Upgrade FUS WLC 2504
Hi all,
Eh updated the firmware of my WLC 2504 (FUS) from 1.0.0 to 1.8.0
I can again upgrade from 1.8.0 to 1.9.0 ?
I have read that is recommended once the upgrade of FUS. It is true?
Hi,
yes, you can upgrade the firmware again from 1.8 to 1.9.
it's recommended to upgrade the same firmware version only once.
The FUS upgrade will take approximately about 30 minutes and it will reboot the WLC several times.
it's advised to upgrade once the FUS because the WLC reboots and sometimes they will see that the FUS has not upgraded and upgrade again instead of waiting for 30 to 45 minutes.
However, you can wait for the upgrade of FUS on the WLC to 1.8. once the WLC is stable you can upgrade the FUS again to 1.9.
Hope this helps.
Regards
Salma
Similar Messages
-
Upgrade two WLC 5508 with HA SSO from 7.5.102.0 to 7.6.130.0 combined with FUS 1.9
The running config is:
- Two WLC5508's in HA SSO setup running version 7.5.102.0
- about 130 x 2602i APs
I need to upgrade to 7.6.130.0 using the pre-download feature to minimize the network downtime.
Is it possible to transfer the 7.6 to the controllers and pre-download 7.6 to all APs, then do the FUS 1.9 upgrade and finally start the actual controller upgrade to 7.6.
So the steps would be:
1. Transfer 7.6 image to primary controller (do not reboot!), so still running 7.4 as active image.
2. Start pre-download of 7.6 image to all APs and wait till all APs have the new image (do not know how long it takes for 130 APs).
3. Upgrade both controllers with FUS 1.9 (HA should upgrade both controllers automatically) (takes about 45 minutes?)
4. Make 7.6 image the active/primary image on controllers and APs and reset controllers.
If the steps above will not work, I would need to upgrade FUS 1.9 which means 1 hour downtime and then start the pre-download to all APs. The pre-download can take a long time I heard, so I need to wait and wait before I can start the 7.6 upgrade, which means another 1 hour downtime.
This way I need two maintenance windows instead of one. So would it be possible to combine the pre-download and FUS?
Regards,
Bjorn>Do I need to upgrade the FUS 1.9 before the 7.6 image or can I do the FUS afterwards? If I can do it afterwards, I can do the upgrades in the same maintenance window. This way I can start the pre-download the day before, so I am pretty sure the APs have the image at the time of the maintenance window.
>I cannot find any remarks about the required order of installation (FUS -> image or image -> FUS).
Release Notes for Wireless LAN Controller Field Upgrade Software for Release 1.9.0.0 - p2 :
* This release of the Field Upgrade Software is applicable to CISCO WLC's that are installed with the controller software release 6.0 and later.
So strict reading implies that you have to run 7.6 first.
M. -
WLC 2504 Hangs after upgrading 7.4 firmware
Hi All
We have WLC2504 ( Upgraded to Firmware 7.4) and AP'S are AP 1602
When Wirless Controller trying to Connects AP'S then they are hanging and same is happening for AP'S os we are not able to do configuration.
Pinging continous is breaking for WLC IP Address.
We have upgraded to Latest Firmware 7.4...
I have read that this is Bug in Firmware 7.4....What is the work around??
ThanksHi,
Make sure your WLC 2504 is sync with the NTP Server. -
Greetings,
I am planning on upgrading our redundant 5508 WLC’s from v.7.3.112.0 to v.7.4.110.0 this weekend. One thing I noticed in the release notes of 7.4 is the guideline to update the Field Upgrade Software to v. 1.7.0.0-FUS.
My question is should this FUS be upgraded before or after I upgrade the WLC to 7.4? On the release notes it does state a FPGA error on the does occur on the 5500 series controllers.
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/fus_rn_1_7_0_0.html#wp45499
On a Cisco 5500 Series Controller, it is observed that the controller sporadically reboots (due to a defect CSCtr39523) and displays the following FPGA error message:
fpga: Lost heartbeat from Environment controller, system will reboot in 5 seconds!!!
A crash file is not created to debug or troubleshoot the error.
You can resolve this issue by installing the FUS image. Please see Resolved Caveats for more details.
Thanks,
RobertHonestly, it doesn't really matter the ordr you upgrade in.
Though, I tend to update the FUS before the image.
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
Upgraded my Cisco 2504 from 7.0.220.0 to 7.4.111.0
and upgraded my field upgrade bootloader to 1.0.18.
Now I cannot configure my WLC from the web via IP. Had it configured properly with VLAN, switch and my ASA 5520.
Does this have to do with the ACL's on the WLC.
I've been looking for documentation can't find much in terms of best practices for traffic.
My CPU ACL on wired and wireless are disabled with no ACL for the CPU.
Any suggestions or help would be greatly appreciated.
Thank you
CarlosHello Scott,
I figured it out. I had to do from CLI a reset system command. Once I did that everything came back up. I did not know that field upgrade and firmware upgrade took so long. The instructions say to just to a save and reboot. I found out that you need to do a reset system command again from the CLI.
Appreciate the assistance. -
I've recently purchased a new WLC 2504 , the software version is 7.0.2, i need to upgrade it but i cant download the IOS from cisco .
is there any legal way to do the upgrade? I dont wana do it through the fileshre website.
Any ideas....Hi,
the images can only be downloaded from Cisco official website.
you will have to open a ticket with the TAC and they will be able to publish the image for you.
Thank you -
DEBUG-4-INVALID_MODULE on the WLC 2504 with version 7.6.100????
Hi!!! Please help with the solution.
I have one WLC 2504, 4 Cisco 1141 APs and one AP 1602.
Yesterday, I upgrade the WLC with version 7.5.102 to version 7.6.100.
After the upgrade in Message Logs on the WLC at the same time see the following message:
*RRM-MGR-5_0-GRP: Jan 23 08:44:25.449: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:35:41.189: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:34:17.373: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:25:32.125: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:24:09.309: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:15:23.013: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:14:01.213: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 08:05:13.949: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 08:03:53.149: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:55:04.905: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:53:45.086: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:44:55.813: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:43:37.010: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:34:46.749: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:33:28.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:24:37.669: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:23:20.865: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:14:28.593: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:13:12.789: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 07:04:19.529: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 07:03:04.729: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:54:10.493: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:52:56.689: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:44:01.445: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:42:48.645: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
*sntpReceiveTask: Jan 23 06:35:22.218: #LOG-4-Q_IND: debug.c:2636 Unhandled debug module 5005.[...It occurred 19 times.!]
*RRM-MGR-2_4-GRP: Jan 23 06:33:48.070: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:32:36.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:23:39.030: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:22:28.226: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:13:29.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:12:20.186: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 06:03:20.930: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 06:02:12.130: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:53:11.890: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:52:04.090: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:43:02.838: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:41:56.039: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:32:53.790: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:31:47.986: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:22:44.758: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:21:39.950: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:12:35.718: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:11:31.910: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 05:02:26.670: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 05:01:23.859: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:52:17.606: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:51:15.794: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:42:08.566: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:41:07.750: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:31:59.506: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:30:59.703: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:21:50.450: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:20:51.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:11:41.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:10:43.598: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 04:01:32.326: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 04:00:35.522: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:51:23.258: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:50:27.442: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:41:14.182: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:40:19.378: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:31:05.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:30:11.302: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:20:56.042: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:20:03.242: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:10:46.978: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 03:09:55.178: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 03:00:37.902: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:59:47.102: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:50:28.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:49:39.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:40:19.782: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:39:30.983: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:30:10.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:29:22.942: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:20:01.698: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:19:14.886: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 02:09:52.646: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 02:09:06.842: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:59:43.587: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:58:58.783: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:49:34.546: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:48:50.742: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:39:25.494: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:38:42.687: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:29:16.454: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:28:34.642: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:19:07.402: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:18:26.594: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 01:08:58.362: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 01:08:18.554: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:58:49.322: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:58:10.514: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:48:40.266: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:48:02.467: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:38:31.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:37:54.411: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:28:22.174: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:27:46.374: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:18:13.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:17:38.306: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 23 00:08:04.062: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 23 00:07:30.262: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:57:55.022: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:57:22.222: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:47:45.958: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:47:14.158: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:37:36.906: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:37:06.106: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:27:27.826: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:26:58.026: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:17:18.762: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:16:49.962: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 20 times/sec!.]
*RRM-MGR-2_4-GRP: Jan 22 23:07:09.686: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.[...It occurred 10 times/sec!.]
*RRM-MGR-5_0-GRP: Jan 22 23:06:41.870: #DEBUG-4-INVALID_MODULE: debug.c:2636 Unhandled debug module 5005.
With what may be the problem exists? Any suggestion?Have you upgraded the FUS to 1.8.0.0? What happens if you try to boot from v7.5 do you see the messages and maybe boot back to v7.6?
Here is what the doc mentions about the error
Error Message %DEBUG-4-INVALID_MODULE: Unhandled debug module [dec].
Explanation This module cannot be debugged.
Recommended Action Copy the message exactly as it appears on the console or in the system log. Research and attempt to resolve the issue using the tools and utilities provided at http://www.cisco.com/tac. With some messages, these tools and utilities will supply clarifying information. Search for resolved software issues using the Bug Toolkit at http://tools.cisco.com/Support/BugToolKit/. If you still require assistance, open a case with the Technical Assistance Center via the Internet at http://tools.cisco.com/ServiceRequestTool/create/launch.do, or contact your Cisco technical support representative and provide the representative with the information you have gathered.
http://www.cisco.com/en/US/docs/wireless/controller/message/guide/msgs4.html#wp1000708
Sent from Cisco Technical Support iPhone App -
Dear Friends,
I am using Cisco WLC 2504 current software version is 7.0.220.0 and I want to upgrade it to the latest version which is 8.x.x.x.
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Thank you very much for your help and support.
Thanks
UmarHi
Could you please help and advice the best way of doing it? Also can I upgrade direct to the latest version or do I have to upgrade step by step?
Yes, you can go directly to 8.0.x from 7.0.x code. Refer below link
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/crn80mr1.html#68333
Make sure you refer the release notes for any known issues with this code. Also upgrade FUS to 1.9.0.0 as well. This will take around 30 min downtime as well.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/release/notes/fus_rn_OL-31390-01.html
If you have different AP models, MSE, Prime products, refer this compatibility matrix as reference.
http://www.cisco.com/c/en/us/td/docs/wireless/compatibility/matrix/compatibility-matrix.html
HTH
Rasika
**** Pls rate all useful responses **** -
This might be a really stupid question but I need to ask just so that I get a definitive answer. I have a customer that is using a WLC 2112 and has maxed out the licenses for the WLC. I have suggested for him to purchase a 2504 with 30 or 40 licenses to replace the existing 2112. He doesn't want to purchase 30 to 40 licenses and doesn't want to remove the 2112 from the network environment. He would rather purchase a WLC 2504 with 15 licenses and just add that into the network.
My question is, will there be a problem running a 2504 and a 2112 on the same network? Or can I just make one a primary and one a secondary?That should be fine. Just make sure the WLCs are running the same code version and everything should work fine. This is required for APs failover from one WLC to another. You don't want the APs upgrading or downgrading code versions every time the ap moves from the primary to the secondary WLC.
Sent from Cisco Technical Support iPhone App -
Acs 5.3 and wlc 2504 config with restricted network access
Hello,
i submit you the following issue that i'm actually facing:
i must configure a secured wireless network with access restriction based on SSID. the equipements are : cisco wlc 2504 (soft 7.3) cisco secure acs aplliance 1121 (soft 5.4) .
the users that will connect to the network are regrouped by identity groups, each identity group having it's own SSID. Clearly each group of users must access only one SSID.
i followed the procedure below to configure it:
-- creating user identity groups;
-- creating users and assigning them to the groups;
--- creating authorization profiles for each SSID under policy element/ authorization and permission/network access/authorization profiles and putting the Airespace-Wlan-Id(the SSID number) in the radius tab.
--- assigning the authorization profiles to the identity groups under access policies.
after all these config the users can access the network using there userid/password configured. But the problem is Every user can access every SSID, seems like the restriction is so not very well configured.
i found some documentation on this kind of config but the version of ACS used seems older than the one that i use, so menu are very different.
Please can someone provide with the right steps to follow to achieve this kind of config.
tkx in advanceYes.. you only have to add the end filter like what I posted... as far as the calling station id in the WLC security tab, it doesn't matter because that is not used when using 802.1x. I would also try to not enable everything that you have just to start from the basic and make sure it works first. The WAP Authentication Method might or might not work for you. Uncheck that for now and when you have a successful authentication, look at the monitor log and see what radius attributes are being sent, because those attributes is what you can use to build your policies.
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Client got not connection to wlan over wlc 2504 on 802.11b/g
Hi everybody,
We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
During the debugging found the following:
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
*dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 9) in 10 seconds
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0 cur: 1
*apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates statusCode is 0 and gotExtSuppRatesElement is 1
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
*apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 49) in 1800 seconds
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
*apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
*spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f ..._
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
*dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
*osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 57) in 10 seconds
*dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
*osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
*apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station: (callerId: 45) in 10 seconds
Thanks for any adviceIn some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz. No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz. It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.
Can you check to ensure that the data rates for 802.11b are enabled? Maybe someone disabled data rates from 1 Mbps to 11 Mbps. -
DHCP Error with WLC 2504 and Aironet 2600 setup across subnets
Hey guys
I have just setup a new WLC 2504 controller to manage a WiFi service that will span 6 geographic locations. The local networks at each location are on different subnets (all 192.168.x.x) and are linked up via IPSEC VPN links, and there is Active Directory spanning the sites, with DNS and DHCP servers running at each location.
I tested the WLC at our main office with a single AP, and it worked fine. The AP set itself up, and wireless devices connect with no probs. Great! Yesterday I headed out to one of our remote sites, and connected an AP to their network - and that seemed to work fine too. Within a few minutes I was able to see the WiFi network I'd setup, and my smartphone connected to it straight away (as I'd rpeviously connected at the main office), so I was pretty happy that all was working well.
This morning however I've had notification that wifi performance at the remote site isn't great. I've got someone to check their ip address, and I've found that their IP address and default gateway match the LAN at the main office where the WLC is based - NOT the LAN where the wireless client is. Obvioulsy this is not ideal!
So I guess my question is, what have I done wrong? (I guess I HAVE done something wrong!?). And how can I get wireless clients at remote sites to pick up an IP from the DHCP server at THEIR site?
Any help would be greatly appreciated!
Thanks!Hello Tim,
What mode your APs are in? Local mode? or FlexConnect mode?
If local mode, then all the traffic will be tunnelled to the WLC and they'll be same as if you are connecting from the WLC location.
If you use FlexConnect APs (which is recommended for remote sites) you can configure FlexConnect groups on the WLC and add each location in a specific group. In that group you can decide what VLAN the users should be in.
Check this link for FlexConnect group configuration
http://www.cisco.com/en/US/docs/wireless/controller/7.2/configuration/guide/cg_flexconnect.html#wp1230080
HTH
Amjad
Rating useful replies is more useful than saying "Thank you" -
Best practices for network design on WLC 2504 and 5508
Dear all:
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Maximum amount of AP per port
The scenario when to use all ports in both WLC
Maximum number of clients(users) per port
Bandwidth comsumption of management vs data in order to assign one port for management
I've just found this:
Cisco 5508 controllers have eight Gigabit Ethernet distribution system ports, through which the controller can manage multiple access points. The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller. Cisco 5508 controllers have no restrictions on the number of access points per port. However, Cisco recommends using link aggregation (LAG) or configuring dynamic AP-manager interfaces on each Gigabit Ethernet port to automatically balance the load. If more than 100 access points are connected to the 5500 series controller, make sure that more than one gigabit Ethernet interface is connected to the upstream switch.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/6-0/configuration/guide/Controller60CG/c60mint.html
Thanks for your help.The 5508-12, 5508-25, 5508-50, 5508-100, and 5508-250 models allow a total of 12, 25, 50, 100, or 250 access points to join the controller.
This is an old document. 5508 can now support up to 500 APs if you run firmware 7.X. 2504 can support up to 75 APs if you run firmware 7.4.X.
I'm looking for some recommendations on WLC 2504 and 5508 about the the following:
Best practice and recommendation is to LAG all ports so you will be able to form a link redundancy. If one link goes down, you have other link to push traffic. -
Cisco WLC 2504 webportal for Server 2008 R2 DC LDAP or RADIUS
HI,Friends.
I want to get my mobile or Notebook clients connecting to wireless and use my Domain users ,Cisco WLC 2504 to authenticate via LDAP or RADIUS to our Windows Server 2008 Domain Controllers
question:
one,i can use my domain one Organizational Unit ,such as cn=use01,ou=test,dc=lzh,dc=com. now, noly user01 can logon on web, But how I make all my domain users can use web log it ?
I was using radius authentication or ldap certification to do web authentication ?which is good. ？？？
I specified child ou, ou its users superiors can not be landed onhi ,Scott Fella
Thank you,I am very happy to receive your reply, I finally binding domain user authentication LDAP authentication done successfully. but You say the combination of nps I did not do the radius authentication is successful, I do not know where the problems.
the err:
<Event><Timestamp data_type="4">07/27/2014 18:33:36.845</Timestamp><Computer-Name data_type="1">PDC-CQ</Computer-Name><Event-Source data_type="1">IAS</Event-Source><User-Name data_type="1">11</User-Name><Service-Type data_type="0">1</Service-Type><NAS-IP-Address data_type="3">10.10.10.253</NAS-IP-Address><NAS-Port data_type="0">1</NAS-Port><NAS-Identifier data_type="1">WLC-CNNEWCITY</NAS-Identifier><NAS-Port-Type data_type="0">19</NAS-Port-Type><Vendor-Specific data_type="2">00003763010600000001</Vendor-Specific><Calling-Station-Id data_type="1">10.12.0.11</Calling-Station-Id><Called-Station-Id data_type="1">10.10.10.253</Called-Station-Id><Client-IP-Address data_type="3">10.10.10.253</Client-IP-Address><Client-Vendor data_type="0">0</Client-Vendor><Client-Friendly-Name data_type="1">WLC</Client-Friendly-Name><Proxy-Policy-Name data_type="1">Use Windows authentication for all users</Proxy-Policy-Name><Provider-Type data_type="0">1</Provider-Type><SAM-Account-Name data_type="1">CNNEWCITY\11</SAM-Account-Name><Class data_type="1">311 1 10.10.10.1 07/27/2014 09:41:28 5</Class><Authentication-Type data_type="0">1</Authentication-Type><NP-Policy-Name data_type="1">Connections to other access servers</NP-Policy-Name><Quarantine-Update-Non-Compliant data_type="0">1</Quarantine-Update-Non-Compliant><Fully-Qualifed-User-Name data_type="1">cnnewcity.com/user/test/11</Fully-Qualifed-User-Name><Packet-Type data_type="0">1</Packet-Type><Reason-Code data_type="0">0</Reason-Code></Event>
<Event><Timestamp data_type="4">07/27/2014 18:33:36.845</Timestamp><Computer-Name data_type="1">PDC-CQ</Computer-Name><Event-Source data_type="1">IAS</Event-Source><Class data_type="1">311 1 10.10.10.1 07/27/2014 09:41:28 5</Class><Fully-Qualifed-User-Name data_type="1">cnnewcity.com/user/test/11</Fully-Qualifed-User-Name><Quarantine-Update-Non-Compliant data_type="0">1</Quarantine-Update-Non-Compliant><Client-IP-Address data_type="3">10.10.10.253</Client-IP-Address><Client-Vendor data_type="0">0</Client-Vendor><Client-Friendly-Name data_type="1">WLC</Client-Friendly-Name><Proxy-Policy-Name data_type="1">Use Windows authentication for all users</Proxy-Policy-Name><Provider-Type data_type="0">1</Provider-Type><SAM-Account-Name data_type="1">CNNEWCITY\11</SAM-Account-Name><NP-Policy-Name data_type="1">Connections to other access servers</NP-Policy-Name><Authentication-Type data_type="0">1</Authentication-Type><Packet-Type data_type="0">3</Packet-Type><Reason-Code data_type="0">66</Reason-Code></Event>
then,You gave two figures is that what you mean? what's the meaning it that services-type =login ? -
WLC: 2504
Firmware: 7.6.100
Hello,
I'm getting very confused in how to set up redundancy with WLC 2504. Some sources talk about Client SSO, some about N+1.
But it seems that although I should use Client SSO with firmware 7.6, the WLC 2504 doesn't support it.
When I type config redundancy, I have no choice
>config redundancy ?
unit Configure redundancy unit [primary | secondary]
So I typed "config redundancy unit primary" on my 2504 and "config redundancy unit secondary" on my 2504-HA
And when I issue this command I have very little information
>show redundancy summary
Type of the Unit = Primary
Does someone has guidelines for redundancy with WLC 2504 on firmware 7.6 ?
Thank youHello,
Thank you both for your answers.
Something I didn't understand in the documentation is this.
Is there a replication of configuration between the WLC primary and the HA ? I did read that they should have different network settings (IP addresses) so I understand that there is not a total replication, what about the rest of the configuration ?
The only result I have when I issue a command on the WLC-HA is this
>show redundancy summary
Type of the Unit = Secondary
It doesn't look exactly what I see in the documentation.
Thank you
Maybe you are looking for
-
How to install Windows 2008 as guest
hi I have uploaded ISO in the repostiory 2008R2Entv2.iso 2.3 Import URL: http://internalserver/iso/windows/2008R2Entv2.iso At time of creating Virtual machine . I have selected the ISO . Set the boot order : CDROM,Disk when I run the Virtual
-
hi everyone we have a 2 system landscape.the disk space left on dev is only 28gb. and the production size is 230 gb or something .we want to refresh the production system on the dev server atleast once a month.so is it advisable to upgrade the hardw
-
How/where can I download Indesign 7?
How/where can I download Indesign 7? I have CS6 I need to download 7 to open client's files.
-
How to map adc chanel to an axis
Hello every body. According with "Ni Motion User Manual", it seems possible to use analog feedback. But I can't find how to map an ADC channel to the axis in concern, as appears in comment of the sample program in page 13-5.I also did not know how t
-
Acrobat Reader 8.1.2 document icons are missing.
Hello, In our company, we have deployed Adobe Acrobat Reader 8.1.2 through GPO. We used the Adobe Customization Wizard to generate a MST file (Updates disabled). At first, all seemed to work perfect. A moment later we noticed that the icons of the PD