Upgrade AP1262N to LAP1262 autonomous to lightweight

                   Hi,
This is one of our first site where we are implementing Cisco wireless, and we bought some external Autonomous AP1262, when we should have bought Lightweight LAP1262 . We can get those replaced, but I am looking into migrating them in order to get them to register with our 5508 controllers.
There do not seem to be a migration tool to download for 1262. Must it be done via the WCS ?
So far I have not managed to add these autonomous AP to the controllers.
Thanks to let me know if a migration toll exists for those !
Best Regards,
Gregory Gout

Use the archive command. You just need I download the rcv (recovery image) from CCO. Upgrade tool will not work and this is easy to do.
If you choose to overwrite the existing file, issue the archive download-sw /overwrite /reload tftp: //location/image-name command. The /overwrite option overwrites the software image in flash with the downloaded image. The /reload option reloads the system after you download the image unless the configuration is changed and not saved. For //location, specify the IP address of the TFTP server. For image name, specify the Cisco IOS filename that you plan to use to upgrade the access point. In this example, the command is archive download-sw /overwrite /reload tftp: //10.77.244.194/c1240-k9w7-tar.124-10b.JA3.tar. As mentioned earlier, do not change the name of the Cisco IOS file. Leave it as the default. You find these logs during the successful file transfer:
Sent from Cisco Technical Support iPhone App

Similar Messages

  • Upgrade 1120G from an autonomous to a lightweight accesspoint

    Hi!
    I have a network consisting of 22 autonomous Aironet 1120G accesspoints. Is it possible to upgarde these to lightweight accesspoints for using with a Cisco WLAN Controller?

    Hi Zach,
    These AP's can be converted to LWAPP. We did this exact conversion last summer on about 30 1121G's with the LWAPP upgrade tool. Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
    Software release 4.0.155.0 New Features
    LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
    Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
    http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
    LWAPP Upgrade Tool Troubleshoot Tips
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
    Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
    System Requirements
    You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
    **All 1100 series access points containing MP21G (802.11g) radios
    All 1130, 1230, and 1240 series access points
    All modular 1200 series access points running Cisco IOS software and containing these supported radios:
    802.11g: MP21G, MP31G
    802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
    All 1300 series access points in access point mode
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
    Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
    The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
    Cisco Aironet 1240AG Series access points
    Cisco Aironet 1230AG Series access points
    Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
    Cisco Aironet 1130AG Series access points
    **Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
    Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
    The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
    Cisco Aironet Access Point Support for Lightweight Access Point Protocol
    http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
    Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
    Hope this helps!
    Rob

  • Autonomous To Lightweight Mode Upgrade Image 1042

    Hi,
    I have two AP1042 that I want to convert to lightweight, but I'm not able to find the software for that. I can only find the IOS software. Is it possible to convert? Is it located some other place?
    Regards,
    Patrick

    Vikas,
    You can convert any of these AP's from autonomous to lightweight and vice versa.  The requirement is that you need to be able to download the image.  If you have the support to download, then you can follow one of these instructions:
    Using a TFTP Server to Return to a Previous Release
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    https://supportforums.cisco.com/docs/DOC-18268
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    http://www.youtube.com/watch?v=QQ_NuxdRhQ4
    https://supportforums.cisco.com/docs/DOC-14960
    Please rate helpful post and Cisco Support Community will donate to Kiva
    Scotty

  • Error when migrating AP 2600 from Autonomous to Lightweight

    Hello,
    I am trying to migrating AP 2600 series that came with autonomous image 15.2 to lightweight using the Cisco Prime Infrastructure built-in migration template.
    The AP successfully downloads the image from an external TFTP server but fails at updating the environment variables.
    The logs show that the AP should download a text file from Cisco Prime but fails to do so:
    START: Detailed logging started at -> 01.22.2014_14.01.52
    INFO: TELNET to device 10.32.148.225 done.
    INFO: Privilege level is equal to 15.
    INFO: Setting vty line completed.
    INFO: Dumped Environmental variables.
    INFO: AP is supported for Upgrade process
    INFO: IOS version is greater than or equal to 12.3(7)JA.
    INFO: AP has MIC installed already.
    INFO: Station role is root.
    INFO: Station role is root.
    INFO: DNS and Domain name configured.
    INFO: Mac address of device is 88:5a:92:17:2b:09
    INFO: Completed Dot11Radio0 shutting.
    INFO: Device set up done and time configured on device.
    INFO: Run-config dumped.
    INFO: AP is DHCP configured.
    INFO: Hostname gbknwa2225sr
    INFO: Dumped Environmental variables.
    INFO: Starts loading recovery image, takes time based on link speed.
    INFO: Image Loading done.
    INFO: Copying updated Env. variable file to WCS local tftp server 10.70.165.165
    INFO: Copying the Env. variable file from tftp server to device.
    Copying the Env vars to device failed.
    ERROR: Device Response ::
    copy tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt flash:/env_vars
    Destination filename [env_vars]?
    %Warning:There is a file already existing with this name
    Do you want to over write? [confirm]
    Accessing tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt...
    %Error opening tftp://10.70.165.165/Env_vars_10.32.148.225_01.22.2014_14.07.55.txt (Timed out)
    gbknwa2225sr#
    gbknwa2225sr#_tune_                 
    gbknwa2225sr#
    INFO: Un-shut radio 1 done.
    END: Migration Process Failure: Copying Env_Vars to device failed.
    What can I do to solve that ?
    Many thanks for your help,
    David

    Hi David,
    I think 2600 AP not supported on Prime Infra for autonomous to Ligtweight migration.
    PI 1.2, 1.3, 1.4 , 2.0
    Only these APs are supported: Autonomous to Lightweight Migration Support
    Cisco Aironet 1130 Access Point
    Cisco Aironet 1200 Access Point
    Cisco Aironet 1240 Access Point
    Cisco Aironet 1310 Bridge
    Cisco Aironet 1410 Bridge
    Check this link:
    http://www.cisco.com/en/US/docs/wireless/prime_infrastructure/1.4/configuration/guide/ctrlcfg.html
    Hope it helps.
    Regards
    Dont forget to rate helpful posts

  • AP1231 from autonomous to lightweight

    Hi Community.
    Is it possible to upgarde the AP1231 from autonomous to lightweight.
    Kind regards patrick

    Here are links to the conversion
    Using a TFTP Server to Return to a Previous Release
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    https://supportforums.cisco.com/docs/DOC-18268
    http://www.cisco.com/en/US/docs/wireless/access_point/conversion/lwapp/upgrade/guide/lwapnote.html#wp160918
    http://www.youtube.com/watch?v=QQ_NuxdRhQ4
    https://supportforums.cisco.com/docs/DOC-14960
    Sent from Cisco Technical Support iPhone App

  • How to upgrade an Aironet 3602e from Autonomous to Lightweight???

    Hi everyone
    Hope you can help me with this. I have an Aironet 3602e that was bought as a Lightweight AP, last week need to do some testing and changed the image to an Autonomous one. Now I need to use it with a Controller, but can´t find the procedure to upgrade it to Lightweight again.
    I tried the procedure of the upgrade tool, but it saids that this AP is nos supported.
    Anyone who has this information please. I already had the Lightweight images.
    Best Regards
    Alvaro Rugama

    HI Alvaro,
    For the LWAP conversion, use the recovery image. We can use this command on the autonomous AP priviledge mode.
    AP#archive download-sw /force-reload /overwrite tftp://10.10.10.1/image.tar
    Regards
    Hope it helps.

  • Upgrade autonomous to lightweight using tftp

    Hello,
    I'm have new autonomous 1242 AP without any configuration. Can I convert it to lightweight using tftp? Which image should I use.
    The current version is 12.3(7)JA5.
    Many thanks in advance.
    Rgds,
    Fauzan

    Hi Mohd,
    yes u can directly convert it to LWAPP image.. go for the latest LWAPP that we have for that product.. the below doc may help u as well!!
    https://supportforums.cisco.com/docs/DOC-14960
    Please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Autonomous To Lightweight Mode Upgrade Image

    Where can I download this image for AP 1240 in cisco web site. I have CCO.

    Hi Victor,
    It should have been where Andrew pointed you to (who knows :) it is available via this link;
    12.3(11)JX1 LWAPP Recovery Image
    http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=12.3.11-JX1&mdfid=280237322&sftType=IOS%20Software&optPlat=null&nodecount=12&edesignator=ED&modelName=Cisco%20Aironet%201240%20AG%20Access%20Point&treeMdfId=278875243&modifmdfid=null&imname=null&treeName=Wireless&hybrid=Y&imst=N
    Hope this helps!
    Rob

  • Wireless AP 1041 Autonomous to Lightweight

    Is it possible to convert a 1041 in Autonomous AP mode to Lightweight? Since on the cco page there is no upgrade tool under the 1040 series AP,
    and also i didnt find any document with the procedure.
    Thanks in advace.
    Nuno

    Yes,
    Here
    https://supportforums.cisco.com/thread/2065677

  • Convert Autonomous to lightweight AP - Static IP Address

    Hi,
    I've converted a couple of Autonomous APs to lightweight recently and once they reboot they have a static IP configured on them, which then requires console access to remove the static IP.
    Below are the commands I run to convert the AP:
    AP#archive tar /xtract ftp://username:password@FTP Server IP/ap1g2-rcvk9w8-tar.152-2.JB3.tar flash:/
    AP(config)#boot system flash:/filename
    AP#copy run start
    Is there something I'm missing in my process which will prevent the AP from having a static IP address when it reboots and loads the lightweight image?
    Thanks,

    AP#copy run start
    Instead of saving the config, you need to delete the config using the command "wr default". 

  • 3700 AP - Best way to convert back from Autonomous to LIghtweight

    I have a 3700 AP that I have up & running as Autonomous. I recently got a 2504 WLC and would like to put the AP back to Lightweight and run it from the 2504.  
    The 2504 is running 8.0.110.0 code and I have the current 3700 Lightweight Recovery image and IOS downloaded as well. 
    I have done done some searches and most of he articles are conversion to Autonomous. Not much is out there for putting it back. Some articles just mention needing the Lightweight  recovery image while others state I can use the Mode button and just have a TFTP server running  in a specific subnet and the AP will "pull" down the code and convert back.  Almost all of the articles refer to old model APs...
    Looking for clarity in the process as I certainly don't want to brick this 3700 AP. 
    Thx. 

    Hi
    You can use either methods & it will work (even for 3700)
    If you using mode button method, make sure you rename the recovery image something like this ap3g2-k9w7-tar.default. Refer this post for detail
    http://mrncciew.com/2013/12/13/ap-conversion-using-mode-button/
    Normal method is described here
    http://mrncciew.com/2012/10/20/lightweight-to-autonomous-conversion/
    HTH
    Rasika
    **** Pls rate all useful responses ****

  • "Poor Signal", "Coverage hole pre alarm for client" after changing from Autonomous to Lightweight infrastruture

    Dears,
    I use to have wireless infrastructure based on autonomous APs 1142n, auth w/ 802.1x and everything was fine.
    My Company decided to implement WLC 5508, and I changed only 2nd floor (2 APs) as lightweight and implement WLC over there as pilot testing...
    Now All persons here (around 35 clients) are complaining about disconnections, poor signal...
    Both APs are distant each other maximim of 15 meters... Our office has a medium open spaced room, with (20 X 15 meters) only 2 "Pilaster" in the middle of the room.
    I am facing this message at WLC logs
    Thu Nov 1 16:03:57 2012
    Coverage hole pre alarm for client[1] 00:37:6d:eb:67:44 on 802.11a interface of AP 00:26:cb:4c:8e:b0 (AP01-RJOBTF). Hist: 1 0 3 4 1 1 2 7 2 9 10 13 4 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
    Thu Nov 1 15:55:21 2012
    Rogue AP : 7c:4f:b5:ed:27:a1 detected on Base Radio MAC : 1c:aa:07:6e:93:20 Interface no:0(802.11b/g) on Channel 11 with RSSI: -92 and SNR: 1 and Classification: unclassified
    Thu Nov 1 15:50:27 2012
    Coverage hole pre alarm for client[1] 28:e0:2c:6d:11:58 on 802.11b/g interface of AP 00:26:cb:4c:8e:b0 (AP01-RJOBTF). Hist: 0 0 2 5 11 16 9 2 5 12 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
    Is there any best practices I should perform over here ?
    Any specific configuration with the signal itself ? In my opinion we dont have a big room here .. 2 APs should work very well... but they are not...
    I also can see many Rogue APs... I am not sure if that rogues aps have anything to do with this problem.... also I didnt change anything at 3rd floor (not sure if the
    Thanks in advance!!!

    Actually I am using both APs as lightweight in 2nd floor.
    How about this power level? where I can find those parameters ?
    At 3rd floor all APs are autonomous, I accessed one of them and find this parameter
    CCK Transmitter Power (dBm):           Max
    OFDM Transmitter Power (dBm):           Max
    Client Power (dBm):                     Max
    is that the parameter you talked about ?
    At WLC I found this screen
    Tx Power Level Assignment Algorithm
    Power Level Assignment Method
    Automatic
    On Demand
    Fixed
                             1                         2                         3                         4                         5                    
    Maximum Power Level Assignment (-10 to 30 dBm)
    Minimum Power Level Assignment (-10 to 30 dBm)
    Power Assignment Leader
    Last Power Level Assignment
    Power Threshold (-80 to -50 dBm)
    Power Neighbor Count
    Should I check anything else ?
    Thanks in advance!!!

  • Converting a 1260AP from Autonomous to Lightweight mode

    Is the process for converting 1260 APs to lightweight mode any different from converting 1140s or 1250s? I've converted several APs to LWAP mode but this is my first 1260.  Four 1260s need to be converted.
    I have one in a remote location that seems to be comatose. Here are the steps I took to convert the AP.  Did skip/miss a step?
    1. uploaded code to the AP  ap3g1-rcvk9w8-tar.152-2.JB.tar
    2. configured the AP for DHCP. It successfully leased a DHCP address. Controller information is provided via DHCP Option 43.
    3. saved the configuration
    4. verified the code, successful
    5. disabled wireless radios
    6. installed the lightweight code using the command archive download-sw /safe flash:/ap3g1-rcvk9w8-tar.152-2.JB.tar
         The installation was successful
    7. rebooted the AP
    After that nothing. The AP has not leased another IP address. The switchport is active. The APs MAC address is registering in the switches MAC address table.  The AP is receiveing PoE from the switch. I noticed that this AP is only receiving 6.2W of power where the three are getting anywhere between 8.8W and 9.3W. I am unable to ping the old static IP of the AP too.
    Any suggestions?

    can you console into the AP and post it's boot up cycle?  Let it capture for two reboots of the AP.
    Can you also share the config of the switchport this AP is connected to?
    HTH,
    Steve
    Please remember to rate useful posts, and mark questions as answered

  • Upgrade 1121 autonomous to LWAPP

    I have some access-points AIR-AP-1121G-TO-K9 and it would like to use them with a WLAN Controller. Is possible to change IOS for the software LWAPP to use with the WLAN Controller?
    I know that that is possible in another models of access-points, but I don't know if the 1121 support that upgrade.
    Regards.

    Hi Andre,
    Just to add a note to the good tips from Ankur. These AP's can be converted to LWAPP. We did this exact conversion last summer on about 30 1121G's with the **LWAPP upgrade tool**.
    Support for the 1121 was added in WLC version 4.0.155.0 Have a look at these related docs;
    Software release 4.0.155.0 New Features
    LWAPP for Cisco Aironet 1100 Series Access Points (802.11g radio only) Allows the Cisco Aironet 1100 Series Access Point to be upgraded from autonomous access point mode to lightweight mode using the autonomous to lightweight mode upgrade tool.
    Note You must install software release 4.0.155.0 on the controller before connecting 1100 series access points to the controller.
    http://www.cisco.com/en/US/products/ps6366/prod_release_note09186a00806e8989.html#wp147320
    LWAPP Upgrade Tool Troubleshoot Tips
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a008072d9a1.shtml
    Access points must run Cisco IOS Release 12.3(7)JA or later before you use the upgrade tool.
    System Requirements
    You can use the Autonomous to Lightweight Mode upgrade tool to install Cisco IOS Release 12.3(11)JX on these access points:
    **All 1100 series access points containing MP21G (802.11g) radios
    All 1130, 1230, and 1240 series access points
    All modular 1200 series access points running Cisco IOS software and containing these supported radios:
    802.11g: MP21G, MP31G
    802.11a: AIR-RM21A-x-K9, AIR-RM22A-x-K9
    All 1300 series access points in access point mode
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
    Cisco has released a free tool called the "Autonomous to Lightweight Mode Upgrade Tool" that allows selected Cisco Aironet autonomous access point models to be configured for lightweight mode operation.
    The Autonomous to Lightweight Mode Upgrade Tool supports the following models:
    Cisco Aironet 1240AG Series access points
    Cisco Aironet 1230AG Series access points
    Cisco Aironet 1200 Series access points that contain 802.11g (AIR-MP21G-x-K9) and/or second-generation 802.11a radios (AIR-RM21A-x-K9 or AIR-RM22A-x-K9)
    Cisco Aironet 1130AG Series access points
    **Cisco Aironet 1100 Series Access Points that contain 802.11g radios (AIR-AP1121G-x-K9)
    Cisco Aironet 1300 Series Access Points/Bridges (AIR-BR1310G-x-K9 or AIR-BR1310G-x-K9-R). A Cisco Aironet 1300 Series operating in Lightweight Access Point Protocol (LWAPP) mode only operates as an access point. This series does not support LWAPP bridging mode.
    The Autonomous to Lightweight Mode Upgrade Tool supports a process to migrate an autonomous access point from autonomous mode to lightweight mode. Unlike a VxWorks to Cisco IOS Software upgrade, this process is a Cisco IOS Software upgrade to the existing Cisco IOS Software image-not an operating system "swapout". In converted access points operating in lightweight mode, Cisco IOS Software continues to run on the access point, while LWAPP is used to communicate with a wireless LAN controller. Since LWAPP supports automatic access point configuration, there is no need to retain or convert the original autonomous Cisco IOS Software access point configuration.
    http://www.cisco.com/en/US/netsol/ns340/ns394/ns348/ns337/networking_solutions_white_paper0900aecd804f1a23.shtml
    Cisco Aironet Access Point Support for Lightweight Access Point Protocol
    http://www.cisco.com/en/US/products/ps6521/prod_bulletin0900aecd80321a2c.html
    Upgrading Autonomous Cisco Aironet Access Points to Lightweight Mode
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a00804fc3dc.html#wp157147
    Hope this helps!
    Rob

  • Lightweight Mode Upgrade Tool

    I have installed the latest version of the tool, 3.4, and installed it on an XP SP2 box. Everything looks good, but when I start it returns "C:\Program Files\Cisco Systems\Upgrade Tool\images\c1310-rcvk9w8-tar.124-10b.JA3 - LWAPP Recovery Image is not a valid one".
    I have verified that the file exists and is named correctly. I have also downloaded a new copy of the application and image and installed on a different computer and got the same results. Any ideas?

    Hi EMKF,
    I don't think the problem is with the tool it is with this image "c1310-rcvk9w8-tar.124-10b.JA3" I don't know why they have linked this in the Software Downloads to the LWAPP Upgrade image but I'm pretty sure it is wrong.
    As far as I know all recovery images are JX (not JA etc.)
    I would try this image instead;
    12.3(11)JX1.
    Note This release must only be loaded onto access points at the factory or by using the Autonomous to Lightweight Mode upgrade tool. Your access point might become inoperable if you install this software without using the upgrade tool.
    Release Notes for Cisco Aironet 1100, 1130, 1200, 1230, 1240, and 1300 Series Access Points for Cisco IOS Release 12.3(11)JX1
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/b311jx1.html
    c1310-rcvk9w8-tar.123-11JX1.tar
    Here is the link;
    http://tools.cisco.com/support/downloads/go/ImageList.x?relVer=12.3(11)JX1&mdfid=279141937&sftType=Autonomous%20To%20Lightweight%20Mode%20Upgrade%20Image&optPlat=&nodecount=3&edesignator=null&modelName=Cisco%20Aironet%201310%20Access%20Point/Bridge&treeMdfId=278875243&treeName=Wireless&modifmdfid=null&imname=null&hybrid=Y&imst=N&lr=Y
    Check out these notes (no mention of LWAPP Upgrade image)
    Release Notes for Cisco Aironet Access Points and Bridges for Cisco IOS Release 12.4(10b)JA3
    http://www.cisco.com/en/US/docs/wireless/access_point/ios/release/notes/12_4_10b_JA3rn.html
    Hope this helps!
    Rob

Maybe you are looking for