Upgrade file pattern error

Model BEFW11S4
Version 3
Firmware 1.2.
I have connected my Win XP laptop with cable directly to the router, and I am trying to update firmware to version 1.45.10 which should be the correct update for my model, but the upgrade is interrupted with "Upgrade file pattern error".
I have tried hard-resetting the router before upgrading, but with the same result.
What to do?

How are you upgrading the routers firmware? Are you using the router web-based user-interface? If you are then try using this alternate way...
Go to www.linksys.com/downloads .. search for BEFW11S4 v3 ... then download the Set-up Wizard. Use this to upgrade your router instead. When you run this program, it will ask you for a server, password and then a file. Server is the router IP, password is the router password (default is admin) and file would be the firwmware you downloaded... once you input the necessary info... hit upgrade and you should be good to go.

Similar Messages

WRK54G firmware upgrade fails: file pattern error.

When I attempt to upgrade the firmware in my WRK54G router, the upgrade fails with this error message:
Upgrade action is not finish!!
Upgrade file pattern error.
The linksys download page says the file size is 1.10 MB.
The size of the file I downloaded (WRK54Gv2_1_00_1) is also 1.10 MB (1,160,036 bytes). So it appears the file was downloaded successfully.
I had no problem upgrading the firmware to version 1.1.
Please advise.
Thank you

What is the hardware version of your router? Is it version 1, version 1.1 or version 2? Where did you download the firmware of your router? Is it from the US website.
On the US website you have 3 wrk54g, one is version 1, version 1.1 and v2.
"When love and skill work together, expect a masterpiece."

ISE Upgrade File Copy Error

According to the Upgrade Guidelines for 1.2:
Copy the upgrade bundle to the local disk using the copy command from the Cisco ISE CLI: copyftp-filepath ise-upgradebundle-1.1.x-to-1.2.0.899.i386.tar.gz disk:/ Again, after you copy the upgrade bundle to the local disk, check to ensure that the size of the upgrade bundle in your local disk is the same as it is in the repository. Use the dir command to verify the size of the upgrade bundle in the local disk.
When I attempt to run this command, I keep getting the error:
"% long command detected at '^' marker"
using the following command:
" copy repository FTPDPZ ise-patchbundle-1.2.0.899-1-82500.x86_64.tar.gz"
I have also tried to replace the repository + name with an IP address, with just the repository name, and with 100 other things.
I tried to look up what a "long command" is, but I come up with nothing.
What is the proper verbage to utilize this command?

David,
It figures, doesn't it? No worries. The repository system is a confusing one, but it is what we have. I have found detailed instructions on using it, but they are for the Cisco Prime LMS product. The process is the same (I used these unstructions when doing my ISE 1.2 Upgrade), just substitute file names as necessary.
Step 1 Log into the shell and navigate to the location where the upgrade file, lms4_2_3_lnx_k9.zip is stored.
myhost/admin# shell
starting shell...
[myhost/ root-ade ~]
Note The login name that appears in the command prompt depends on the login name entered by the user while installing LMS on VM Console.
Step 2 Unzip the lms4_2_3_lnx_k9.zip file to extract Cisco_Prime_LAN_Management_Solution_4_2_3.tar.gz.
[myhost/ root-ade myloc] unzip lms4_2_2_lnx_k9.zip
Step 3 Copy the Cisco_Prime_LAN_Management_Solution_4_2_3.tar.gz to local disk partition of LMS 4.2.2 installed server (/localdisk).
Step 4 Log in with your credentials to the VM Console through Vsphere client.
Step 5 Create either a local or remote repository. A repository contains URL and credential details
myhost/admin# configure terminal
myhost/admin(config)# repository <>
myhost/admin(config-Repository)# url ?
Enter repository URL, including server and path info (Max Size - 80)
cdrom: Local CD-ROM drive (read only)
disk: Local storage
ftp: URL using a FTP server
http: URL using a HTTP server (read only)
https: URL using a HTTPS server (read only)
nfs: URL using a NFS server
sftp: URL using a SFTP server
tftp: URL using a TFTP server
Step 6 Combine the URL to the repository that uses a local or remote storage.
a. The following IOS CLI shows how to combine the URL to a repository that uses a local storage:
myhost/admin(config-Repository)# url disk:
myhost/admin(config-Repository)# exit
myhost/admin(config)# exit
myhost/admin# write mem
Generating configuration...
myhost/admin#
b. The following IOS CLI shows how to combine the URL to a repository that uses an anonymous FTP server:
myhost/admin(config-Repository)# url ftp://<>
myhost/admin(config-Repository)# user <> password plain <>
myhost/admin(config-Repository)# exit
myhost/admin(config)# exit
myhost/admin# write mem
Generating configuration...
myhost/admin#
You can use the above mentioned steps for other protocols.
Step 7 Run the below command in the VM console in VSphere client.
myhost/admin# application upgrade Cisco_Prime_LAN_Management_Solution_4_2_3.tar.gz <>
Save the ADE-OS running configuration? (yes/no) [yes]?
Step 8 Press Enter to continue with LMS 4.2.3 upgrade.
An Application upgrade successful message appears.
Here is the doc that contains these instructions:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2.3/release/notes/lms4_2_3_release_notes.html#wp1183869

Download Helper, even with paid converter upgrade, gives "Invalid Capture File" errors and will not record audio, with "File Creation Error - Unable to rename/copy audio file" Error.

Download Helper Screen Capture worked to capture video if the default "no audio" option is active. But, no audio. The "speakers" or "microphone" audio options are confusing....the audio to be captured is from the video, so what do you choose? With either "speakers" or "microphone" selected, the captured file has poor audio and no video. Re-capture efforts (speakers) get "Invalid capture file error" and "File Creation error- Unable to rename/copy audio file"
The paid upgrade of "Converter" doesn't work.
Instructive documentation - not very good.
Suggestions - Need time delay between initiation of "Record" and starting the video to be recorded.
Could use timer tracking of the record process.
Are there operating system limitations? (Have Windows XP Pro)

That is an issue for the developer of that Download Helper.

Itunes was working fine. Tries to install latest upgrade and get error message about an invalid character in the path "Program Files (x86)". PC, Win7, nothing else appears to be having same issue.

Itunes was working fine. Tried to install latest upgrade and get error message about an invalid character in the path "Program Files (x86)". PC, Win7, nothing else appears to be having same issue. Program still works, simply cannor upgrade.

Thanks b noir,
I tried this solution without success. After FixIt ran and didn't find a problem, either in looking for issues with "software upgrade" or "iTunes" it kindly offered to help me uninstall iTunes. I had thought of this as a possibilty but it seems to me that if you do that you lose a lot of "non-native-to-Apple" information you might have entered. I did this once and recovery was painfull. Is there a way to uninstall iTunes without losing all of that sort of thing? Any help would be appreciated.

Startup upgrade ORA-00205: error in identifying control file

Hi,
I am doing a manual upgrade from 10.2.04 to 11.2.03.
I have installed 11.2.0.3.
Ran utlu112i.sql
Copied TNSNAMES and LISTENER.ora,init.ora from 10g home to 11g home respective directories.
Commented all dump_dest paramteres in 11g init.ora and added diagnostic_dest parameter
exported all the varaiables as follows.
export ORACLE_HOME=/oracle/ora11203
export PATH=$ORACLE_HOME/bin:$PATH
export ORACLE_SID=OMIGTEST
export TNS_ADMIN=$ORACLE_HOME/network/admin
export ORACLE_BASE=/oracle/ora11203/app/ora11203
Now when i try to start DB from the unix session where all of above variables are set,i am getting following issue.
SQL> startup upgrade
ORACLE instance started.
Total System Global Area 1636892672 bytes
Fixed Size                  2183056 bytes
Variable Size            1090519152 bytes
Database Buffers          536870912 bytes
Redo Buffers                7319552 bytes
ORA-00205: error in identifying control file, check alert log for more info
Alert log says as below.
ORACLE_BASE from environment = /oracle/ora11203/app/ora11203
Thu Aug 23 15:03:36 2012
ALTER DATABASE   MOUNT
ORA-00210: cannot open the specified control file
ORA-00202: control file: '/oracle/ora11203/dbs/cntrlOMIGTEST.dbf'
ORA-27037: unable to obtain file status
HPUX-ia64 Error: 2: No such file or directory
Additional information: 3
ORA-205 signalled during: ALTER DATABASE   MOUNT...In init.ora of 11g (which is copied from 10g) ,i have commented our control file path entry.
Kindly assist me as i am doing upgrade for the first time.
Thanks
Edited by: user10698496 on Aug 24, 2012 2:47 AM

Hi,
Issue of sqlplus is solved after setting proper LD_LIBRARY_PATH.
But eve after that startup upgrade showing same error.
sqlplus '/as sysdba'
SQL*Plus: Release 11.2.0.3.0 Production on Thu Aug 23 16:22:16 2012
Copyright (c) 1982, 2011, Oracle. All rights reserved.
Connected to:
Oracle Database 11g Enterprise Edition Release 11.2.0.3.0 - 64bit Production
With the Partitioning, OLAP, Data Mining and Real Application Testing optionsSQL> startup upgrade
ORACLE instance started.
Total System Global Area 1636892672 bytes
Fixed Size 2183056 bytes
Variable Size 1090519152 bytes
Database Buffers 536870912 bytes
Redo Buffers 7319552 bytes
ORA-00205: error in identifying control file, check alert log for more info
Do i copy control file from 10g home and place in in 11g path and mention it in init.ora before upgrade?
Thanks

"Failed to load excel file" an Error Message while running TDS upgrade util

Dear All,
"Failed to load excel file" an Error Message while running TDS upgrade utility when clicking on CHECK DATA.
Please help me out on this!!!!!!!!!!!!
Thanks..........

Not all data can be exported to Excel easily. Especially if the query result is huge or there are special characters in the query results. You may try the most updated version.
Thanks,
Gordon

Error encountered: An unknown error occurred while access the upgrade file.

Hi all,
I was upgrading my call manager subscriber server from
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
7.1.3.10000-11 build to 8.0.2.41006-1 build, got the following error and the upgrade failed,
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;
mso-bidi-font-family:"Times New Roman";
mso-bidi-theme-font:minor-bidi;}
Status: Error encountered: An unknown error occurred while access the upgrade file.
While the same upgrade was successful on the pub.
Need help.

Brad,
I've seen that a number of times with 7x upgrade files. I would like to say it's consistent but it hasn't always been. I've done a number of upgrades and sometimes I would run across that issue and other times, I would not (there would be multiple files in the SFTP path). After a few times, I just started always putting my upgrade file in a dedicated folder.
Good catch...and you're not alone in experiencing it.
Hailey

Since upgrading to Maverick I'm unable to open any indesign files (receiving error code 4).

I decided to uninstall, then redownload from Creative Cloud, but my Adobe Application Manager tries to launch and quits unexpectedly, over and over. I restarted my computer, but that wasn't helpful. I was considering uninstalling all of CC, but I'm concerned about the application manager issue inhibiting me from using any programs. Illustrator is working fine after an update...Help! I'm on deadline

I had the same problem. Brand new Mac Pro with a fresh installation of Creatve Cloud.
ID CC couldn't open CS6 files. Error code 4. As luck would have it I still have CS6 on an another Mac. When I have opened the file there and then did a Save As (CS6 file with another name) everything worked great. Strange.
But now with the latest ID CC update it seems to work fine to open CS6 files without error code 4.
I hope you managed to solve your problem in time?

Web-Disk on OSX 10.9 Give me this error: "Finder got an error: Network file permission error."

Previously I was using OSX 10.8 and Web Disk was working great.
Since I upgraded to OSX 10.9 Web Disk Dont Attach to my compputer and give me this ERROR:
FInder got an error: Network file permission error.
When I got this ERROR first time I searched GOOGLE and found this link: http://cammodude.blogspot.no/
And I did:
To force all connections to be SMB1:
Open A terminal window
paste in the following line followed by the return key(should be all on one line):
echo "[default]" >> ~/Library/Preferences/nsmb.conf; echo "smb_neg=smb1_only" >> ~/Library/Preferences/nsmb.conf
What the command does:
Creates a file called nsmb.conf in your home directory at the path ~/Library/Preferences/nsmb.conf.
Adds directives to force SMB connections to use the SMB1 protocol. This is slower but stable.
Then I could use Web Disk on OSX 10.9 after executing this command in Terminal.
But now I restarted my Macbook and now Im NOT able to connect to Web Disk and get the same ERROR.
FInder got an error: Network file permission error
After trying 100 times it attaches 1 time but then show this ERROR:
Can't get <<class cdis>> "my.server.com/2078" of application "Finder".
If this happen then I can see the files in Finder and see the Contents and Size of files but if I open a PHP file in BBEdit then it shows BLANK.. But actually it is NOT blank.
Now Im stuck How can I solve this? All help is highly appericated..
Thank you so much...

Hi,
Make sure to chmod the app, something like this :
chmod -Rf 777 secure_site_WebDisk.app
(in my case the CPanel provided the app for my OSx version.)

SharePoint 2013 site collection 'upgrade completed with errors'

Hi All,
I am in process to upgrade SharePoint 2010 to SharePoint 2013 with all steps as mentioned in TechNet.
I was able to get all the SP2010 UI in SP2013 environment. However, when I navigated to top level site and clicked on “Site
Collection health checks”. In SP2010 environment I never used (as Farm Admin) any Video content type. It belongs
to out-of-the-box "digital asset content types" and cannot be deleted.
Therefore I changed the name of Video to our department name like "Video - Company" and ran the site collection health check again. This time there was no conflict for content types.
After ran the site collection upgrade I got following error.
-------------------------------------------START------------------------------------------
05/05/2014 14:34:28.66 OWSTIMER (0x1474)
0x123C SharePoint Foundation Upgrade
SPFeatureDefinition aj2bj
ERROR Feature upgrade action 'AddContentTypeField' threw an exception upgrading Feature 'CTypes' (Id: 15/'695b6570-a48b-4a8e-8ea5-26ea7fc1d162') in Site 'http://sp13fe01-dev': Field type
Rating is not installed properly. Go to the list settings page to delete this field.
32d48d9c-70d4-f09a-6073-526808f844be
05/05/2014 14:34:53.04 OWSTIMER (0x1474)
0x123C SharePoint Foundation Upgrade
SPSiteWssSequence2 ajy6m
ERROR Feature upgrade incomplete for Feature 'CTypes' (Id: 15/'695b6570-a48b-4a8e-8ea5-26ea7fc1d162') in Site 'http://sp13fe01-dev'. Exception: Field type Rating is not installed properly. Go to the list settings
page to delete this field. 32d48d9c-70d4-f09a-6073-526808f844be
05/05/2014 15:18:43.95 OWSTIMER (0x1474)
0x123C SharePoint Foundation Upgrade
SPManager ajxoe
ERROR RunUpgradeSiteSession [SPSite Url=http://sp13fe01-dev] failed.
32d48d9c-70d4-f09a-6073-526808f844be
05/05/2014 15:18:44.16 OWSTIMER (0x1474)
0x123C SharePoint Foundation Upgrade
SPManager ajxoe
ERROR Exception: Upgrade completed with errors. Review the upgrade log file located in C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\15\LOGS\SiteUpgrade-20140505-143330-61.log. The
number of errors and warnings is listed at the end of the upgrade log file.
32d48d9c-70d4-f09a-6073-526808f844be
05/05/2014 15:18:44.16 OWSTIMER (0x1474)
0x123C SharePoint Foundation Upgrade
SPManager ajxoe
ERROR at Microsoft.SharePoint.Upgrade.SPUpgradeSession.CheckPoint() at Microsoft.SharePoint.Upgrade.SPUpgradeSession.LogEnd() at Microsoft.SharePoint.Upgrade.SPManager.RunUpgradeSiteSessionCore(Object
lockObject, SPSite site, SPUpgradeOperationFlags upgradeOperationFlags, Boolean checkConcurrentSiteUpgradeSessi
32d48d9c-70d4-f09a-6073-526808f844be
-----------------------------------END-------------------------------------
Feature ID 695b6570-a48b-4a8e-8ea5-26ea7fc1d162 is Standard Content Type Definitions https://social.technet.microsoft.com/wiki/contents/articles/7695.sharepoint-2010-list-of-features-id-displayname-and-scopes.aspx.
Any expert to solve the issue??
Thank you.
regards,
Aroh Shukla

Hi All and Inderjeet,
Thanks for your reply and pointers.
I did follow the steps as mentioned in the links above. I used some third party solutions but not for any Video solution. I was able to successfully migrated the SP2010 (WSS_Content) to SP2013 (WSS_Content) environment a few weeks back with exactly same
third party solutions and no site collection error:
I renamed the default and out-of-the box video site content type as shown:
I ran the "Site Collection Health Check" and did not receive any error as in my second screenshot.
But, after upgrade the Site Collection Upgrade and got the same errors.
I don't know if there is any SharePoint Server 2013 patch gave this error as I keep run the Windows Server 2012 (not running R2) and SharePoint Server 2013 regularly.
Can suggest how to resolve this error?
Many Thanks!!
--Aaroh
Aroh Shukla
The same here. Opening a support ticket with MS.

End of file 16072 error encore V 1.5.1.42735

I've been at this awhile and usually don't have much trouble so this is beginning to make me a little cranky. I used to get this error once in a while for the usual reasons (vid and audio not same length and mismatch on time/duration on animated buttons). Latley it has started to come up on every single project and seems way random.
Here is the typical scenario. I Export a dozen or so movies from PPro 1.5 at MS DV AVI. I import as timeline in Encore 1.5.1. I use automatic transcode and build the DVD as an image on my HD to test. I get the end of file 16072 error.
This is how a I trouble shoot. I create a new Encore project called test. I import the .m2v and the .wav files from the Transcodes folder of the Encore project one at a time. In this way I avoid retranscoding the movie saving a little time. The test project has no menus or buttons and only one timeline set as first play. I build a dvd image on my HD one at a time until I get the same error in the "test" project. I then go back in PPro and work on the the Timeline that I exported the movie from. Sometimes I can just delete the last clip from the timeline and the error goes away. Then I edit the last clip back in, re-export and retest it. Most of the time it is then OK. If it is I then bring it back into the Encore project I was working on in the first place and works. Other times that does not work and I can keep going back one clip at a time until I find the problem or sometimes it is just quicker to re-edit the whole section of source material into a new timeline.
The project I am working on right now started out as seven hours of DV. I am working on the third DVD I created from it after editing down to about three hours of final footage broken up into about 36 timelines. This last Encore project has 14 timelines and three of them produce the error when testing. I just fixed one of them by deleting the last clip and testing. The other two are next up but jeeze this is getting old. No motion menus or animated buttons. The problem is with the .avi as in the test project I use it is the only timeline and set to first play with no menus or buttons.
I am looking for some informed advice from someone who has specific experience with this error and has whipped it. I have read more than a few posts from people that have gotten this error and with most it is because the material they are working with has caused it with good reason. That does not seem to be the case with my projects. I edit the same way, export the same way from PPro. I import in Encore and build basically the same project over and over. Why would I get this seemingly random error. Can I avoid it?
I have the Adobe Video Collection Professional, paid a ton for it and it does everything I need. I can't upgrade with out building an entirely new system to run the new software anyway and the money is not there for it.
I have 39 hours of video I need to edit into hundreds of timelines and this error is eating me alive. This latest project with 7 hours has had days added to it because of this error. Please help me learn solve ar avoid it.
Thanks in advance,
Mark

I wonder if there could be some slight Durational difference between the muxed streams, since the Audio is in Audio Units and the Video is in Timecode. Just a sliver of difference *could* yield a problem.
I've read of similar with other muxed sources but never a definitive answer on why En does not pick up and correct this, or how it could occur with the Export from PrPro, or other NLE. Still, it does seem to happen on occasion.
Also, I usually have a bit of Black Video at the Head, and then some at the Tail, so in PrPro, my Video Timeline is always a bit longer, than my Audio Timeline. As there is no Audio signal at the end, PrPro can deal with it perfectly. Will have to try some muxed sources (not my normal workflow) to see if there is something else afoot.
Just thinking here,
Hunt

Not able to run adadmin adfter installing R12 Upgrade file system

Sawwan,
Now we are doing 11i apps to R12 upgrade single node, before we did database upgrade 9i to 10.2.0.4,
I successfully installed R12 upgrade file system with out any errors, i have chagned the
new Installation creates APPL_TOP, COMMON_TOP, INST_TOP and 10g Oracle Home
i moved the new environment file into .bash_profile
mv .bash_profile .bash_profile_11.5.10
Iset the R12 environment , When ever i tried to run adadmin system manager password is not taking its giving error
[applupg@peabody appl]$ adadmin
Copyright (c) 2002 Oracle Corporation
Redwood Shores, California, USA
Oracle Applications AD Administration
Version 12.0.0
NOTE: You may not use this utility for custom development
unless you have written permission from Oracle Corporation.
Your default directory is '/u01/R12/apps/apps_st/appl'.
Is this the correct APPL_TOP [Yes] ?
AD Administration records your AD Administration session in a text file
you specify. Enter your AD Administration log file name or press [Return]
to accept the default file name shown in brackets.
Filename [adadmin.log] :
************* Start of AD Administration session *************
AD Administration version: 12.0.0
AD Administration started at: Sat Apr 18 2009 06:12:52
APPL_TOP is set to /u01/R12/apps/apps_st/appl
Backing up restart files, if any......Done.
Your previous AD Administration session did not run to completion.
Do you wish to continue with your previous AD Administration session [Yes] ?
You are about to use or modify Oracle Applications product tables
in your ORACLE database 'upg'
using ORACLE executables in '/u01/R12/apps/tech_st/10.1.2'.
Is this the correct database [Yes] ?
AD Administration needs the password for your 'SYSTEM' ORACLE schema
in order to determine your installation configuration.
Enter the password for your 'SYSTEM' ORACLE schema: manager
...Unable to connect.
AD Administration error:
The following ORACLE error:
ORA-12541: TNS:no listener
occurred while executing the SQL statement:
CONNECT SYSTEM/*****
AD Administration error:
Unable to connect to 'SYSTEM'; password may be invalid.
AD Administration needs the password for your 'SYSTEM' ORACLE schema
in order to determine your installation configuration.
Enter the password for your 'SYSTEM' ORACLE schema:
Enter the password for your 'SYSTEM' ORACLE schema:
Before running R12 adadmin is there nessary 11i apps servicess should up or down..
Edited by: HumanDBA on May 5, 2009 12:26 PM

Sawwan,
As a oracle user i am able to see the tns_admin home dir
[oraupg@peabody upg_peabody]$ echo $TNS_ADMIN
/stage/10gsoftware/network/admin/upg_peabody
[oraupg@peabody upg_peabody]$
After installing R12 uprade file system i am able do the tnsping
[applupg@peabody appl]$ tnsping upg
TNS Ping Utility for Linux: Version 10.1.0.5.0 - Production on 18-APR-2009 06:26:49
Copyright (c) 1997, 2003, Oracle. All rights reserved.
Used parameter files:
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION= (ADDRESS=(PROTOCOL=tcp)(HOST=peabody)(PORT=1526)) (CONNECT_DATA=(SID=upg)))
TNS-12541: TNS:no listener
[applupg@peabody appl]$
[applupg@peabody appl]$ sqlplus apps/xxxx@upg
SQL*Plus: Release 10.1.0.5.0 - Production on Sat Apr 18 06:29:45 2009
Copyright (c) 1982, 2005, Oracle. All rights reserved.
ERROR:
ORA-12541: TNS:no listener
Enter user-name:
========================================
Sawwan
after installing i am trying to apply R12.AD.B patch, do we need to apply this patch in 11i fiile system or New R12 file system, for 11i file system i am not getting any issue, but when ever i set the R12 new file system enviroment file then only i am not able to connect the database,i have changed new port numbers in R12 file system, is that causing any issues..?
Edited by: HumanDBA on May 5, 2009 12:37 PM

File adapter error after updating to SP19 (INBOUND_BINDING_ERROR)

File adapter error after updating to SP19 (INBOUND_BINDING_ERROR)
Hi all,
im having some troubles after the installation of SP19 (from SP16 in NW04) with File Adapter (File->Idoc scenario).
In message monitoring (Adapter Engine), I have several messages with status "System Error". The error text is :
Received XI System Error. ErrorCode: INBOUND_BINDING_ERROR
ErrorText: ErrorStack: Error in sender agreement for party '', service 'LEGACY_DEV', interface namespace 'http://XXXXX.com/XXXXXX', interface 'INTERFACE_OB' No sender agreement found for , , , , ,
Im sure that the Integration Directory settings have not been changed. So I tried the following, but the problem persists:
- Deactivation/Activation of File Adapter channel
- check that user XIISUSER is not locked
- checked SXI_CACHE (it seems ok)
- Many CPA full refresh
- Dummy modifications of File Adapter channels (a dummy modification of the description)
- Reboot J2EE
I've seen that someone else had problems after upgrading to SP19. I'd really appreciate any suggestion of how to solve my issue.
Thank you
Manuel

Hi Prabhu,
I've already tried to restart server, but nothing happened. (Before update to SP19, the interface worked well).
This is the error log from message monitoring:
 2007-01-16 16:37:34 Success Channel cc_File_Snd_Bolle: Entire file content converted to XML format
2007-01-16 16:37:34 Success Send binary file "BOLLE_20061229142059.CSV" from FTP server "AS810T:/sapinbound", size 8733 bytes with QoS EOIO
2007-01-16 16:37:34 Success Application attempting to send an XI message asynchronously using connection AFW.
2007-01-16 16:37:34 Success Trying to put the message into the send queue.
2007-01-16 16:37:35 Success Message successfully put into the queue.
2007-01-16 16:37:35 Success The application sent the message asynchronously using connection AFW. Returning to application.
2007-01-16 16:37:35 Success The message was successfully retrieved from the send queue.
2007-01-16 16:37:35 Success File "BOLLE_20061229142059.CSV" successfully archived on FTP server "AS810T" as "/sapinbound/bolle/20070116-163735-245_BOLLE_20061229142059.CSV"
2007-01-16 16:37:35 Success The message status set to DLNG.
2007-01-16 16:37:35 Error Received XI System Error. ErrorCode: INBOUND_BINDING_ERROR ErrorText: ErrorStack: Error in sender agreement for party '', service 'LEGACY_DEV', interface namespace http://XXXXX.com/XXXXXX', interface 'INTERFACE_OB' No sender agreement found for , , , , ,
2007-01-16 16:37:35 Error Transmitting the message to endpoint http://SERVERNAME:8000/sap/xi/engine?type=entry using connection AFW failed, due to: com.sap.aii.af.ra.ms.api.RecoverableException: INBOUND_BINDING_ERROR:. 
2007-01-16 16:37:35 Success The asynchronous message was successfully scheduled to be delivered at Tue Jan 16 16:42:35 CET 2007.
2007-01-16 16:37:35 Success The message status set to WAIT.
2007-01-16 16:42:35 Success Retrying to send message. Retry: 1
After this, the system try to resend the message, and the same error appears several times.
Ty,
Manuel

Cs4 opens cs3 files with errors

Here's a big heads up for anyone considering upgrading to cs4 - don't! I've been working on a cs3 project and decided to upgrade to cs4 for the extras in the 3D toolset. All the Adobe propoganda implies this can be achieved no problem, as did soemone on telephone tech support. Perhaps I didn't clearly ask 'can I open my cs3 file in cs4'. I can BUT the clips are very much 'out of synch. I'll lick my wounds and go back to finishing in cs3 but don't purchase cs4 if you think you can seamless import your sc3 project. Because it seems you very much can not!

Dennis,
Many thanks.
Date: Thu, 11 Feb 2010 05:21:44 -0700
From: [email protected]
To: [removed]
Subject: Premiere Pro cs4 opens cs3 files with errors
Jarrod,
As I've stated here in this forum, we're trying to transition Adobe technical support to a new organization and providing the best support we can to our customers. That being said, it is a long and sometimes painful process, which is why I am here on the forums at times to lend some support. This doesn't help you and you might not even care so...
Here's a couple of suggestions:
1. make sure your software is updated (Premiere Pro 4.2.1) by going to help>updates
2. clear your prefs - http://blogs.adobe.com/genesisproject/2009/11/having_weird_behavior_with_an.html
3. try importing (ctrl-I) a CS3 project into CS4
Try these things and let me know how you make out. Also, it would be very helpful if you told us about your system and the specs. I've posted about the importance of 64-bit and lots of memory many times. You can find one link here: http://blogs.adobe.com/genesisproject/2009/03/64_bit_os_and_adobe_products.html
The future of Premiere Pro is 64-bit only: http://blogs.adobe.com/genesisproject/2009/10/its_official_64bit_is_the_futu.html
Beyond that if you'd like me to look into your case, please post your case # here or in a private message to me and I'll gladly look at it.
I sense your frustration and its understandable - give us a chance to help you.
Dennis
>

Upgrade file pattern error

Similar Messages

Maybe you are looking for