Upgrade my old Tandberg MXP 6000, 3000 and 880

I have to 3 Question
1. I am trying to download upgrade to F9.1 or higher for Tandberg MXP 6000, 3000 and 880
2. Is there any instruction on how to install them
3. and do I need a license Key for it.

You can download it from either of the two locations:
Cisco website
TANDBERG FTP
Also, if you're upgrading from F8 or below, you can contact TAC and point them to this security advisory, with it, you can get the MXP F9.3.1 software for free without the need of a service contract.
You will need a release key if you're going from one major version to another, ex: F8 or below to F9.  Minor versions don't require a release key, ex: F9.1 to F9.3.1.
Instructions on how to upgrade an MXP codec can be found in the Admin Guide, on pg 141.

Similar Messages

  • Tandberg MXP 6000 Portable and VLAN assignment

    Hello,
    We have a couple of Tandberg MXP 6000 portable VC units that we'd like to be a bit more "portable".  At present any time someone wants to move the unit to a new location we have to configure a switch port as an access port for our voice/video vlan, obviously because these VC devices do not support CDP for vlan assignment.  I can see no way in the settings to tell the unit which vlan to use.
    Ideally I'd like the users to be able to plug these into any wall jack and have the unit assigned the correct vlan, for QoS purposes.  We've tried having the unit move around with its own 8-port switch but anywhere these get plugged in, spanning tree blocks the port because portfast is enabled on the majority of our generic data jacks.
    Is LLDP a possibility here?  If so how would I go about configuring this?
    Does anyone have any other solutions?

    You can download it from either of the two locations:
    Cisco website
    TANDBERG FTP
    Also, if you're upgrading from F8 or below, you can contact TAC and point them to this security advisory, with it, you can get the MXP F9.3.1 software for free without the need of a service contract.
    You will need a release key if you're going from one major version to another, ex: F8 or below to F9.  Minor versions don't require a release key, ex: F9.1 to F9.3.1.
    Instructions on how to upgrade an MXP codec can be found in the Admin Guide, on pg 141.

  • Tandberg mxp 6000 camera auto focus

    Hello sir,
                  I saw the issue form Tandberg mxp 6000 camera auto focus.
    when I zoom the camera it focus image blurring after zoom out fully its blurring few minutes and its clear but its not focus correctly. I change camera and check the different location its same. conference room room size is approximately 15 to 18 feet length. pls tell any other option to solve the issue. I also do software upgrade and downgrade also.

    Does it matter? NO REGISTER packets arrived to server, i was sniffing traffic.
    Problem solved just after i entered valid DNS server address in IP parameters. Why would it need DNS if i'm using direct IP addresses...
    Anyways, my SIP server (Asterisk) does not support duo-video and because there is two video streams in SDP message, it choses wrong RTP port and streams other's side video to presentation channel.

  • I upgraded my old mac to snow lepord and now when i try to play music in my i tunes it says "file can not be located" but it still lists all of my music

    I upgraded my old mac to snow lepord and now when i try to play music in my i tunes it says "file can not be located" but it still lists all of my music

    Use Spotlight Search (the magnifying glass on the top right-hand corner of your menu bar) to locate your music files. Then point iTunes to those files.

  • Register TANDBERG MXP 6000 over SIP

    Hi, i have MXP6000 with 9.1 software. Cant make it register with SIP. No single packet comes from MXP to server.
    Has anyone been able to make it register with SIP server?
    Config is quite simple:
    xConfiguration Conference SIP URI: "[email protected]"
    *c xConfiguration SIP Mode: On
    *c xConfiguration SIP Server Discovery: Manual
    *c xConfiguration SIP Server Address: "10.96.37.10"
    *c xConfiguration SIP Server Type: Auto
    *c xConfiguration SIP Authentication UserName: "6000"
    *c xConfiguration SIP Transport Default: UDP
    *c xConfiguration SIP TLS Verify: Off
    *c xConfiguration SIP ICE Mode: Off
    *c xConfiguration SIP MNS Mode: Off
    *c xConfiguration SIP ForceTurn Mode: Off
    *c xConfiguration SIP DefaultCandidate Type: Host
    *c xConfiguration SIP Legacy Mask: ""
    *c xConfiguration SIP ReplyTo URI: ""

    Does it matter? NO REGISTER packets arrived to server, i was sniffing traffic.
    Problem solved just after i entered valid DNS server address in IP parameters. Why would it need DNS if i'm using direct IP addresses...
    Anyways, my SIP server (Asterisk) does not support duo-video and because there is two video streams in SDP message, it choses wrong RTP port and streams other's side video to presentation channel.

  • CUCM 7.1 sip to Tandberg MXP 3000

    Hi All,
    Does anybody have any pointers on getting a CUCM 7.1 cluster talking to a Tandberg MXP 3000 via SIP.
    We have separate ISDN Bri for our Tandberg and want to get rid of them and pass voice only calls via call manager and a 2821 gateway router with 2 PRI's.
    Any pointers would be real helpful.

    yes you can
    just setup a SIP trunk or H323 ICT trunk with the CUCM
    and make sure you have the right setup in VCS and CUCM interns of SIP uri, or H323 ID
    and in CUCM make sure you setup the right, regions/codec, locations, and CSS
    also by using search rules and transformations in VCS you can control which call to send to CUCM ( for example on PSTN calls )
    you can test it before you remove the existing PSTN lines ( recommended )
    good luck

  • I did an upgrade from 4.0 to the new 6.0 about 5 months ago. After the upgrade installed it said reboot system to apply upgrade. Now it wont open and keeps telling me that the older version needs to shut down the computer and upgrade the old version.

    Look at original question. When I did the download to the new 6.0 it said everything was fine. Then when I tried to use the firefox again it said an older version needed to shut down my computer so that it could upgrade the old version. It wont let me do anything and all it says is shut down computer so old version can upgrade. It wont let me open the program or remove it or anything. PLease help me with this. I really like Firefox but this has been going on for 5 months now and I still dont get answers from you. How do I fix this???

    Look at original question. When I did the download to the new 6.0 it said everything was fine. Then when I tried to use the firefox again it said an older version needed to shut down my computer so that it could upgrade the old version. It wont let me do anything and all it says is shut down computer so old version can upgrade. It wont let me open the program or remove it or anything. PLease help me with this. I really like Firefox but this has been going on for 5 months now and I still dont get answers from you. How do I fix this???

  • I've just upgraded to latest version of Firefox 4 and my Mac is only OSX.10.4.11 and it won't open. How do I downgrade and get old Firefox back. Don't want to lose all my bookmarks. Why was I able to install in the first place. Very frustrated!!

    've just upgraded to latest version of Firefox 4 and my Mac is only OSX.10.4.11 and now it won't open. How do I downgrade and get old Firefox back. Don't want to lose all my bookmarks. Why was I able to install in the first place. Very frustrated!!

    You can get the latest version of Firefox 3.6 from http://www.mozilla.com/en-US/firefox/all-older.html
    You can trash Firefox 4.0 then re-install Firefox 3.6, it will use your existing bookmarks, passwords etc
    Mozilla are working to prevent Mac users with non-compatible systems from getting the notification about Firefox 4, and also not displaying the "Download Firefox 4" button on http://www.mozilla.com

  • I have a rather old iMac 20" (mid 2007) and I want to upgrade the Hard drive. How do I change it? How do I transfer all my applications? May I just copy the old hd into the new one? Thanks.

    I have a rather old iMac 20" (mid 2007) and I want to upgrade the Hard drive. How do I change it? How do I transfer all my applications? May I just copy the old hd into the new one? Thanks.

    There are many online tutorials on how to change out the HD on a mid 2007 iMac. One of the originals is from 2007 and is Upgrade your iMac 20" or iMac 24" aluminum (mid 2007) to 1TB Hard Drive and 4 GB RAM - DIY Guide. As far as migrating your system Apple helps out with that in Setup Assistant which automatically starts when you turn on a new Mac for the first time. After you have installed the new HD you will have to format the new HD to Mac OS Extended (Journaled) and then you will have to install OS X. The first time you turn it on Setup Assistant will start. Follow the directions and you will be fine. In order to restore your information you will need to backup what is on the current internal HD first. I'd recommend using Time Machine (Assuming you are using Leopard or later) AND also creating a bootable clone using either SuperDuper or Carbon Copy Cloner.
    Please complete your profile so at the very least we know what version of OS X your machine has installed.

  • I recently upgraded my old powerbook to an iMac.  I've dumped the files of my backup drive into the new iMac. Is there a way to have access to all the files (new and old computers) when logged on as the same user vs. logging in and out to access each?

    I am new to posting to this support community but have often referred to it for answers.  So thank you all who've contributed; you've been a great help!
    I recently upgraded my old powerbook to an iMac.  I've dumped the files of my backup drive into the new iMac. Is there a way to have access to/merge all the files (new and old computers) together so when I'm logged in can access all the files.
    Thanks!
    M

    Sure-glad to help you. You will not lose any data by changing synching to MacBook Pro from imac. You have set up Time Machine, right? that's how you'd do your backup, so I was told, and how I do my backup on my mac.  You should be able to set a password for it. Save it.  Your stuff should be saved there. So if you want to make your MacBook Pro your primary computer,  I suppose,  back up your stuff with Time machine, turn off Time machine on the iMac, turn it on on the new MacBook Pro, select the hard drive in your Time Capsule, enter your password, and do a backup from there. It might work, and it might take a while, but it should go. As for clogging the hard drive, I can't say. Depends how much stuff you have, and the hard drive's capacity.  As for moving syncing from your iMac to your macbook pro, should be the same. Your phone uses iTunes to sync and so that data should be in the cloud. You can move your iTunes Library to your new Macbook pro
    you should be able to sync your phone on your new MacBook Pro. Don't know if you can move the older backups yet-maybe try someone else, anyways,
    This handy article from Apple explains how
    How to move your iTunes library to a new computer - Apple Support''
    don't forget to de-authorize your iMac if you don't want to play purchased stuff there
    and re-authorize your new macBook Pro
    time machine is an application, and should be found in the Applications folder. it is built in to OS X, so there is nothing else to buy. double click on it, get it going, choose the Hard drive in your Time capsule/Airport as your backup Time Machine  and go for it.  You should see a circle with an arrow on the top right hand of your screen (the Desktop), next to the bluetooth icon, and just after the wifi and eject key (looks sorta like a clock face). This will do automatic backups  of your stuff.

  • I have a Olympus C-3000 and it won't read in the new iphoto.  It reads in my old version on my older computer.  Is there a driver I need or something else?

    I have a Olympus C-3000 and it won't read in the new iphoto.  It reads in my old version on my older computer.  Is there a driver I need or something else?

    Yes, different computers, different OS's, as stated, does not work on any machine except PPC.
    Nothing in console logs.  Does not show up in USB under system profiler.
    Level 1 tech support.  "May be this" or "may be that", but all a waste of time unless someone has the actual camera and can independently verify my results.
    If it were just a matter of it happening on one machine that would be one thing.  The fact that it only does not work on Intel based machines (and thus Snow Leopard and Lion) it is a pretty good indicator that something is missing in the OS.

  • I upgraded my three year old ipad to IOS 8 and it's working very slow and irregular, can I go back to the old settings?o

    I recently upgraded my three year old ipad to IOS 8 and it's working very slow and sometimes freezes. Can I go back to the old system?

    No, downgrading the iOS version is not supported by Apple.
    You could see if any of the following improve things :
    - closing apps via the iPad's taskbar : iOS: Force an app to close.
    - if having problems with Safari, clearing its history and data : Settings > Safari
    - soft-reset : press and hold both the sleep and home buttons for about 10 to 15 seconds (ignore the red slider), after which the Apple logo should appear - you won't lose any content, it's the iPad equivalent of a reboot.
    - backing up (and copying any purchases over to your computer's iTunes library via File > Devices > Transfer Purchases) and restoring
    - adjusting settings e.g. turning 'reduce motion' on (Settings > General > Accessibility), turning off 'background app refresh (Settings > General), turn off multitasking gestures (Settings > General)
    - resetting back to factory defaults (after copying off purchases and any documents, photos etc that you want to keep) and then resyncing it back

  • I have I pad 2, and I recently reset my password. And now I am not able to upgrade my old apps. Usually it will not ask apple password, but now it's asking password and when I type the password ir says the password is wrong. What would be the problem?

    I have I pad 2, and I recently reset my password. And now I am not able to upgrade my old apps. Usually it will not ask apple password, but now it's asking password and when I type the password ir says the password is wrong. What would be the problem?

    If the old ID is yours, and if your current ID was created by editing the details of this old ID (rather than being an entirely new ID), go to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID.  Click edit next to the primary email account, change it back to your old email address and save the change.  Then edit the name of the account to change it back to your old email address.  You can now use your current password to turn off Find My iDevice, even though it prompts you for the password for your old account ID. Then save any photo stream photos that you wish to keep to your camera roll.  When finished go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud).  Next, go back to https://appleid.apple.com and change your primary email address and iCloud ID name back to the way it was.  Now you can go to Settings>iCloud and sign in with your current iCloud ID and password.

  • I want to upgrade my old airport express to the new express. Can I just switch out the old for the new or must I delete the old network first and start from scratch with the new express?

    I want to upgrade my old airport express to the new express. Can I just switch out the old for the new or must I delete the old network first and start from scratch with the new express?

    It is not necessary to delete your old wireless networks first, but doing so may eliminate confusion. If you wish to do that, open System Preferences > Network, and select Wi-Fi from the left column. Click the Advanced... button, then select your old wireless networks and delete them with the "–" (minus) button. Make sure the "Remember networks this computer has joined" remains checked.
    OK then Apply.
    This prevents your Mac from searching for your previous network which will no longer exist.
    A new Express creates an open wireless network that you must select before you can configure it. It appears in your Wi-Fi menu like this:
    Select it. AirPort Utility will load and walk you through its configuration.
    Edit: If you are really using OS X 10.5.1 as shown in your profile, the above screenshot is not applicable. Instead, select the network called "Apple network nnnnnn" and then launch AirPort Utility.

  • CS2 on old Mac, bought new Mac and CS5 upgrade, new Mac will not recognize old serial number to acti

    CS2 on old Mac, bought new Mac and CS5 upgrade, new Mac will not recognize old serial number to activate upgrade

    Jakida for issues with serial numbers we will need you to contact our support team.  For the best assistance, I recommend our chat support at http://adobe.ly/yxj0t6.  Our chat representatives can provide a personalized experience to resolve the issue you have described.

Maybe you are looking for