Upgrade Firmware and storage disconnect

During the firmware upgrade to version 2.0.2q everything went well until I upgraded the 6124 Interconnects. I first upgraded the secondary then the primary. During both upgrades the ESX Hosts reported loss of access to the datastore attached to the hosts. The guests continued to ping which leads me to believe that the host did not really loose access because the guests run from the datastore reported as lost in vCenter. Within 8 mins or so the storage error corrected. My question, is this normal behavior. Has anyone else seen this behavior during interconnect upgrades?

Hi Joey:
Thank you for your reply. Yes multi pathing is in place and failover does occur. This was my test environment I did first. I just noticed that of three hosts two reported redundancy link lost (which is normal) but one showed redundancy link and the managment network lost and access to the datastore for VM guests although VM guests continuded to ping normally. The host however was not pinging in fact as being reported.
Anyway, I went forward with production last night and all went as expected with only redundancy link lost during interconnect updates/reboots. No problems. So, I believe my test environment has a connection between the two interconnects switched around from when I first set it all up. There have been some others working in my test area.
Thanks again,
Fred

Similar Messages

Bought brand new ipad 2, upgrading firmware and error 3194

I just got a brand new ipad 2 32gb wifi only. I want to upgrade firmware and i get error 3194. I tried changing host file and other things like that. I am really sick of this problem please help me if you can.
Im currently on 4.3.5 and want to go to 5.0

Posting in all caps is considered to be shouting at someone here in the Apple Support Communities and a very poor lack of manners. It will also likely bring about folks ignoring you.
Then you might try some of the approaches in this article;
http://support.apple.com/kb/ts1275

MacBook4.1 early 2008 - Upgrade Ram and Storage

Hey Guys, my English is not good, so please, take me patient = )
I have a Black MacBook early 2008, ( MacBook4,1 ). I want to do a Ram and HD upgrade.
I was reading
https://discussions.apple.com/thread/3226716?start=0&tstart=0
but i am not sure if i can upgrade to 8gb in Lion, and wich Hard Disk is good for me.
Any way, I am thinking whats the better option: Do a Upgrade or buy a new MacBook.
I know, i cant upgrade for 10.8 or 10.9 but i want to know if i can use this machine for a ltlle more of time.,
Please, tell me, in your opinion, whats the better option.
If you can, please, indicate how can i upgrade 4, 6, or 8GB acording your suggest. I am not sure
if i can put 8G Ram in the machine. (btw, that will be amazing)
For HD i have no idea for compatibles disks with this model, (size, etc)
My intension is use this apps: Autocad, Win8 with bootcamp, Photoshop, Office, etc...
I''ll be happy paying until 400$ for Upgrades.
I was reading for problems with 8gb in macbooks 4,1, but i dont know...
Thanks anyway!
Spec sys:
Hardware Overview:
Model Name:          MacBook
Model Identifier:          MacBook4,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2,4 GHz
Number of Processors:          1
Total Number of Cores:          2
L2 Cache:          3 MB
Memory:          2 GB
Bus Speed:          800 MHz
Boot ROM Version:          MB41.00C1.B00
SMC Version (system):          1.31f1
Serial Number (system):          W8******0P2
Hardware UUID:          0A4651CF-CFA4-5824-8223-0D7EFF41F550
Sudden Motion Sensor:
State:          Enabled
Ethernet:
Type:          Ethernet
Hardware:          Ethernet
BSD Device Name:          en0
IPv4:
Configuration Method:          DHCP
IPv6:
Configuration Method:          Automatic
Ethernet:
MAC Address:          00:22:41:2f:fb:e9
Media Options:
Media Subtype:          Auto Select
Proxies:
Exceptions List:          *.local, 169.254/16
FTP Passive Mode:          Yes
Service Order:          0
System Software Overview:
System Version:          Mac OS X 10.7.5 (11G63)
Kernel Version:          Darwin 11.4.2
Boot Volume:          Odin
Boot Mode:          Normal
Computer Name:          Hernan’s MacBook
User Name:          Hernan Rosas (hernan)
Secure Virtual Memory:          Enabled
64-bit Kernel and Extensions:          No
Time since boot:          17 minutes
<Edited by Host>

The model 4,1 (Early 2008) can use 6gb of 200 pin 667mhz PC2-5300 RAM
These are good online stores for Mac compatible RAM
OWC 667Mhz RAM
http://eshop.macsales.com/shop/memory/MacBook/DDR2/ - They offer Mac tested RAM at very good prices.
Crucial Memory http://www.crucial.com/ - good place to buy RAM from all over the world. They also have an excellent memory selector that allows you to choose memory based on your computer's model
Data Memory Systems http://www.datamemorysystems.com/apple-memory.asp - another good, cheap place to buying RAM if you live in the U.S.
Here are instructions on replacing RAM in a MacBook with a removable battery. http://homeoffice.consumerelectronicsnet.com/articles/viewarticle.jsp?id=44404
If you don’t have the tools to open up the MacBook OWC has a set for $5.
http://eshop.macsales.com/item/OWC/TOOLKITMHD/

Linksys e3000 occasionally suddenly rebooting and/or disconnecting due to overheating

I recently purchased a Linksys e3000 router and was experiencing intermittent disconnects and reboots (about once every 5 minutes). After digging through several forum posts I was able to discover that the router was most likely overheating. I felt the bottom of the router and found that it was indeed very hot, so I placed a fan next to it and exposed some more of the ventilation. Its been about an hour so far but it appears to be performing fine.

When any electronic device reboots on its own, it is almost always overheating, or has a virus. Since this is a router, you could try upgrading firmware, and then doing a proper hard-reset, by holding in the reset button, unplug the power (while still holding in reset) and then replug in the power. Continue to hold reset button this whole time for 30 seconds, then release, and configure router.
If problem continues, just return it or buy another.

Problem with N73 upgrade v4 and connectivity to gp...

N73 working fine especially with tomtom v6 and gps receiver, however silly me decided to upgrade firmware and on doing so, now gps receiver is found but not allowed to work. Has anyone elese had this issue with N73 upgrade and tomtom and or bluetooth. The person with a fix gets a reward in heaven!

Did you try uninstalling and then reinstalling TomTom?

No firmware and no contact with PC with zen visio

I wanted to upgrade firmware and followed an instruction that told me to rebuild firmware first and then install the firmware upgrade. The update program doesnt say it is docked - although it states docked in the Vision M screen.
Appreciate any helpMessage Edited by borge on 04-3-20070:50 PM

Ok, I am assuming that either pc suite is so buggy that no one has had a chance to emulate this or that no one has this issue other than me and everyone is synchronising their outlook contacts with their N70 and are still able to us voice Tags?
If anyone is experiencing this issue can they please let me know I am not the only person having this problem or preferably if anyone knows a fix please let me know so I can either ignore and forget ever using voice tags or allow me to use what would be a really useful feature?
I am beginning to think this may be like a Microsoft built in feature
Cheers, B

WRT54g V6, constant disconnect.. 2 week old unit.. upgraded firmware -- what the..?

I upgraded firmware to the latest(november one). I reseted both router and cable modem and all 3 computer using it.
I've tried something like 100 MTU number, and I still get the same disconnection problems.. seems the power LED is blinking while I get disconnected.
it seems this is a pretty bad router, that gets overwhelmed when you download too much on two or more computer simultaneously.
all my computers are using WIRED connections.
I need help before I terminate this unit with a large wooden club.
really need help, if linksys doesnt want to lose a customer forever.
ps:also -- whats up with the cheap 2mb flash and 8mb ram on this version? earlier version of this unit had 4mb flash and 16mb ram.. im very sad to see you guys downgrading with higher version numbers.. nice marketing!

I mean I tried 100 different MTU number from 1500 to 1000, with nothing happening..
I've sent 3 emails to support, they all say they gonna answer within 24 hours and answer to all 3 of them within days.......
( Mod note: Edited for guideline compliance. Thanks! OnnagokorO)Message Edited by Vince_02 on 01-03-2007 10:54 PM

After upgrading to 8.1 Pro from 8.0 Pro, my Storage Spaces and Storage Pool are all gone.

Under 8.0 I had three 4-terabyte drives set up as a Storage Pool in Storage Spaces. I had five storage-space drives using this pool I had
been using them for months with no problems. After upgrading to 8.1 ( which gave no errors ) the drives no longer exist. Going into "Storage Spaces" in the control panel, I do not see my existing storage pool or storage drives. I'm prompted
to create a new Pool and Storage Spaces. If I click the "Create Pool" it does not list the three drives I used previously as available to add.
Device Manager shows all three drives as present and OK.
Disk Management shows Disks 0,1,2,6. The gap in between 2 and 6 is where the 3,4,5 storage spaces drives were.
Nothing helpful in the event log or the services.
I've downloaded the ReclaiMe Storage Spaces recovery tool and it sees all of my logical drives with a "good" prognosis for recovery. I've not gone down that road yet though because it requires separate physical drives to copy everything to
and they want $299 for the privilege.
Does anyone have any ideas? I'm thinking of doing a fresh 8.1 install to another drive to see if it can see it or reinstalling 8.1 to the existing drive in the hope that it will just suddenly work. Or possibly going back to 8.0.
Thanks for your help!
Steve

Hi,
“For parity spaces you must backup your data and delete the parity spaces. At this point, you may upgrade or perform a clean install of Windows 8. After the upgrade or clean installation is complete, you may recreate parity spaces and
restore your data.”
I’d like to share the following article with you for reference:
Storage Spaces Frequently Asked Questions
(Pay attention to this part:How do I prepare Storage Spaces for upgrading from the Windows 8 Consumer Preview to Windows 8 Release Preview?)
http://social.technet.microsoft.com/wiki/contents/articles/11382.storage-spaces-frequently-asked-questions-faq.aspx#How_do_I_prepare_Storage_Spaces_for_upgrading_from_the_Windows_8_Consumer_Preview_to_Windows_8_Release_Preview
Regards,
Yolanda
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

My wifes iphone was too full to record a video so I upgraded her cloud storage to 20g and did mine at same time. Cloud is showing 15g free storage butshe still cannot take any mor photos as "not enough memory" What is the point of paying for the extr

My wifes iphone was too full to record a video so I upgraded her cloud storage to 20g and did mine at same time. Cloud is showing 15g free storage butshe still cannot take any mor photos as "not enough memory" What is the point of paying for the extr

Hello Pushtheriver,
After reviewing your post, I have located an article that can help in this situation. It contains a number of troubleshooting steps and helpful advice concerning iCloud storage issues:
Get help using iCloud storage
This may also help:
Understanding iOS device capacity
You can sync and download many different types of content on your device. Some types of content (such as music and videos) typically take more space than others (such as notes and books). The amount of space taken by an app depends on the app's purpose; complex or graphically intense apps usually take more space than simpler apps.
If your device is near its capacity, you can remove some of the less used content to make room for more.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

I upgraded my icloud storage and amount got deducted from my account but yet storage wasn't upgraded. What can i do?

I upgraded my icloud storage and amount got deducted from my account but yet storage wasn't upgraded. What can i do?

How long did you wait for the systm to catch up to your request for more storage? it can take a little while, up to an hour sometimes I have heard.
If you don't see any more room after waiting a while, try resetting your phone to see if it appears then.
If that doesn't help go here, http://www.apple.com/support/contact/ and see if they can help you out.

HT201318 I upgraded my iCloud storage capacity for a higher tier and the device does not actually reflects said upgrade. How can this be resolved since my credit card was charged

I upgraded my Icloud storage capacity to a higher tier and my Iphone does not reflect the change although my credit card was charged and the device is nor properly backup. How can this be resolved?

It seems to take up to a couple of days for the upgrade to take hold, at least that's the experience of some users. Give it 24 hours before contacting apple.
For customer service issues, go here...
https://expresslane.apple.com/Issues.action

IMac G3 won't boot after updating the firmware and upgrading the OS!

Hi! Everyone,
I have an iMac G3 333MHz (five flavors) which comes with 192MB of RAM and 6GB of hard drive. Originally, it was OS 8.5.1 installed, later upgraded to OS 9.2.2. Of course, the firmware has been updated by the appropriate method provided by the on-screen instructions before the installation of 9.2.2. After successfully updating the firmware and installing Mac OS 9.2.2, the system booted up and worked fine. However, after shutting it down and powering it up a few days later, I have encountered a critical problem:
1. At first, the iMac would chime and displayed a smiley-mac finder face.
2. No question mark appeared and the system halted because it stayed at the same screen for about 5 minutes! Also, the keyboard wouldn't respond. For instance, the LED signal light wouldn't light on when Caps Lock was pressed.
3. I assumed that this is just a typical crash and rebooted the machine via the "reset" button on the right side of the machine.
4. After restarting, well, no luck, the same condition. Therefore, I rebooted it again by using the method mentioned above.
5. The condition of sticking at the smiley-mac finder face occurred again! However, this time the iMac wouldn't chime and just displayed the mac face.
6. Another restart, well, it was getting worse... no chime and no smiley-mac finder face but a white screen.
7. I was frustrated then and shut the machine down forcefully by rebooting it again and pressing on the power bottom quickly before the screen appears. Also, I unplugged the power cord.
---------- After a few hours later ----------
8. Okay, I then plugged the power cord in and booted it up again, this time, it would chime but stuck at the white screen. => No smiley-mac finder face appeared!
9. Rebooted it again, the result was as same as step 8.
10. Another restart, the smiley-mac face finally appeared but still... stuck here and this time, no chime.
11. I then shut the machine forcefully by using the method mentioned above and let the machine rest for about a day with the power cord unplugged.
---------- After resting for a day ----------
12. I booted it up and it would chime, but no screen (the power button was orange, not green). I then forcefully shut down the machine.
13. Waited for about a minute and powered it up. This time, I tried to clear the PRAM, but no chime and gave me a white screen. => No luck! As mentioned, the keyboard's LED signal light wouldn't light on even though the Caps Lock key has been pressed.
*Note: The keyboard has been tested on the other computers and it worked. Also, I tried different USB ports to plug the keyboard in. => The USB ports were all in working condition， as I can know from the last successful start up.
14. Forcefully shut the machine down and tried to enter the Open firmware, no luck. It didn't enter and gave my a white screen.
15. Conclusion:
1) After resting for a while, the iMac would chime.
2) Rebooting too much times would cause the machine not to chime and leaded the screen to become white instead of the smiley-mac finder face.
3) However, rebooted the machine when the screen became white, the smiley-mac finder face would appear again without chime.
By the way, I could hear the hard disk spinning up so that means the hard disk is working.
Can anyone help me solve this problem? Is it related to the firmware update? Any suggestions will be appreciated! Thanks!
Andy

OK, I will try replacing the PRAM battery. Also, the PowerMac G3 and the other iMac 233MHz had the dead batteries. They are still working though... Should I replace them along with the iMac 333MHz? In case of not replacing, will they malfunction in future times? There are some symptoms on this two machines: 1. iMac 233MHz - No chime and no sound when adjusting system volume (the bi sound is not available), but iTunes and other applications can still use the audio device and output the sound via internal speakers; 2. PowerMac G3 450MHz - Will chime but sometimes hard to boot: 1) Chime but no screen; 2) No respond after pressing the power button => the power signal light won't light on. Every time I experienced this, I would open its case, pressing a small button (not quite understand what it does... anyway, just works if system halted.) near the PRAM battery and wait for about a minute, then close the case, and it boots. However, I have to reset "Date & Time"...

Hi, I've upgraded my iCloud storage and uploaded my 3000 photos. I now want to delete them from my phone. Can I still access them from the cloud of I do? If so how? Thank you in advance.m

Hi, I've upgraded my iCloud storage and uploaded 3000+ photos. Can I safely delete them from my phone and still access them from the cloud? Thank you

Hey linsfrombrandon,
The closest you will get to have your photos live in iCloud and not taking as much storage space on your iPhone is by using iCloud Photo Library. What it does is makes your Photos live in iCloud but also appear on your iPhone and other iOS devices and computers. It will be the exact same so any changes will be reflected everywhere. When they are on your iPhone, there is an option to use a compressed version. Take a look at the FAQs page and let me know if you have any other questions before making this decision to turn this on. I would also make sure that you have a safe copy of your photos before moving forward.
iCloud Photo Library beta FAQ
http://support.apple.com/en-us/HT6378
Take care,
-Norm G.

Using iPhone 3G ,Version 4.2.1,Modem Firmware 06.15.00, In this phone i was using Facebook upgraded app and Smart Sync App. Suddenly my sisiter reset all setings and now I can't use the upgraded facebook app, for smart sync is asking for IOS 4.3,Need help

Using iPhone 3G ,Version 4.2.1,Modem Firmware 06.15.00, In this phone i was using Facebook upgraded app and Smart Sync App. Suddenly my sisiter reset all setings and now I can't use the upgraded facebook app, for smart sync is asking for IOS 4.3,Need help.

Thank you for the answers so far, but I'll make one correction: I said earlier that the Boston Globe website, boston.com, does not have a mobile site, and I would need to visit their regular website on my iPhone. Actually, I just found out that boston.com has a mobile site, so I'd obviously use that instead of the regular site. By doing that, I'd save a ton of data (I think). Does that change your answers?

I have a ipod touch 1G and I would like to upgrade firmware from 1.1.5 to the latest 3.x. How can I do it? Please help. thanks

I have a ipod touch 1G and I would like to upgrade firmware from 1.1.5 to the latest 3.x. How can I do it? Please help. thanks

vinayakfrommonroe wrote:
I have a ipod touch 1G and I would like to upgrade firmware from 1.1.5 to the latest 3.x. How can I do it? Please help. thanks
Hi: Check out the Apple article below.
https://discussions.apple.com/message/15112985#15112985
Stedman

Upgrade Firmware and storage disconnect

Similar Messages

Maybe you are looking for