Upgrade eMAc using Kingston 1GB PC3200 400Mhz

Hello guys
Just want to get some clarifications. Is it possible for me to upgrade my eMac G4 1.25Ghz using kingston 1GB PC3200 400Mhz memory. i have two stick in my collection after upgrading my office pc with higher one.
thanks

I should probably clarify the "high-density" issue. High-density RAM is common in peecees and pack more RAM into fewer components. Example: a high-density RAM module may have only eight black chips; low-density would have 16 for a module of the same capacity.
When certain high-density RAM modules are installed in a Mac requiring low-density RAM, it shows up as exactly half its rated capacity.
So that's why it's the RAM density and not its speed )PC3200) that is at play in your situation.

Similar Messages

Kingston 1GB PC3200 CL3 compatible ?

greetings,
i received 1gb kingston memory card as a gift. i'm not sure if it's compatible with my 1ghz 15" (aluminum) powerbook. random searches yielded no results. is there a definite way to know (short of trying to install it)?
thank you!

The only RAM that Kingston makes that is fully compatible with the PowerBooks are the KTA-PBG4333 series SODIMMs. In your case, if it does not have the model number KTA-PBG4333/1G on it then the answer is no, it is not fully compatible.
While you may find that it mostly works the issues appear when the processor changes speed. You can get often around this by having the same speed setting (Highest or Reduced) for both Power and Battery modes in the Energy Saver System Preference. Using the Automatic setting will invariably cause stability issues.

1Gb DDR 400MHZ RAM Banks falled on K7N2 Delta2 ultra400

Hi.
Have Problems with my MSI K7N2 Delta2.
Stock up my RAM with 1Gb Banks. But nothing more, then an Beep at boot..
But the Board will max 3GB on 3 Slots..
Its Samsung 1gb PC3200 400Mhz High density, non ecc, 128x64
what can i do.? flash bios.? its a original bios installed..
thanks to all

Hi.
Thanks for your answer.
My english is bad. I from Germany, but i live in spain.
Maybe en german or spanish better..
My RAM actual: 1x 512MB DDR 400Mhz PC3200U
2x 512MB DDR 333Mhz PC2700
And now will install the max of the Board
Samsung DDR 1GB 400Mhz, PC3200, CL3
DRAM, DDR SDRAM, DIMM 184-PIN, 400 MHz ( PC3200 ), CL3, Non-ECC, 8K-Refresh , unpuffert, 128 x 64, 2.6 V
I'm not sure, that is high or low density..
but when is installed (one or three) ever the same, blue screen and large beep from the speaker. also i change the banks back to the 512MB and boot normaly with 1,5GB RAM.
but really better are 3GB..
My Machine:
(In this option boot 2x512MB +1x1GB)
Computadora:
Tipo de computadora Monoprocesador ACPI de PC
Sistema operativo Microsoft Windows XP Professional
Service Pack del sistema operativo Service Pack 3
Internet Explorer 8.0.6001.18702 (IE 8.0)
DirectX 4.09.00.0904 (DirectX 9.0c)
Nombre de la computadora NOMBRE_EQUIPO (Power Tower)
Nombre de usuario Administrador
Dominio de inicio de sesión NOMBRE_EQUIPO
Fecha / Hora 2011-12-06 / 15:11
Motherboard:
Tipo de CPU AMD Athlon XP, 1666 MHz (12.5 x 133) 2000+
Nombre del motherboard MSI K7N2 Delta-IL (MS-6729) (5 PCI, 1 AGP, 1 ACR, 3 DDR DIMM, Audio, LAN)
Chipset del motherboard nVIDIA nForce2 Ultra 400
Memoria del sistema 1024 MB (PC2700 DDR SDRAM)
DIMM1: Kingston 1 GB PC2700 DDR SDRAM (3.0-3-3-7 @ 166 MHz) (2.5-3-3-7 @ 166 MHz) (2.0-3-3-6 @ 133 MHz)
DIMM2: MDT Tech. MDT512M PC333 CL2. 512 MB PC2700 DDR SDRAM (2.5-3-3-7 @ 166 MHz) (2.0-3-3-6 @ 133 MHz)
DIMM3: MDT Tech. MDT512M PC333 CL2. 512 MB PC2700 DDR SDRAM (2.5-3-3-7 @ 166 MHz) (2.0-3-3-6 @ 133 MHz)
Tipo de BIOS Award (07/17/03)
Puerto de comunicación Puerto de comunicaciones (COM1)
Puerto de comunicación Puerto de impresora ECP (LPT1)
Monitor:
Placa de video ATI Radeon HD 4600 Series (1024 MB)
Placa de video ATI Radeon HD 4600 Series (1024 MB)
Aceleradora 3D ATI Radeon HD 4670 AGP (RV730)
Monitor Nexgen NL30 [30" LCD] (13481)
Multimedia:
Placa de sonido ATI Radeon HDMI @ ATI RV710/730/740 - High Definition Audio Controller
Placa de sonido nVIDIA MCP2 - Audio Processing Unit (Dolby Digital)
Placa de sonido Realtek ALC650 @ nVIDIA MCP2 - Audio Codec Interface
Almacenamiento:
Controlador IDE NVIDIA NForce MCP2 IDE Controller
Disquetera Unidad de disquete
Disco rígido WDC WD3200JB-00KFA0 (298 GB, IDE)
Estado SMART de los discos rígidos OK
Propiedades del BIOS:
Fabricante Phoenix Technologies, LTD
Versión 6.00 PG
Fecha de salida 07/17/2003
Tamaño 256 KB
Dispositivos de arranque Floppy Disk, Hard Disk, CD-ROM, ATAPI ZIP, LS-120
Funciones disponibles Flash BIOS, Shadow BIOS, Selectable Boot, EDD
Estándares soportados DMI, APM, ACPI, PnP
Posibilidades de expansión ISA, PCI, AGP, USB
Propiedades del motherboard:
Fabricante MICRO-STAR INTERNATIONAL CO., LTD
Producto MS-6729
Propiedades del controlador de memoria:
Método de detección de errores 8-bit Parity
Corrección de errores Ninguno/a
Memoria entrelazada soportada 1-Way
Memoria entrelazada actual 1-Way
Velocidad de memoria soportada 70ns, 60ns
Tipos de memoria soportadas SPM, EDO
Voltajes de memoria soportados 5V
Tamaño máximo de los módulos de memoria 32 MB
Slots de memoria 3
[ Procesadores / AMD Athlon(tm) XP ]
Propiedades del procesador:
Fabricante AMD
Versión AMD Athlon(tm) XP
Reloj externo 133 MHz
Velocidad de reloj máxima 2200 MHz
Velocidad de reloj actual 1666 MHz
Tipo Central Processor
Voltaje 1.5 V
Estado Activado/a
Actualización ZIF
Identificación del socket Socket A
and 480W Powerunit
You can see, that everest know the 1Gb RAM Bank..
What can i do.?
Thanks to all..
Alexx

Msi K8n Neo2 Platinum & Kingston Hyperx 1gb Pc3200

I have recentrly bought a MSI K8N NEO2 PLATINUM together with KINGSTON HYPERX PC3200 1GB KIT (which should run 2-2-2-5-1T)
But for the moment I only get them stable at 2.5-3-3-8-1T)
If I change from 2.5 -> 2 NO BOOT , i have to use the reset jumper...
The voltage I use is 2,75V
What can you guys suggest ?
Best Regards,
Yves

yes, when I changed the 2T to 1T I noticed a rather big diference ...
but still ... I bought those for the 2-2-2-5-1T setting so I will rma them if I can't get them to run at that speed...
I have send an email to kingston ... also waiting for their reply ...
also this evening I will try it with a more powerful PSU !
best regards
Yves

Upgrading a used emac to mac osx

I shall purchase a used emac, g4, 700mhz,256 ram,40gb hd, mac os 9.2.2
I own mac os x 10.2 on two cd's. may i upgrade the used emac's os 9.2.2 with the two mac osx 10.2 cd's that I own?
thanks in advance
mike long
addison texas usa

If the OS is not installed on another CPU, then you can install it on any single Mac with which it is compatible.
The software license is indeed on paper, and you can visit the Apple website to find online copies of their license agreements.
In case you aren't aware the Apple Discussions are provided by Apple. Any discussion of illegal uses of software or hardware would violate the Terms of Use for the Discussions. Furthermore, were we to advise you to ignore Apple's license agreements then we would be guilty of abetting illegal acts. I presume you can understand why no one here will answer your query about violating the license. Any continued discussion of same will likely result in your topic being removed.

Msi Neo2 Kingston HyperX PC3200 BH5 Any Good ?

Hi Guys
Anyone using 2x256mb Kingston HyperX Pc3200 Bh5 on the neo2?
curious at what fsb/timings u can run.
and if 3.1-> V would help.
thinking of buying a pair but would be great seeing some results first.
thx in advance.

nice thread crap...
i ordered the exact ram you are talking about, and it is a STEAL at its current price at outpost.com. ill be receiving my sticks tomorrow, so ill have to wait and see what they can do over the weekend.
however, its been shown that BH-5 memory performs at its best at 3V+, and this board can only do 2.85v. so, it remains to be see what can be achieved. i hope a BIOS update will bump up the voltage.
go ahead and get it. its a great deal at that price.

Can you install Panther on an eMac using retail disks?

I've had problems in the past installing Panther onto an eMac using retail disks.
is there a problem doing this??
past issue - once installed, and booting for the first time, the screen on the eMac would only show the center 50%, the cursor would not go outside of it but there were buttons and icons outside of it. i had to install from the eMac disks and then upgrade to server. (i was doing a OS X Server install onto an eMac then)
current issue - i can't boot from the Panther disk 1!!! checking to make sure it is not the disk..... my client was in the middle of installing Panther, and in the middle of disk 1 it froze and i think gave a KP based on his report of what happened.
thanks
bob

When you get the blinking mac face/question mark when booting, this means that your machine can't find the startup disk it's looking for - whether cd or hard drive. After a moment, it then searches until it finds any startup disk. You can lose your Classic - OS9, while doing operating systems loads if you don't restore it from your original system disks that came with your machine. There may be problems trying to go back to 10.2 from 10.3. It's not a problem I've had, but someone was telling me that the major upgrades (Jaguar to Panther) may have firmware updates that aren't compatible if you try to reload the older OS. It's best to install Panther, then reinstall your applications from the original disks that came with your machine.

Can I use kingston ddr 333 along with Kingmax ddr 333

Ok I wanted to add some more memory to my system I have 2 x sticks of 256 ddr 333 Kingmax right now. I would like to add some more ram but I cant seem to find Kingmax memory online I can find a stick of 256 but not a 512 I see alot of Kingston 512 stick and 1 gig can I use Kingston along with Kingmax ram? I dont want to spend too much on this upgrade since I will be upgrading my Mobo and Cpu in a few months and this memory would be too slow for a new system.

Quote
My comments are a probability
Your comments are uninformed.
Quote
A question for you, what do you mean by specification?
Product specifications, module specifications, component specifications.
Quote
No its not, you dont know the PCB revision, make, model.
I would not mix double sided with a single sided module.
lol! Its not 1994 anymore. Where have you been? Mixing DRAM speeds, capacities, and timings has not been a significant issue for years now. Memory controllers are designed[/i] to accomodate separate timing and speeds for each memory bank.
Remember VIA Apollo Pro133/133A (VT82C693/694X) from way back in like 1971?
Quote
VT82C694X DRAM controller supports standard Synchronous DRAM (SDRAM) and Virtual Channel SDRAM (VC SDRAM), in a flexible mix / match manner. The Synchronous DRAM interface allows zero wait state bursting between the DRAM and the data buffers at 66/100/133 MHz. Six banks of DRAM can be composed of an arbitrary mixture of 1M / 2M / 4M / 8M / 16M / 32MxN DRAMs up to 1.5GB.
Remember KT133/KT133A (VT8363)?
Quote
VT8363A Advanced High-Performance DRAM Controller:
-Different DRAM types may be used in mixed combinations
-Different DRAM timing for each bank
-Mixed 1M / 2M / 4M / 8M / 16M / 32MxN DRAMs
-Flexible row and column addresses
-Independent SDRAM control for each bank
nForce and nForce2:
Quote
The TwinBank architecture is designed to provide a high degree of flexibility, scalability and upgradeability. Its technical benefits include:
• Both 64-bit and 128-bit operations. In 64-bit mode, the DIMM can be located on either MC1 or
MC2. In 128-bit mode, both MC1 (DIMM0) and MC2 (DIMM1/DIMM2) are utilized.
• Both controllers are functionally identical with all control and timing parameters independently programmable. This allows asymmetric DIMMs with different memory organization, size, and speed to be used on MC1 and MC2 and still provide the full performance benefits of the 128-bit memory system.
• Support for odd total memory size; eg. 64MB + 128MB = 192MB, while still taking advantage of
the 128-bit TwinBank architecture.
Quote
NFORCE2 DualDDR Memory Architecture
Both of the memory controllers on DualDDR are functionally identical with all control and timing parameters independently programmable. This flexibility allows the users to populate up to three asymmetric DIMMs in any organization, size and speed. DualDDR simply adjust to the lowest common density that will facilitate 128-bit bandwidth, allowing a wide variety of different DIMM combinations to operate reliably regardless of the individual density and latency characteristics.
SIS 655FX/655TX:
Quote
Flexible Dual Channel
This feature allows users to “mix and match” memory sizes and odd number of sticks to operate in Dual Channel mode.
Do you think memory controllers have become less[/i] sophisticated since the days of VIA VP3 Socket 7 (which, BTW, also supported arbitrary DRAM mixing)?
The ability to run different speeds, sizes, and densities of DRAM isn't just an accidental byproduct of advancing memory controller technology. It is intentionally being built-in[/i] to the design to accomplish this.

Upgraded eMac, now fan won't work

Hello,
I just upgraded my son's eMac - put in 1GB RAM, Pioneer DVD-R drive and 320 GB hard drive.
All the upgrades work just fine (and he is very happy), but now the fan won't work. I've checked and double-checked the connections - there were two connections that I've unplugged and plugged in three times. The fan can spin if I flick it, so it is not impeded in any way.
Any ideas?
eMac Mac OS X (10.4.9)

Yes, the fan was operating fine because it was so loud you couldn't miss it.
I appreciate Roam's comments, but my electrical engineering background is spotty. I understand that it is either the fan or the connection to the fan, but I have not the tools nor the knowledge to connect a battery to see if the connection is good.
What I can't figure out is what went wrong. There are only two connections coming from the fan unit, and one is actually the power supply that goes to the electrical plug (which is part of the fan unit). That one is obviously working fine because the computer powers up. The other one is this simple looking small snap-in connector that seems like a total no-brainer to attach. It's not something that could even easily get bent or anything.
I'm obviously missing something important, or the fan picked a really weird time to stop working.
For now he's shutting the computer down when it feels hot. I'm sure that's not a good solution.

If I have a 2009 iMac, can I upgrade to use it with Apple TV. It doesn't have Airplay capability. If possible, what should I buy?

If I have a 2009 iMac, can I upgrade to use it with Apple TV. It doesn't have Airplay capability. If possible, what should I buy?

You need a newer 2011 or later iMac to use Airplay.
Sorry.
For older Mac, look at an app called AirParrot
http://www.airsquirrels.com/airparrot/

Where can I upgrade to use DV capture?

Where can I upgrade to use DV capture?

invernessms
If your program is Premiere Elements 13 which no longer has the DV HDV Capture firewire, you can get a suggested Adobe workaround for the 13 situation.
Please refer to the following Adobe document.
http://helpx.adobe.com/premiere-elements/kb/removed-features-formats-elements.html
ATR

My iPad shows using 4.1GB of storage for mail, even though I have delete all content in the folders. How do I get this storage back?

My iPad shows using 4.1GB of storage for mail, even though I have deleted all content in the folders. How do I get this storage back?

My iPad shows using 4.1GB of storage for mail, even though I have deleted all content in the folders. How do I get this storage back?

CC&B 2.1.0 upgrade of use of Microfucos visual cobol from net express

Would there be any issue of upgrading the use of Microfocus Visual Cobol from Net Express?

starfry wrote:I don't know if it's related to your problem but GPG2.1 doesn't allow pass phrases to be specified in a file or on the command-line. See the page on unattended operation, look at "%ask-passphrase" and "%no-protection" https://www.gnupg.org/documentation/man … ation.html
Thanks for the link - that's only for gen-key, however. But I do confirm the "--passphrase-fd 0" is supposed to still be working as described in the current docs:
https://www.gnupg.org/documentation/man … ic-Options
--passphrase-fd n
Read the passphrase from file descriptor n. Only the first line will be read from file descriptor n. If you use 0 for n, the passphrase will be read from STDIN. This can only be used if only one passphrase is supplied.
So in theory the functionality hasn't changed. :-/

What's hardware should upgrade for Using Premiere CS4 to editing (AVCHD)m2ts file?

What's hardware or software should upgrade for Using Premiere CS4 to editing (AVCHD)m2ts file?
1st question: when i try to do editing by using Premiere CS4 AVCHD sequence timeline, the edting monitor seems not smooth (like wearing goggles) & delay, and when i use AME to encode m2ts file (which not yet edit) to AVI file (about 1 hour), it take 2h 13min to finish, is it normal?
2nd question: i use mpeg2 HD 1440 file to do eding, the edting monitor also not very smooth but better than using m2ts file, after editing done, i try to encode these mpeg2 HD 1440 file (which edited about long 1 hr) to a New file mpeg2 1440 X 1080i HQ or even mpeg2 Pal DV HQ file, the encoding was not runthe encoding after wait for half an hour. How many hours it take usually????
3rd question: i use m2ts file video file to export as a Bitmap, 1 frame 1 picture bitmap, it take long time too, about 1 or 2min to finish encoding, if i export more than 1 picture, it take even more time, i have experienced it, 3 or 4 pictures need about 10 or 15 min to finish encoding. i used to using mpeg2 HD 1440 file (which edited file) to export frame as picture, it not run the encoding at all. WHY ????
i'm new in Premiere CS4,so i got many question about Premiere CS4, usually i use Premiere Pro 1.5 version
my computer is: Intel (R) Core (TM) 2 Duo CPU
                         E7400 @ 2.80 GHz
                         2.80 GHz, 2.00 GB RAM
                         Graphic Card: ATI Radeon X1650 series
                        2 Hard Disks in my computer (C Drive is 300 GB (not sata) , D Drive is 500 GB sata)
4th Question: Premiere CS5 & Premiere CS4 which one is better ???
5th Question: What's different ATI Radeon and NVIDIA Card, which is better, which u suggest to. What is different Graphic Card and Video Card ?? Should i install HD Video Card ????

I don't think a core-2 will work very well with AVCHD... you need at least an Intel i7 920... or whatever is current
My CS5/AVCHD 1st Impressions http://forums.adobe.com/thread/652694?tstart=0 includes a link to the computer I built... since the GTX 285 is no longer sold, I would now go with a GTX 460 or whatever is the current "best bang for the buck" - AND I would buy 4Gig-by-3Sticks memory to be able to expand from 12Gig to 24Gig if needed
For my home hobbyist, family movies (which means that I am not trying to recreate Star Wars with video effects or many layers) AVCHD editing is "as smooth as spreading warm butter on hot toast" (also the MP4 video from wife's Flip camera)
My 3 hard drives are configured as...
1 - 320G WD Win7 and all programs
2 - 320G WD Win7 swap file and PPro projects
3 - 1T WD all video files... read and write

What is the Upgrade program used to upgrade NW04 to NW04s

Hi,
What is the Upgrade program used to upgrade NW04 to NW04s?
Thanks Sri

<b>SAPup</b> - Program to upgrade Web AS ABAP and related components BW,XI
<b>SAPJup</b>- Program to upgrade WebAS Java and related components EP.
Vijay Kothapalli

Upgrade eMAc using Kingston 1GB PC3200 400Mhz

Similar Messages

Maybe you are looking for