Upgrade from 4x2 GB to 2x8 GB Ram results in strange Windows 7 64bit behavior

I wanted to upgrade my System, swapped the 4x2 GB (Adata 1600G) to 2x8 GB (G.Skill F3-2133C9D 16GXH) Ram to the Dual Channel Slots (2 x Blue)
The System asks me to enter Setup with F1 recognizing the mem change.
I have OC Genie active and tried it later without.
When I boot to Windows with the new RAM my NVIDIA Card has a yellow exclamation mark in my device list. Also NVIDIA Software can`t access the card telling me I would have not such an device active. I tried to reinstall the drivers without success.
I tried a couple of changes in bios and rebootet, but gave up after 40 Minutes of experimenting.
After I went back to my old RAM the system runs smooth like always.
Now I hope someone here can give me the right advice what to do, or ì`ll sent them back to the shop.
System:
MSI Z68A-GD80 (B3) (MS-7672) (Bios V20.1 01/09/2013)
Intel Core I5-2500k @ 4200
NVIDIA N560GTX-Ti
New Ram: G.Skill RipjawsX F3-2133C9D 16GXH
Old Ram: A-data 1600G @ 667 MHZ
What I did:
1 G.Skill Ram in DIMM1 works good, also with OC
changed the other one G.Skill module workd ok (to be sure both are ok)
as soon as I add the second RAM NVIDIA Card doesnt work correctly, some programs give me strange warnings, blue screens, random crashes.
I choosed DIMM1 + 3 (Blue) or DIMM2 +4 and all other positions with no good result.
Even with default settings no luck.
i get the following error on my nvidia card in the device manager
"Windows cannot verify the digital signature for the drivers required for this device. A recent hardware or software change might have installed a file that is signed incorrectly or damaged, or that might be malicious software from an unknown source. (Code 52)"
Is it an error on the motherboard ?
How can I proof that? Any tools ? I`m really out of ideas ...
Thank you

Quote from: cekay on 29-March-13, 00:58:11
thank you. that`s what I had in my back mind
I didn`t thought that the performance increase is that less. any reviews you can recommend ?
Here is the memory scaling on a Core i7 2600K:
As you can see, in both cases (non-3D and 3D apps) the performances boost is close to zero.
So again: for all the current Core i5 / Core i7 processors, DDR3-1600 is the best match.
Above that, nothing but troubles.

Similar Messages

MOVED: Upgrade from 4x2 GB to 2x8 GB Ram results in strange Windows 7 64bit behavior

This topic has been moved to Intel Core-iX boards.
https://forum-en.msi.com/index.php?topic=167714.0

Quote from: cekay on 29-March-13, 00:58:11
thank you. that`s what I had in my back mind
I didn`t thought that the performance increase is that less. any reviews you can recommend ?
Here is the memory scaling on a Core i7 2600K:
As you can see, in both cases (non-3D and 3D apps) the performances boost is close to zero.
So again: for all the current Core i5 / Core i7 processors, DDR3-1600 is the best match.
Above that, nothing but troubles.

Can I upgrade from 1 gb to 2 gb RAM ?

Hi All:
I have a client with 2 17in PBs, one 1ghz and the other 1.33ghz, and both have 1 GB RAM installed, Can she upgrade from 1 gb to 2 gb RAM ? ( via 2 X 1GB modules ). Even though the manual says the maximum RAM is 1 GB. Also what type of memory is it and what is a ballpark cost?
Thanks
PS if possible i would like to hear from people that have done this.

I upgraded my 1.67 PB when I bought in January from 512MB to 2 GB. I purchased Mac RAM at DMS (http://www.datamem.com/AMM12.asp). I bought 2 1GB modules for 100.00 each which was less than half of what Apple wants for memory.
Haven't had any issues whatsoever and I run some fairly intensive apps (Apeture, FC Studio). The only app that has been a bit flaky is Lotus Notes (6.5.4) which seems to fail on startup every once and a while...
-Scott
17" G4 PowerBook Mac OS X (10.4.4)

Upgrade from 10.2.0.1 32bit to 10.2.0.4 64bit windows

This scenario i have planned to make an attempt of my own..
1) Plan to Migrate existing database from ( 10.2.0.1 ) 32bit to (10.2.0.4) 64bit database
2)Existing DB is No archive mode,
3)OS windows server 2003 Enterprise sp 2(32 bit)
Migrate DB config
1)Os windows server 2008 Enterprise 64 bit
I need help from oracle gurus!!! how to migrate existing DB Upgrade from 10.2.0.1 32bit to 10.2.0.4 64bit windows
1)how to take backup?
2)how to upgrade oracle version?
3)proper step to follow completed this task successful
For database migration and upgrade activity...
share your suggestions please
Regards,
Venk@t

How big is the database ? How much downtime can you afford ? One option is to install 10.2.0.1 on the target, apply the 10.2.0.4 patch, create an empty instance on target, then export the database from the source and import into target.
Pl be aware that 10.2.0.1 thru 10.2.0.4 are on sustaining support and 10.2.0.5 is on extended support (if you have paid the extended support fees). Why not upgrade to 11gR2 ?
HTH
Srini

Have photoshop 6 on a dead pc laptop with windows XP. Have a pc laptop that has been upgraded from Vista 64 bit (where photshop wouldn't install) to windows 7 professional 32 bit (clean install). Photoshop still won't install. Also having reinstallation

I have photoshop 6 on a dead pc laptop with windows XP. Have a pc laptop that has been upgraded from Vista 64 bit (where phootshop 6 wouldn't install) to windows 7 professional 32 bit (clean install). Photoshop still won't install. Also having reinstallation issues with pse6 on this same pc. Pse6 was installed and working on vista 64bit version of the OS, now won't install on rebuilt windows professional 7 32bit (keeps giving me serial number not valid errors). I'm not trying to pirate these programs. Just want to reinstall them.

you need,
Windows 98, Windows 2000, Windows NT 4.0 with Service Pack 4, 5, or 6a, or Windows Millennium
Microsoft Windows 98/Millennium/2000/NT 4.0 (Service Pack 4, 5, or 6a required)

It's possbile to upgraded from win2003 x64 sp2 which installed SCOM 2007 R2 into windows 2008 R2 directly?

current OS: windows 2003 R2 x64 SP2
current SCOM version: SCOM 2007 R2
current database version: SQL Server 2005
it's possbile to upgraded from win2003 which installed SCOM 2007 R2 into windows 2008 R2 directly without reconfiguartion SCOM?

Hi,
And as far as I know, in-place operating system upgrade could work, but there is no document about this. Please take backup before doing upgrade.
If you want to in place upgrade the OS, we can simply move SCOM databases to new servers and rebuild management servers one at a time. the downtime for SCOM would be very minimum if the management group has the capacity for agents to report to failover
management servers while the primary MS is getting rebuilt. You do not have to perform in place upgrade on the OS to keep SCOM.
Based on your need, I would like to suggest you add a Windows 2008 R2 as additional management server for your management group. And if possible, please also upgrade your SQL 2005 to SQL 2008.
Here is a thread for your reference:
http://social.technet.microsoft.com/Forums/systemcenter/en-US/4713e303-76a7-4954-9494-55565757d65e/scom-server-os-and-sql-upgrade-from-2003-to-2008-r2
Regards, Yan Li
Dear Yan, Since rebuild/config SCOM Server is very complicated so it's better that I can just upgraded OS into windows 2008 R2 without do anything else.

Will Upgrading from 4 GB to 8 GB RAM Improve Performance

I have a 2009 2.0GHz Mac Mini with 4GB RAM. I use Photoshop CS4 and Lightroom 3 to process digital images. Lately, I'm processing higher megapixel files. I've gone from 10MP to 15MP and 18MP and would like processes to go faster.
Do you think that I'll see a significant gain in performance going from 4 to 8 GB RAM?

You may see some performance increase, but Photoshop CS4 can't address more than 4GB of RAM (it actually won't use that much, but I don't remember the exact figure), so expanding to 8GB won't be of as much benefit as it would if you upgraded to CS5 which is a 64-bit application and so is capable of addressing more RAM.
Regards.

Is it worth the $ to upgrade from 1.5Gb to 2Gb of RAM?

I have a G4 Dual 450 AGP with 1.5Gb of RAM. I am working on a large catalog. I use InDesign and Photshop a lot. Will I even notice the extra 512 Mb enough to justify the purchase? Thanks.

Hi
You could try using the Activity Monitor application located in the Applications\Utilities folder to monitor your existing memory usage whilst you perform your work. The following article explains how to interpret the information shown:
http://docs.info.apple.com/article.html?artnum=107918
As already mentioned a processor upgrade may be more beneficial. IMHO you get the most bang for the buck with a mid range processor upgrade, perhaps a single 1.4 - 1.5GHz 7455 based one, e.g.
http://www.sonnettech.com/product/encore_stg4.html
http://eshop.macsales.com/shop/accelerators/OWC-Mercury-Extreme/

Upgrading from 512 to 1.5 GB RAM?

Currently I have a Macbook Pro with just 512 MB of RAM. I was planning on buying this RAM from newegg:
http://www.newegg.com/Product/CustratingReview.asp?Item=N82E16820231066
Is it ok to have both a 1 GB and a 512 MB RAM stick in the computer at once, or should I have two of the same size RAM?

For best RAM performance (Dual channel mode) it's ideal to have two sticks of the same size; 2x512MB or 2x1GB and then you get about 6% benefit.
However, the performance gain is small compared to having more RAM available so, 1.5GB is better than 1GB for things like Aperture or if using Rosetta.

Oracle upgrade from 32-bit Oracle 9i to 64-bit Oracle 10g (Windows 2003 R2)

Hello Gurus,
Existing I have SAP R/3 4.7 200 Oracle 9i Windows 2003 32bit
I want to upgrade Hardware to x86 EMT64bit
I would like to upgrade to 64-bit Oracle 10G from 32-bit Oracle 9i. runs on Windows 2003 32bit. Target DB is Oracle 10G on x64 Windows (EMT64 hardware) on Windwos 2003R2 64bit. & Add Solution manager to new System
Please give me any advise which is the better way of upgrading Oracle 10g. Or better yet, please advise a safe way of upgrading to Oracle 10g from 9i
Please guide me about request shipping DVD For This Solution to my site
Many thank in advance
Kuekul

Hi
You can download Oracle 10g from service market place www.service.sap.com>downlaods>Installations and Upgrades-->
Installations and Upgrades - Entry by Application Group>SAP NetWeaver>SAP NetWeaver7.0>Installation and upgrade>windows server-->oracle check for below software and download it
EXE 51031678_1 ORACLE RDBMS 10.2 Windows 1 of 5
RAR 51031678_2 ORACLE RDBMS 10.2 Windows 2 of 5
RAR 51031678_3 ORACLE RDBMS 10.2 Windows 3 of 5
RAR 51031678_4 ORACLE RDBMS 10.2 Windows 4 of 5
RAR 51031678_5 ORACLE RDBMS 10.2 Windows 5 of 5
ZIP 51033272 ORACLE 10.2 Client
ZIP 51036971_2 ORACLE RDBMS Patch 10.2.0.4 Windows Server on IA32 32bit
ZIP 51036971_3 ORACLE RDBMS Patch 10.2.0.4 Windows Server on IA64 64bit
ZIP 51036971_4 ORACLE RDBMS Patch 10.2.0.4 Windows Server on x64 64bit
Regards
Uday

Effects of Oracle Upgrade from 10.2.0.1(32bit) to 10.2.0.4(64bit)

We are planning a Database Server upgrade. The current configuration is Red Hat Linux 4 (32Bit) and Oracle Database Enterprise 10.2.0.1 (32Bit). The proposed configuration is Red Hat Linux 5 (64Bit) and Oracle Database Enterprise 10.2.0.4 (64Bit).
No plans to change the middle-tier servers:
O/S- Windows 2003
OAS- Oracle Application Server Lite [Forms and Reports Service]- Version 10.1.2.0.2 .
No plans to change the development tools:
O/S- Windows XP SP2
Oracle Forms and Reports - (32Bit) Version 10.1.2.0.2 .
Has anyone encountered any gotchas/compatibility issues we should be aware of ? Do we need to upgrade the middle-tier and Developer Tools at the same time ?
Many thanks in advance for any advice.

Our forms application runs against a databases runnung on lot of platforms, like
HP-UX, AIX, WinServer 2k3, RedHat, Suse,...32 and 64 bit from 9.2.0.8 up to 10.2.0.4...
our development database is a 9.2.0.6 Windows Server 2003 32bit, and I haven't faced any problems on other platforms after moving to them (except the platform specific database bugs).
Only thing I can remember would be, if you make use of the utl_file package on the database - I'm sure you know the dos2unix and unix2dos fileformat problem.
so if you don't plan to change the middle-tier servers you should not run into serious problems (except a recompile of your forms against the new database could be necessary) to my mind. No need for changing middle tier and developer toos.
regards

Oracle database upgrade from 10.2.0.1(32bit) to 10.2.0.4(64bit)

We are planning a Database Server upgrade. The current configuration is Red Hat Linux 4 (32Bit) and Oracle Database Enterprise 10.2.0.1 (32Bit). The proposed configuration is Red Hat Linux 5 (64Bit) and Oracle Database Enterprise 10.2.0.4 (64Bit).
No plans to change the middle-tier servers:
O/S- Windows 2003
OAS- Oracle Application Server Lite [Forms and Reports Service]- Version 10.1.2.0.2 .
No plans to change the development tools:
O/S- Windows XP SP2
Oracle Forms and Reports - (32Bit) Version 10.1.2.0.2 .
Has anyone encountered any gotchas/compatibility issues we should be aware of ?
Many thanks in advance for any advice.

You can check metalink doc
Changing between 32-bit and 64-bit Word Sizes
Doc ID: 62290.1
You'd better patch your 32 bit version to 10.2.0.4 first.

After upgrading from Mac 10.6 to 10.9, firefox creates new windows by an "expanding" animation instead of just appearing. How do I get the old behavior back?

On Mac 10.6.8, when I create a new window by hitting command-N or going to the file menu, or if another page creates a new window, the new window just appears instantaneously. However, after upgrading to Mac 10.9.2, new windows appear by an "expanding" animation, which takes slightly longer than the old "appearing" behavior. (Other apps on my Mac do not exhibit the "expanding" behavior, only firefox.)
Was this behavior intentional? How can I get the old behavior back?
I am using Firefox 28.0.

Hi __trout__,
Go to the mac system preferences and click on Doc. There is a Minimize window using.... select the animation there.
Hope this helps.

If you've "upgraded" from EA6500 to EA6900 please share your results

I have have had EA6500 Version 1 for 15 months. It is getting a bit long in the tooth. (Hardware reset button no longer works, software UI reboot function does not work), unit will stop working once a week or two and require a 30 minute power disconnect to reset.)
Any pros, cons, happiness or regrets?
Thanks.

I have have had EA6500 Version 1 for 15 months. It is getting a bit long in the tooth. (Hardware reset button no longer works, software UI reboot function does not work), unit will stop working once a week or two and require a 30 minute power disconnect to reset.)
Any pros, cons, happiness or regrets?
Thanks.

Since upgrading from FF3 to FF4 I cannot open a new browser window once I already have FireFox4 open. The browser opens, however The webpage itself is Blank(No URL), No tabs, No Bookmarks or toolbars either

Serious Bug-a-Boo :(

Cor-el's suggestion resolved my problem. Apparently the MOZ_NO_REMOTE variable was set to 1 on my system variables. I never made it, and really have no idea how it got there, but deleting this variable and restarting firefox has resolved the issue. Thanks Cor-el!
Marking case: Solved
Solution: Verify the MOZ_NO_REMOTE variable is NOT set to 1. This can be achieved by simply deleting this variable.

Upgrade from 4x2 GB to 2x8 GB Ram results in strange Windows 7 64bit behavior

Similar Messages

Maybe you are looking for