Upgrade from NCS to Prime

Hi.
I am trying to upgrade from NCS ver 1.1.1.24 to Prime 1.2. With the script ncs_patch-1.1.1.24-upgrade-pi_1.2.tar.gz.
And everything runs smooth until Stage 6 of 7., when Updating Database Schema .. is starting
Stage 6 of 7: Updating Database Schema ...
             : This could take long time based on the existing data size.
                 Stage 1 of 5: Pre Migration Schema Upgrade ...
                                       -- complete. Time Taken : 0 hr, 0 min, 52 sec
                 Stage 2 of 5: Schema Upgrade ...
                               : This could take long time based on the existing data size.
Here everything stops. I have waited for 5 hours now is this normal?
Regards
Johan

It looks like you may be able to restore the data as it says here but you may need to simply export the database, install PI and restore.
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/quickstart/guide/cpi_qsg.html#wp56790
Upgrading Cisco Prime Infrastructure
You can upgrade the following Cisco Prime Network Control System products to Cisco Prime Infrastructure 1.2:
•Cisco Prime Network Control System 1.0.0 (NCS 1.0 MR2, 1.0.2.29)
•Cisco Prime Network Control System 1.1.0 (NCS 1.1 FCS, 1.1.0.58)
•Cisco Prime Network Control System 1.1.1 (NCS 1.1 K MR1, 1.1.1.24)
•Cisco Prime Network Control System (WAN) 1.1.0 and Cisco Prime Assurance Manager 1.1.0 (NCS-WAN/PA 1.1 FCS, 1.1.0.1114)
•Cisco Prime Network Control System (WAN) 1.1.1 and Cisco Prime Assurance Manager 1.1.1 (NCS-WAN/PA 1.1.1 MR1 FCS, 1.1.0.1116)
You can upgrade using either of the following methods:
1. Standard—Upgrades your existing system to version 1.2. All existing data is retained and you will be using the same size OVA at the end. The existing product will not be operational until the upgrade is complete. This is the normal option for most users. For details, see Performing a Standard Upgrade.
2. Migration—Allows you to back up the data from your existing system, install Cisco Prime Infrastructure 1.2 as a new system, and restore the existing system's data to the new system. You can then decommission the old system. This option is preferred if you want to migrate to a larger OVA, cannot disturb your production system, or have a large network. For details, see Performing a Migration Upgrade.

Similar Messages

NCS to Prime Infrastructure - Can anyone help?

I have just upgraded from NCS 1.1.1.24 to Cisco Prime Infrastructure 1.2 and I have a couple of questions:
1) How do I get the same look and feel of NCS? In the docs it seemed to suggest there were a couple of views that you could switch between, but I can't find where you do that.
2) I am unable to get to the home/dashboard screen as it says 'You do not have access to the page 'Monitoring Dashboards'. Why is this?
It seems to be linked to the new assurance evaluation licence (60 days). The product says it is licenced and the assurance evaluation licence it says is not being used.
Anyone able to help?

Interesting. When I log in as me via TACACS+ it does not give me an option by my name to select classic view.
However, when I log in as root it does. The TACACS+ users are in the same group as root so surely they should give the same options? I'm using ACS 4.2 for TACACS+.

Migrating from NCS 1.1.2 to Prime 1.2? Possible?

According to this:
http://www.cisco.com/en/US/docs/net_mgmt/prime/infrastructure/1.2/quickstart/guide/cpi_qsg.html#wp73107 it mentions that migrating from NCS 1.1.2 to CPI 1.2 isn't possible.
How can I get around this?

TAC has a patch to upgrade off of 1.1.2.12.
I don't recall but kinda' think it is to get to 1.3.0.20 and not to 1.2.1.12
Basically you take a backup from the 1.1.2.12 server then restore it into a newly build 1.3 server that has had the patch applied.
I've 3 or 4 and it works just fine...

[SOLVED] Upgrade from SLES10 SP3 & OES2 SP2 to SP4/SP3 breaks NCS

Hi folks,
(This post was originally meant to be a rant and a request for help, but
while writing the final paragraph i found the solution. It's still a
rant, but i figured i'd post my solution here in case someone else runs
into the same issue.)
I've just spent several hours banging my head against a broken cluster
node. My system is a 32-bit SLES 10 VM running on VMware ESX 3.5.x.
I upgraded from SLES10 SP3 and OES2 SP2 to the next service packs for
each (using the move-to-oes-sp3 script in yast2 online_update).
Everything went well for the first few update/reboot sequences, then
after the final reboot on SLES10 SP4 & OES2 SP3, cluster services would
not load or join the cluster on restart.
I checked dmesg and found errors about "Loading module compiled for
kernel version 2.6.16.60-0.54.5-vmi" into a previous kernel version, so
i tried downgrading to that kernel version, only to find that it was
older than the one i had just upgraded from (it's the original SLES10
SP3 kernel). So i tried upgrading back to the same kernel which is
running on the other cluster node (2.6.16.60-0.77.1-vmi), but that did
not work any better.
<preaching>
I have to say that i'm not impressed that OES2 SP3 isn't even compiled
against the appropriate kernel, and because of SUSE's kernel RPM
overwrite policy there's no way i can select to boot from a previous
kernel to see if that fixes things. Note to SUSE and other distro
builders: if you're not doing kernel package upgrades like Red Hat or
Ubuntu (so that we can select to boot from the previous kernel from the
boot menu), you're doing it *WRONG*.
</preaching>
I then upgraded again to the latest recommended kernel for SLES10 SP4,
and still no joy. Dmesg shows this error before the rot starts:
allocation failed: out of vmalloc space - use vmalloc=<size> to increase
size.
When searching for this error i stumbled across
http://ubuntuforums.org/showthread.php?t=1613132
which pointed me to
http://www.mythtv.org/wiki/Common_Pr...lloc_too_small
Adding vmalloc=192M to /boot/grub/menu.lst and rebooting solved the
problem for me.
Regards,
Paul

Originally Posted by Paul Gear
On 13/10/11 07:36, magic31 wrote:
> ...
> Not sure if it's related to the issue you've hit, but along the lines
> of what Kevin already mentioned, there are issues that can arries when
> using the VMI kernel (that I've seen) if having multiple flavors of the
> kernel installed along with it (as in having both kernel-vmi as also
> kernel-smp packages installed) ...
> Curious, is that also the case with your setup?
The system in question has kernel-bigsmp and kernel-vmi installed. We
only ever boot from kernel-vmi.
> I've moved to only using the smp kernel on VMware (along with the
> clock=pit boot option to avoid time drift issues, or pmtr I think in
> your case when also running NCS services in the vm).
When we installed the system (on OES2 SP1, i believe) it was a while
ago, and kernel-vmi with clocksource=acpi_pm on the kernel command line
was the only solution we could find to get reliable time. If there are
updated best-practice documents, i'd be happy to hear about them.
However, this is a production cluster and my boss is (rightly) rather
reticent to make major changes.
Paul
the official Vmware paper on time is that IF you're using SLES 10.x 32-bit you will use VMI and NO kernel params (ie, get rid of the clockpit and clocksource=blah).
But if 64-bit then you're okay.
The easiest, IMO (especially with vmware) is to use the miggui (migration utility). That's how I'm converting all my 32-bit servers in vmware to 64-bit. Works quite well.
--Kevin

Upgrade from WCS Base to Plus Licence

Hi,
I purchased the Cisco WCS Base licence WCS-APBASE-50 however need the Plus licence.
Q1. If I purchase WCS-PLUS-UPG-50 will this give me the plus licence?
Q2. Once I purchase WCS-PLUS-UPG-50, how do I upgrade from my Base licence to Plus? Can you do this on the Cisco website?
Thanks,

Here is a link that helps explain the WCS license. WCS is EOS and NCS has taken that over. Prime Infrastructure replaces NCS:) what you should look at is the WCS to Prime Migration license. You will be able to keep you WCS license and have the plus which is built in with NCS. Plus they throw in a 25 license.
http://www.cisco.com/en/US/prod/collateral/wireless/ps5755/ps6301/ps6305/product_data_sheet0900aecd804b4646.html
Sent from Cisco Technical Support iPhone App

CUCM upgrade from 7.1.5 to 10.5.1.10000-7

Is it possible to do the migration from 7.1.5 to 10.5.1.10000-7 which we are doing for jump upgrade from 7.1.5 to 9.1.2.
The reason why I preferred because this jump upgrade we can achieve in isolated network.
In that case can anybody please help to get specific document for that. Kindly have a look on this case.
Regards,
Abi

You can use prime collaboration deployment. PCD will do your upgrade and migration without doing any jump upgrade or intermediate upgrade..
Please refer to the vide below.
https://www.youtube.com/watch?v=JzG4kz1_hL4
All upgrade documentation are available on cisco. Take some time and look at the CUCM 10.5 upgrade document
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/upgrade/10_0_1/CUCM_BK_U4214F9D_00_upgrade-guide-cucm-100.html

Upgrading from cisco LMS 3.0 to a latest version

Hello,
Upgrading from cisco LMS 3.0 to a higher version.
Whatdoes it require?.
What is the current version?
What do we need for upgrading?
Are there specific codes or new need to buy new products?
In case of buying new products, which are the configurations?

H Malik,
You are correct! Latest version is Cisco prime LMS 4.2. There is no direct upgrade from LMS 3.x to LMS 4.x.
The procedure is simple:
Take backup orf old LMS --> Un-install (if same machine)--> Install new LMS --> Restore backup to get old data.
You would need to purchase new license for it.Cisco Prime LMS is now part of the Cisco Prime Infrastructure bundle and is not orderable separately. Cisco Prime Infrastructure bundle follows a size-based incremental licensing model. Device licenses can be combined and added when applied to a single server installation instance. Customers have the option of adding incremental licenses for additional devices as their network grows.Refer to the Cisco Prime Infrastructure Ordering Guide located at http://www.cisco.com/go/primeinfrastructure for the exact part number that matches your requirement and placing the order.
Currently even SmartNet or SAS contracts does not cover major upgrades from LMS 2.x and 3.x; an upgrade part number will need to be purchased to move to Cisco Prime LMS 4.2. These upgrade part numbers reflect a significant discount to protect customers' investment in the Cisco Prime product line.
The data migration process will vary depending on the LMS version from which the data need to be migrated. Migrating data to LMS 4.2:
• LMS 4.2 supports local upgrade or direct inline upgrade only from LMS 4.0.1 and LMS 4.1.
• LMS 4.0 customers are encouraged to install LMS 4.0.1 before doing inline upgrade to LMS 4.2.
• LMS 3.2 and LMS 3.2 Service Pack 1 customers can do a remote upgrade through the LMS backup and restore mechanism.
• LMS 3.1, LMS 3.0, LMS 3.0 December 2007 Update, LMS 2.6, and LMS 2.6 Service Pack 1 customers need to do a remote upgrade to LMS 4.0.1 and then upgrade to LMS 4.2.
-Thanks
Vinod

MSE 3310 unreachable from NCS PI

MSE3310 has been up and running almost a year now and talking to the NCS Prime Infrastructure server with no problem. This morning arrived and checked the wireless via NCS Prime and now it shows the MSE as unreachable. The MSE and the Prime servers are both virtual and on the same network. I am able to ping to and from the MSE and Prime cli's with no problem. I have tried reboots and restarting the MSE services with no luck. Waiting on response from TAC, but was hoping somebody else had experienced this issue. Thanks for any info.

As per Matrix these version are compatiable:
If the MSE is unreachable from NCS make sure the service is running using one or all of these:
[root@MSE /]# /opt/mse/setup/msed status
[root@MSE /]# /opt/mse/setup/msed start
[root@MSE /]# /opt/mse/setup/msed restart
Regards

Upgrading from ZFD4.01 to ZEN 7

Anyone seen any issues????
From 4.01 to ZENWorks 7??
Thanks,
Lee
[email protected]
Operations & Systems Specialist
Enterprise Technology Services & Support
North Carolina State University
14 Peele Hall, Campus Box 7231
Raleigh, NC 27695
919.513.1968
919.831.3538 (fax)
http://www.ncs.ncsu.edu

ZFD4 Agents will work with the ZFD7 backend server for Workstation Import.
The ZFD7 Agents will not work with the ZFD4 Import services.
The supported road is to upgrade the server pieces first and then the
clients.
What is the worst case scenario?
You make me swing by on my lunch hour since I live in Raleigh too :>
Lee Pipkin wrote:
> Great... So the workstation importation pieces will also continue to
> work without issues...?
>
> [email protected] <mailto:[email protected]>
> Operations & Systems Specialist
> Enterprise Technology Services & Support
> North Carolina State University
> 14 Peele Hall, Campus Box 7231
> Raleigh, NC 27695
> 919.513.1968
> 919.831.3538 (fax)
> http://www.ncs.ncsu.edu
>
> >>>
> *From: * Anders Gustafsson<[email protected]>
> *To:* novell.support.zenworks.desktops.4x.app-launcher
> *Date: * 5/5/2006 3:40 AM
> *Subject: * Re: Upgrading from ZFD4.01 to ZEN 7
>
> Lee Pipkin,
> > Anyone seen any issues????
> >
> > From 4.01 to ZENWorks 7??
> > Thanks,
> > Lee
>
> I had one really ugly from 3.x to 7.0. Turned out that the client had a
> WS policy with a scheduled action that installed NALNTSRV from the
> network. In the old ZEN2 days that was the way to install/upgrade
> NALNTSRV on PCs where the users did not have admin rights.
>
> Other than that, no problems. All apps and policies ran just fine once
> we got NALNTSRV sorted out.
>
> - Anders Gustafsson, Engineer, CNE6, ASE
> NSC Volunteer Sysop
> Pedago, The Aaland Islands (N60 E20)
>
> Novell does not monitor these forums officially.
> Enhancement requests for all Novell products may be made at
> http://support.novell.com/enhancement
>
> Using VA 5.51 build 315 on Windows 2000 build 2195
>
>
>
Craig Wilson
Novell Product Support Forum Sysop
Master CNE, MCSE 2003, CCN

I upgraded from 3gs and want to use my old 3gs as an ipod. how can i update my new apple ID on the 3gs as it still shows a previous one that I had?

I recently upgraded from 3Gs to Iphone4 and want to use my old 3Gs as an ipod. how can i update
the user ID on the 3gs to a new one that I have as it is still showing a previous user ID?

Settings>Store...tap the ID shown...sign out...sign back in with the ID you want to use.

Is it really possible to upgrade from a Treo 650 to a Treo 750?

I am not a very happy customer at the moment, but any help would be greatly appreciated. I upgraded from my old Palm Tungsten to a Zire, then to a Cingular Treo 650, combining three devices into one. I have since discovered that the Treo 650 seems to have a faulty transmission mode, as I can rarely be clearly understood by whomever I call. Am on the second (or third, I have lost track) and continue to have the same problem. I get five bars of reception but can't be understood on the other end. A bit of a problem when one is trying to call 911. Am constantly told I am "breaking up". The repair shop says it "Can't duplicate the problem". OK, then I do not want to give up all the info I have stored in the fool thing, and the 750 seems to have a different system, so I thought I would try that. All the stuff I could find seemed to indicate it wouldn't be a problem to upgrade. When the 750 arrived, I tried to install the software from the CD on my Windows XP computer. No dice. Setup encounters an error and closes. Can't even look at the files, because setup tries to run any time I access the CD. From any drive. Gave it to my girlfiend to check on her computer, and the CD seemed to run fine. Other CDs work just fine on my computer. Must be some kind of conflict, but what? Tried calling the AT&T number that suggested they could help with setup, and was first connected to the business center, they routed me to the laptop center, who routed me to the network center, who said they would have to bring in the Palm customer service and connected me to a Mac guy that dumped me back to a menu that took me to someone for whom English is a second language with whom I was trying to communicate over a very poor satellite connection. They made no sense anyway. telling me first that I couldn't have two desktops running (wrong, my girlfriend has my old Zire and the CD worked fine) and then insisting that the serial number on my device had to start with a P, when it clearly does not have any alpha characters in it. Gave up on that route of assistance. Managed to get the new ActiveSync installed from my girlfriends computer over the network. Great. Now let's get my 650 synced with Outlook (which I have not used at home) and see if we can move on. Nope. First I have to update Outlook 2000 from the old Win98 to my current XP. Find the old CD, and square that away. OK, now sync to Outlook. Nope. The sync program gives an error, saying it will only sync with Outlook 98, 2000, and XP(2002). Good grief. I have Outlook 2000, and the software apparently does not recognize it. If the Palm doesn't work, there is no reason for me to keep this phone, and I am very close to returning it and abandoning the Palm entirely when I upgrade to something that works, although I dread re-entering all that information.
Post relates to: Treo 750 (AT&T)
This question was solved.
View Solution.

Thanks for the feedback. Today I installed an Enterprise version of Office 2007 I purchased a while back, but had not yet installed. Microsoft presented a few challenges, but they were quickly resolved. I then downloaded the appropriate conduit from Palm, and synced the 650 with the handheld overwriting the computer. Then used Active Destop to sync the 750. Satisfied I had moved as much info as possible, I called AT&T and had them move the phone number to the new Treo.
Bonus! When the guy at AT&T called me on the new phone to verify it, he said it sounded better than my landline.
Sorry for the streaming paragraph. When it is late I tend to write like I think.
Dave
Post relates to: Treo 750 (AT&T)

I upgraded from iPhone 3GS to iPhone 6. Everything converted fine until I deleted an app in error. When I downloaded it from iTunes, my account is no longer recognized by the app's host servers. Can I go back and re-sync one app from my old phone?

I upgraded from iPhone 3GS to iPhone 6. Everything converted fine. Yesterday I deleted an app in error. When I downloaded the software it from iTunes ( did this many times on the old 3GS), my account is no longer recognized by the app's host servers (Playtika), even though it did after the initial conversion. Can I go back and re-sync just one app from my old phone?

Try deleting what is called the iPod Photo Cache.
http://support.apple.com/kb/TS1314

I have just downloaded the upgrade from Mountain Lion to Yosemite. In the process i am now unable to gain access to iTunes. The app on desktop no longer works and the install is not able to be opened.

I Have downloaded the upgrade from Mountain Lion to Yosemite. In thee process of so doing I have lost access to iTunes.
The app on desktop no longer opens the program and having downloaded and installed as per Apple instructions, can not make a connection.

Hi, drjbuchanan.
Thank you for visiting Apple Support Communities.
Here are some troubleshooting steps that I would recommend going through when experiencing this issue.
iTunes: Troubleshooting issues with third-party iTunes plug-ins
http://support.apple.com/en-us/ts3430
Troubleshooting iTunes installation on Mac OS X
http://support.apple.com/en-us/ht2311
Cheers,
Jason H.

Can't print from IE 8 after upgrading from Vista to Windows 7

My laptop (HP Elitebook 8530w) uses two HP printers: Color LaserJet CP3525x (at work) and Deskjet 6940 (at home). Both printers are accessed across a local network.
I recently upgraded from Vista Enterprise to Windows 7 Enterprise.
Everything still prints fine (from Word, Adobe Reader, Windows Photo Viewer, etc.), except for IE 8! When I try to print a web page from IE, it prints only the page header, and otherwise the sheet is empty. This symptom occurs on both printers. (And of course this worked fine before the upgrade.)
Any ideas? Thanks for any help.
Jeff
This question was solved.
View Solution.

(same poster)
If anyone else is having this problem, I found the solution on another forum (http://social.answers.microsoft.com/Forums/en-US/InternetExplorer/thread/920588e5-ccc4-4e24-83d6-606...).
Specifically, the following steps solved the problem:
1. If it doesn't already exist, create a directory named "Low" in your directory "C:\Users\<your_user_name>\AppData\Local\Temp\".
2. From a command prompt, issue this command: ICACLS C:\Users\<your_user_name>\AppData\Local\Temp\Low /setintegritylevel (OI)(CI)low
Jeff

Fields in read-only mode for BP transaction in upgrade from 4.72 to ECC6.0

Hello,
This is regarding the query for BP transaction in upgrade from 4.72 to ECC 6.0.
While creating BP / Changing BP system is disabling the fields in compnay code & sales area option. There is a SAP not provided 907860; and specified that the proplem is because of the delta customizing.
All the customization settings are as per the note. And the Synchronization Control is also activated. But still the fields are disabled only.
I have checked the field settings also in Cross-Application-Components & Logistic-Genral.
But these are not working for compnay code & sales area data.
please let me know if anyone has faced this type of problem / found any solution on this.
Best Regards,
Shubhada

SAP IMG -> Cross Application Components -> Master Data Synchronization  Synchronization Control -> Synchronization Control -> Activate Synchronization options
This setting allows you to activate synchronization of BP with R/3. Not maintaining the values may result in certain fields being read-only in BP.
Suggested Values:
Source Object: BP | Target Object: CUSTOMER | Active Indicator : X
Source Object: BP | Target Object: VENDOR | Active Indicator : X
Source Object: CUSTOMER | Target Object: BP | Active Indicator : X
Source Object: VENDOR | Target Object: BP | Active Indicator : X
Have you set all of the above settings??
BHARATH

Upgrade from NCS to Prime

Similar Messages

Maybe you are looking for