f1-4ef7-9180-07f1d4a00fc2 rw quiet
    [ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
    [ 0.000000] Checking aperture...
    [ 0.000000] No AGP bridge found
    [ 0.000000] Node 0: aperture @ b4000000 size 32 MB
    [ 0.000000] Aperture pointing to e820 RAM. Ignoring.
    [ 0.000000] Your BIOS doesn't leave a aperture memory hole
    [ 0.000000] Please enable the IOMMU option in the BIOS setup
    [ 0.000000] This costs you 64 MB of RAM
    [ 0.000000] Mapping aperture over 65536 KB of RAM @ b4000000
    [ 0.000000] PM: Registered nosave memory: [mem 0xb4000000-0xb7ffffff]
    [ 0.000000] Memory: 3981312K/4193784K available (5115K kernel code, 806K rwdata, 1708K rodata, 1144K init, 1288K bss, 212472K reserved)
    [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
    [ 0.000000] Preemptible hierarchical RCU implementation.
    [ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
    [ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
    [ 0.000000] RCU restricting CPUs from NR_CPUS=128 to nr_cpu_ids=4.
    [ 0.000000] NR_IRQS:8448 nr_irqs:712 16
    [ 0.000000] spurious 8259A interrupt: IRQ7.
    [ 0.000000] Console: colour dummy device 80x25
    [ 0.000000] console [tty0] enabled
    [ 0.000000] allocated 16777216 bytes of page_cgroup
    [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
    [ 0.000000] hpet clockevent registered
    [ 0.000000] tsc: Fast TSC calibration failed
    [ 0.000000] tsc: Unable to calibrate against PIT
    [ 0.000000] tsc: using HPET reference calibration
    [ 0.000000] tsc: Detected 2700.249 MHz processor
    [ 0.000000] tsc: Marking TSC unstable due to TSCs unsynchronized
    [ 0.013338] Calibrating delay loop (skipped), value calculated using timer frequency.. 5402.51 BogoMIPS (lpj=9000830)
    [ 0.013342] pid_max: default: 32768 minimum: 301
    [ 0.013386] Security Framework initialized
    [ 0.013395] AppArmor: AppArmor disabled by boot time parameter
    [ 0.013396] Yama: becoming mindful.
    [ 0.013706] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
    [ 0.015721] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
    [ 0.017157] Mount-cache hash table entries: 256
    [ 0.017396] Initializing cgroup subsys memory
    [ 0.017414] Initializing cgroup subsys devices
    [ 0.017417] Initializing cgroup subsys freezer
    [ 0.017418] Initializing cgroup subsys net_cls
    [ 0.017420] Initializing cgroup subsys blkio
    [ 0.017442] tseg: 0000000000
    [ 0.017449] CPU: Physical Processor ID: 0
    [ 0.017450] CPU: Processor Core ID: 0
    [ 0.017452] mce: CPU supports 5 MCE banks
    [ 0.017458] LVT offset 0 assigned for vector 0xf9
    [ 0.017462] process: using AMD E400 aware idle routine
    [ 0.017464] Last level iTLB entries: 4KB 512, 2MB 8, 4MB 4
    Last level dTLB entries: 4KB 512, 2MB 8, 4MB 4
    tlb_flushall_shift: 4
    [ 0.017546] Freeing SMP alternatives memory: 20K (ffffffff819e9000 - ffffffff819ee000)
    [ 0.018244] ACPI: Core revision 20130725
    [ 0.021196] ACPI: All ACPI Tables successfully acquired
    [ 0.023362] ftrace: allocating 20290 entries in 80 pages
    [ 0.034097] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
    [ 0.068081] smpboot: CPU0: AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ (fam: 0f, model: 6b, stepping: 02)
    [ 0.069999] Performance Events: AMD PMU driver.
    [ 0.069999] ... version: 0
    [ 0.069999] ... bit width: 48
    [ 0.069999] ... generic registers: 4
    [ 0.069999] ... value mask: 0000ffffffffffff
    [ 0.069999] ... max period: 00007fffffffffff
    [ 0.069999] ... fixed-purpose events: 0
    [ 0.069999] ... event mask: 000000000000000f
    [ 0.083388] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
    [ 0.090068] smpboot: Booting Node 0, Processors # 1 OK
    [ 0.183403] Brought up 2 CPUs
    [ 0.183406] smpboot: Total of 2 processors activated (10805.89 BogoMIPS)
    [ 0.183927] devtmpfs: initialized
    [ 0.188111] PM: Registering ACPI NVS region [mem 0xbffe0000-0xbffe2fff] (12288 bytes)
    [ 0.188111] RTC time: 8:27:34, date: 12/02/13
    [ 0.188111] NET: Registered protocol family 16
    [ 0.188127] cpuidle: using governor ladder
    [ 0.188128] cpuidle: using governor menu
    [ 0.188133] node 0 link 0: io port [b000, ffff]
    [ 0.188135] TOM: 00000000c0000000 aka 3072M
    [ 0.188137] node 0 link 0: mmio [a0000, bffff]
    [ 0.188140] node 0 link 0: mmio [c0000000, dfffffff]
    [ 0.188142] node 0 link 0: mmio [f0000000, fe02ffff]
    [ 0.188144] node 0 link 0: mmio [e0000000, e04fffff]
    [ 0.188145] TOM2: 0000000140000000 aka 5120M
    [ 0.188148] bus: [bus 00-04] on node 0 link 0
    [ 0.188149] bus: 00 [io 0x0000-0xffff]
    [ 0.188151] bus: 00 [mem 0x000a0000-0x000bffff]
    [ 0.188152] bus: 00 [mem 0xc0000000-0xefffffff]
    [ 0.188153] bus: 00 [mem 0xf0000000-0xffffffff]
    [ 0.188155] bus: 00 [mem 0x140000000-0xfcffffffff]
    [ 0.188168] ACPI: bus type PCI registered
    [ 0.188170] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
    [ 0.188231] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
    [ 0.188234] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
    [ 0.199259] PCI: Using configuration type 1 for base access
    [ 0.199433] mtrr: your CPUs had inconsistent variable MTRR settings
    [ 0.199434] mtrr: probably your BIOS does not setup all CPUs.
    [ 0.199435] mtrr: corrected configuration.
    [ 0.200005] bio: create slab <bio-0> at 0
    [ 0.200048] ACPI: Added _OSI(Module Device)
    [ 0.200050] ACPI: Added _OSI(Processor Device)
    [ 0.200052] ACPI: Added _OSI(3.0 _SCP Extensions)
    [ 0.200053] ACPI: Added _OSI(Processor Aggregator Device)
    [ 0.200693] ACPI: EC: Look up EC in DSDT
    [ 0.201612] ACPI: Executed 1 blocks of module-level executable AML code
    [ 0.204741] ACPI: Interpreter enabled
    [ 0.204755] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S2_] (20130725/hwxface-571)
    [ 0.204760] ACPI Exception: AE_NOT_FOUND, While evaluating Sleep State [\_S3_] (20130725/hwxface-571)
    [ 0.204770] ACPI: (supports S0 S1 S4 S5)
    [ 0.204771] ACPI: Using IOAPIC for interrupt routing
    [ 0.204841] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
    [ 0.204933] ACPI: No dock devices found.
    [ 0.217777] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
    [ 0.217785] acpi PNP0A03:00: ACPI _OSC support notification failed, disabling PCIe ASPM
    [ 0.217787] acpi PNP0A03:00: Unable to request _OSC control (_OSC support mask: 0x08)
    [ 0.218038] ACPI: \_SB_.PCI0.SYSR: can't evaluate _ADR (0x5)
    [ 0.218040] ACPI: \_SB_.PCI0.FDC0: can't evaluate _ADR (0x5)
    [ 0.218043] ACPI: \_SB_.PCI0.UAR1: can't evaluate _ADR (0x5)
    [ 0.218045] ACPI: \_SB_.PCI0.UAR2: can't evaluate _ADR (0x5)
    [ 0.218047] ACPI: \_SB_.PCI0.IRDA: can't evaluate _ADR (0x5)
    [ 0.218050] ACPI: \_SB_.PCI0.LPT1: can't evaluate _ADR (0x5)
    [ 0.218052] ACPI: \_SB_.PCI0.ECP1: can't evaluate _ADR (0x5)
    [ 0.218054] ACPI: \_SB_.PCI0.PS2M: can't evaluate _ADR (0x5)
    [ 0.218057] ACPI: \_SB_.PCI0.PS2K: can't evaluate _ADR (0x5)
    [ 0.218058] PCI host bridge to bus 0000:00
    [ 0.218061] pci_bus 0000:00: root bus resource [bus 00-ff]
    [ 0.218063] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
    [ 0.218065] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
    [ 0.218068] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
    [ 0.218069] pci_bus 0000:00: root bus resource [mem 0x000c0000-0x000dffff]
    [ 0.218072] pci_bus 0000:00: root bus resource [mem 0xbfff0000-0xffffffff]
    [ 0.218083] pci 0000:00:00.0: [1002:5956] type 00 class 0x060000
    [ 0.218097] pci 0000:00:00.0: reg 0x1c: [mem 0xe0000000-0xffffffff 64bit]
    [ 0.218196] pci 0000:00:02.0: [1002:5978] type 01 class 0x060400
    [ 0.218233] pci 0000:00:02.0: PME# supported from D0 D3hot D3cold
    [ 0.218280] pci 0000:00:02.0: System wakeup disabled by ACPI
    [ 0.218322] pci 0000:00:06.0: [1002:597c] type 01 class 0x060400
    [ 0.218357] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
    [ 0.218402] pci 0000:00:06.0: System wakeup disabled by ACPI
    [ 0.218438] pci 0000:00:07.0: [1002:597d] type 01 class 0x060400
    [ 0.218473] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
    [ 0.218518] pci 0000:00:07.0: System wakeup disabled by ACPI
    [ 0.218573] pci 0000:00:12.0: [1002:4380] type 00 class 0x01018f
    [ 0.218594] pci 0000:00:12.0: reg 0x10: [io 0xff00-0xff07]
    [ 0.218605] pci 0000:00:12.0: reg 0x14: [io 0xfe00-0xfe03]
    [ 0.218616] pci 0000:00:12.0: reg 0x18: [io 0xfd00-0xfd07]
    [ 0.218626] pci 0000:00:12.0: reg 0x1c: [io 0xfc00-0xfc03]
    [ 0.218637] pci 0000:00:12.0: reg 0x20: [io 0xfb00-0xfb0f]
    [ 0.218648] pci 0000:00:12.0: reg 0x24: [mem 0xfe02f000-0xfe02f3ff]
    [ 0.218671] pci 0000:00:12.0: set SATA to AHCI mode
    [ 0.218780] pci 0000:00:13.0: [1002:4387] type 00 class 0x0c0310
    [ 0.218795] pci 0000:00:13.0: reg 0x10: [mem 0xfe02e000-0xfe02efff]
    [ 0.218895] pci 0000:00:13.0: System wakeup disabled by ACPI
    [ 0.218932] pci 0000:00:13.1: [1002:4388] type 00 class 0x0c0310
    [ 0.218947] pci 0000:00:13.1: reg 0x10: [mem 0xfe02d000-0xfe02dfff]
    [ 0.219048] pci 0000:00:13.1: System wakeup disabled by ACPI
    [ 0.219087] pci 0000:00:13.2: [1002:4389] type 00 class 0x0c0310
    [ 0.219102] pci 0000:00:13.2: reg 0x10: [mem 0xfe02c000-0xfe02cfff]
    [ 0.219203] pci 0000:00:13.2: System wakeup disabled by ACPI
    [ 0.219238] pci 0000:00:13.3: [1002:438a] type 00 class 0x0c0310
    [ 0.219253] pci 0000:00:13.3: reg 0x10: [mem 0xfe02b000-0xfe02bfff]
    [ 0.219354] pci 0000:00:13.3: System wakeup disabled by ACPI
    [ 0.219390] pci 0000:00:13.4: [1002:438b] type 00 class 0x0c0310
    [ 0.219405] pci 0000:00:13.4: reg 0x10: [mem 0xfe02a000-0xfe02afff]
    [ 0.219506] pci 0000:00:13.4: System wakeup disabled by ACPI
    [ 0.219554] pci 0000:00:13.5: [1002:4386] type 00 class 0x0c0320
    [ 0.219575] pci 0000:00:13.5: reg 0x10: [mem 0xfe029000-0xfe0290ff]
    [ 0.219665] pci 0000:00:13.5: supports D1 D2
    [ 0.219668] pci 0000:00:13.5: PME# supported from D0 D1 D2 D3hot
    [ 0.219716] pci 0000:00:13.5: System wakeup disabled by ACPI
    [ 0.219759] pci 0000:00:14.0: [1002:4385] type 00 class 0x0c0500
    [ 0.219783] pci 0000:00:14.0: reg 0x10: [io 0x0b00-0x0b0f]
    [ 0.219793] pci 0000:00:14.0: reg 0x14: [mem 0xfed00000-0xfed003ff]
    [ 0.219934] pci 0000:00:14.1: [1002:438c] type 00 class 0x01018a
    [ 0.219952] pci 0000:00:14.1: reg 0x10: [io 0x0000-0x0007]
    [ 0.219963] pci 0000:00:14.1: reg 0x14: [io 0x0000-0x0003]
    [ 0.219974] pci 0000:00:14.1: reg 0x18: [io 0x0000-0x0007]
    [ 0.219984] pci 0000:00:14.1: reg 0x1c: [io 0x0000-0x0003]
    [ 0.219995] pci 0000:00:14.1: reg 0x20: [io 0xf900-0xf90f]
    [ 0.220124] pci 0000:00:14.2: [1002:4383] type 00 class 0x040300
    [ 0.220151] pci 0000:00:14.2: reg 0x10: [mem 0xfe024000-0xfe027fff 64bit]
    [ 0.220234] pci 0000:00:14.2: PME# supported from D0 D3hot D3cold
    [ 0.220287] pci 0000:00:14.2: System wakeup disabled by ACPI
    [ 0.220322] pci 0000:00:14.3: [1002:438d] type 00 class 0x060100
    [ 0.220460] pci 0000:00:14.4: [1002:4384] type 01 class 0x060401
    [ 0.220536] pci 0000:00:14.4: System wakeup disabled by ACPI
    [ 0.220575] pci 0000:00:18.0: [1022:1100] type 00 class 0x060000
    [ 0.220645] pci 0000:00:18.1: [1022:1101] type 00 class 0x060000
    [ 0.220712] pci 0000:00:18.2: [1022:1102] type 00 class 0x060000
    [ 0.220779] pci 0000:00:18.3: [1022:1103] type 00 class 0x060000
    [ 0.220904] pci 0000:01:00.0: [10de:042c] type 00 class 0x030000
    [ 0.220917] pci 0000:01:00.0: reg 0x10: [mem 0xfa000000-0xfaffffff]
    [ 0.220929] pci 0000:01:00.0: reg 0x14: [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.220942] pci 0000:01:00.0: reg 0x1c: [mem 0xf8000000-0xf9ffffff 64bit]
    [ 0.220951] pci 0000:01:00.0: reg 0x24: [io 0xcf00-0xcf7f]
    [ 0.220959] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    [ 0.226682] pci 0000:00:02.0: PCI bridge to [bus 01]
    [ 0.226687] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
    [ 0.226690] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xfbffffff]
    [ 0.226694] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.226751] pci 0000:02:00.0: [11ab:4364] type 00 class 0x020000
    [ 0.226769] pci 0000:02:00.0: reg 0x10: [mem 0xfdcfc000-0xfdcfffff 64bit]
    [ 0.226780] pci 0000:02:00.0: reg 0x18: [io 0xee00-0xeeff]
    [ 0.226813] pci 0000:02:00.0: reg 0x30: [mem 0x00000000-0x0001ffff pref]
    [ 0.226865] pci 0000:02:00.0: supports D1 D2
    [ 0.226868] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
    [ 0.233345] pci 0000:00:06.0: PCI bridge to [bus 02]
    [ 0.233349] pci 0000:00:06.0: bridge window [io 0xe000-0xefff]
    [ 0.233352] pci 0000:00:06.0: bridge window [mem 0xfdc00000-0xfdcfffff]
    [ 0.233356] pci 0000:00:06.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.233407] pci 0000:03:00.0: [197b:2363] type 00 class 0x010185
    [ 0.233479] pci 0000:03:00.0: reg 0x24: [mem 0xfdefe000-0xfdefffff]
    [ 0.233491] pci 0000:03:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref]
    [ 0.233534] pci 0000:03:00.0: PME# supported from D3hot
    [ 0.233590] pci 0000:03:00.1: [197b:2363] type 00 class 0x010185
    [ 0.233608] pci 0000:03:00.1: reg 0x10: [io 0xdf00-0xdf07]
    [ 0.233617] pci 0000:03:00.1: reg 0x14: [io 0xde00-0xde03]
    [ 0.233626] pci 0000:03:00.1: reg 0x18: [io 0xdd00-0xdd07]
    [ 0.233635] pci 0000:03:00.1: reg 0x1c: [io 0xdc00-0xdc03]
    [ 0.233644] pci 0000:03:00.1: reg 0x20: [io 0xdb00-0xdb0f]
    [ 0.233730] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
    [ 0.233738] pci 0000:00:07.0: PCI bridge to [bus 03]
    [ 0.233742] pci 0000:00:07.0: bridge window [io 0xd000-0xdfff]
    [ 0.233745] pci 0000:00:07.0: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.233749] pci 0000:00:07.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
    [ 0.233826] pci 0000:00:14.4: PCI bridge to [bus 04] (subtractive decode)
    [ 0.233831] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff]
    [ 0.233835] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff]
    [ 0.233840] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff pref]
    [ 0.233843] pci 0000:00:14.4: bridge window [io 0x0000-0x0cf7] (subtractive decode)
    [ 0.233845] pci 0000:00:14.4: bridge window [io 0x0d00-0xffff] (subtractive decode)
    [ 0.233847] pci 0000:00:14.4: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
    [ 0.233850] pci 0000:00:14.4: bridge window [mem 0x000c0000-0x000dffff] (subtractive decode)
    [ 0.233852] pci 0000:00:14.4: bridge window [mem 0xbfff0000-0xffffffff] (subtractive decode)
    [ 0.234022] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234071] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234118] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234165] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234213] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234260] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234308] ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.234355] ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 10 11) *0, disabled.
    [ 0.235135] ACPI: Enabled 2 GPEs in block 00 to 1F
    [ 0.235141] ACPI: \_SB_.PCI0: notify handler is installed
    [ 0.235177] Found 1 acpi root devices
    [ 0.235262] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
    [ 0.235262] vgaarb: loaded
    [ 0.235262] vgaarb: bridge control possible 0000:01:00.0
    [ 0.235262] PCI: Using ACPI for IRQ routing
    [ 0.244778] PCI: pci_cache_line_size set to 64 bytes
    [ 0.244786] pci 0000:00:00.0: address space collision: [mem 0xe0000000-0xffffffff 64bit] conflicts with PCI Bus 0000:01 [mem 0xf8000000-0xfbffffff]
    [ 0.244846] e820: reserve RAM buffer [mem 0x0009f400-0x0009ffff]
    [ 0.244848] e820: reserve RAM buffer [mem 0xbffe0000-0xbfffffff]
    [ 0.244956] NetLabel: Initializing
    [ 0.244957] NetLabel: domain hash size = 128
    [ 0.244959] NetLabel: protocols = UNLABELED CIPSOv4
    [ 0.244971] NetLabel: unlabeled traffic allowed by default
    [ 0.244995] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
    [ 0.244999] hpet0: 4 comparators, 32-bit 14.318180 MHz counter
    [ 0.246697] Switched to clocksource hpet
    [ 0.251917] pnp: PnP ACPI init
    [ 0.251938] ACPI: bus type PNP registered
    [ 0.252120] pnp 00:00: disabling [mem 0x00000000-0x00000fff window] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.252151] pnp 00:00: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:01:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
    [ 0.252156] pnp 00:00: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:02:00.0 BAR 6 [mem 0x00000000-0x0001ffff pref]
    [ 0.252160] pnp 00:00: disabling [mem 0x00000000-0x00000fff window disabled] because it overlaps 0000:03:00.0 BAR 6 [mem 0x00000000-0x0000ffff pref]
    [ 0.252195] system 00:00: [io 0x4100-0x411f] has been reserved
    [ 0.252199] system 00:00: [io 0x0228-0x022f] has been reserved
    [ 0.252201] system 00:00: [io 0x040b] has been reserved
    [ 0.252204] system 00:00: [io 0x04d6] has been reserved
    [ 0.252206] system 00:00: [io 0x0c00-0x0c01] has been reserved
    [ 0.252209] system 00:00: [io 0x0c14] has been reserved
    [ 0.252211] system 00:00: [io 0x0c50-0x0c52] has been reserved
    [ 0.252214] system 00:00: [io 0x0c6c-0x0c6d] has been reserved
    [ 0.252216] system 00:00: [io 0x0c6f] has been reserved
    [ 0.252219] system 00:00: [io 0x0cd0-0x0cd1] has been reserved
    [ 0.252221] system 00:00: [io 0x0cd2-0x0cd3] has been reserved
    [ 0.252224] system 00:00: [io 0x0cd4-0x0cdf] has been reserved
    [ 0.252226] system 00:00: [io 0x4000-0x40fe] could not be reserved
    [ 0.252229] system 00:00: [io 0x4210-0x4217] has been reserved
    [ 0.252231] system 00:00: [io 0x0b10-0x0b1f] has been reserved
    [ 0.252235] system 00:00: [mem 0xfee00400-0xfee00fff window] has been reserved
    [ 0.252239] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.252336] pnp 00:01: [dma 4]
    [ 0.252360] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
    [ 0.252442] pnp 00:02: Plug and Play ACPI device, IDs PNP0103 (active)
    [ 0.252487] pnp 00:03: Plug and Play ACPI device, IDs PNP0b00 (active)
    [ 0.252510] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
    [ 0.252544] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
    [ 0.252614] system 00:06: [io 0x04d0-0x04d1] has been reserved
    [ 0.252617] system 00:06: [io 0x0f40-0x0f45] has been reserved
    [ 0.252620] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
    [ 0.252767] pnp 00:07: [dma 2]
    [ 0.252808] pnp 00:07: Plug and Play ACPI device, IDs PNP0700 (active)
    [ 0.253041] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
    [ 0.253372] pnp 00:09: Plug and Play ACPI device, IDs PNP0510 (active)
    [ 0.253612] pnp 00:0a: Plug and Play ACPI device, IDs PNP0400 (active)
    [ 0.253805] pnp 00:0b: Plug and Play ACPI device, IDs PNP0303 (active)
    [ 0.253859] pnp 00:0c: disabling [mem 0x000f0000-0x000fffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253862] pnp 00:0c: disabling [mem 0x00000000-0x001fffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253865] pnp 00:0c: disabling [mem 0x00000000-0x0009ffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253868] pnp 00:0c: disabling [mem 0x00100000-0xbffdffff] because it overlaps 0000:00:00.0 BAR 3 [mem 0x00000000-0x1fffffff 64bit]
    [ 0.253878] pnp 00:0c: disabling [mem 0xfed00000-0xfed000ff] because it overlaps 0000:00:14.0 BAR 1 [mem 0xfed00000-0xfed003ff]
    [ 0.253911] system 00:0c: [mem 0xbffe0000-0xbfffffff] could not be reserved
    [ 0.253914] system 00:0c: [mem 0xffff0000-0xffffffff] has been reserved
    [ 0.253917] system 00:0c: [mem 0xfec00000-0xfec00fff] could not be reserved
    [ 0.253919] system 00:0c: [mem 0xfee00000-0xfee00fff] could not be reserved
    [ 0.253922] system 00:0c: [mem 0xfff80000-0xfffeffff] has been reserved
    [ 0.253924] system 00:0c: Plug and Play ACPI device, IDs PNP0c01 (active)
    [ 0.253938] pnp: PnP ACPI: found 13 devices
    [ 0.253939] ACPI: bus type PNP unregistered
    [ 0.261111] pci 0000:01:00.0: BAR 6: assigned [mem 0xfb000000-0xfb01ffff pref]
    [ 0.261115] pci 0000:00:02.0: PCI bridge to [bus 01]
    [ 0.261118] pci 0000:00:02.0: bridge window [io 0xc000-0xcfff]
    [ 0.261121] pci 0000:00:02.0: bridge window [mem 0xf8000000-0xfbffffff]
    [ 0.261124] pci 0000:00:02.0: bridge window [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.261129] pci 0000:02:00.0: BAR 6: assigned [mem 0xfdf00000-0xfdf1ffff pref]
    [ 0.261131] pci 0000:00:06.0: PCI bridge to [bus 02]
    [ 0.261133] pci 0000:00:06.0: bridge window [io 0xe000-0xefff]
    [ 0.261136] pci 0000:00:06.0: bridge window [mem 0xfdc00000-0xfdcfffff]
    [ 0.261139] pci 0000:00:06.0: bridge window [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.261144] pci 0000:03:00.0: BAR 6: assigned [mem 0xfdd00000-0xfdd0ffff pref]
    [ 0.261146] pci 0000:00:07.0: PCI bridge to [bus 03]
    [ 0.261148] pci 0000:00:07.0: bridge window [io 0xd000-0xdfff]
    [ 0.261151] pci 0000:00:07.0: bridge window [mem 0xfde00000-0xfdefffff]
    [ 0.261154] pci 0000:00:07.0: bridge window [mem 0xfdd00000-0xfddfffff 64bit pref]
    [ 0.261158] pci 0000:00:14.4: PCI bridge to [bus 04]
    [ 0.261161] pci 0000:00:14.4: bridge window [io 0xb000-0xbfff]
    [ 0.261166] pci 0000:00:14.4: bridge window [mem 0xfdb00000-0xfdbfffff]
    [ 0.261171] pci 0000:00:14.4: bridge window [mem 0xfda00000-0xfdafffff pref]
    [ 0.261178] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
    [ 0.261180] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
    [ 0.261182] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.261184] pci_bus 0000:00: resource 7 [mem 0x000c0000-0x000dffff]
    [ 0.261186] pci_bus 0000:00: resource 8 [mem 0xbfff0000-0xffffffff]
    [ 0.261188] pci_bus 0000:01: resource 0 [io 0xc000-0xcfff]
    [ 0.261190] pci_bus 0000:01: resource 1 [mem 0xf8000000-0xfbffffff]
    [ 0.261192] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff 64bit pref]
    [ 0.261195] pci_bus 0000:02: resource 0 [io 0xe000-0xefff]
    [ 0.261197] pci_bus 0000:02: resource 1 [mem 0xfdc00000-0xfdcfffff]
    [ 0.261199] pci_bus 0000:02: resource 2 [mem 0xfdf00000-0xfdffffff 64bit pref]
    [ 0.261201] pci_bus 0000:03: resource 0 [io 0xd000-0xdfff]
    [ 0.261203] pci_bus 0000:03: resource 1 [mem 0xfde00000-0xfdefffff]
    [ 0.261205] pci_bus 0000:03: resource 2 [mem 0xfdd00000-0xfddfffff 64bit pref]
    [ 0.261207] pci_bus 0000:04: resource 0 [io 0xb000-0xbfff]
    [ 0.261209] pci_bus 0000:04: resource 1 [mem 0xfdb00000-0xfdbfffff]
    [ 0.261211] pci_bus 0000:04: resource 2 [mem 0xfda00000-0xfdafffff pref]
    [ 0.261213] pci_bus 0000:04: resource 4 [io 0x0000-0x0cf7]
    [ 0.261215] pci_bus 0000:04: resource 5 [io 0x0d00-0xffff]
    [ 0.261217] pci_bus 0000:04: resource 6 [mem 0x000a0000-0x000bffff]
    [ 0.261219] pci_bus 0000:04: resource 7 [mem 0x000c0000-0x000dffff]
    [ 0.261221] pci_bus 0000:04: resource 8 [mem 0xbfff0000-0xffffffff]
    [ 0.261266] NET: Registered protocol family 2
    [ 0.261475] TCP established hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.261731] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
    [ 0.261986] TCP: Hash tables configured (established 32768 bind 32768)
    [ 0.262046] TCP: reno registered
    [ 0.262057] UDP hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.262089] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
    [ 0.262209] NET: Registered protocol family 1
    [ 0.616902] pci 0000:01:00.0: Boot video device
    [ 0.616913] PCI: CLS 32 bytes, default 64
    [ 0.616966] Unpacking initramfs...
    [ 0.676909] Freeing initrd memory: 3032K (ffff880037a04000 - ffff880037cfa000)
    [ 0.677630] PCI-DMA: Disabling AGP.
    [ 0.677710] PCI-DMA: aperture base @ b4000000 size 65536 KB
    [ 0.677712] PCI-DMA: using GART IOMMU.
    [ 0.677715] PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
    [ 0.682349] Scanning for low memory corruption every 60 seconds
    [ 0.682695] audit: initializing netlink socket (disabled)
    [ 0.682709] type=2000 audit(1385972853.679:1): initialized
    [ 0.693650] HugeTLB registered 2 MB page size, pre-allocated 0 pages
    [ 0.695128] zbud: loaded
    [ 0.695281] VFS: Disk quotas dquot_6.5.2
    [ 0.695335] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
    [ 0.695554] msgmni has been set to 7910
    [ 0.695944] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
    [ 0.695993] io scheduler noop registered
    [ 0.695995] io scheduler deadline registered
    [ 0.696025] io scheduler cfq registered (default)
    [ 0.696145] pcieport 0000:00:02.0: irq 40 for MSI/MSI-X
    [ 0.696229] pcieport 0000:00:06.0: irq 41 for MSI/MSI-X
    [ 0.696299] pcieport 0000:00:07.0: irq 42 for MSI/MSI-X
    [ 0.696374] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
    [ 0.696391] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
    [ 0.696444] vesafb: mode is 640x480x32, linelength=2560, pages=0
    [ 0.696445] vesafb: scrolling: redraw
    [ 0.696447] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
    [ 0.696504] vesafb: framebuffer at 0xf9000000, mapped to 0xffffc90010800000, using 1216k, total 1216k
    [ 0.702849] Console: switching to colour frame buffer device 80x30
    [ 0.709096] fb0: VESA VGA frame buffer device
    [ 0.709135] GHES: HEST is not enabled!
    [ 0.709196] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
    [ 0.729882] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
    [ 0.750605] serial8250: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
    [ 0.750958] Linux agpgart interface v0.103
    [ 0.751006] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
    [ 0.751007] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
    [ 0.751728] serio: i8042 KBD port at 0x60,0x64 irq 1
    [ 0.751860] mousedev: PS/2 mouse device common for all mice
    [ 0.751927] rtc_cmos 00:03: RTC can wake from S4
    [ 0.752067] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
    [ 0.752106] rtc_cmos 00:03: alarms up to one month, 242 bytes nvram, hpet irqs
    [ 0.752187] drop_monitor: Initializing network drop monitor service
    [ 0.752254] TCP: cubic registered
    [ 0.752361] NET: Registered protocol family 10
    [ 0.752553] NET: Registered protocol family 17
    [ 0.752565] Key type dns_resolver registered
    [ 0.752847] registered taskstats version 1
    [ 0.753423] Magic number: 9:957:471
    [ 0.753514] rtc_cmos 00:03: setting system clock to 2013-12-02 08:27:34 UTC (1385972854)
    [ 0.753559] PM: Hibernation image not present or could not be loaded.
    [ 0.755068] Freeing unused kernel memory: 1144K (ffffffff818cb000 - ffffffff819e9000)
    [ 0.755072] Write protecting the kernel read-only data: 8192k
    [ 0.758083] Freeing unused kernel memory: 1016K (ffff880001502000 - ffff880001600000)
    [ 0.759079] Freeing unused kernel memory: 340K (ffff8800017ab000 - ffff880001800000)
    [ 0.769771] systemd-udevd[47]: starting version 208
    [ 0.794492] Floppy drive(s): fd0 is 1.44M
    [ 0.803163] ACPI: bus type USB registered
    [ 0.803196] usbcore: registered new interface driver usbfs
    [ 0.803207] usbcore: registered new interface driver hub
    [ 0.804032] usbcore: registered new device driver usb
    [ 0.804145] SCSI subsystem initialized
    [ 0.804718] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
    [ 0.805817] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
    [ 0.805956] ohci-pci: OHCI PCI platform driver
    [ 0.806132] ohci-pci 0000:00:13.0: OHCI PCI host controller
    [ 0.806149] ohci-pci 0000:00:13.0: new USB bus registered, assigned bus number 1
    [ 0.806197] ohci-pci 0000:00:13.0: irq 16, io mem 0xfe02e000
    [ 0.808453] ehci-pci: EHCI PCI platform driver
    [ 0.810692] FDC 0 is a post-1991 82077
    [ 0.810859] libata version 3.00 loaded.
    [ 0.811723] pata_jmicron 0000:03:00.1: enabling device (0000 -> 0001)
    [ 0.811823] pata_jmicron 0000:03:00.1: setting latency timer to 64
    [ 0.812133] scsi0 : pata_jmicron
    [ 0.812212] scsi1 : pata_jmicron
    [ 0.812251] ata1: PATA max UDMA/100 cmd 0xdf00 ctl 0xde00 bmdma 0xdb00 irq 16
    [ 0.812253] ata2: PATA max UDMA/100 cmd 0xdd00 ctl 0xdc00 bmdma 0xdb08 irq 16
    [ 0.860877] hub 1-0:1.0: USB hub found
    [ 0.860890] hub 1-0:1.0: 2 ports detected
    [ 0.861158] ohci-pci 0000:00:13.1: OHCI PCI host controller
    [ 0.861166] ohci-pci 0000:00:13.1: new USB bus registered, assigned bus number 2
    [ 0.861205] ohci-pci 0000:00:13.1: irq 17, io mem 0xfe02d000
    [ 0.917507] hub 2-0:1.0: USB hub found
    [ 0.917518] hub 2-0:1.0: 2 ports detected
    [ 0.917709] ohci-pci 0000:00:13.2: OHCI PCI host controller
    [ 0.917715] ohci-pci 0000:00:13.2: new USB bus registered, assigned bus number 3
    [ 0.917744] ohci-pci 0000:00:13.2: irq 18, io mem 0xfe02c000
    [ 0.974160] hub 3-0:1.0: USB hub found
    [ 0.974171] hub 3-0:1.0: 2 ports detected
    [ 0.974357] ohci-pci 0000:00:13.3: OHCI PCI host controller
    [ 0.974364] ohci-pci 0000:00:13.3: new USB bus registered, assigned bus number 4
    [ 0.974382] ohci-pci 0000:00:13.3: irq 17, io mem 0xfe02b000
    [ 1.030833] hub 4-0:1.0: USB hub found
    [ 1.030843] hub 4-0:1.0: 2 ports detected
    [ 1.031028] ohci-pci 0000:00:13.4: OHCI PCI host controller
    [ 1.031034] ohci-pci 0000:00:13.4: new USB bus registered, assigned bus number 5
    [ 1.031049] ohci-pci 0000:00:13.4: irq 18, io mem 0xfe02a000
    [ 1.087499] hub 5-0:1.0: USB hub found
    [ 1.087509] hub 5-0:1.0: 2 ports detected
    [ 1.190024] usb 1-1: new low-speed USB device number 2 using ohci-pci
    [ 1.483353] usb 1-2: new low-speed USB device number 3 using ohci-pci
    [ 1.643840] usb 1-1: USB disconnect, device number 2
    [ 1.644033] usb 1-2: USB disconnect, device number 3
    [ 1.760279] ehci-pci 0000:00:13.5: EHCI Host Controller
    [ 1.760288] ehci-pci 0000:00:13.5: new USB bus registered, assigned bus number 6
    [ 1.760297] ehci-pci 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
    [ 1.760313] ehci-pci 0000:00:13.5: debug port 1
    [ 1.760381] ehci-pci 0000:00:13.5: irq 19, io mem 0xfe029000
    [ 1.770022] ehci-pci 0000:00:13.5: USB 2.0 started, EHCI 1.00
    [ 1.770182] hub 6-0:1.0: USB hub found
    [ 1.770191] hub 6-0:1.0: 10 ports detected
    [ 1.826731] hub 1-0:1.0: USB hub found
    [ 1.826742] hub 1-0:1.0: 2 ports detected
    [ 1.828066] hidraw: raw HID events driver (C) Jiri Kosina
    [ 1.828580] usbcore: registered new interface driver usbhid
    [ 1.828583] usbhid: USB HID core driver
    [ 1.883417] hub 2-0:1.0: USB hub found
    [ 1.883431] hub 2-0:1.0: 2 ports detected
    [ 1.940057] hub 3-0:1.0: USB hub found
    [ 1.940067] hub 3-0:1.0: 2 ports detected
    [ 1.996722] hub 4-0:1.0: USB hub found
    [ 1.996732] hub 4-0:1.0: 2 ports detected
    [ 2.053388] hub 5-0:1.0: USB hub found
    [ 2.053398] hub 5-0:1.0: 2 ports detected
    [ 2.053683] ahci 0000:00:12.0: version 3.0
    [ 2.053835] ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
    [ 2.053933] ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
    [ 2.053937] ahci 0000:00:12.0: flags: ncq sntf ilck led clo pmp pio ccc
    [ 2.054699] scsi2 : ahci
    [ 2.054775] scsi3 : ahci
    [ 2.054850] scsi4 : ahci
    [ 2.054920] scsi5 : ahci
    [ 2.054967] ata3: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f100 irq 22
    [ 2.054971] ata4: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f180 irq 22
    [ 2.054974] ata5: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f200 irq 22
    [ 2.054977] ata6: SATA max UDMA/133 abar m1024@0xfe02f000 port 0xfe02f280 irq 22
    [ 2.056192] scsi6 : pata_atiixp
    [ 2.056251] scsi7 : pata_atiixp
    [ 2.056292] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf900 irq 14
    [ 2.056294] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf908 irq 15
    [ 2.066728] ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
    [ 2.066733] ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part
    [ 2.067129] scsi8 : ahci
    [ 2.067200] scsi9 : ahci
    [ 2.067257] ata9: SATA max UDMA/133 abar m8192@0xfdefe000 port 0xfdefe100 irq 19
    [ 2.067260] ata10: SATA max UDMA/133 abar m8192@0xfdefe000 port 0xfdefe180 irq 19
    [ 2.213828] ata7.00: ATAPI: HL-DT-ST RW/DVD GCC-4481B, 1.04, max UDMA/33
    [ 2.227109] ata7.00: configured for UDMA/33
    [ 2.373413] ata6: SATA link down (SStatus 0 SControl 300)
    [ 2.386722] ata9: SATA link down (SStatus 0 SControl 300)
    [ 2.386768] ata10: SATA link down (SStatus 0 SControl 300)
    [ 2.540027] ata3: softreset failed (device not ready)
    [ 2.540185] ata3: applying PMP SRST workaround and retrying
    [ 2.540217] ata5: softreset failed (device not ready)
    [ 2.540381] ata5: applying PMP SRST workaround and retrying
    [ 2.540408] ata4: softreset failed (device not ready)
    [ 2.540563] ata4: applying PMP SRST workaround and retrying
    [ 2.566689] usb 1-1: new low-speed USB device number 4 using ohci-pci
    [ 2.706711] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
    [ 2.706750] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 2.706786] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 2.707572] ata3.00: ATA-7: ST3200826AS, 3.03, max UDMA/133
    [ 2.707575] ata3.00: 390721968 sectors, multi 16: LBA48 NCQ (depth 31/32)
    [ 2.707578] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.708066] ata4.00: ATA-8: TOSHIBA DT01ACA200, MX4OABB0, max UDMA/133
    [ 2.708068] ata4.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
    [ 2.708070] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.708443] ata3.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.708445] ata3.00: configured for UDMA/133
    [ 2.708626] scsi 2:0:0:0: Direct-Access ATA ST3200826AS 3.03 PQ: 0 ANSI: 5
    [ 2.709433] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.709436] ata4.00: configured for UDMA/133
    [ 2.709543] scsi 3:0:0:0: Direct-Access ATA TOSHIBA DT01ACA2 MX4O PQ: 0 ANSI: 5
    [ 2.709897] sd 2:0:0:0: [sda] 390721968 512-byte logical blocks: (200 GB/186 GiB)
    [ 2.709940] sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
    [ 2.709942] sd 3:0:0:0: [sdb] 4096-byte physical blocks
    [ 2.710054] sd 2:0:0:0: [sda] Write Protect is off
    [ 2.710057] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
    [ 2.710081] sd 3:0:0:0: [sdb] Write Protect is off
    [ 2.710083] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
    [ 2.710108] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.710131] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.713184] ata5.00: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
    [ 2.713188] ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32), AA
    [ 2.713191] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.716937] sdb: sdb1
    [ 2.717244] sd 3:0:0:0: [sdb] Attached SCSI disk
    [ 2.719680] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 2.719683] ata5.00: configured for UDMA/133
    [ 2.719828] scsi 4:0:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
    [ 2.720076] sd 4:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
    [ 2.720133] sd 4:0:0:0: [sdc] Write Protect is off
    [ 2.720136] sd 4:0:0:0: [sdc] Mode Sense: 00 3a 00 00
    [ 2.720160] sd 4:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
    [ 2.721044] scsi 6:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4481B 1.04 PQ: 0 ANSI: 5
    [ 2.723354] sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
    [ 2.723359] cdrom: Uniform CD-ROM driver Revision: 3.20
    [ 2.723609] sr 6:0:0:0: Attached scsi CD-ROM sr0
    [ 2.726375] ata5.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
    [ 2.726661] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 2.726858] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 2.727057] ata5.00: failed command: READ FPDMA QUEUED
    [ 2.727277] ata5.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
    res 40/00:04:00:00:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 2.728116] ata5.00: status: { DRDY }
    [ 2.728231] ata5: hard resetting link
    [ 2.736521] sda: sda1 sda2 < sda5 >
    [ 2.736973] sd 2:0:0:0: [sda] Attached SCSI disk
    [ 2.744047] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:13.0/usb1/1-1/1-1:1.0/input/input1
    [ 2.744380] hid-generic 0003:0518:0001.0001: input,hidraw0: USB HID v1.10 Keyboard [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:13.0-1/input0
    [ 2.744812] input: Plus More Enterprise LTD. USB-compliant keyboard as /devices/pci0000:00/0000:00:13.0/usb1/1-1/1-1:1.1/input/input2
    [ 2.745088] hid-generic 0003:0518:0001.0002: input,hidraw1: USB HID v1.10 Mouse [Plus More Enterprise LTD. USB-compliant keyboard] on usb-0000:00:13.0-1/input1
    [ 2.990025] usb 1-2: new low-speed USB device number 5 using ohci-pci
    [ 3.156230] input: Microsoft Microsoft 3-Button Mouse with IntelliEye(TM) as /devices/pci0000:00/0000:00:13.0/usb1/1-2/1-2:1.0/input/input3
    [ 3.156413] hid-generic 0003:045E:0040.0003: input,hidraw2: USB HID v1.10 Mouse [Microsoft Microsoft 3-Button Mouse with IntelliEye(TM)] on usb-0000:00:13.0-2/input0
    [ 3.213356] ata5: softreset failed (device not ready)
    [ 3.213519] ata5: applying PMP SRST workaround and retrying
    [ 3.380031] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 3.386448] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 3.392796] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x100)
    [ 3.392798] ata5.00: revalidation failed (errno=-5)
    [ 8.380028] ata5: hard resetting link
    [ 8.866697] ata5: softreset failed (device not ready)
    [ 8.866861] ata5: applying PMP SRST workaround and retrying
    [ 9.033366] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 9.039792] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 9.046258] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 9.046260] ata5.00: configured for UDMA/133
    [ 9.046276] ata5: EH complete
    [ 9.052053] sdc: sdc1
    [ 9.052397] sdc: detected capacity change from 0 to 1000204886016
    [ 9.052488] sd 4:0:0:0: [sdc] Attached SCSI disk
    [ 9.102207] ata5.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
    [ 9.102441] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 9.102622] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 9.102820] ata5.00: failed command: READ FPDMA QUEUED
    [ 9.102979] ata5.00: cmd 60/08:00:a8:6c:70/00:00:74:00:00/40 tag 0 ncq 4096 in
    res 40/00:04:a8:6c:70/00:00:74:00:00/40 Emask 0x50 (ATA bus error)
    [ 9.103442] ata5.00: status: { DRDY }
    [ 9.103556] ata5: hard resetting link
    [ 9.590022] ata5: softreset failed (device not ready)
    [ 9.590182] ata5: applying PMP SRST workaround and retrying
    [ 9.756697] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 9.763109] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 9.769456] ata5.00: failed to IDENTIFY (I/O error, err_mask=0x100)
    [ 9.769458] ata5.00: revalidation failed (errno=-5)
    [ 9.969270] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
    [ 14.756687] ata5: hard resetting link
    [ 15.243350] ata5: softreset failed (device not ready)
    [ 15.247493] ata5: applying PMP SRST workaround and retrying
    [ 15.413369] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 15.419789] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 15.426253] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 15.426255] ata5.00: configured for UDMA/133
    [ 15.426271] ata5: EH complete
    [ 15.457509] ata5.00: exception Emask 0x50 SAct 0x1 SErr 0x680900 action 0x6 frozen
    [ 15.466153] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 15.470623] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 15.475077] ata5.00: failed command: READ FPDMA QUEUED
    [ 15.479477] ata5.00: cmd 60/08:00:f8:69:70/00:00:74:00:00/40 tag 0 ncq 4096 in
    res 40/00:04:f8:69:70/00:00:74:00:00/40 Emask 0x50 (ATA bus error)
    [ 15.497016] ata5.00: status: { DRDY }
    [ 15.501349] ata5: hard resetting link
    [ 15.986684] ata5: softreset failed (device not ready)
    [ 15.990999] ata5: applying PMP SRST workaround and retrying
    [ 16.156695] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 16.163100] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.169558] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.169560] ata5.00: configured for UDMA/133
    [ 16.169567] ata5: EH complete
    [ 16.230439] ata5: limiting SATA link speed to 1.5 Gbps
    [ 16.230445] ata5.00: exception Emask 0x50 SAct 0x1c SErr 0x680900 action 0x6 frozen
    [ 16.239215] ata5.00: irq_stat 0x08000000, interface fatal error
    [ 16.243744] ata5: SError: { UnrecovData HostInt 10B8B BadCRC Handshk }
    [ 16.248330] ata5.00: failed command: READ FPDMA QUEUED
    [ 16.252861] ata5.00: cmd 60/38:10:40:00:00/00:00:00:00:00/40 tag 2 ncq 28672 in
    res 40/00:24:78:01:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 16.270799] ata5.00: status: { DRDY }
    [ 16.275275] ata5.00: failed command: READ FPDMA QUEUED
    [ 16.279713] ata5.00: cmd 60/f8:18:80:00:00/00:00:00:00:00/40 tag 3 ncq 126976 in
    res 40/00:24:78:01:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 16.297504] ata5.00: status: { DRDY }
    [ 16.302022] ata5.00: failed command: READ FPDMA QUEUED
    [ 16.306524] ata5.00: cmd 60/88:20:78:01:00/00:00:00:00:00/40 tag 4 ncq 69632 in
    res 40/00:24:78:01:00/00:00:00:00:00/40 Emask 0x50 (ATA bus error)
    [ 16.324306] ata5.00: status: { DRDY }
    [ 16.328707] ata5: hard resetting link
    [ 16.813352] ata5: softreset failed (device not ready)
    [ 16.817758] ata5: applying PMP SRST workaround and retrying
    [ 16.983368] ata5: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
    [ 16.989783] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.996261] ata5.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 16.996263] ata5.00: configured for UDMA/133
    [ 16.996279] ata5: EH complete
    [ 17.672607] systemd[1]: systemd 208 running in system mode. (+PAM -LIBWRAP -AUDIT -SELINUX -IMA -SYSVINIT +LIBCRYPTSETUP +GCRYPT +ACL +XZ)
    [ 17.677851] systemd[1]: Set hostname to <ROTATION-STATION>.
    [ 18.109971] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 18.109984] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory.
    [ 18.110330] systemd[1]: Starting Forward Password Requests to Wall Directory Watch.
    [ 18.110410] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
    [ 18.110428] systemd[1]: Expecting device sys-subsystem-net-devices-enp2s0.device...
    [ 18.110443] systemd[1]: Starting Remote File Systems.
    [ 18.110456] systemd[1]: Reached target Remote File Systems.
    [ 18.110468] systemd[1]: Starting Delayed Shutdown Socket.
    [ 18.110505] systemd[1]: Listening on Delayed Shutdown Socket.
    [ 18.110517] systemd[1]: Starting LVM2 metadata daemon socket.
    [ 18.110546] systemd[1]: Listening on LVM2 metadata daemon socket.
    [ 18.110558] systemd[1]: Starting /dev/initctl Compatibility Named Pipe.
    [ 18.110583] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
    [ 18.110595] systemd[1]: Starting Device-mapper event daemon FIFOs.
    [ 18.110624] systemd[1]: Listening on Device-mapper event daemon FIFOs.
    [ 18.110638] systemd[1]: Starting Encrypted Volumes.
    [ 18.110651] systemd[1]: Reached target Encrypted Volumes.
    [ 18.110664] systemd[1]: Starting Journal Socket.
    [ 18.110711] systemd[1]: Listening on Journal Socket.
    [ 18.110728] systemd[1]: Starting Setup Virtual Console...
    [ 18.138476] systemd[1]: Starting Create list of required static device nodes for the current kernel...
    [ 18.139007] systemd[1]: Mounting Huge Pages File System...
    [ 18.139550] systemd[1]: Starting Journal Service...
    [ 18.140217] systemd[1]: Started Journal Service.
    [ 18.406055] systemd-journald[127]: Vacuuming done, freed 0 bytes
    [ 18.685974] EXT4-fs (sda1): re-mounted. Opts: data=ordered
    [ 18.806623] systemd-udevd[155]: starting version 208
    [ 19.322248] parport_pc 00:0a: reported by Plug and Play ACPI
    [ 19.322309] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    [ 19.331550] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input4
    [ 19.331559] ACPI: Power Button [PWRB]
    [ 19.331882] ACPI: Fan [FAN] (on)
    [ 19.332660] ACPI: [Package] has zero elements (ffff8800bf306e80)
    [ 19.337757] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
    [ 19.337764] ACPI: Power Button [PWRF]
    [ 19.337878] ACPI: Invalid passive threshold
    [ 19.338149] thermal LNXTHERM:00: registered as thermal_zone0
    [ 19.338151] ACPI: Thermal Zone [THRM] (40 C)
    [ 19.387889] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
    [ 19.388553] wmi: Mapper loaded
    [ 19.549117] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \SOR2 1 (20130725/utaddress-251)
    [ 19.549126] ACPI Warning: 0x0000000000000b00-0x0000000000000b07 SystemIO conflicts with Region \SOR1 2 (20130725/utaddress-251)
    [ 19.549131] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
    [ 19.717185] MCE: In-kernel MCE decoding enabled.
    [ 19.733875] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141
    [ 19.746781] input: PC Speaker as /devices/platform/pcspkr/input/input6
    [ 19.780737] [drm] Initialized drm 1.1.0 20060810
    [ 19.801750] EDAC MC: Ver: 3.0.0
    [ 19.808239] sky2: driver version 1.30
    [ 19.808388] sky2 0000:02:00.0: Yukon-2 EC Ultra chip revision 5
    [ 19.808451] sky2 0000:02:00.0: irq 43 for MSI/MSI-X
    [ 19.808698] sky2 0000:02:00.0 eth0: addr 00:30:18:a6:19:e3
    [ 19.835294] snd_hda_intel 0000:00:14.2: irq 44 for MSI/MSI-X
    [ 19.870517] AMD64 EDAC driver v3.4.0
    [ 19.895226] microcode: AMD CPU family 0xf not supported
    [ 19.929703] systemd-udevd[156]: renamed network interface eth0 to enp2s0
    [ 20.021077] kvm: Nested Virtualization enabled
    [ 20.073770] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
    [Firmware Bug]: powernow-k8: First, make sure Cool'N'Quiet is enabled in the BIOS.
    [Firmware Bug]: powernow-k8: If that doesn't help, try upgrading your BIOS.
    [ 20.088804] checking generic (f9000000 130000) vs hw (d0000000 10000000)
    [ 20.088805] checking generic (f9000000 130000) vs hw (f8000000 2000000)
    [ 20.088806] fb: conflicting fb hw usage nouveaufb vs VESA VGA - removing generic driver
    [ 20.100569] Console: switching to colour dummy device 80x25
    [ 20.101154] [drm] hdmi device not found 1 0 1
    [ 20.101224] nouveau [ DEVICE][0000:01:00.0] BOOT0 : 0x086c00a2
    [ 20.101227] nouveau [ DEVICE][0000:01:00.0] Chipset: G86 (NV86)
    [ 20.101229] nouveau [ DEVICE][0000:01:00.0] Family : NV50
    [ 20.101830] nouveau [ VBIOS][0000:01:00.0] checking PRAMIN for image...
    [ 20.113952] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.
    [Firmware Bug]: powernow-k8: First, make sure Cool'N'Quiet is enabled in the BIOS.
    [Firmware Bug]: powernow-k8: If that doesn't help, try upgrading your BIOS.
    [ 20.157989] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05
    [ 20.158048] sp5100_tco: PCI Revision ID: 0x13
    [ 20.158077] sp5100_tco: failed to find MMIO address, giving up.
    [ 20.162297] nouveau [ VBIOS][0000:01:00.0] ... appears to be valid
    [ 20.162300] nouveau [ VBIOS][0000:01:00.0] using image from PRAMIN
    [ 20.162421] nouveau [ VBIOS][0000:01:00.0] BIT signature found
    [ 20.162424] nouveau [ VBIOS][0000:01:00.0] version 60.86.65.00.51
    [ 20.182582] nouveau [ PFB][0000:01:00.0] RAM type: DDR2
    [ 20.182585] nouveau [ PFB][0000:01:00.0] RAM size: 512 MiB
    [ 20.182586] nouveau [ PFB][0000:01:00.0] ZCOMP: 1292 tags
    [ 20.204429] nouveau [ PTHERM][0000:01:00.0] FAN control: none / external
    [ 20.204439] nouveau [ PTHERM][0000:01:00.0] fan management: disabled
    [ 20.204442] nouveau [ PTHERM][0000:01:00.0] internal sensor: yes
    [ 20.204613] [TTM] Zone kernel: Available graphics memory: 2026408 kiB
    [ 20.204615] [TTM] Initializing pool allocator
    [ 20.204619] [TTM] Initializing DMA pool allocator
    [ 20.204630] nouveau [ DRM] VRAM: 512 MiB
    [ 20.204632] nouveau [ DRM] GART: 1048576 MiB
    [ 20.204636] nouveau [ DRM] TMDS table version 2.0
    [ 20.204638] nouveau [ DRM] DCB version 4.0
    [ 20.204641] nouveau [ DRM] DCB outp 00: 01000302 00020030
    [ 20.204644] nouveau [ DRM] DCB outp 01: 02000300 00020028
    [ 20.204646] nouveau [ DRM] DCB outp 02: 02011312 00020030
    [ 20.204648] nouveau [ DRM] DCB outp 03: 04011310 00c0c028
    [ 20.204650] nouveau [ DRM] DCB outp 04: 010223f1 00c0c080
    [ 20.204652] nouveau [ DRM] DCB conn 00: 2030
    [ 20.204655] nouveau [ DRM] DCB conn 01: 1130
    [ 20.204657] nouveau [ DRM] DCB conn 02: 0210
    [ 20.204659] nouveau [ DRM] DCB conn 03: 0211
    [ 20.204660] nouveau [ DRM] DCB conn 04: 0213
    [ 20.210863] nouveau W[ DRM] failed to create encoder 0/1/0: -19
    [ 20.210865] nouveau W[ DRM] TV-1 has no encoders, removing
    [ 20.210895] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
    [ 20.210897] [drm] No driver support for vblank timestamp query.
    [ 20.211027] nouveau [ DRM] 1 available performance level(s)
    [ 20.211031] nouveau [ DRM] 0: core 500MHz shader 1250MHz memory 400MHz fanspeed 100%
    [ 20.211033] nouveau [ DRM] c: core 459MHz shader 918MHz memory 399MHz voltage 1320mV
    [ 20.214375] ppdev: user-space parallel port driver
    [ 20.218673] nouveau [ DRM] MM: using CRYPT for buffer copies
    [ 20.270146] input: HDA ATI SB Front Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input14
    [ 20.276729] input: HDA ATI SB Headphone as /devices/pci0000:00/0000:00:14.2/sound/card0/input13
    [ 20.276801] input: HDA ATI SB Line Out CLFE as /devices/pci0000:00/0000:00:14.2/sound/card0/input12
    [ 20.276871] input: HDA ATI SB Line Out Surround as /devices/pci0000:00/0000:00:14.2/sound/card0/input11
    [ 20.276937] input: HDA ATI SB Line Out Front as /devices/pci0000:00/0000:00:14.2/sound/card0/input10
    [ 20.277003] input: HDA ATI SB Line as /devices/pci0000:00/0000:00:14.2/sound/card0/input9
    [ 20.277072] input: HDA ATI SB Rear Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input8
    [ 20.277146] input: HDA ATI SB Front Mic as /devices/pci0000:00/0000:00:14.2/sound/card0/input7
    [ 20.288590] nouveau [ DRM] allocated 1680x1050 fb: 0x70000, bo ffff88013974c000
    [ 20.288622] EDAC amd64: DRAM ECC disabled.
    [ 20.288629] EDAC amd64: ECC disabled in the BIOS or no ECC capability, module will not load.
    Either enable ECC checking or force module loading by setting 'ecc_enable_override'.
    (Note that use of the override may cause unknown side effects.)
    [ 20.288675] fbcon: nouveaufb (fb0) is primary device
    [ 20.376049] Console: switching to colour frame buffer device 128x48
    [ 20.376338] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device
    [ 20.376340] nouveau 0000:01:00.0: registered panic notifier
    [ 20.376346] [drm] Initialized nouveau 1.1.1 20120801 for 0000:01:00.0 on minor 0
    [ 20.568688] Adding 2500432k swap on /dev/sda5. Priority:-1 extents:1 across:2500432k FS
    [ 20.811563] EXT4-fs (sdb1): mounted filesystem with ordered data mode. Opts: data=ordered
    [ 20.855298] systemd-journald[127]: Received request to flush runtime journal from PID 1
    [ 22.153827] sky2 0000:02:00.0 enp2s0: enabling interface
    [ 22.153887] IPv6: ADDRCONF(NETDEV_UP): enp2s0: link is not ready
    [ 24.883373] sky2 0000:02:00.0 enp2s0: Link is up at 1000 Mbps, full duplex, flow control both
    [ 24.883402] IPv6: ADDRCONF(NETDEV_CHANGE): enp2s0: link becomes ready
    [ 102.400031] ata4.00: exception Emask 0x0 SAct 0x2 SErr 0x0 action 0x6 frozen
    [ 102.400038] ata4.00: failed command: READ FPDMA QUEUED
    [ 102.400044] ata4.00: cmd 60/c8:08:40:0e:00/00:00:94:00:00/40 tag 1 ncq 102400 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 102.400046] ata4.00: status: { DRDY }
    [ 102.400051] ata4: hard resetting link
    [ 102.933349] ata4: softreset failed (device not ready)
    [ 102.933356] ata4: applying PMP SRST workaround and retrying
    [ 103.100029] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
    [ 103.101156] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 103.102323] ata4.00: SB600 AHCI: limiting to 255 sectors per cmd
    [ 103.102326] ata4.00: configured for UDMA/133
    [ 103.102330] ata4.00: device reported invalid CHS sector 0
    [ 103.102340] sd 3:0:0:0: [sdb]
    [ 103.102342] Result: hostbyte=0x00 driverbyte=0x08
    [ 103.102344] sd 3:0:0:0: [sdb]
    [ 103.102345] Sense Key : 0xb [current] [descriptor]
    [ 103.102348] Descriptor sense data with sense descriptors (in hex):
    [ 103.102349] 72 0b 00 00 00 00 00 0c 00 0a 80 00 00 00 00 00
    [ 103.102355] 00 00 00 00
    [ 103.102358] sd 3:0:0:0: [sdb]
    [ 103.102359] ASC=0x0 ASCQ=0x0
    [ 103.102361] sd 3:0:0:0: [sdb] CDB:
    [ 103.102363] cdb[0]=0x28: 28 00 94 00 0e 40 00 00 c8 00
    [ 103.102369] end_request: I/O error, dev sdb, sector 2483031616
    [ 103.102415] ata4: EH complete
    [ 103.157724] EXT4-fs error (device sdb1): __ext4_get_inode_loc:3917: inode #77597314: block 310378696: comm Plex Media Serv: unable to read itable block
    [ 133.386698] ata4.00: exception Emask 0x0 SAct 0x1ffffe0 SErr 0x0 action 0x6 frozen
    [ 133.386706] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386711] ata4.00: cmd 60/08:28:70:0e:00/00:00:94:00:00/40 tag 5 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386714] ata4.00: status: { DRDY }
    [ 133.386716] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386721] ata4.00: cmd 60/08:30:78:0e:00/00:00:94:00:00/40 tag 6 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386723] ata4.00: status: { DRDY }
    [ 133.386725] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386729] ata4.00: cmd 60/08:38:80:0e:00/00:00:94:00:00/40 tag 7 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386731] ata4.00: status: { DRDY }
    [ 133.386733] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386738] ata4.00: cmd 60/08:40:88:0e:00/00:00:94:00:00/40 tag 8 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386740] ata4.00: status: { DRDY }
    [ 133.386742] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386746] ata4.00: cmd 60/08:48:90:0e:00/00:00:94:00:00/40 tag 9 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386748] ata4.00: status: { DRDY }
    [ 133.386750] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386755] ata4.00: cmd 60/08:50:98:0e:00/00:00:94:00:00/40 tag 10 ncq 4096 in
    res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
    [ 133.386757] ata4.00: status: { DRDY }
    [ 133.386759] ata4.00: failed command: READ FPDMA QUEUED
    [ 133.386763] ata4.00: cmd 60/08:58:a0:0e:00/00:00:94:00:00/40 tag 11 ncq 4096 in
    res 40/00:00:00:00:00/00:00:

  • Pcipsy error while booting

    I have installed a PCI audio card and its driver. While booting
    I am getting following error
    pcipsy: WARNING: pcipsy0: ino 23 is invalid
    pcipsy: WARNING: pcipsy0: ino 10 is invalid
    Can any one tell me what is causing this pci error?
    Thanks

    The most likely causes of this error are:
    1) Failing to execute tmloadcf after updating the UBBCONFIG file.
    2) Failing to set TUXDIR correctly in the UBBCONFIG file.
    3) Failing to set TUXCONFIG, PATH, or
    LD_LIBRARY_PATH(Unix)/SHLIB_PATH(HP)/LIBPATH(AIX) correctly in your
    enviroment.when executing tmboot or tlisten.
    You should verify that your environment is set correctly and you should
    execute tmunloadcf to see the contents of the configuration file that has
    been loaded.
    Ed
    <Kaustubh Deoghare> wrote in message news:[email protected]..
    Hello,
    I am getting following error while booting tuxedo
    exec TMS_ORACLE8I -A :
    TMS_ORACLE8I: symbol lookup error: TMS_ORACLE8I: undefined symbol:
    kgsmp789_compat_
    CMDTUX_CAT:819: INFO: Process id=2568 Assume started (pipe).
    Though I have installed Oracle9i, in ubbconfig it is still taking
    TMS_ORACLE8I and hence trying to access Oracle8i library files.
    Pl suggest in this regard
    Thanx in advance

  • BootCamp 5.0 error on 13" MacBook Pro Mid-2010: "Installation Error. Boot Camp x64 is unsupported on this computer model"

    Installing Boot Camp 5.0.5033 (downloadable at http://support.apple.com/kb/DL1638) on Windows 8 x64 on 13” MacBook Pro Mid-2010 using BootCamp\setup.exe, I get the following message: “Installation Error. Boot Camp x64 is unsupported on this computer model”.
    According to http://support.apple.com/kb/HT5634, Windows 8 x64 is not supported by Boot Camp 5 on 13” MacBook Pro Mid-2010 .
    Previous version, Boot Camp 4.0, causes bluescreens on Windows 8 (https://discussions.apple.com/message/20131524#20131524).
    Fortunately, it might be still possible to employ updated Boot Camp by launching “msiexec /i BootCamp.msi” from BootCamp\Drivers\Apple folder using administrative command prompt (http://technet.microsoft.com/en-us/library/cc947813%28v=WS.10%29.aspx).
    However, new Boot Camp 5.0.5033 does not contain all the drivers for 13” MacBook Pro Mid-2010. E.g. driver for NVIDIA nForce System Management Controller (labeled Other devices/Coprocessor in Control Panel) and NVIDIA nForce PCI Systems Management (labeled Other devices/SM Bus Controller in Control Panel) must be obtained at Drivers\NVidia\NVidiaChipset64 in older Boot Camp 4.0 (downloadable at http://support.apple.com/kb/DL1634)
    According to Microsoft (http://windows.microsoft.com/en-US/windows-8/system-requirements), the MacBook Pro config (Intel Core 2 Duo P8600 2.4GHz, 4GB RAM) exceeds Windows 8 x64 hardware requirements. Windows Experience Index for this laptop is approx. 5.1 (http://windows.microsoft.com/en-US/windows-8/what-windows-experience-index).
    Does anybody know, is there any technical reason why Windows 8 x64 is not supported by Boot Camp 5 on 13” MBP Mid-2010?
    Is there a specific hardware/firmware deficiency in this MacBook model, incompatible with Win8? Maybe NVIDIA refused to provide Win8-compatible drivers for its chipset components (GeForce 320M graphics card though is still supported by latest notebook drivers available at www.geforce.com)?

    Thanks for the detailed explanation! If MacBook supports AHCI/SATA only in native “UEFI mode”, while reverting back to PATA/IDE in legacy “BIOS mode”, then it could make perfect sense to use UEFI to make sure that technology like Native Command Queuing (NCQ) is employed, as it may give noticeable performance improvements for certain operations: www.happysysadm.com/2012/12/intel-g530-nas-performance-part-3.html. I wonder how do you get Windows 8 x64 with EFI bootloader installed on MacBook?
    Simply choosing EFI Boot (“Some EFI platforms support both UEFI and BIOS firmware. On some of those systems, it is not always clear if the default DVD boot option is an EFI or BIOS boot option. On these systems, using the EFI shell command may be required. If you do not specifically start Windows Setup by using the EFI boot entry, the default firmware boot entry for BIOS may be used. If Windows Setup starts in BIOS mode on a combined EFI/BIOS system, the ESP and MSR partitions are not created.”) from Win8 x64 DVD when installing on blank HDD would yield “The computer restarted unexpectedly or encountered an unexpected error. Windows installation cannot proceed" message. Also, if the hard drive was not in SATA mode during Windows installation, registry tweaking may be required before switching from PATA to SATA. Do you do registry tweaking and EFI bootloader configuration manually after a copy of Windows was installed in its dedicated partition in a regular way?

  • Built-In Keyboard Firmware Update 1.0 fails with error 23:3 on MacBook 2,1

    I attempted to install "Built-In Keyboard Firmware Update 1.0" on two laptops tonight.
    Macbook Pro 3,1:
    Hadn't experienced the issue that the firmware would resolve. Installed the update anyway, successfully, and continued to have no problems since.
    Macbook 2,1:
    Hadn't experienced the issue that the firmware would resolve. Tried to install the update, but it failed with error "23:3". After the failure, the keyboard was non-responsive for about 30-60 seconds, during which time I assume it restored/re"booted" itself. Keyboard function was restored automatically after this time, though there was no indication that it would return, and I had to suffer a minor sweat. Still, I didn't learn I power cycled the system and tried again, but the update never installed successfully.
    Lessons learned -
    If it ain't broken...
    That said, Apple seems to have designed their hardware well enough to be able to recover from a failed firmware update. In this case, you just have to pray a little until the keyboard responds again.
    Apple: be so kind, let us know what 23:3 means, and if needed, update the Firmware Updater.
    //

    Hi,
    I was just wondering how you were able to get the macbook to accept the update? I had to take mine to apple store and get entire keyboard and trackpad replaced in my macbook. They then told me to ignore the update cause they did not have any other keyboards to replace if it happened again.

Maybe you are looking for

  • USB MIDI devices not detected under OS 10.5.2

    Leopard's Audio Midi Configuration doesn't detect my Korg microKontrol, Novation Remote Zero SL and my Evolution MK-249C2 MIDI keyboard. Firewire MIDI device is detected (RME fireface 800). Using the "latest" drivers - Novation Automap Universal 2.0.

  • Multiple tasks with daqmx

    Hello, I am currently working on a Senior Design Project where I have to measure torque, RPM, pressure and temperature.  I am using strain gages, a Hall Effect Sensor, pressure sensor and thermocouples to obtain these readings.  A myDAQ collects the

  • What is Condé Nast At Home?

    Condé Nast At Home has a collection of scheduled content applications that deliver a wide variety of printables directly to your printer, when you want them. Epicurious – Daily Recipes Epicurious – Healthy Dinner Tonight Epicurious – Lunch Ideas for

  • Workitem execution from outlook - via citrix

    Hallo, we access SAP via Citrix and we want to execute workitems from outlook (by a decision task). I use the report RSWUWFML2, the user receives e-mail with corresponding attachments to execute the workitem, but I don't know, how to open them. Do I

  • Library & Vault significantly different sizes

    My library is 678 gigs. My vault for that library is only 556 gigs. And all is up-to-date. I know they should be a different size, but more than 100 gigs worth? I have never seen this before. Anyone else?