Upgrade Catalyst 4500 Supervisor Engine 8-E(IOS XE Software)
Folks,
We are looking to upgrade the Catalyst 4500 Supervisor Engine 8-E(IOS XE Software). As of now we are running on 3.3.1XO and as per the Cisco notes version 3.3.2XO which is suggested version.
I would like to find some comparison documents on both these version and establish if there is a need to do the upgrade. What are the fixes that have been done in this version.
Thanks,!!
Hi Nikhil,
Please find release notes of version 3.3.2XO below which can provide you the details to upgrade.
Mainly you need to refer the features it supports and resolved cavets (which means the bugs resolved fro the earlier version on to this.).
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_29983-01.html
HTH
Regards
Inayath
*Plz rate if this info is helpfull.
Similar Messages
-
Catalyst 4006 chassis with CATALYST 4500 SUPERVISOR V
Hi Experts,
Can I use CATALYST 4500 SUPERVISOR V(WS-X4516) in an old 6-slot catalyst 4006 chassis( WS-C4006). I want to run the latest IOS available and I have the following line cards:
WS-X4232-RJ-XX
WS-X4418-GB
WS-X4148-RJ
thanks and regards
alexHi Alex
Yes you can run the Sup V in the 4006 chassis. See this link
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/hardware/module/guide/01overvw.html#wp1015031
The Sup V also supports the WS-X4418-GB and WS-X4148-RJ modules - see attached link
http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet09186a00801fcaba_ps2797_Products_Data_Sheet.html
HTH
Jon -
Configuring VSS on Catalyst 4500 Supervisor 8-E
I am trying to configure VSS between two Catalyst 4510R+E chassis that are equipped with dual Supervisor 8e blades, all running enterprise services licenses. I have configured SSO and NSF on both chassis, but when I get to the step to configure the virtual switch domain, I'm unable to proceed any further. I'm only able to get the following output:
Switch(config)#switch virtual ?
% Unrecognized command
According to the VSS setup documentation, I should be able to input switch virtual domain <#> at this point to configure the virtual domain for VSS.
I'm guessing that the problem is the IOS version that the supervisor engines are running, which is 3.3.0XO. I know on the Supervisor 7-E blades, IOS version 3.4.0SG or higher is required to run VSS.
Can anyone confirm whether or not 3.3.0XO supports VSS? Cisco's data sheet states that the 8-E supports VSS, but the release notes are rather vague:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/release/note/OL_29983-01.html
If 3.3.0XO does not support VSS, can anyone confirm whether or not 3.4.0SG is supported on the Supervisor 8-E?IOS-XE 3.6.0 does support VSS on Sup8 - Please make sure to upgrade the rom before attempting to upgrade the sup.
ROM version = 15.1(1r)SG4
HTH
Luke -
Catalyst 4006 Supervisor Engine 3 - routing features
How to ensure the Supervisor Engine 3 module has been integrated into Catalyst 4006? Any command I can use to make sure this? I am going to use it to do all routing for a enterprise network.....
I do not understand your question. Sup3 for CAT 4006 runs IOS and can route EIGRP/OSPF/IS-IS with enhanced image and RIP/static routes with Basic image.
-
Catalyst 4500, supervisor II+, EIGRP
Hi,
We're bought a catalyst 4500 sup II+ with image cat4000-i9s-mz.122-25.EWA4.bin
In feature navigator isn't anything about EIGRP in this image, but in CLI I may configure EIGRP.
How is that possible?
thxHi,
You can only configure the EIGRP stub on the Sup 2+. EIGRP fully is not supported on sup2+.
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat4000/12_2_31s/conf/l3_int.htm#wp1042868
http://www.cisco.com/en/US/products/hw/switches/ps4324/products_data_sheet09186a0080197424.html
HTH, Please rate if it does.
-amit singh -
COMPATIBILTY OF MY WIRELESS OFFICE JET 4500 G510N PRINTER WITH THE IOS AIRPRINT SOFTWARE
IS MY WIRELES OFFICE JET 4500 G510N PRINTER COMPATIBLE WITH THE IOS AIRPRINT SOFTWARE IN THE IPAD2
This question was solved.
View Solution.No. You can use it with the ePrint mobile app for iOS devices. You can find out more by following the links below. Hope this helps.
Supported Printers for the HP ePrint Mobile App or HP ePrint Home & Biz:
http://goo.gl/RsNpf
HP ePrint Mobile Apps FAQs:
http://goo.gl/33WFq
-------------How do I give Kudos? | How do I mark a post as Solved? -------------------------------------------------------- -
Cisco Catalyst 6500 Supervisor Engine 2T Baseboard
Morning Guys
i have just bought a Cisco 6506-E Chassis, it came out with only the SUP2T Engine on slot 5, i have already stacked 3 switches (3750-X) as my core, i want to replace them with the chassis the problem now is my company doesn't have money to buy the 48 port switch and the fibre switch for the chassis, help me link the SUP2T Engine with the stack and improve my network. i also have the 12 port netgear fibre switch. help with the configuration.You obviously need to configure the ports etc. but the switch should recognise the module as long as you have an IOS that supports it.
There is nothing extra to do, you just slot the module in.
If you are connecting all your distribution switches to the 6500 then if you don't need a vlan/IP subnet in multiple buildings then you should use L3 connections to the 6500.
Note also that you may want to consider at some time in the future a second supervisor or another chassis as this 6500 with one supervisor is a single point of failure ie. if it goes then there is no communication between buildings.
Jon -
Supervisor Engine catalyst6500 Modular IOS ??
Hi all,
I want to know the difference between the software that is Modular and the one that is not.
What are the pros and cons ??
which one is better??
CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH or CAT6000-SUP32 IOS ADVANCED IP SERVICES SSH (MODULAR)
thanks!Don't bother with the Modular IOS. It won't be long before Cisco will discontinue this.
-
I just want my pictures, texts, and contacts. It looks like my computer hasn't recorded a backup for my phone since I got it last year.
Thanks for reply,
It's truely a disestar for me to kill my phone myself by so called bloody upgradation.
Iwish I have not upgraded.
I baught it from here in Bangladesh and now I’m ina mess to get at least a minimum support.
Thanks for your valued suggessions but it didn’tmade any difference to my situation.
So now I have an ipod in the price of an iPhone4. Crap.
Is there any chance of fixing this bug by apple?As the same problem has already been faced by a lot of iPhone Users. -
SFP-10G-ZR support on Catalyst 4500 SUP6E
Hello,
is the SFP-10G-ZR supported on the SUP6-E with the OneX converter?
BR
O.GEnd-of-Sale and End-of-Life Announcement for the Cisco Catalyst 4500 Supervisor Engine 6-E
The chances of your SE submitting the PER is now ZERO. You'll be forced to upgrade to Sup7E. -
Does Supervisor Engine 6L-E compatible with Cisco Ws-C4506 Non-E switch?
Does Supervisor Engine 6L-E compatible with Cisco Ws-C4506 Non-E switch?
Yes, it is compatible with non-e chassis.
see below:
The Cisco Catalyst 4500 Supervisor Engine 6L-E is also compatible with classic Cisco Catalyst 4500 line cards, chassis (3-, 6-, and 7-slot), and power supplies, providing full investment protection.
link to data sheet:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/data_sheet_c78-530856.html
HTH -
QoS trust dscp or cos on catalyst 4500
We have a 4510R with Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software cat4500e-UNIVERSALK9-M), Version 03.05.02.E RELEASE SOFTWARE (fc1).
I want use qos trust dscp or qos trust cos on the interface conected to other cisco switch or wlan controller.
The current IOS version, do not support qos trust dscp:
SW(config)#interface gi10/16
SW(config-if)#qos tr
SW(config-if)#qos trust ?
device trusted device class
extend Extend trust through a connected device
SW(config-if)#qos trust device ?
cisco-phone Cisco IP Phone
cts Cisco-telepresence
ip-camera Cisco video surveillance camera
media-player Cisco Digital Media Player
SW(config-if)#qos trust device
What is the software that I need for this?. I tried with command lookup tool but the cat4500 do not appears.That is even new for me.
I did a search and found that, now a days you no longer have to provide the Trust DSCP command, it is by default trusted.
Went through this White Paper and excerpts are below:
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
The answer to your question comes from the following excerpt :-
"Previously supervisor engines relied on “port trust” to classify traffic; however, this does not fall into the MQC CLI construct. MQC provides a more flexible capability, i.e. all traffic is trusted by default, an administrator can change this trust state using a policy map. Another difference is the “internal DSCP” value used within the switch to place packets in the proper queue.
Cisco Catalyst 4500E Supervisor Engines do not use “internal DSCP”; rather, it relies on explicit matching of QoS values using class maps so that packets can be placed in the correct queue.
Also, note that there is no specific priority queue: it is not queue 3 or queue 1. The priority queue is simply configured within a class; therefore, it is not tied to a specific queue. One final difference is that of classification. Cisco Catalyst 4500E Supervisor Engines provide sequential classification rather than parallel. This allows the network administrator to classify traffic at egress based on the ingress markings. These markings can be done unconditionally, using a policer or using a table map. Based on these changes, QoS CLI will now be more contiguous on the Supervisor Engines as it will now have standard Cisco MQC CLI, making configuration management much simpler"
HTH,
Please rate all helpful posts.
Regards -
Monitoring dual core (Supervisor Engine 7-E) through EEM Script.
Hi,
I have a Cisco Catalyst 4500E Supervisor Engine 7-E and configured an EEM Script to monitor the dual core CPU Utilization through PRTG Network Monitor.
event manager applet dualcore authorization bypass
event timer cron cron-entry "* * * * 0-6"
action 100 cli command "en"
action 120 cli command "show process cpu | include five"
action 220 regexp "Core 0: CPU utilization for five seconds: ([^%]+)%; one minute: ([^%]+)%; five minutes: ([^%]+)%.*" $_cli_result result c0cpu5sec c0cpu1min c0cpu5min
action 240 if $_regexp_result eq 1
action 260 end
action 320 regexp "Core 1: CPU utilization for five seconds: ([^%]+)%; one minute: ([^%]+)%; five minutes: ([^%]+)%.*" $_cli_result result c1cpu5sec c1cpu1min c1cpu5min
action 340 if $_regexp_result eq 1
action 360 end
action 440 cli command "config t"
action 441 cli command "snmp mib expression owner cisco name c0cpu5sec"
action 442 cli command "expression $c0cpu5sec"
action 443 cli command "snmp mib expression owner cisco name c0cpu1min"
action 444 cli command "expression $c0cpu1min"
action 445 cli command "snmp mib expression owner cisco name c0cpu5min"
action 446 cli command "expression $c0cpu5min"
action 550 cli command "config t"
action 551 cli command "snmp mib expression owner cisco name c1cpu5sec"
action 552 cli command "expression $c1cpu5sec"
action 553 cli command "snmp mib expression owner cisco name c1cpu1min"
action 554 cli command "expression $c1cpu1min"
action 555 cli command "snmp mib expression owner cisco name c1cpu5min"
action 556 cli command "expression $c1cpu5min"
action 600 cli command "end"
end
It works fine but on the logging buffer there are a lot of %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:moncores) messages -one per minute- here an example:
Oct 29 17:54:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:55:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:56:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
Oct 29 17:57:01: %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:dualcore)
I considered to use the logging suppress duplicates command to prevent the consecutive logging of more than one copy of the same system logging (syslog) message but it is only available to the Cisco IOS XR.
Someone could help me to determine if it is possible to avoid this messages through Embedded Syslog Manager, I tried to do that but
I was not successful.
Regards,
~SergioHi,
I did transitioned CLI actions to the EXPRESSION-MIB SNMP but I could not receive anything information about the dualcore utilization on the PRTG Network Monitor and received a lot of %HA_EM-7-FMFD_SNMP_ERRCODE: fh_fd_snmp_errcode: Error status: 6 NO_ACCESS_ERROR: 1. messages on the WS-C4507.
Considering the initial EEM script, could ypu help me to avoid the %SYS-5-CONFIG_I: Configured from console by on vty0 (EEM:moncores)
messages using Embedded Syslog Manager.
Here some snmpwalk to validate that I could not get the OIDs to monitor both cores.
STEP 1 Only one value is given because there is only one physical cpu.
cpmCPUTotalPhysicalIndex
1.3.6.1.4.1.9.9.109.1.1.1.1.2
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.4.1.9.9.109.1.1.1.1.2
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.2.4000 = INTEGER: 4000
STEP 2
entPhysicalName
1.3.6.1.2.1.47.1.1.1.1.7
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.47.1.1.1.1.7.4000
SNMPv2-SMI::mib-2.47.1.1.1.1.7.4000 = STRING: "Linecard(slot 4)"
#sh mod
Chassis Type : WS-C4507R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type Model Serial No.
---+-----+--------------------------------------+------------------+-----------
1 18 10GE (X2), 1000BaseX (SFP) WS-X4606-X2-E JAE151904JC
2 24 1000BaseX (SFP) WS-X4624-SFP-E JAE152001AE
4 4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP7-E CAT1522L0G1
5 48 10/100/1000BaseT (RJ45)V, Cisco/IEEE WS-X4548-GB-RJ45V JAE12067N8K
M MAC addresses Hw Fw Sw Status
--+--------------------------------+---+------------+----------------+---------
1 e8b7.4880.e5db to e8b7.4880.e5ec 1.2 Ok
2 e8b7.48cc.6167 to e8b7.48cc.617e 1.2 Ok
4 4055.39d7.76c4 to 4055.39d7.76c7 1.0 15.0(1r)SG2 03.01.01.SG Ok
5 001e.f7da.d290 to 001e.f7da.d2bf 4.1 Ok
Mod Redundancy role Operating mode Redundancy status
----+-------------------+-------------------+----------------------------------
4 Active Supervisor SSO Active
STEP 3
cpmCPUTotal1minRev
1.3.6.1.4.1.9.9.109.1.1.1.1.7
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.4.1.9.9.109.1.1.1.1.7
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.7.4000 = Gauge32: 9
C:\usr>
ADDITIONAL INFORMATION
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.90
SNMPv2-SMI::mib-2.90.1.1.1.0 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.1.2.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.3.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.4.0 = Gauge32: 0
SNMPv2-SMI::mib-2.90.1.1.5.0 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = STRING: "9"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = STRING: "11"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = STRING: "8"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = STRING: "13"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = STRING: "13"
SNMPv2-SMI::mib-2.90.1.2.1.1.3.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = STRING: "11"
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.4.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 1
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.5.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = ""
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.6.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.7.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = OID: SNMPv2-SMI::zeroDotZero
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.8.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = Counter32: 0
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.49.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.53.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.48.99.112.117.53.115.101.99 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.49.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.53.109.105.110 = INTEGER: 2
SNMPv2-SMI::mib-2.90.1.2.1.1.9.5.99.105.115.99.111.9.99.49.99.112.117.53.115.101.99 = INTEGER: 2
C:\usr>
C:\usr>snmpwalk -v 2c -c m4nc4rc0 10.20.91.2 1.3.6.1.2.1.47.1.1.1.1.2
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1 = STRING: "Cisco Systems, Inc. WS-C4507R+E 7 sl
ot switch "
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.3 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.6 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.7 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.8 = STRING: "WS-C4507R+E 7 slot switch chassis sl
ot"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.9 = STRING: " WS-C4507R+E 7 slot switch backplane
SNMPv2-SMI::mib-2.47.1.1.1.1.2.10 = STRING: "Container of Fan Tray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.11 = STRING: "FanTray"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.12 = STRING: "Container of Container of Power Sup
ply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.13 = STRING: "Container of Power Supply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.14 = STRING: "Power Supply ( AC 2800W )"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.15 = STRING: "Power Supply Fan Sensor"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.16 = STRING: "Container of Power Supply"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.19 = STRING: "Clock Module"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.20 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.21 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.22 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.23 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.24 = STRING: "Mux Buffers for Redundancy Logic"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1000 = STRING: "10GE (X2), 1000BaseX (SFP) with 6
10GE X2 ports"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1005 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.1006 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2000 = STRING: "1000BaseX (SFP) with 24 SFP Ports
Jumbo Frame Support"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2005 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2006 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2007 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2008 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2009 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2010 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2011 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2012 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2013 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2014 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2015 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2016 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2017 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2018 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2019 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2020 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2021 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2022 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2023 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2024 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2047 = STRING: "1000BaseSX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.2048 = STRING: "1000BaseSX"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4000 = STRING: "Sup 7-E 10GE (SFP+), 1000BaseX (S
FP) with 4 SFP+ Ports"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4001 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4002 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4003 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.4004 = STRING: "Port Container"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5000 = STRING: "10/100/1000BaseT (RJ45)V with 48
10/100/1000 baseT voice power ports (Cisco/IEEE)"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5001 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5002 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5003 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5004 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5005 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5006 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5007 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5008 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5009 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5010 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5011 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5012 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5013 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5014 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5015 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5016 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5017 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5018 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5019 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5020 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5021 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5022 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5023 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5024 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5025 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5026 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5027 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5028 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5029 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5030 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5031 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5032 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5033 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5034 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5035 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5036 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5037 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5038 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5039 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5040 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5041 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5042 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5043 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5044 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5045 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5046 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5047 = STRING: "Gigabit Ethernet Port"
SNMPv2-SMI::mib-2.47.1.1.1.1.2.5048 = STRING: "Gigabit Ethernet Port"
C:\usr> -
IDS/IPS functionality in Catalyst 4500 ?
Hi,
is there an IDS/IPS functionality in Catalyst 4500 (Supervisor 6-e), or do we need to propose external IDS/IPS device?I think cat 4500 sup 6-e does not have IDS/IPS functionality. You have to externally install it.
http://www.cisco.com/en/US/prod/collateral/modules/ps2797/ps9294/product_data_sheet0900aecd806df543_ps4324_Products_Data_Sheet.html -
after upgrading ios Cisco Catalyst 6500 Series Supervisor Engine 2T to the latest release the ASA-SM module is not recognized it is disabled. the FPD
is not recognized any more. reverted back to previous ios with no luckDuplicate post.
Being discussed actively in this thread.
Maybe you are looking for
-
Hi Experts; How do I add a caret listener on this code so that it will just add a number when the user goes to the next line. import java.awt.*; import javax.swing.*; public class LineNumber extends JComponent private final static Color DEFAULT_
-
HT201363 i Want To Buy a Game On The phone but the security Questions i forgot and the Email
I Have a Iphone 5c i Want To Buy a Game On The phone but the security Questions i forgot and the Email To Change Them i forgot can you please help me with the email i sent them To? <Edited by Host>
-
Create xml from xml schema in java
If can i create a xml document framework from xml schema in java, then i can fill the value in java? thanks
-
I have an iPad 1 and cannot get my rental movie to download- I just keep getting download error message?
-
MY IPOD XMAS GIFT HAS MUSIC GENERATED ON A MAC. ITUNES WILL NOT RECOGNIZE IT ON MY PC WITH WINDOWS 8.1 UNLESS IT IS RESTORED WHICH ITUNES STATES WILL WIPE OUT ALL EXISTING +1000 TUNES. WHAT OPTIONS DO I HAVE?