Upgrade Prime NCS v1.2 to Prime Infrastructure 1.4

Hello!!!!!
I need your help
How do you do for upgrade Cisco Prime Network Control System version 1.2 to Cisco Prime Infrastructure version 1.4
I go to cisco.com->Downloads Home-> Products->Wireless->Wireless LAN Management-> Unified Wireless LAN Management->
Cisco Prime Infrastructure-> Cisco Prime Infrastructure 1.4->Prime Infrastructure Software-1.4.0
I download PI-upgrade-bundle-1.4.0.45.tar.gz
is  similar to upgrade to switch o router???

What I would do, is export the Maps.  Then I would shut down the current VM, load the 1.4 OVA as a new install.  Once you have the WLC added, you can then import the Maps.
This method will keep the DB from getting corrupted, and maintain your Maps and AP placements. 
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered

Similar Messages

  • Upgrade Prime Infrastructure v1.2.1.012 to v1.3.0.20

    Hi,
    is there any patch for upgrade from v1.2.1.012 to v1.3.0.20?
    Or I can install upgrade directly?
    St.

    But there is:
    IMPORTANT: You MUST patch your existing system prior to using this upgrade installer. See appropriate patches under Prime Infrastructure Patches.
    And in the table:
    f your existing system is...
    Download this point patch file
    Cisco Prime Network Control System 1.1.0 (1.1.0.58)
    ncs_patch-1.1.0.58-upgrade-12.tar.gz
    Cisco Prime Network Control System 1.1.1 (1.1.1.24)
    ncs_patch-1.1.1.24-upgrade-12.tar.gz
    Prime Infrastructure 1.2 (PI 1.2.0.103)
    pi_1.2.1.12_update.tar.gz
    Last row doen't match current version (1.2.1.012)
    St.

  • Upgrade Prime Infrastructure v1.2

    Hello Support Community,
    I want to upgarde my Prime Infrastructure which is in version 1.2 to a newer version (1.4 or 2.0) to be compatible with the version 7.5.102.0 of the contoller WLC.
    Which version should I choose for the Prime infrastructure v1.4 or 2.0?
    is there a cost for this upgrade?
    I found some documentation on this topic but I need your help to clarify this point.
    Thanks in advance for your response.
    Best regards

    Yes.... PI 1.2 was not great and upgrading has caused many issues.... you can search the forum on that.  I always stand up a new VM and just export and import the floor maps and rehost the license.  The matrix shows you what WLC code that PI supports and what AP's PI supports.  You need to understand that as you might choose either PI 1.4.1 or PI 2.0.  PI 2.0 was built around converged access so since you have a Unified WLC, you should go with PI 1.4 and patch that to PI 1.4.1.
    Thanks,
    Scott
    *****Help out other by using the rating system and marking answered questions as "Answered"*****

  • Upgrading prime infrastructure 2.1.0.0.78 - 2.1 cannot do app backup

    Hi All
    Trying to do an upgrade prime 2.1.0.0.78  to prime 2.2.
    I have saved an app backup off the exisitng prime 2.1.0.0.78
    However when i try to restore to the new prime infra 2.2 
    with the backup from the 2.1.0.0.78 it fails with a database error
    My technical support say i should change the new vm server
    to match ip addresses etc with the old one but that cant be right
    as this is the official blurb for the types of backups ...
    Application backups: These contain all Prime Infrastructure application data, but do not include host-specific settings, such as the server hostname and IP address. Application backups are intended for use when Prime Infrastructure is running as an OVA on customer-supplied hardware, as restoring from the backup may need to be to a server with completely different host settings.
    Appliance backups: These contain all application data and host-specific settings, including the hostname, IP address, subnet mask, and default gateway. Appliance backups are intended for use when Prime Infrastructure is running on a Cisco-supplied appliance, and restoration is most likely to be to a server with the same host settings.  
    I am obviously using the application backups
    Kind regards
    Steve

    Here you go ....
    Initiating restore.  Please wait...
      Restore Started at 02/02/15 17:29:54
      Stage 1 of 9: Transferring backup file ... 
      -- completed at 02/02/15 17:30:59
      Stage 2 of 9: Decrypting backup file ...
      -- completed at  02/02/15 17:34:00
      Stage 3 of 9: Unpacking backup file ...
      -- completed at  02/02/15 17:34:01
    Stopping strongSwan IPsec failed: starter is not running
      Stage 4 of 9: Decompressing backup ...
      -- completed at  02/02/15 17:34:31
      Stage 5 of 9: Restoring Support Files ...
      -- completed at  02/02/15 17:34:32
      Stage 6 of 9: Restoring Database Files ...
      -- completed at  02/02/15 17:34:51
      Stage 7 of 9: Recovering Database ...
      Error while restoring and recovering database, please check the logs.

  • Upgradding Prime Infrastructure version 1.2 and LMS 4.x to Cisco Prime Infrastructure 2.0

    Hello,
    A customer currently have 2,500 Cisco Prime Infrastructure Lifecycle device license using Prime Infrastructure version 1.2 and LMS 4.x. the customer wants to upgrade to Cisco Prime Infrastructure 2.0.
    Does anyone know if it is possible to upgrade to version 2.0 without additional cost? the licenses from
    Cisco Prime Infrastructure 1.2 has to be upgraded or we need only to rehost the VUDI.
    Also could be possible to upgrade LMS 4.x to Cisco Prime Infrastructure 2.0?
    thanks!

    The two features you mention are two big missing ones. Another is full syslog capability. I don't believe CiscoView or day one support via package updates is included either.
    Another is less tangible - the depth of experience and documentation available for LMS vs. Prime Infrastructure (particularly the wired management features). I agree for wireless PI 2.0 looks good. Some new features are coming for wired that look promising but they are new as of PI 2.0 so I'm taking a wait and see on them.
    I hope to get 2.0 up in my lab in the next week or so and will hope to be pleasantly surprised but that's seldom the case with a major new release.

  • Prime infrastructure nexus 5600 unknown device ?

    Hi All
    Just upgraded prime infrastructure to ver 2.2 but we have a few issues
    One of them is it sees our Nexus 6572 s as unknown devices .
    While trying to deal with another issue with our support we upgraded
    all the newest patches but still this come up as an unknown device.
    Surely cisco have a device patch or something for this
    As i have learnt prime from using it and havent done any training
    perhaps there is something i should know
    Kind regards
    Steve

    Ignore this one just uploaded the latest device patch and this now works
    Steve

  • Cisco Prime Infrastructure 2.2: Catalyst 2960X-24TS-LL Switch Collection Failure

    Hello,
    I've Upgraded Prime Infrastructure to Version 2.2.0.0.158. Now our Catalyst 2960X-24TS-LL switches show an error message, when they are added to the inventory. The error is as follows:
    Partial Collection Failure; Collection Status : Failed feature(s).
    The 2960X-24TS-LL is listed under the supported devices list and other switches (e.g. WS-C2960X-48FPS-L) got inventorized without any problems.
    Did anybody see this issue and can tell me how to solve it.
    - Benjamin

     - Getting that one too, since running 2.2 (Failed Features) ; suggest opening a TAC case.
    M.

  • Problem after upgrade a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2

    I have upgraded a PRIME-NCS-APL-K9 from version 1.1.0.58 to Prime Infrastructure 1.2
    First I have installed the Path "ncs_patch-1.1.0.58-upgrade-pi_1.2.tar.gz" and then the
    "PI-upgrade-bundle-1.2.0.103.tar.gz".
    after the upgade I have got the Message "Upgrade Successful".
    Now when I start the NCS i get the following error message
    egghead/admin# ncs start
    Starting Network Control System...
    Unable to verify hardware.
    This may take a few minutes...
    Health Monitor is already running.
    Failure during Network Control System startup. Check launchout.log for details.
    In the launchout.log are this messages:
    Starting Health Monitor as a primary
    Checking for Port 8082 availability... OK
    truststore used is /opt/CSCOlumos/conf/truststore
    truststore used is /opt/CSCOlumos/conf/truststore
    Starting Health Montior Web Server...
    Health Monitor Web Server Started.
    Starting Health Monitor Server...
    Health Monitor Server Started.
    Starting Remoting Service: Reporting Server
    Checking for running servers.
    00:00 Check complete. No servers running.
    Starting Server ...
    Starting Remoting Service: Reporting Server
    The Report Server startup script is already running waiting for report server to start
    Starting Remoting Service: Reporting Server
    The Report Server startup script is already running waiting for report server to start
    Starting Remoting Service: Reporting Server
    The Report Server startup script is already running waiting for report server to start
    Starting Remoting Service: Reporting Server
    The Report Server startup script is already running waiting for report server to start
    have anyone an idea whats wrong?
    thank you for your help
    Kurt

    i have  the same problem
    NCS/admin# ncs status
    Health Monitor Server is starting.
    Reporting Server is Starting
    Ftp Server is running
    Database server is running
    Tftp Server is running
    Matlab Server is running
    NMS Server is stopped.
    SAM Daemon is running ...
    DA Daemon is running ...
    Syslog Daemon is running ...
    status
    I try it
    To get it back up and running do the following from the CLI.
    1. Stop the NCS
    2. Run 'ncs db reinitdb'
    3. Start the NCS
    but the status is the same

  • Upgrade NCS 1.1.1.24 to Cisco Prime Infrastructure 1.2

    Having a problem installing the ncs_patch-1.1.1.24-upgrade-pi_1.2.tar.gz patch file on a virtual NCS before upgrading it to Cisco Prime Infrastructure 1.2.
    I've followed the Cisco Prime Infrastructure 1.2 Quick Start Guide and did not had the same success as described in the document (see below):
    gmsncs/admin# dir disk:defaultRepo/
    Directory of disk:defaultRepo/
      508376482 Sep 13 2012 05:38:25  backup-20120913-0530.tar.gpg
      853768584 Sep 20 2012 05:40:17  backup-20120920-0530.tar.gpg
         127019 Sep 26 2012 16:40:58  ncs_patch-1.1.1.24-upgrade-pi_1.2.tar.gz
               Usage for disk: filesystem
                     1544204288 bytes total used
                    27185573888 bytes free
                    30293413888 bytes available
    gmsncs/admin# patch install disk:defaultRepo/ncs_patch-1.1.1.24-upgrade-pi_1.2.tar.gz defaultRepo
    Save the current ADE-OS running configuration? (yes/no) [yes] ? yes
    Generating configuration...
    Saved the ADE-OS running configuration to startup successfully
    Initiating Application Patch installation...
    % Local file not found
    Anybody experience with this procedure.
    Thank You
    --- Update ---
    Skipped Step 4 and followed Step 5 in the Quick Start Quide, however now I receive a diffrent error:
    gmsncs/admin# dir disk:/defaultRepo
    Directory of disk:/defaultRepo
      926193986 Sep 26 2012 17:48:12  GRDbackup-120926-1736.tar.gpg
      508376482 Sep 13 2012 05:38:25  backup-20120913-0530.tar.gpg
      853768584 Sep 20 2012 05:40:17  backup-20120920-0530.tar.gpg
         127019 Sep 26 2012 16:40:58  ncs_patch-1.1.1.24-upgrade-pi_1.2.tar.gz
               Usage for disk: filesystem
                     2471309312 bytes total used
                    26258468864 bytes free
                    30293413888 bytes available
    gmncs/admin# patch install GRDbackup-120926-1736.tar.gpg defaultRepo
    Save the current ADE-OS running configuration? (yes/no) [yes] ? yes
    Generating configuration...
    Saved the ADE-OS running configuration to startup successfully
    Initiating Application Patch installation...
    % Manifest file not found in the bundle
    gmsncs/admin#

    Hi, Thank you again for your help, but I am still stuck. I have gathered the outputs from ncs start and a ncs status afterwards. Currently I am not able to access the web-UI of NCS..
    deberncs01/admin# ncs startStarting Network Control System...This may take a few minutes...Dependency Check Failed: Matlab is not running.Dependency Check Failed: Ftp is not running.Dependency Check Failed: Tftp is not running.Failure during Network Control System startup.  Check launchout.log for details.startdeberncs01/admin#deberncs01/admin#deberncs01/admin#deberncs01/admin#deberncs01/admin#deberncs01/admin# ncs statHealth Monitor is running, with an error.failed to start NCS on startup Health MonitorReporting Server is StartingFtp Server is FailureDatabase server is stoppedTftp Server is runningMatlab Server is runningNMS Server is stopped.SAM Daemon is not running ...DA Daemon is not running ...Syslog Daemon is not running ...statusdeberncs01/admin#
    Anyone got a clue on that? and where can I find that launchout.log on NCS? Thank you

  • LMS 4.1 (Windows) & NCS 1.1 (VM) Upgrade to Cisco Prime Infrastructure 1.2

    Hi All,
    Im getting a bit confused about the whole upgrade migration process for the following config to Cisco Prime Infrastructure:
    LMS - Version 4.1 , 500 devices. Windows Server 2008 R2 Standard SP1
    NCS – version 1.1 , 50 devices  Red Hat Linux ( 64 Bit)  (Installation software - NCS-VA-1.0.1.4-small.ova)
    I want to be able to backup databases and migrate licensing from LMS and NCS to one platform. Does anyone have experience of this and could possible guide me thorugh this process. LMS has SAS and NCS has SAU.
    Help will be very much appreciated!!   

    It's a couple of steps but can be done. You may want to reconsider getting off of LMS since the latest Prime Infrastructure (PI 1.2) does not have full feature compatibility with the latest LMS (4.2.3). Have a look here for the comparison.
    If you still want to do it:
    1. Upgrade your NCS to PI 1.2 (instructions). If you're going with a total of 550 devices on a combined license you should use the medium ova file to get the correct server resource allocation. You will need to get the new license from the TAC or via the licensing portal. I'm not sure if you can get the PI license for your LMS upgrade directly via the portal but you do have the entitlement for LMS 4.2 and PI 1.2 (combined licenses not to exceed the original LMS number) if your SAS is current. You may need to contact the TAC and ask for the licensing team.
    2. Upgrade your LMS to 4.2 and patch it to 4.2.2 (instructions). Once you've done that, there is a simple menu command to export your device credentials to Prime (Admin, System, Export Data to PI in LMS and then Operation, Device Work Center, Bulk Import in PI - instruction on Page 18 here). Do that and then in the new PI installation import the devices.
    Verify everything is working and you can decommission the LMS server.

  • Upgrading Cisco NCS 1.1.1.24 to Prime Infrastructure 1.2

    I am planning to upgrade NCS 1.1.1.24 to Prime Infrastructure 1.2 and want to make sure that I understand the process and what to expect.  Any input from those of you that have completed this would be very appreciated.  I am planning on doing the inline upgrade.
    I plan to follow the guide and first install the point patch. ncs_patch-1.1.1.24-upgrade-12.tar.gz
    Then the upgrade image file is PI-upgrade-bundle-1.2.1.12.tar.gz.
    What I want to make sure is that I do not lose any data or maps.  Is this retained?
    We use the NCS Guest Portal for Guest wireless ID administration.  Is this the same in Prime 1.2?
    Thanks.

    The portal guest administration is the same might look different.
    The process is just like you mentioned. Install the patch and then perform the upgrade. When you go to Prime Infrastructure, don't be nervous if it takes PI 10 minutes to boot. That's normal... From the CLI, you can issue a show application status ncs. NCS is case sensitive!
    Sent from Cisco Technical Support iPhone App

  • Poblem after upgrade Prime NCS to Infrastructure

    Hi,
    I just upgrade Prime NCS  1.1.1.24 to 2.0 becuase we had several problem with NCS Aplication, after this upgrade I can´t longer see the Access Point on the floor maps, the APs are still assigned to the map and if I try to edit the location or asign APs to a new map, the aplication keeps loading but doesn´t do anything. I follow the quick installation guide for upgrading and installed the ncs_1_1_1_24-Update.13.4.tar.gz patch.
    thanks for your help

    You should be able to, but your best bet is to bring up a new VM on PI 1.3, and rehost the license.  Then you can export the map's and import the map's on your new VM PI 1.3.  If you try to downgrade, make sure you take a snapshot of the VM, so you can revert in case it doesn't work.
    Thanks,
    Scott
    Help out other by using the rating system and marking answered questions as "Answered"

  • Upgrade NCS 1.1.0.58 - Prime Infrastructure 1.3 or 1.2 - license

    Hi!
    I´m about to upgrade a customers appliance box to PI 1.3. Have anyone done it? and were there any issues with license?
    I guessing an upgrade to 1.2 would be almost the same, license wise. If anyone has input fram that it would also be appreciated.
    Any other input regarding the upgrade is also welcomed..
    Regards
    Fredrik

    As I stated earlier the upgrade went fine but after about three days the database service stopped and wouldnt start again. It required a reinit of the db and then restore the db from backup to get it up again.
    I had a TAC case on this and they gave me info about this in bug # CSCue88178.
    CSCue88178    Inline upgrade from NCS 1.1.0.58 to 1.3 fails to update db schema
    Symptom:
    NCS 1.1.0.58 inline upgrade to 1.3 does not mention any errors during the upgrade process. However the db schema is never actually upgraded, and thus 1.3 does not start.
    Conditions:
    1. Installed ncs_patch-1.1.0.58-upgrade-12.tar.gz pre-patch.
    2. Performed inline upgrade to NCS 1.3.0.20
    Workaround:
    Do not use inline upgrade; use restore upgrade instead.
    This info was not available at the time of my upgrade.

  • Upgrade questions about Prime Infrastructure 1.1.1.24 to 1.3

                   My existing NCS is installed with the small deployment and I'll have a total of 94 AP's but we are installing a new data center and replacing the existing 2 WISM blades for 2 new 5508 WLCs and added 20 more AP'S which will total 114 AP's and 4 controllers. The old WISMs blades and new 5508s will be up together until we migrate exisitng AP's to the new 5508s, so do I need to install the medium deployment since Table for Scaling Prime Infrastructure states:
    Medium: 500 Total. The mix of devices may included up to:
         Wired devices: 300
         Controllers: 5
         Autonomous AP's: 300
         Unified AP's: 300
    Small Deployments are for a total of 250 devices "with up to" 100 Unified AP's and 2 controllers?? 
    Also as part of the download of software for PI 1.3 it   includes Automated Deployment Gateway is this a required piece to install for PI??  We don't use Cisco works so I'm not installing the LMS piece. 
    thank you,
    Sandra

    Isn't it rediculous the message says:::
    Error(s): You must correct the following error(s) before proceeding:
    Error:Unknown Exception Occurred. If the problem persists send logs to Tech Support.
    And the fix is to use a different browser?
    BTW:: Good Idea to try a different browser.  By the looks of the Error Msg, it just didn't look like a browser issue to me so I didn't think to do that but certainly will next time on this and probably many, many, many other issues I see-
    We only spent about an hour chasing our tails around to see what the issue was.
    Again good catch!
    I was speaking w/ another customer today who mentioned if the application were re-written to use HTML 5 these type problems would go away.
    Oh well.
    Glad I could help you get all the way upgraded and all the way up and running and able to push templates to your lightweight APs.
    Cya

  • WCS and LMS to Cisco Prime Infrastructure 1.3 Upgrade

    Hello,
    Our customer is currently having WCS for 500 devices and LMS 3.2 for 1500 devices. We are planning to upgrade to Cisco Prime Infrastructure 1.3.
    I want to check is the upgrade procedure that we have planned is ok or we have missed something.
    Phase 1: WCS to CPI 1.3 upgrade
    1. Check that WCS is at 7.0.230.0  version
    2. Export WCS database
    3. Install NCS 1.1.1.24 software
    4. Contact cisco to obtain trial license for NCS software (L-WCS-NCS1-M-K9 license).
    5. Migrate WCS license and import it in NCS software
    6. Migrate WCS data to NCS software using ncs migrate command
    7. Patch NCS software
    8. Inline upgrade to CPI 1.3 software
    9. Install proper licenses on CPI 1.3 (WCS and LMS device count)
    My concern in this first phase is should I use NCS large image since our Cisco Prime Infrastructure 1.3 software should manage 2000 devices at the end.
    Or is it better not to perform inline upgrade and insted go with exporting data from NCS and then importing them to CPI 1.3 that is going to be installed separately?
    Phase 2: LMS 3.2 to CPI upgrade
    1. Export LMS 3.2 database
    2. Install LMS 4.2 software
    3. Install license to LMS 4.2
    4. Restore data from LMS 3.2 to LMS 4.2
    5. Direct upgrade from LMS 4.2 to 4.2.2
    6. Export the device list with credentials from LMS 4.2.2  and import it as a Bulk Import in CPI 1.3
    At the end we will have CPI 1.3 and LMS 4.2.2 software running.
    Is it possible to directly upgrade from LMS 4.2 to LMS 4.2.4 and then import data to CPI 1.3 or we need to go with 4.2.2 version?
    Regards,
    Jelena

    Hello Marvin,
    We have restored LMS 3.2 SP 1 database on LMs 4.2 and we have got some error messages during restore. Please see our restore output:
    [kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/res
    resolver.pl           restoreDBTableMig.pl  restoreJRMMig.pl      restorebackup.pl     
    [kalms4/root-ade ~]# /opt/CSCOpx/bin/perl /opt/CSCOpx/bin/restorebackup.pl -d /opt/BKP/
    Restore started at : 2013/12/05 14:11:58
    Please see '/var/adm/CSCOpx/log/restorebackup.log' for status.
         USER ID is ..................................... : sysadmin
         OS of the backup archive is..................... : Windows
    INFO:The backup archive is from a different OS. Your current Platform is: Soft Appliance .
    You are attempting to perform a Cross Platform Restore..
    Do you wish to continue (Y/N) [Y] :Y
         Generation to be restored is ................... : 0
         Backup taken from............................... : /opt/BKP/
         Common Services version in the backup data is... : 3.3.1
         Common Services is installed in................. : /opt/CSCOpx
         The temp folder for this restore program........ : /opt/CSCOpx/tempBackupData
         Applications installed on this machine ......... : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][cwportal][ipm][upm][cvw][cwlms]
         Applications in the backup archive ............. : [Common Services][Campus Manager][Resource Manager Essentials][Device Fault Manager][opsxml][cwportal][ipm][upm][cvw]
         WARNING: The list of applications installed on this CiscoWorks server does not match the list of
                  applications in the backup archive. If you restore data from this backup archive,it may
                  cause problems in the CiscoWorks applications.
                  Do you want to continue the restore operation?  (y-continue or n-quit, y/n)?Y
         Applications to be restored are................. : [Common Services] [Campus Manager] [Resource Manager Essentials] [Device Fault Manager] [cwportal] [ipm] [upm] [cvw]
         Available disk space in NMSROOT................. : 86451488 Kb
         Required disk space in NMSROOT.................. : 35906524 Kb
         (The temp and NMSROOT are on same device, therefore this required disk space includes temp space)
      Copying the backup files to the temporary location [/opt/CSCOpx/tempBackupData]
      preRestore of [Common Services] has started.
      preRestore of [Common Services] has completed.
      preRestore of [Campus Manager] has started.
      preRestore of [Campus Manager] has completed.
      preRestore of [Resource Manager Essentials] has started.
      preRestore of [Resource Manager Essentials] has completed.
      preRestore of [Device Fault Manager] has started.
      preRestore of [Device Fault Manager] has completed.
      preRestore of [cwportal] has started.
      preRestore of [cwportal] has completed.
      preRestore of [ipm] has started.
      preRestore of [ipm] has completed.
      preRestore of [upm] has started.
      preRestore of [upm] has completed.
      preRestore of [cvw] has started.
      preRestore of [cvw] has completed.
      doRestore of [Common Services] has started.
              Cross Platform Update started.
              Cross Platform Update completed.
              License check started.
                 WARNING: The license details in the server are different from the backup data.
                          After restoring, please check the license available in the server.
                 WARNING: Your current license count is lower than your earlier license count.
                          If you restore the data now, devices that exceed the current licence count
                          will be moved to Suspended state.
              License check completed.
              Restoring certificate.
                 WARNING: Cannot evaluate the hostname, hence the certificate
                          may be from this host or another host.
                          [  Certificate not overwritten  ]
              Restored Certificate.
              Restoring Common Services database.
              Restored Common Services database.
              Restoring CMIC data.
              Restored CMIC data.
              Restoring CMC data.
              Restored CMC data.
              Restoring Security Settings.
              Restored Security Settings.
              Restoring DCR data.
              Restored DCR data.
              Restoring Certificate key store.
              Restored Certificate key store.
      Restoring DCNM CrossLaunch data.
              Restored DCNM CrossLaunch function.
              Restoring JAAS configuration.
              Restored JAAS configuration.
              JRM Job Migration started.
              JRM job Migration done.
      doRestore of [Common Services] has completed.
      doRestore of [Campus Manager] has started.
              Cross Platform Migration for Campus started.
    Cross Platform update Starts for Campus
      doRestore of [Campus Manager] has completed.
      doRestore of [Resource Manager Essentials] has started.
    10% of RME  Restore completed
    30% of RME  Restore completed
    50% of RME  Restore completed
    70% of RME  Restore completed
    100% of RME  Restore completed
      doRestore of [Resource Manager Essentials] has completed.
      doRestore of [Device Fault Manager] has started.
    10% of DFM Restore completed
    30% of DFM Restore completed
    50% of DFM Restore completed
    80% of DFM Restore completed
    Going to modify Eight PM report 
    Modified Sucessfully Eight PM report 
    100% of DFM Restore completed
      doRestore of [Device Fault Manager] has completed.
      doRestore of [cwportal] has started.
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.script  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.script
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db//portal.log  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/db/portal.log
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultUserCommunity.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultUserCommunity.properties
      Src file : /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties//defaultCommunity.properties  ,,, Destination file : /opt/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
    File Copied: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
    Error while coping the File: /opt/CSCOpx/tempBackupData/cwportal/CSCOpx/MDC/tomcat/webapps/cwportal/WEB-INF/classes/data/ciscoWorks/properties/defaultCommunity.properties
      doRestore of [cwportal] has completed.
      doRestore of [ipm] has started.
            10% of IPM Restore Completed
            30% of IPM Restore Completed
            50% of IPM Restore Completed
            60% of IPM Restore Completed
            70% of IPM Restore Completed
            100% of IPM Restore Completed
      doRestore of [ipm] has completed.
      doRestore of [upm] has started.
    HUM database restore starts
    INFO:STOP= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
    SQL Anywhere Command File Hiding Utility Version 10.0.1.4239
    INFO: Database Shutdown is in Progress..Please wait
    INFO: Stop Engine Args= /opt/CSCOpx/objects/db/bin64/dbstop -q -y -c dsn=upm
    INFO: After Database Shutdown RC= 2304
    root=C:\PROGRA~2\CSCOpx\databases\upm\upm.db
    DBUTILS: Inside Cross Platform
    INFO: Current Database password does not match the password of Database being restored
    INFO: Using the Password of the Database being restored
    HUM database restore successfully completed.
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Threshold/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Custom/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Poller_Failure/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/TrendWatch/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Availability/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPORTUtilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Memory_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_Availability/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Threshold_Violations/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/CPU_Utilization/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/PoEPSEConsumption/README.txt
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate
    File :/opt/CSCOpx/MDC/tomcat/webapps/upm/reports/Quick/Interface_ErrorRate/README.txt
    Directory is reportsStarted changing property .
    linux
    Restored HUM configuration file successfully.
      doRestore of [upm] has completed.
      doRestore of [cvw] has started.
      doRestore of [cvw] has completed.
      postRestore of [Common Services] has started.
      postRestore of [Common Services] has completed.
      postRestore of [Campus Manager] has started.
      postRestore of [Campus Manager] has completed.
      postRestore of [Resource Manager Essentials] has started.
      postRestore of [Resource Manager Essentials] has completed.
      postRestore of [Device Fault Manager] has started.
      postRestore of [Device Fault Manager] has completed.
      postRestore of [cwportal] has started.
      postRestore of [cwportal] has completed.
      postRestore of [ipm] has started.
      postRestore of [ipm] has completed.
      postRestore of [upm] has started.
      postRestore of [upm] has completed.
      postRestore of [cvw] has started.
      postRestore of [cvw] has completed.
    Restored successfully.
    Are this errors going to affect our LMS 4.2 operations?
    Then we have upgraded to LMS 4.2.2 and exported data and credentiales for PI import.
    On PI 1.3 we have installed WCS 500 devices upgrade license and LMS 1500 upgrade license and now we are having 2000 devices lifecycle license. We have successfully restored WCS data in PI and we have imported LMS devices as bulk import. What is strange is that we have this message in prime regarding licensing:
    On LMS 3.2 our customer had saved unlimited number of configuration versioning. After upgrading to LMS 4.2 we can only see last 3 configurations regardless of unlimided number of configurations in previous LMS, so my question is where can we find older configurations in LMS 4.2?
    We are planning to turn unlimited versioning on CPI 1.3 now, so our customer will again have feature that they need. Do you have some experiance regarding disk space when all device configurations are stored forever?
    Thank you for your help.
    Regards,
    Jelena

Maybe you are looking for

  • Problem in Runtime Workbench.

    I am getting the following when I click on rwb: Components Domain ??? (domain.00.hmxid1) Integration Server Integration Engines Non-Central Adapter Engines     Adapter Engine SXD (hmxid1)  J2SE Adapter Tools and in message monitoring I am getting *ja

  • JSlider Enabled Coloring

    I have a JSlider and I am trying to write an extended UI which does not make the slider labels turn Gray when I call slider.setEnabled(false); (Note that when a JSlider is disabled, the labels and tick marks turn gray) In particular, I want the JSlid

  • How to paste to a JTextField

    Hello, I have my copy and paste buttons working for a text area. But im trying to get my program to work that I open a browser from the main applet menu and i want to be able to copy from my text area and paste it into my URL text field in my my brow

  • Data multiple selection

    Hi, Is it possible to transfer multiple selections list of data in an item to another item , in the branch area? Thanks in advanced Ilan

  • Cartridge(s) not detected

    We have a HP 4280 Photosmart printer.  The following message suddenly appeared on the printer.  "Printer cartridge(s) missing or not detected". Both cartridges have been used for some time with no problem.  When I checked the ink levels the color car