Upgrade in 7.1.2 : requires a restauration ! Why ?

Hello,
I'm not fluent in english, so I'll do my best to explain the issue ;-)
Yesterday I tried to performed the upgrade of my iPad in 7.1.2 (from 7.1.1). When my iPad restarted I was asked to plug it to my computer (with iTunes icon displayed on the iPad). I never had to do it with the previous upgrade. Furthermore when I plug the iPad, there is a message indicating that a restauration is gonna be performed. How can I avoid this restauration ? Otherwise all my content is going to be lost...
Thank you for further help.
Saks

RECOVERY MODE
1. Turn off iPad
2. Turn on computer and launch iTunes (make sure you have the latest version of iTune)
3. Plug USB cable into computer's USB port
4. Hold Home button down and plug the other end of cable into docking port.
DO NOT RELEASE BUTTON until you see picture of iTunes and plug
5. Release Home button.
ON COMPUTER
6. iTunes has detected iPad in recovery mode. You must restore this iPad before it can be used with iTunes.
7. Select "Restore iPad"...
Note:
1. Data will be lost if you do not have backup
2. You must follow step 1 to step 4 VERY CLOSELY.
3. Repeat the process if necessary.

Similar Messages

  • TS2551 I can't go on my iPhoto it says I have to upgrade it. I click on upgrade and then it says required rebuilding! Why all this?

    I can't go on my iPhoto anymore. It says, that I have to upgrade it. When I click on upgrade it shows iPhoto is unable to open this library. Requires rebuilding. I can't even download my pictures from my camera. Hopefully somebody can help me! Thank you.

    What version of iPhoto?
    The general answer is to backup your iPhoto library. depress the option and command keys and launch iPhoto - rebuild the library from the resulting men
    LN

  • Will upgrading to OS X Maverics require me to reinstall any third party softwar i.e photoshop, after effects etc.

    Will upgrading to OS X Maverics require me to reinstall any third party softwar i.e photoshop, after effects etc.

    Wait for testing.
    Do your own testing. Clone your system first.
    Do a clean install of 10.9 on another drive and then use that with Setup Assistant or Migration Assistant if you want.
    I would not update over the old system - at least not w/o a safety backup net to catch you.
    There are always a couple things that need fixing. And it may be that they won't know until they have the final bits and do their own inhouse testing now that they have the actual release version.

  • HT4972 i get an error flag everytime i try to upgrade my ipad to OS 5.1? why?

    i get an error flag everytime i try to upgrade my ipad to OS 5.1? why?

    See iOS: How to update your iPhone, iPad, or iPod touch
    http://support.apple.com/kb/HT4623
    If you are currently running an iOS lower than 5.0, connect to your computer & click on the "Update your device using iTunes".
    Try this - Disable your firewall and anitvirus software temporarily.  Then download and install the iOS update. After you update to iOS 5.x, the next update can be installed via wifi (i.e., not connected to your computer).
     Cheers, Tom

  • I am using the iPad 3 64 and am an avid photographer . I have been using iPhoto as my editor when I download my pic to my iPad . I have upgraded to IOS 6.  Please tell me why has the delete option has been removed iPhoto?

    I am using the iPad 3 64 and am an avid photographer . I have been using iPhoto as my editor when I download my pic to my iPad . I have upgraded to IOS 6.  Please tell me why has the delete option has been removed iPhoto?

    That was the first thing I check, my X no longer exist, the app still works fine and does everything it did in the past, the the x (delete) option is no longer there.  I have deleted and redownloaded the app and did a complete reset, X still not there as an option.  Is anyone else experiencing this problem? 

  • After upgrading my ipad to ios6 it wont start why?

    after upgrading my ipad to ios6 it wont start why?

    What to Do When Your iPad Won't Turn On
    http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
    iOS: Not responding or does not turn on
    http://support.apple.com/kb/TS3281
    iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
    http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
    iPad: Basic troubleshooting
    http://support.apple.com/kb/TS3274
    iOS: Resolving update and restore alert messages
    http://support.apple.com/kb/TS1275
    iPad: Unable to update or restore
    http://support.apple.com/kb/ht4097
     Cheers, Tom

  • Need to find impact of Vertex O series upgrade on ECC and changes required?

    Hello experts,
    My client is upgrading Vertex series to O from Q.
    As part of Q series, additional fields such street will be used to identify correct tax jurisdiction code in system. 
    Also, zip code used will be 9 digits (zip+4) instead of 5 digits.
    We need to correct existing master data and open transactions in system with new jurisdiction code along with supporting new data in system.
    Below are the questions:
    1. What changes are required in ECC side to support new vertex series in interface etc?
    2. How can we achieve integration of vertex O series with new master and transnational data getting created in system to have right TXJCD value?
    3. What all possible solutions are available to correct master data and transnational data in system with correct TXJCD value?
    Any pointers to experience with Vertex will be rewarded.
    Thank you,
    Gouri. 

    Hi,
    > 1. is there any dependency for the remaining systems in the landscape (SRM 5.0 SPS15, NW 7.0 SPS18, PI 7.1 SPS8, >SOLMAN EHP01 SPS22)?
    As such there is no dependency between component you specified but SAP always says to be on latest patches. As far as solution manager is concerned you should have minimum support pack level Solman 7.0 SP17 but anyway you are more than that.
    > 2. we are using AIX Version 5.3 and "DB2 v9.5.0.2", does it support ECC 6.0 EHP04 or do I need to upgrade?..
    It is fine with your upgrade.
    > 3. Java version for NW 7.0 is as follows:
    > java version "1.4.2"
    > Java(TM) 2 Runtime Environment, Standard Edition (build 1.4.2)
    > Classic VM (build 1.4.2, J2RE 1.4.2 IBM AIX 5L for PowerPC (64 bit JVM) build caix64142-20080122 (SR10) (JIT enabled: jitc))
    > Does it support my requirement or any upgrade is required?
    >
    Java version is also fine.
    Thanks
    Sunny

  • Upgrade 4.6C-- ECC6 , Hardware requirements

    Hi  Experts,
    We are currently in 4.6C R/3 with 46D kernel ( Oracle 9.2DB and HP-UX B.11.00)
    We have two servers  ( DB instance 12X750MHz 20GB, Application 10X875MHz 20GB) .Machine is rp8400 , disk - 460GB
    when we go for ECC6 , I understand we should go for upgraded hardware first. Cananybody please give a high level idea of the new hardware requirements.
    Thanks in advance
    Arun

    Its it an upgrade to ECC or it will be a fresh installation.
    Check with your hardware vendor he will be able to provide you the details.
    There are many factors for H/w sizing. You can use the quick sizer tool for details.
    Sit with your functional consultant and use the quick sizer tool for a rough estimate
    Check the installation / upgarde guide for minimum hardwrae specifications for ECC 6.0
    Thanks

  • Want to migrate my iMac g5 w/sys 10.3.9 to new mac book pro, how do i upgrade to the minimum system required?

    I want to migrate my iMac g5 from 2004 with system 10.3.9 to a new macbook pro. How do i upgrade to the minimum system (10.4.11 or 10.5.6 or later) required? Thank you.

    You need to realize that if you buy a new Mac now with
    Lion installed, all your PPC apps will not work.
    You may just want to build your new system form scratch
    and manually move the data you need.  Migrating will bring almost
    everything over and, since 2004, there may be a lot you just don't
    want or need.
    Also, installing those programs that you own that are
    universal installers (contain Intel code) will
    insure everything is put in the right place.
    Having a fresh clean system to start out with is not
    a bad idea.  It's more work but in the long run will
    help to alleviate problems.

  • Does upgrading from 2003 to 2010 require a verify database on reports?

    Hello,
    I am working on upgrading an application from VS 2003 .Net 1.1 to VS 2010 .Net 4.0. I have installed the SAP Crystal Reports for Visual Studio 2010. After doing this I found that reports that had worked with .net 1.1 now do not work. When in the code, after loading a report and the printing
    such as
    Dim crDoc As New ReportDocument
    crDoc.Load(strTemplatePath & strFile)
    SetConnectionInfo(crCon, crDoc)
    SetParameters(crDoc, parameters)
    crDoc.PrintOptions.PrinterName = Me.strPrinter
    crDoc.PrintToPrinter(1, False, 0, 0)
    When the document goes to PrintToPrinter i receive an error message like 'Error in file blahblah.rpt: The table could not be found'. If I do a verify database on the report  in question it will print correctly. However there are quite a few reports. Is a verify database expected after upgrading to .Net 4.0? Thanks for you help and have a great day!

    Hello,
    Typically when moving to one version change it's not required but in your case CR 9 was the version in 2003 and lots of DB changes to both CR and the Db Client engines.
    So yes in this case you should Verify the database. You can do this once using a test, save an update flag in the SummaryInfo page, same as in the Designer when you click on File SummaryInfo. You can read/write to the comments and then test if a SaveAs or Export to RPT format was done. This will update the RPT format and connection info. So if it's updated then simply setting the user name and password is all that is required or even less if you have enabled Trusted Authentication.
    Also, now that you have updated to CR for VS 2010 I highly recommend you start using RAS rather than the CR Basic which uses the Engine. You can still use both but the Engine and it's functions are not updated. If any updates or features added it will always be in RAS.
    Also highly recommended is to use the PrintOutputController to print your reports rather than using PrintToPrinter....
    Don

  • After 10.1.2 upgrade, Create/Modify User/Group requires re-authentication

    I have 3 systems - 2 were 9.x (AS10g R1) upgraded to 10.x (AS10g R2), 1 was installed as 10.x. On the two upgraded systems, after a Portal user logs in (with administration privileges), navigates to the "Administration" tab and clicks either the "Create New User", "Modify User", "Create New Group" or "Modify Group" links, they are prompted for a username and password again. On the system installed with 10.x, this does not happen. Submitted iTar was unresolved. Has anyone seen this before?
    Thanks in advance.

    Please read this whole message before doing anything.
    This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
    The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

  • Upgrading to Lion and memory requirements.

    hi - I have Mac OS X Snow Leopard10.6.8.  I went to download Lion and it said I didn't have enough memory (needed 2GB).  When I looked on my system - it shows I only have 1GB and change left.  Can I not download Lion? Is this Apple's way of making me purchase a new computer?  My iMac isn't that old - almost four years.  I just got the new iphone and I have icloud on that and my iPad.  now, my iphone is not synching my calendar and contacts with my iMac - the store said i needed Lion on my desktop.  I do have a mobile me account - but don't really use it except for the synching of my calendar and contacts - now that's not working.  I have a separate apple ID for itunes, apps, etc.  I would like to get rid of mobile me and have one apple ID.  I'm so confused with all of these changes.  Everything is not meshing as they make it seem:(  I hope someone can help me?  Thanks

    No.  All iMacs that can run Snow Leopard can be upgraded to 2 GB of RAM.  For instructrions on upgrading your RAM, check http://www.apple.com/support/imac/ Just make sure to properly identify which iMac model you have:
    http://support.apple.com/kb/HT1758
    And buy the RAM from a reputable vendor that has a lifetime warranty that specs the RAM for your model*:
    http://www.macmaps.com/badram.html

  • *** WARNING *** Upgrade to 5.0 may require isolating LWAPs from the WLC

    Before you run into the problem that we ran into when one of our larger customers upgraded from 4.2 to 5.0 and the result was that the controllers got caught in a loop during the upgrade and took the entire WLAN down.
    Please be advised that Cisco recommends that you ISOLATE all lightweight access points from their controller during the upgrade of the controller from 4.2 to 5.0.
    In part, this is due to a bug in 4.2.xx that starts upgrading the LWAP software images before the controller finishes updating/rebooting. This can cause interruption to the LWAPs as they upgrade their software from the controller when it reboots.
    I have also heard of some situations where the LWAPs get corrupted to such a degree where you may have to out and physically access/reset the LWAPs that were interrupted during the upgrade process. I believe the worst-possible-case for this would be limited to no more than 10 LWAPs per controller
    that can upgrade at a time)
    In our case, the result was that the upgrade process hung up - with some LWAPs stuck, and all other LWAPs unable to pass traffic through the upgraded (ver 5.0) controller because they were at the previous revision (4.2).
    In our case, this resulted in a system-twide WLAN outage.
    As part of the call into Cisco TAC, the engineer said, in effect, 'why didn't you ignore the release notes instructions and isolate your controller from the LWAPs during the upgrade?'.
    Our response was, we would have done so if it had been in the release notes (which it is not). So, after much cajoling by us, TAC finally agreed that it might be a good idea to include this additional step in the release notes.
    Please reference the bug which requests an update to the 5.0 release note installation instructions: CSCso02420
    TAC is aware of this problem and it is my understanding that there is discussion at Cisco regarding a maintenance release for 4.2 (since 4.2 is where the problem actually lies). The maintenance release would be applied to 4.2 controllers PRIOR to upgrading them to 5.0.
    In the meantime, if you are still anxious to upgrade to 5.0, one workaround is to isolate the LWAPs from the controller either by:
    1) Physically disconnecting the controller from the network during the upgrade and reconnecting it after its upgrade/reboot is complete.
    or
    2) Temporarily disabling the VLAN that carries the LWAP traffic to/from the LWAPs/Controller and re-enabling the VLAN after the upgrade/reboot of the controller.
    I hope that this is helpful for anyone out there who is about to upgrade to 5.0.
    I hope your upgrade goes smoother than our customer's did.
    - John
    (Please remember to rate helpful posts)

    FYI - I noticed these messages in the message log on a 4.0.179.11 controller, sourced from 4.2 controllers.
    Fri Mar 14 17:14:36 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:36 2008 [ERROR] mm_listen.c 4157: Mobility packet IP-message IP mismatch: pkt: 172.20.48.68 msg: 215.42.227.2
    Fri Mar 14 17:14:36 2008Fri Mar 14 17:14:33 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:33 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:32 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:32 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:32 2008 [ERROR] mm_listen.c 4157: Mobility packet IP-message IP mismatch: pkt: 172.20.48.6 msg: 215.42.227.24
    Fri Mar 14 17:14:32 2008Fri Mar 14 17:14:29 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:29 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:26 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:26 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:23 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:23 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:22 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:22 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:19 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:19 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:16 2008 [ERROR] ethoip.c 305: ethoipSocketTask: ethoipRecvPkt returned error
    Fri Mar 14 17:14:16 2008 [ERROR] ethoip.c 106: Eth-over-IP pkt too short; pkt size=82, expected min=66
    Fri Mar 14 17:14:13 2008 [ERROR] mm_listen.c 4157: Mobility packet IP-message IP mismatch: pkt: 172.20.48.4 msg: 215.42.227.24

  • Stuck at 10.4 - Cannot upgrade - Volume does not meet requirements.

    I just installed a new hard drive in my 12" Powerbook G4. I did a clean install of Tiger - 10.4 - without any problems. I formatted the drive Mac OS Extended (Journaled) with one partition.
    After booting and going through the setup process, I looked for updates. There were some iTunes, Java and DVD player updates, but that was it. I applied those and restarted. I ran software update again, but there were no OS updates. I downloaded the OS 10.4.10 PPC combo updater and ran it, but the hard drive has a red exclamation point with the warning that the update cannot be installed because the volume does not meet the requirements.
    I then downloaded the 10.4.1 updater, and I got the same error.
    I then zapped the PRAM and rebooted, but I got the same error. I then repaired permissions and rebooted and got the same error.
    Then, I again did a clean erase and install of 10.4 from the original Tiger disc, but I'm again getting the same error.
    I'd like to get this machine updated to 10.4.10 as soon as possible, but I'm not having any luck.
    Any other suggestions?

    I just installed a new hard drive in my 12" Powerbook G4. I did a clean install of Tiger - 10.4 - without any problems. I formatted the drive Mac OS Extended (Journaled) with one partition.
    This is functionaly the same as an erase and install as my user tip explains:
    http://discussions.apple.com/thread.jspa?messageID=607614
    Mac OS X doesn't offer a "clean install" per se.
    How old is your Powerbook G4? If it was released prior to April 25 2005, you need to use the black retail 10.4.0 Installer disk to install Tiger which looks like . If it was released afterwards you need the same disk labeled 10.4.6, or the disk which came with the Powerbook. If you are using another vintage Mac model's installer disk, that won't work, and will yield this error. If you imported data from an Intel Mac via the Migration Assistant you could also have this error. If your hard disk is over 85% full, you may also have this problem. If permissions have not been repaired, or the directory is damaged this error could also happen. Is your data backed up? Do any of these possibly apply to you?

  • I am using iPhone 5 in Cambodia, I bough this phone second hand from s.o. When I upgrade to iOS 7, it require me to activate this phone with iCould account. But this iCloud account is belong to the first owner and I am is a second owner. Please help me

    My iPhone 5 require to activate by iCloud account, but I bough this iPhone 5 from s.o and I has no that account. So how can I do to recover my iPhone 5?

    Sorry... you cannot... Can you return it for a Refund.? Because...
    The Apple ID and Password that was Originally used to Activate the iDevice is required.
    If you cannot get this information from the previous owner
    Removing a device from a previous owner’s account
    You will not be able to re-activate it.

Maybe you are looking for